Василий Е.Order No. 57801 · 18 May 2026
oursПереезжали в новую квартиру, техника после перевозки захандрила. Привёз на диагностику: дрон. Проблема ровно одна: не держит высоту. Внутри оказалось: плата. Все функции проверил — работают.
City
Language
What broke
Sections
Message on WhatsApp+7 (778) 096 59 61Mon–Fri 10:00–19:00, Sat–Sun 11:00–18:00
A technician arrives within 60 minutes anywhere in the city. Diagnostics are free.
Our own technicians4 to 20 years of experience




Repair prices
The symptoms customers report most often and their likely causes — the technician will check them during free diagnostics.
discharged battery, damaged propeller
from7 500 ₸
worn cells, oxidized contacts
from6 500 ₸
impact from a fall, broken ribbon cable
from4 000 ₸
worn bearing, broken winding
from7 500 ₸
interference, faulty antenna
from4 000 ₸
bent arms, chipped body
from7 000 ₸
worn mechanism, debris under the stick
from4 000 ₸
propeller settings are off
from4 500 ₸
The table lists the 'from' price for labor, for common jobs also the 'from' price of the part, plus the time required to complete the job.
1–2 hourstime
from 6 500 ₸cost

BeforeAfter5 steps

Five steps from request to checking the drone after the work.
Describe the model and symptoms — the technician will clarify the details and arrange a visit.
The technician comes anywhere in the city and inspects the drone on site.
The technician checks the body, arms, propellers, and power to assess the drone's condition.
The technician tests the drone and remote, and shows the customer the result after repair.
The technician tests the drone and remote, and shows the result of the check after the work.
We reply during working hours
Describe your drone model and the symptoms — the technician will arrange a convenient visit time and name the parts needed.

Warranty question? Call us
+7 (778) 096 59 616 127 reviews of repairs at TECH SERVICE in total
Василий Е.Order No. 57801 · 18 May 2026
oursПереезжали в новую квартиру, техника после перевозки захандрила. Привёз на диагностику: дрон. Проблема ровно одна: не держит высоту. Внутри оказалось: плата. Все функции проверил — работают.
Василий Е.Order No. 2603-1457 · 26 January 2026
oursВыбирал между официальным и этим, выбрал этот. Приехал с дачи, а тут — разбит при крушении. Сейчас пашет без нареканий!!
Эдуард К.Order No. AS-7121 · 29 April 2025
oursЖалоба одна: отказал мотор. Дамир М сам позвонил и сказал, что готово. Вернули — проверил, всё ок
Геннадий Ж.Order No. AS-5474 · 22 March 2025
oursЖалоба одна: разбит при крушении. Максим Снегирев разобрался в редкой модели. Проверил на всех режимах — держит)
Инна Н.Order No. AST-2410-936 · 26 November 2024
oursРаньше обращался в другой сервис, там очередь на две недели. Проверил всё, что мог: не держит высоту. Дамир М не пропал после ремонта, помог с настройкой. Сравнивал — здесь дешевле. Перезвонили на следующий день, уточнили детали. По факту меняли: плата. Прошивка та же, ничего не сбросили
Семён Ш.Order No. 2402-2932 · 7 May 2024
oursПроблема ровно одна: отказал мотор. Дамир М провозился, но сделал. Ни разу не пожалел.
Эдуард К.Order No. 85339 · 21 February 2023
oursТехника на балансе ТОО, нужен был чек и акт. Привёз на диагностику: дрон. Больше всего мешало: отказал мотор. Сказали, что позвонят, и действительно позванили. Внутри оказалось: плата. Отдал 31 000 и не жалею. Ни разу не пожалел
Василий Е.Order No. 71245 · 29 December 2021
oursДамир М отсоветовал дорогой ремонт, предложил простой. Позвонил, объяснил, сказали подъезжать — примут без записи. Ни шума, ни запаха, всё штатно.
Ульяна Ч.Order No. AS-6528 · 10 November 2021
oursПервое, что заметил: разбит при крушении. Дамир М разрулил всё быстро. Тихо, ровно, без сюрпризов.
Наталия С.Order No. 49948 · 27 September 2021
oursДамир М сам позвонил и сказал, что готово. Нашёл Tech-service в Астане по отзывам. Настройки не слетели, всё как было.
