Геннадий Ж.Order No. 2601-4185 · 28 October 2026
oursПозвонил в четыре места, тут ответили по-человечески. Открыл — и сразу понял: не морозит. Замена: компрессор. Сравнивал — здесь дешевле. Ни шума, ни запаха, всё штатно.
City
Language
What broke
Sections
Message on WhatsApp+7 (778) 746 00 26Mon–Fri 10:00–19:00, Sat–Sun 11:00–18:00
A technician arrives within 60 minutes anywhere in the city. Diagnostics are free.
Our own technicians4 to 20 years of experience




Repair prices
Select the symptom that matches your Sharp refrigerator's behavior
refrigerant leak, clogged capillary tube
from5 000 ₸
defrost sensor, heating element, timer
from5 500 ₸
clogged drain, misaligned trough
from4 500 ₸
compressor wear, loose mounts
from16 000 ₸
code points to a specific component
from5 500 ₸
fan, sensor, defrost heater
from5 500 ₸
start relay, low voltage
from5 500 ₸
temperature sensor, thermostat
from6 000 ₸
The table lists the 'from' price for labor, for common jobs also the 'from' price of the part, plus the time required to complete the job.
1 visittime
from 4 500 ₸cost

BeforeAfter5 steps

Five steps from request to checking the appliance after repair.
Describe the symptoms over the phone and provide your Sharp refrigerator model so the technician brings the right tools.
The technician clarifies which components to check for the specific symptom from your request and agrees on the scope of diagnostics.
The technician asks about the history of the issue and operating conditions of your refrigerator before starting work.
After the work, the technician cleans up the workspace and returns removed parts as agreed.
Check the refrigerator's operation in the first hours after turning it on and ask the technician any care questions.
We reply during working hours
Describe the issue with your Sharp refrigerator and leave a request — the technician will coordinate a visit time and clarify details with you.

Warranty question? Call us
+7 (778) 746 00 266 127 reviews of repairs at TECH SERVICE in total
Геннадий Ж.Order No. 2601-4185 · 28 October 2026
oursПозвонил в четыре места, тут ответили по-человечески. Открыл — и сразу понял: не морозит. Замена: компрессор. Сравнивал — здесь дешевле. Ни шума, ни запаха, всё штатно.
Наталия С.Order No. AS-4046 · 24 August 2025
oursПереезжали в новую квартиру, техника после перевозки захандрила. С утра заметил: не морозит. Сейчас пашет без нареканий.
Лариса О.Order No. AST-2503-174 · 5 February 2025
oursИскал, кто работает в субботу, у нас с женой график сложный. С этим и пришёл: намерзает лёд. Вернули — проверил, всё ок!!
Наталия С.Order No. 53082 · 25 January 2025
oursСмотрел, чтобы был свой склад запчастей, а не под заказ. Причина обращения — шумит. Дильмурат С всё сделал при мне, за пятнадцать минут. Нагрев в норме, посторонних звуков нет.
Борис В.Order No. 2502-4413 · 17 January 2025
oursЖалоба одна: шумит. Никита М сам позванил и сказал, что готово. Ни разу не пожалел.
Любовь Ю.Order No. AST-2210-389 · 11 May 2022
oursБыло важно успеть до конца недели, а то морозы обещали. Привёз на диагностику: холодильник. С чем обратился: намерзает лёд. Никита М отсоветовал дорогой ремонт, предложил простой. По деньгам вышло ровно, без сюрпризов. Перезвонили на следующий день, уточнили детали. Пришлось ставить: модуль. Ни разу не пожалел.
Альбина Ю.Order No. AST-2001-960 · 27 April 2020
oursЗаявку оставил через сайт вечером, утром перезвонили. Думал, попал на дорогой ремонт. Симптом как на ладони: шумит. В другом месте просили на треть больше. Полёт нормальный.
Юрий М.Order No. AS-9458 · 7 May 2018
oursИскал, кто работает в субботу, у нас с женой график сложный. Заявку оставил на всякий случай, а зря время тянул. Первое, что заметил: шумит. Никита М сам позванил и сказал, что готово. Созвонились, уточнили модель, срозу сказали по запчасти. По факту меняли: модуль. Tech-service посоветовали в домовом чате. Пользуюсь и вспоминаю добрым словом.
