First minutes after water
If your phone falls in water, take it out right away, turn it off, and don't charge it. Tech Service in Almaty accepts such phones for free diagnostics, cleans the board from oxidation, and repairs in the service center or at your home—a technician arrives within 60 minutes. 1-year warranty on labor and parts.
The faster you take the device out and cut the power, the less moisture reaches the board. Below is the step-by-step procedure that technicians follow.
Take the phone out and turn it off immediately
The first thing to do is take the device out of the water and turn it off without checking if it works. Hold the power button until the slider appears and slide it, or if the screen doesn't respond, press and hold the button longer and wait for the display to go dark. The battery inside stays energized while the gadget is on, and any drop on the board contacts can short the circuit. A short circuit on the board most often damages the power controllers and the processor—such a repair is more expensive and takes longer than a regular cleaning from oxidation. Every second under power increases the risk of a short circuit, so turning it off is more important than trying to "see if everything is fine." Don't press buttons repeatedly to check the response: even a brief power-up sends current through wet traces and starts contact corrosion. If your phone fell in water, what to do first is the most common question, and the answer is always the same: cut the power to the device before any other manipulations.
Remove the SIM card and memory card
- SIM ejector tool or paperclip: find the tool for the tray in advance so you don't scratch the body in a hurry.
- SIM card tray: pull it out all the way and leave it open—this lets moisture escape from the slot.
- Memory card: remove it separately, wipe with a dry cloth, and leave it in the air.
- The tray itself: don't put it back until the device is dry and has been diagnosed.
- Slots: don't poke inside with a cotton swab—lint remains on the contacts and interferes with their operation.
- Slot contacts: inspect them against the light, but don't rub the metal—micro scratches speed up oxidation of the traces.
Blot the body and don't shake the device
Blot the body with a soft cloth and hold the device with the connector facing down so water flows out rather than going deeper. Wipe the buttons, ends, and speaker grille—drops accumulate there and then flow inside. Leave the charging port open and don't plug it with paper or cotton. The board oxidizes under the influence of moisture and oxygen, and this process continues even after the body looks dry. Sharp shaking spreads drops through the inner layers of the board, so it's better to let the water drain calmly—tilt the gadget with different ends in turn and hold it like that for a few seconds. If you hear gurgling in the speaker, don't blow inside: you'll push the water deeper toward the flex cables. Change the cloth as soon as it gets wet—a wet cloth smears moisture over the body instead of removing it.
What not to do and why
Most folk drying methods do more harm than the water itself. Let's look at what not to do with a wet device and why these actions are dangerous for the board.
Don't turn on or charge the device
You must not turn on, let alone charge, a device that has fallen into water, even if it looks working. Applying power to a wet board triggers heating and contact corrosion, so "checking with a charger" often becomes the cause of the breakdown. Drops remain in the charging port and under the screen, and when current is applied, they turn into conductive paths between adjacent contacts—that's a short circuit. The battery heats up in this situation, and the device in your hand becomes hot: this is the sign most often described as "I charged it and it's heating up." If the device turns on by itself after falling into water and shows a working screen, it doesn't mean it's dry inside—the board may stay wet for several hours. Turn it off and don't touch the power button until inspection: power on a wet board is the fastest way to oxidation that will show up later.
Why rice and a hair dryer don't dry the board
- Rice and silica gel: they only absorb moisture from the surface and from the air nearby, and never reach the inner layers of the board.
- Hair dryer: hot air pushes droplets deeper into the case and spreads moisture across the board instead of evaporating it.
- A day in grains: creates the illusion that it has dried out, while corrosion continues inside the case and eats away at the contacts.
- Trial run: turning it on after rice triggers the same reaction with heating and a short circuit.
- Film and bag: an airtight package with rice traps moisture inside instead of removing it.
What else you shouldn't do with a wet device
Don't take the device apart yourself and don't try to blow it out with a compressor or a vacuum cleaner. Home disassembly often damages the moisture-proof seals and flex cables, and the airflow drives droplets deeper into the case. A pressurized compressor tears the thin membranes of the speaker and microphone, a vacuum cleaner pulls moisture along with dust straight to the connectors, and a hair dryer pushes water deeper with hot air. Even careful prying without tools leaves scratches on the case and tears off the screen's adhesive frame — you'll have to replace it anyway. The case and seals are designed for factory assembly, and after home interference the tightness is not restored. It's better to leave opening and cleaning the board to a technician: they will remove the screen without damage and dry the board disassembled, not just from the outside.