Семён Ш.Order No. ZK-2021-103 · 23 September 2021
oursМаксим Снегирев разобрался в редкой модели. Мастер сам предложил забрать технику на следующий день. Настройки не слетели, всё как было
Галина Ф.Order No. AS-1606 · 9 April 2021
oursЗимой без техники никак, поэтому тянуть было нельзя. Думал, показалось, ан нет: отказал мотор. Привезли на такси, приняли без вопросов. Пришлось ставить: мотор. Цену держали до конца, молодцы. Ставлю пять. Функционирует, тьфу-тьфу)
Вера Э.Order No. ZK-2021-663 · 21 January 2021
oursЗнакомый мастер раньше здесь работал, дал номер. Причина обращения — не держит высоту. Ни шума, ни запаха, всё штатно.
Людмила Щ.Order No. 10269 · 2 December 2020
oursС левого берега ехать далеко, поэтому искал поближе к дому. Приехал с дачи, а тут — отказал мотор. Ответили в мессенджере, потом созвонились. Обошлось заменой: камера. За такую работу 11 500 — адекватно. Доволен, если коротко. Работает, как будто и не ломалось.
Бауыржан Е.Order No. 2012-8715 · 18 September 2020
oursҚұрылғы ескі, бірақ жақсы қарайды екен. Бөлшек қоймада бар екен, күтпедік. Бәрі жақсы болды
Константин О.Order No. 32264 · 23 April 2020
oursОфис на Кабанбай батыра, технику туда и повёз. С этим и пришёл: не держит высоту. Ребята из techservice сидят в Астане давно. Внешне не видно, что разбирали
Наталия С.Order No. AST-1908-390 · 12 October 2019
oursВыбирал между официальным и этим, выбрал этот. Проверил всё, что мог: разбит при крушении. Все функции проверил — работают.
Аркадий Я.Order No. AST-1912-477 · 23 June 2019
oursЗаявку оставил через сайт вечером, утром перезвонили. Жалоба одна: разбит при крушении. Пользуюсь и вспоминаю добрым словом.
Валерия А.Order No. AST-1811-302 · 25 September 2018
oursЗаявку оставил через сайт вечером, утром перезвонили. Первое, что заметил: разбит при крушении. Вернули — проверил, всё ок.
Оксана Т.Order No. ZK-2018-394 · 1 September 2018
oursПозвонил в четыре места, тут ответили по-человечески. Проверил всё, что мог: разбит при крушении. Позвонил, объяснил, сказали подъезжать — примут без записи. Смета — 9 500, чек дали. По факту меняли: мотор. Проверил на всех режимах — держит.
experience7 yearsPC and network repair engineer
experience11 yearsSenior mobile computer technician
experience10 yearsLaptop repair technician
experience9 yearsMotherboard repair technician
experience16 yearsPrinter repair technician
experience12 yearsComputer repair technician
experience18 yearsAll-in-one computer repair technician
Didn’t find the answer? Message us on WhatsApp.
Ask a questionYes, most damage after a fall can be fixed, but a lot depends on the model and the force of impact. During free diagnostics, the technician will determine what's damaged — the body, gimbal, motors, or electronics — and suggest a repair.
Remove the battery immediately and don't try to turn the drone on — that's the main thing. Then take it to a service center: there's a chance to save the board and motors if you don't power up wet electronics.
Yes, we work not only with DJI but also with other brands — Autel, Xiaomi, FIMI, and others. The available services depend on the model, which is clarified during free diagnostics.
Search using the last point from the app and flight logs, and show the found drone to a technician. After a fall or water exposure, it needs diagnostics: an intact body doesn't guarantee working electronics.
Yes, a technician comes to your home anywhere in the city within 60 minutes and inspects the drone on site. Some work is done right away, while complex cases require repair at the service center — this will be determined after free diagnostics.
Yes, after replacing a motor, gimbal, or repairing the body, calibration of the IMU, compass, and gimbal is usually required. The technician performs it before a test flight so the drone flies steadily again.
Tech Service repairs drones in Astana as a direct provider: our technician arrives at your door within 60 minutes anywhere in the city or accepts the drone at our service center. Diagnostics are free, we provide a 1-year warranty on labor and parts, and the technician gives you the price after diagnostics. We fix DJI Mini, Air, Mavic, Phantom, Matrice, as well as Autel, Xiaomi, and FIMI.