Инна Н.Order No. 1709-5286 · 30 October 2017
oursСимптом как на ладони: шумит. Дильмурат С пообещал и сделал, без напоминаний. Работает, даже лучше прежнего.
Инна Н.Order No. AS-5681 · 20 August 2016
oursБольше всего мешало: намерзает лёд. Дильмурат С объяснял без умных слов, за это спасибо. Выбрал techservice, потому что близко к работе. Сейчас пашет без нареканий.
experience11 yearsDishwasher repair technician
experience10 yearsSenior washing machine technician
experience11 yearsStove and oven repair technician
experience11 yearsFreezer repair technician
experience16 yearsWashing machine installation technician
experience8 yearsDishwasher technician
experience12 yearsWashing machine repair technician
experience10 yearsWashing machine board repair technician
Didn’t find the answer? Message us on WhatsApp.
Ask a questionMost often they push unnecessary work and exaggerate the problem. Ask which part is being replaced and why, and the technician should quote the price after a free diagnostic, not over the phone.
Yes, the board is usually restored rather than replaced entirely: burnt components are found and resoldered. It depends on the model and the extent of damage after a power surge.
Don't plug it in again or take it apart yourself: the control board or start relay may be damaged. Unplug it from the mains and call a technician, who will check the electronics after a free diagnostic.
Sharp codes vary by model: the same combination may point to a sensor, defrost system, or board. Check the code against your model's manual, and the technician will identify the exact cause.
Technically yes, but without experience the door often doesn't fit tightly after replacement and ice starts to build up. A technician will select the right seal for your model and adjust the door so it closes tightly.
No Frost doesn't require a full defrost, but it's a good idea to unplug it for a few hours once a year to clean the drain and remove odors. If ice still builds up, the cause is a malfunction, not maintenance.
Tech Service repairs Sharp refrigerators in Astana at your home: our technician arrives within 60 minutes anywhere in the city, diagnostics are free, and there's a 1-year warranty on labor and parts. Technicians with 4 to 20 years of experience know their way around this brand's inverter compressors, control boards, and No Frost system.
Sharp has its own weak points — the inverter compressor, control board, and No Frost system. Let's break down the signs that tell the owner which component has failed.
If the light is on but there's no cold, the power and board are partially alive — most often the compressor, start relay, or a refrigerant leak in the circuit is to blame. In such cases, the motor either stays silent or hums without building pressure; the start component, when worn, clicks and doesn't hold the winding, and refrigerant escapes through microcracks in the foamed circuit or at solder joints. A leak shows up differently: sometimes the unit cools but weakly, sometimes cold disappears in both compartments at once. The control board is checked only after the motor and circuit tightness are ruled out. Start by listening for compressor hum and start component clicks — that sound helps the technician narrow down the causes before the visit.
Frost on the back wall with a warm fridge compartment is a typical No Frost failure: defrost doesn't kick in, and ice blocks the air channels. Sharp's defrost circuit includes the defrost heater, defrost timer, and defrost sensor — failure of any one stops the cycle, and the fan blows air past the frozen evaporator. The picture is misleading: the freezer ices up while the fridge compartment stays warm. The frost layer builds up gradually over several cycles, and at first only the top shelf suffers, then cold is lost throughout the compartment. Before blaming the electronics, check the door seal — a loose gasket gives the same picture and often masquerades as a No Frost breakdown.
A click and silence instead of startup usually points to the start relay, while continuous running without shutting off points to a refrigerant leak or a faulty thermostat. The start component is replaced as a separate unit, whereas continuous motor operation without pauses means the unit isn't reaching temperature and is trying to compensate for lost refrigerant. The thermostat in such a scheme may be fine — its readings just don't match the actual temperature in the compartments, so both sensors and the circuit itself are checked. The Sharp inverter compressor doesn't always click — its failure is gradual, through loss of cooling, so diagnostics start with the board, not the motor itself. A conventional motor with a worn winding hums and trips the protector, while an inverter one silently goes into an error on the board — the difference in symptoms determines what to check first.