Why salt water and other liquids are more dangerous
Not all water is equally dangerous for electronics. The composition of the liquid determines the rate of corrosion and what to do first — and what to do when your phone falls into water depends on exactly what it fell into.
Fresh water from a tap or puddle
Fresh water damages a phone more slowly than salt water, but oxidation of the board still starts within the first hours. The phone's board oxidizes under the influence of moisture and oxygen: the traces and contacts become covered with a thin layer of oxide that makes signal transmission worse. Tap water comes with chlorine and mineral impurities, puddle water with sand and organic matter, and both leave a salt residue on the board after drying. Moisture penetrates through connectors, speakers, and case seams, even if the device looks dry on the outside. Even after fresh water, a phone may work for a day or two and then fail, so diagnostics shouldn't be delayed until symptoms appear. The sooner the device gets to a technician, the fewer traces will need to be restored after cleaning.
Salt and chlorinated water
Salt and chlorinated water is the most dangerous because salts and chlorine accelerate corrosion of contacts and the board many times over. Sea water contains dissolved salts that act as an electrolyte: a microcurrent arises between neighboring contacts, and the metal corrodes right under the layer of moisture. Chlorine in pool water attacks metal even more aggressively, and after drying, crystals remain on the board that continue to draw moisture from the air. Rinsing the case from the outside is not enough — salt deposits remain on the board and under the shields. After the sea or a pool, the phone needs not just drying but rinsing the board with a special solution, otherwise the salts keep eating away at the contacts. A technician performs such rinsing with the device disassembled so the solution reaches hidden areas of the board.
Sweet drinks and other liquids
| Liquid | Why it's dangerous | What to do urgently |
|---|---|---|
| Coffee, tea, soda | Sticky layer holds moisture | Turn off, don't dry with a hair dryer |
| Juice, milk | Nutrient medium for mold | Rinse the board with a solution |
| Ketchup, sauce | Thick residue on contacts | Clean off oxidation |
| Perfume, lotion | Alcohols and oils corrode | Disassemble, rinse the board |
How to tell that water has damaged the board
A device after water often works as if nothing happened, then fails a few days later. Let's look at the signs that show moisture has already reached the board.
How soon the board starts to oxidize
Oxidation of the board starts within hours of water exposure, but shows up as a failure days or a week later. Moisture gets trapped behind the screen, in connectors, and around the metal shields of microchips where you can't see it from the outside: the droplets dry, but dissolved salts and minerals keep eating away at contacts and traces. Fresh tap water starts the process more slowly, while salt water and chlorinated water speed it up because they contain more impurities. Thin traces and solder joints are the first to suffer, then the components themselves. Meanwhile, the person sees the device turn on, make calls, and hold a charge, so they put it back in their pocket. That's why "it works, so it's fine" is misleading: corrosion progresses under working components and surfaces later.
Symptoms you notice right away
| Symptom | What it means | Action |
|---|---|---|
| Heating up without load | Moisture behind the screen or near the battery | Turn it off and don't charge |
| Turns off by itself | Power fluctuations on the board | Don't turn it back on |
| Touchscreen glitches | Oxidation of the display flex cable | Don't press on the screen |
| Sound is gone | Moisture in the speaker or microphone | Dry the outside of the case |
| Won't charge | Oxidized charging port | Don't plug in the cable |
What board oxidation means in the technician's words
Board oxidation is corrosion of contacts and traces caused by moisture, which we find during free diagnostics. The technician opens the case, examines the board under magnification, and finds the characteristic film on connectors, darkened solder points, and damaged traces—these are the signs of corrosion. Our diagnostics are free, so the extent of the damage is clear before any work begins: the technician determines which areas are affected and what can be done about them. In the early stage, oxidation is removed by cleaning, but in the later stage damaged components have to be replaced, so how soon you bring the device in directly affects the scope of work. We provide a 1-year warranty on labor and parts, so after cleaning or component replacement, the client isn't left alone with a breakdown.
What to do about data and water resistance
After water damage, people usually ask two things: will the contents of the storage survive, and will the device withstand immersion thanks to its water resistance. Let's go through both questions one by one.
Will photos and contacts be saved
Data is usually recoverable if the storage and board aren't critically damaged and the device wasn't turned on after water exposure. Photos and numbers are stored in a microchip attached to the board: as long as corrosion hasn't touched the traces, the contents can be read. If cloud sync was enabled, part of the archive is already on the server, and then access to it doesn't depend on the device's condition. A backup is the simplest way to preserve photos and numbers before repair, and it's worth checking on another device while the wet phone dries out. The worst case is for those who kept the device turned off for a day but never brought it in for inspection: during that time, oxidation products reach the traces. The sooner the gadget gets to diagnostics, the higher the chance of extracting the contents before corrosion affects the storage.