Most requests start with a symptom, not a part name: the drone won't turn on, won't take off, or behaves unpredictably. We break down common symptoms, likely causes, and what you can safely check before the technician arrives.
Most often, a fall damages ribbon cables, connectors, and the power board rather than the battery itself. The impact hits the frame, and the body absorbs the energy, but internal connections shift: the power connector comes loose from the board, the camera ribbon rubs against an edge, the battery connector loses contact. Externally, the device looks intact—no cracks, no chips—so the owner first replaces the battery, even though the issue is in the power circuit. Troubleshooting starts with testing connectors and inspecting the board under magnification, not with replacing parts at random. A separate trap is a cracked solder joint on the power board: under load the contact disappears, but at rest the multimeter shows normal. Before the technician arrives, don't disassemble the body or wiggle the board—you might damage ribbon cables that are still intact.
In our experience, the cause is most often the motor, ESC, or firmware, and by the sound at startup the technician already narrows it down. A brushless motor loses balance or seizes a bearing after an impact, the ESC—the speed controller—fails due to overheating or a voltage spike, and a mismatch between the drone and remote firmware blocks startup entirely. Diagnostics are free: the technician listens to how the props spin up, checks each controller channel, and compares software versions. A bearing clogged with sand also causes a jolt at start, but you hear it as a dry grinding, not silence. If one motor heats up more than the others after a short run, that's a signal to check the ESC, not to replace the motor blindly. During free diagnostics, the technician compares readings on each channel and confirms the cause before disassembling the body.
Drifting is usually related to the IMU or compass, loss of connection to the GPS module or remote, and shaking to the gimbal. The gyroscope and accelerometer in the IMU module accumulate error after a hard landing, the compass gets thrown off by metal objects nearby during calibration, the GPS antenna cracks at the base, and the gimbal stabilizer loses smoothness due to play in the axes or a stretched camera ribbon. Symptoms rarely come alone: loss of connection and drifting often point to the same board. Shaking in the footage during level flight indicates a worn motor bearing, not the gimbal—check if there's ripple in the video in calm weather. Before going to the service center, try recalibrating the compass in an open area—if the drift remains, it's not a setting but hardware.
Not every breakdown is reasonable to fix on-site. We explain where the specialist works on location, where a workshop is needed, and how free diagnostics work before restoring drones in Astana.
Motor replacement, board soldering, frame restoration, and full body disassembly are done at our service center because they require stationary tools and a level work surface. We won't open the main board in the field while it's hanging: the risk of touching adjacent traces and ribbons is too high, and soldering in the air almost always comes back with a repeat failure after a couple of flights. If the inspection shows that motor replacement or frame restoration is needed, the device is taken to the workshop, where it is disassembled, each component is diagnosed, and only then do we start soldering. This approach saves money: the client doesn't pay twice for the same breakdown. In our practice, soldering and the frame are the jobs most often attempted at home and then redone. That's why we determine right from the symptoms whether the drone can be fixed on-site or at the service center. Drone repair in Astana at the workshop involves full disassembly and checking each component before soldering.
Owners often don't know if their model will be accepted for service. Below are the lines and brands we work with, and what breaks most often in each.
| Line | What breaks most often | What we check |
|---|---|---|
| Mini | propellers, landing gear, arms | motors, board, camera |
| Air | gimbal, ribbons | gyroscope, mounts |
| Mavic | gimbal, lens | camera, ribbon |
| Phantom | body, motors | mounting points, board |
| Matrice | motors, boards | load, power circuits |
| Inspire | gimbal, landing gear | drives, mounts |
We service not only DJI but also Autel, Xiaomi, and FIMI, and diagnostics for them follows the same scheme — inspecting the body, motors, gimbal, and electronics. Non-DJI models are trickier with firmware and remote pairing: manufacturers release updates less often, and some components take longer to source. So the technician immediately says what can realistically be done and where restoration is limited by parts availability. During free diagnostics, we check the board, motors, and camera and explain which components can be restored and which will have to be replaced. We also check the firmware version and the condition of the battery compartment — on these brands, they often fail after the wet season. In my opinion, it's useful for the owner to specify the model and firmware version in advance — this speeds up finding a solution and reduces the number of times the body needs to be opened.