The Sharp display doesn't show a code for nothing — each one points to a specific component. Let's look at how to read the panel signals and when the board is at fault versus the compressor.
A code on the Sharp display is a fault address: it points to a sensor, defrost component, or communication with the compressor, and a flashing indicator usually duplicates the same signal without digits. The panel looks different across series: multi-door models have a segmented screen with alphanumeric designation, while two-door models have a row of LEDs where one flashing light encodes the zone. The combination of flashes and a beep on some models repeats in a cycle — count the flashes until the pause, that's the group number. If the screen goes completely dark while the fridge hums, it's about the control board power, not a sensor. Note the code and model before the technician arrives — with that pair, they can determine which component to check first and not waste the visit guessing.
| Code group | What it points to | What the technician checks |
|---|---|---|
| Sensor signal | defrost or temperature sensor | sensor resistance, circuit to the board |
| Defrost failure | heating element, timer, or defrost sensor | heating element operation, timer activation |
| Communication failure | control board, wiring harnesses | contacts, board traces |
| Compressor problem | start relay, motor windings | start-up, current, windings |
| Fan malfunction | No Frost circulation fan | rotation, winding, duct blockage |
After a power surge, Sharp refrigerators often burn out the control board rather than the compressor — the fridge stays silent even though the motor is fine. We check the electronics and windings separately to avoid replacing a working component: we test the motor windings for resistance and insulation resistance, then apply power to the board and see if the control signal reaches the compressor. The symptoms are similar — silence instead of the usual hum — but the cause is different: a burnt-out board often doesn't respond to buttons and the panel doesn't light up, while with a dead motor the panel works but there's no start-up. If the fridge won't turn on after a thunderstorm or power surge, don't rush to replace the compressor — in most such cases the electronics are to blame, and repairing them costs less.
Some checks a Sharp owner can do in five minutes — this helps avoid an unnecessary service call and describe the problem more accurately over the phone.
You can realistically clean the seal and defrost the fridge yourself, but replacing the seal, start relay, and especially the control board is best left to a technician — a makeshift job can easily damage the component. The door seal is glued on and requires fitting at the corners, hinges are adjusted to the specific cabinet geometry, the start element is matched to the compressor, and the electronic module to the model and firmware version. A loose seal creates a gap that makes frost return faster than before replacement, and an incorrectly selected start component can burn out the motor winding. At the same time, cleaning the seal with mild soap and a full defrost with doors open are operations that residents of the capital can perform without risk to the appliance. If cold doesn't return after these steps, you need a technician with tools and experience on Sharp.
We repair Sharp refrigerators in Astana at the client's home — from free diagnostics to a final cold check. Here's the order of steps and what each includes.
We take your request, a technician arrives within 60 minutes anywhere in the city, performs free diagnostics, agrees on the work and cost, does everything on-site and checks the cold after reassembly. On site, they open the compartments, test the motor windings, check the control board and the pressure in the circuit — these measurements show whether the unit has failed or the control is at fault. Agreeing before work starts defines the list of replacements, so there are no disputes about the scope later. We repair Sharp refrigerators in Astana with a visit to the client: the technician works on-site or at the service center. We provide a 1-year warranty on labor and parts — this fixes responsibility for the result, not just for the visit.
| Work | When needed | What we check next |
|---|---|---|
| Starter relay replacement | clicking, motor won't start | stable starting |
| Compressor replacement | not holding cold | pressure, cold |
| Control board repair | error code, won't turn on | response to commands |
| No Frost restoration | ice buildup, warm compartment | defrost and airflow |
| Refrigerant recharge, circuit soldering | leak, weak cold | tightness, temperature |
| Seal and hinge replacement | loose seal, ice buildup | seal pressure around the perimeter |
In an inverter Sharp, the compressor is controlled by the board, so diagnostics start with the electronics, not the motor; the compressor itself is more often replaced than repaired. The technician reads signals from the board, compares them with the behavior of the windings, and only then draws a conclusion about the component — otherwise replacing the motor hits your wallet without result. The inverter motor runs at variable frequency, and its health can't be judged by eye: you need to check the board signals. The mistake of 'replace the compressor right away' costs more than a second visit — electronics first, mechanics second. Moreover, on such models we check the relay and starting automation separately: they fail more quietly and don't always show a code on the display. This order saves both time and parts.