How to prepare before going to the service center
- Account password: recall and write it down in advance—without it, the technician can't check the data on the device.
- Sync enabled: check from another device whether the archive is uploading to your account—this will speed things up.
- Backup: if sync was working, some photos and numbers are already in the cloud, and we can rely on it during repair.
- What to tell the technician: name the liquid, the time of the drop, and whether the device was turned on—these details affect the order of work.
- Memory card data: mention whether there was a memory card in the phone and whether you removed it—information is read from it separately.
Does IP68 water resistance protect against water
IP68 water resistance reduces the risk, but it doesn't guarantee the device will survive a drop into water. The rating is based on lab conditions: fresh water, a specific depth and time, and an intact case. In reality, the seals around the screen, SIM tray, and buttons wear out from daily use, and impacts and pressure changes—from dropping it in the sink or diving—break their fit. Through microcracks in the case, water reaches the board even if the glass is intact. So any device, regardless of its protection rating, still needs diagnostics after contact with liquid, not just a check of whether it turns on. In my opinion, the promise that "nothing will happen" is more dangerous than the water itself: people delay inspection until corrosion affects the traces.
When to bring it to a service center in Almaty
Some devices can only be saved in the first hours, so let's go over when a visit to a technician is essential and how it works in the southern capital.
When a visit to a technician is essential
You should bring the device to a service center if it won't turn on, heats up, glitches, or fell into salt water—even if it seems to work. After contact with moisture, the board corrodes invisibly: contacts get a greenish film, traces lose conductivity, and after a few days the device may stop turning on for no apparent reason. If the screen shows lines, the speaker crackles, the camera fogs up from inside, or the touchscreen responds with a delay—these are also signs that liquid has reached the flex cables and connectors. A separate case is falling into the sea or a chlorinated pool: salt and chemicals eat metal faster than fresh water, so such a device should be inspected within the first day, not when it dries out. Repair after water damage is almost always cheaper and more reliable than buying a new device, as long as the board isn't completely destroyed by corrosion.
How we work in Almaty
At Tech Service, we work as a direct provider with our own technicians and arrive at your home within 60 minutes anywhere in the city. On-site repair is convenient when you need the device urgently or don't have time to go to the workshop: the technician comes to your address and inspects the device, then performs the cleaning from oxidation at the service center. Technicians with 4 to 20 years of experience provide free diagnostics and quote the cost of work after it, and there is a 1-year warranty on labor and parts. Diagnostics show whether moisture has reached the board and whether cleaning makes sense. You can pay via Kaspi QR, Kaspi Red, bank card, cash, or bank transfer for companies. In my opinion, the home visit is especially helpful for residents of remote areas—the trip to the workshop and back eats up half a day, while here the technician comes to your address.
What to bring and what to tell the technician
- The device and charger: bring the device itself and its charger—the technician will check how it behaves when connected to power and assess the condition of the connector.
- Liquid and time: remember what exactly the device fell into—fresh water, salt water, a sugary drink—and how many minutes it was submerged; this affects the method of cleaning from oxidation.
- What you've already done: tell us if you dried it with a hairdryer, put it in rice, or tried to turn it on or charge it—such attempts change the picture of board damage.
- SIM card and memory card: bring them separately if you removed them; the technician will check the contacts and the condition of the slots.
- Payment: we accept Kaspi QR, Kaspi Red, card, cash or bank transfer, and the technician quotes the cost of work after free diagnostics.
What to remember about water damaged phones
Briefly about what determines the outcome: the speed of your first actions, avoiding dangerous "folk" methods, and the willingness to show the device to a technician before obvious malfunctions appear.
- Take it out and turn it off immediately: the sooner the smartphone is powered down, the lower the chance that moisture will short the contacts under voltage.
- Don't turn it on, don't charge it, don't dry it with rice or a hairdryer: heat drives water deeper, and rice leaves dust and starch on the board.
- Salt water is more dangerous than fresh: salt and chlorine speed up corrosion, so delay here costs more.
- Oxidation shows up days later: the gadget may work for a day, then start rebooting or lose network.
- For any symptoms—get diagnostics: waiting until complete failure is not worth it; an early inspection saves more working components.