We service the remote controller, camera, and gimbal as separate units, even if the drone itself is working fine. The remote controller may stop detecting the aircraft after an update or a drop—then we check the board, sticks, and communication module. Cameras and lenses suffer from impacts: cracks appear, focus is lost, and recording shows stripes. The stabilizer loses smoothness due to a bent ribbon cable or play in the drives, and after a hard contact with the ground, tilt angles get misaligned. If the remote controller doesn't detect the aircraft after an update, the issue is often not the controller itself but firmware desynchronization—the technician handles pairing and updating. In our experience, it's more cost-effective to repair such units separately than to replace the whole set: restoring one remote controller costs less than replacing the pair.
Fast discharge and a swollen case are common reasons for contacting a service center. We explain why a drone loses charge and in which cases the battery can be restored, and when a new one is required.
Fast discharge is usually caused by cell degradation, battery controller failure, or cold rather than the drone itself. Lithium-polymer cells lose capacity with each charge cycle, and even faster when stored discharged. The controller balances voltage between cells: if it fails, one cell drains earlier than the others and the device sharply loses thrust. In winter, at sub-zero temperatures, capacity drops noticeably due to increased internal resistance—that's chemistry, not a malfunction. Chargers and hubs with damaged cables or connectors also provide incomplete charging, and flight time decreases. If cells discharge unevenly, using such a battery is risky—the drone may shut down mid-flight.
| Symptom | What we do | Why |
|---|---|---|
| Swollen case | Install a new battery | Deformed cells are not restored |
| One cell is more discharged | Check the controller, replace it | Imbalance leads to shutdown mid-flight |
| Heating during charging | Diagnostics and replacement | A sign of internal short circuit |
| Doesn't hold charge after storage | Capacity test, then replacement | Deep discharge irreversibly reduces capacity |
| Damaged connector or contact | Replace the connector | Poor contact causes incomplete charging |
We can restore a battery if the problem is in the controller or contacts, not the cells themselves. The controller is a separate board that monitors the voltage of each cell and cuts power on overload; replacing it brings the battery back to working condition without replacing cells. Oxidized or burnt connector contacts and a faulty hub can also create a false impression of a "dead" battery: the drone doesn't see the charge or charges partially. The technician first checks power during diagnostics—sometimes a "dead" battery turns out to be fine, and the connector or charging hub is to blame. Diagnostics are free, and based on the results the technician provides the cost of work. If the cells themselves have degraded, restoration won't help—a new battery will be required.
Replacing parts changes the device's factory parameters, so it needs to be reconfigured before handover. Here's what calibrations and checks we perform before returning the equipment to the owner.
After service, we calibrate the IMU, compass, and gimbal because replaced components change the device's settings. The inertial measurement unit is responsible for orientation in space, the compass for heading, and the stabilizer for a level camera horizon. IMU calibration is performed on a flat surface in several body positions: the technician sequentially turns the device over and locks each position. The compass is checked away from metal and sources of magnetic interference — rebar, transformers, large speakers. The gimbal is adjusted along the tilt and roll axes, and then smoothness of movement is checked at the extreme positions. In my experience, it's the IMU that most often gets knocked off when replacing the frame or motors — without re-calibration, the device tilts right at takeoff. This procedure is not a formality: without it, the quadcopter drifts to the side or shoots with shaking even with new parts.
We update the drone and controller firmware and re-pair the controller so the connection works reliably. Replacing the board, camera, or transmission module changes the identifiers that the controller checks when connecting. First, we check the current software versions on the device and the controller, then update both to matching builds, and then pair the controller with the quadcopter. Version mismatch is a common reason why the equipment doesn't see the controller or loses the channel at distance. We also check the stick and mode switch ranges — after replacing the board, they may deviate from factory values and require re-adjustment. If the controller doesn't see the drone after the update, don't roll back the firmware manually — version mismatch is resolved by pairing with a technician.
Before handover, we check the quadcopter with a test flight to make sure it maintains connection and hovers steadily. We look at the response to sticks, motor operation at different speeds, altitude hold, and compass reaction when turning. We also check IMU telemetry and sensor readings — whether there are angle jumps or axis errors. We run the device in different modes: climb, hover, turn, straight-line flight — this is how vibrations and drift that aren't visible on the bench show up. A test flight reveals what's not visible on the bench: motor vibration or compass drift that only appears in the air. For residents of the capital, this control is important — windy conditions quickly show whether the device holds its heading. And only after stable hovering and a level picture do we hand the equipment back to the owner.