A technician who takes on everything and a Sharp specialist are different stories. Let's look at how to tell a professional and what the warranty after work gives you.
We provide a 1-year warranty on labor and parts — this covers compressor replacement, control board repair, and No Frost adjustment. The warranty applies to the entire scope of work performed, not just a separate operation the technician considered main. Our specialists have been working with the brand for 4 to 20 years, so they find the fault by symptom and error code, not by replacing components one by one. The warranty on parts is more important than the warranty on labor: it covers the component itself, not just the installation. Before agreeing to work, ask what the warranty covers — labor, the part, or both; the difference shows up if you need to call again.
If the cooling disappears again after the repair, we come back under warranty and find out why. First, we compare the readings with the original diagnostics, then check the cooling circuit for refrigerant leaks and the door seal for tightness. Most repeat visits are not caused by the replaced part but by a related leak or a loose seal — that's why on the first visit we check the entire circuit, not just the obvious symptom. The owner should write down the error code that appears the second time: it shows whether the same fault has returned or a new one has appeared. This approach saves both our trip and your time — the cause is found right away, without taking everything apart again. If the cooling doesn't come back after the first visit, don't disassemble the unit yourself: cables and sensors moved during disassembly distort the picture, and the technician has to start the check all over again.
Troubleshooting Sharp breakdowns comes down to simple logic: first the symptom, then the error code, then checking the part. Below is a quick summary to help you keep the steps in order.
90brands
We work with every brand sold in Kazakhstan — from Samsung, LG and Atlant to Biryusa, Indesit, Stinol and rare imported makes. Can’t find yours in the list? Call anyway — a technician will come and take a look.
Tech Service technicians repair other appliances too — with the same 1-year warranty on labour and parts.
Refrigerator Repair in Almatyfrom 3 000 ₸
Washing Machine Repair in Almatyfrom 3 000 ₸
Dishwasher Repair in Almatyfrom 3 500 ₸
Oven Repair in Almatyfrom 3 000 ₸
Cooktop Repair in Almatyfrom 3 500 ₸
Air Conditioner Repair in Almatyfrom 3 500 ₸
Boiler and Water Heater Repair in Almatyfrom 2 500 ₸
Freezer Repair in Almatyfrom 6 000 ₸
Tumble Dryer Repair in Almatyfrom 5 000 ₸
Coffee Machine Repair in Almatyfrom 2 500 ₸
Robot Vacuum Cleaner Repair in Almatyfrom 3 500 ₸
Vacuum Cleaner Repair in Almatyfrom 1 500 ₸
Microwave Oven Repair in Almatyfrom 2 000 ₸
Hair Dryer Repair in Almatyfrom 1 500 ₸
Iron Repair in Almatyfrom 3 000 ₸
Electric Kettle Repair in Almatyfrom 2 500 ₸
Mixer Repair in Almatyfrom 2 500 ₸
Multicooker Repair in Almatyfrom 500 ₸
If your refrigerator stops working, first check the outlet, the power cord, and the thermostat setting, and after defrosting let it stand for a while.
4 February 2026 · 12 minutes read
If your refrigerator isn't cooling but the light is on, the cause is usually one of the components in the cooling circuit: the compressor, thermostat…
10 December 2025 · 13 minutes read
If your dishwasher won't drain, the most common culprits are a clogged filter or drain hose; less often, it's the pump, impeller…
24 March 2026 · 12 minutes read
A washing machine can hum for many reasons, and the first thing to figure out is when the sound appears.
20 March 2026 · 12 minutes read
If your washing machine isn't filling with water, the most common culprits are a closed valve, a clogged inlet filter screen on the hose…
20 February 2026 · 13 minutes read
If your microwave isn't heating but the light and turntable still work, the problem is usually one of the high-voltage components — the magnetron, diode…
15 February 2026 · 12 minutes read