Before contacting us, it's important to understand what you get beyond the repair itself. We explain the warranty, free diagnostics, payment, and how our specialists work.
We provide a 1-year warranty on labor and parts, and this applies to both on-site visits and in-service repairs. During this period, any repeat failure caused by us is re-examined from scratch, not blamed on natural wear and tear. The condition applies to both replaced parts and the procedure itself — from board soldering to motor or gimbal replacement. A warranty only makes sense together with diagnostics: if the cause isn't confirmed, replacing a part doesn't solve the problem, and this becomes clear during the test flight. That's why we don't replace components "just in case" — first we find the source of the failure, then we fix it. In my view, a year is enough time for both the quality of the part and the care of assembly to show. The owner should keep the description of the work performed: it makes it easier to prove that the failure is a warranty case.
Tech Service is the direct provider: a technician either comes to you or takes the drone in at the service center, with no middlemen involved. The field technician and the in-shop technician are the same people with 4 to 20 years of experience, not a separate intake desk. The drone doesn't get passed from hand to hand: whoever opens it up is the one who sees the job through to a test flight. When the same person who diagnosed the device does the repair, the cause and the result don't drift apart — you can tell because the fault is explained before the work, not after. Within the city, arrival takes up to 60 minutes. In our experience, this setup is easier on the owner: no need to describe the symptoms twice or wonder who's responsible for the result.
We accept payment via Kaspi QR, Kaspi Red (instalments), bank card, cash, or bank transfer for companies, and the technician quotes the price after free diagnostics. With a single symptom — "won't turn on" or "overheating" — it's impossible to give an honest estimate: the same behavior can come from the power board, the motor, or the firmware. Teardown shows what actually needs replacing and what just needs calibration or re-soldering. This approach protects you from surprises: you approve the work with a clear cause and scope, not a guess made over the phone. Diagnostics are free whether or not you choose us for the repair. Pricing after diagnostics also helps rule out unnecessary replacements: if a part is fine, it stays. You pay however is convenient for you, and the final amount is fixed before work begins.
Diagnosing drone faults comes down to a short set of takeaways — from diagnostics to post-repair checks. Here's what to keep in mind before handing your device to a technician.
7brands
We source parts and carry out repairs for the models that have dedicated pages on the site.
Tech Service technicians repair other appliances too — with the same 1-year warranty on labour and parts.
Refrigerator Repair in Almatyfrom 3 000 ₸
Washing Machine Repair in Almatyfrom 3 000 ₸
Dishwasher Repair in Almatyfrom 3 500 ₸
Oven Repair in Almatyfrom 3 000 ₸
Cooktop Repair in Almatyfrom 3 500 ₸
Air Conditioner Repair in Almatyfrom 3 500 ₸
Boiler and Water Heater Repair in Almatyfrom 2 500 ₸
Freezer Repair in Almatyfrom 6 000 ₸
Tumble Dryer Repair in Almatyfrom 5 000 ₸
Coffee Machine Repair in Almatyfrom 2 500 ₸
Robot Vacuum Cleaner Repair in Almatyfrom 3 500 ₸
Vacuum Cleaner Repair in Almatyfrom 1 500 ₸
Microwave Oven Repair in Almatyfrom 2 000 ₸
Hair Dryer Repair in Almatyfrom 1 500 ₸
Iron Repair in Almatyfrom 3 000 ₸
Electric Kettle Repair in Almatyfrom 2 500 ₸
Mixer Repair in Almatyfrom 2 500 ₸
Multicooker Repair in Almatyfrom 500 ₸
If your laptop screen is broken, turn the device off first, don't press on the display, and check the picture through an external monitor.
12 March 2026 · 11 minutes read
If your laptop freezes, the first thing to do is restart it and check Task Manager to see what's loading the CPU and memory.
25 January 2026 · 12 minutes read
If your computer won't turn on, start simple: check the outlet, power cable, switch on the power supply, and the power button.
19 January 2026 · 13 minutes read
If your laptop won't boot, first determine which of two states you're in: the device doesn't respond to the power button at all…
13 December 2025 · 12 minutes read












