Ангелина Я.Order No. 50581 · 12 January 2025
oursПозвонили из сервиса сами, напомнили о записи. Выбрал techservice, потому что близко к работе. Обращусь снова, если понадобится.
City
Language
What broke
Sections
Message on WhatsApp+7 (778) 046 88 53Mon–Fri 10:00–19:00, Sat–Sun 11:00–18:00
Your magnetic exercise bike runs like new again. 1-year warranty on labor and parts.
Our own technicians4 to 20 years of experience




Repair prices
Below are typical symptoms and their likely causes; the technician confirms the exact cause after free diagnostics.
no power, damaged cable
from5 500 ₸
belt slipping, pulley wear
from4 000 ₸
loose fasteners, worn bearing or belt
from4 000 ₸
sensor failure, broken wire
from4 500 ₸
tension mechanism jammed
from5 500 ₸
belt too tight, worn shaft bearings
from5 000 ₸
loose frame bolts, uneven floor
from5 500 ₸
worn bearing, belt, or bushing
from4 000 ₸
The table lists the 'from' price for labor, for common jobs also the 'from' price of the part, plus the time required to complete the job.
1–2 hourstime
from 5 000 ₸cost

BeforeAfter5 steps

Five steps from request to checking the bike's operation.
Describe the symptom and the bike model so the technician brings the right tools.
The technician confirms a convenient visit window and checks that the bike is easily accessible.
The technician confirms the model and symptom details to prepare tools and common parts in advance.
Work starts after you agree on the scope and cost.
The technician shows how the bike works after repair and explains what changed in the unit's behavior.
We reply during working hours
Send the model and symptom in your request — get the technician's advice on the cause before the visit. Ask which parts will be needed and how payment works.

Warranty question? Call us
+7 (778) 046 88 536 127 reviews of repairs at TECH SERVICE in total
Ангелина Я.Order No. 50581 · 12 January 2025
oursПозвонили из сервиса сами, напомнили о записи. Выбрал techservice, потому что близко к работе. Обращусь снова, если понадобится.
Елизавета Л.Order No. 27047 · 11 December 2023
oursПервый раз обратился, до этого чинился у знакомого. Было важно успеть до конца недели, а то морозы обещали. Функционирует, тьфу-тьфу.
Жулдыз М.Order No. 2206-8748 · 25 September 2022
oursПриехал по записи, всё было готово к моему приходу. Вернули — проверил, всё ок.
Рая И.Order No. ZK-2020-446 · 5 December 2020
oursСервис выбрал по карте — этот был ближе всего. Выбирал между официальным и этим, выбрал этот. Сначала назвали одну сумму, потом уточнили. Могу советовать
Иван Н.Order No. 27821 · 22 February 2020
oursСервис выбрал по карте — этот был ближе всего. Выдали квитанцию и гарантийный талон. Сделали то, что обещали, и ничего лишнего. Позвонили, когда можно забирать. Не пришлось ездить дважды. Назвали сумму заранее, в конце она не поменялась. Работу закончили раньше срока. Для Астаны — хороший вариант.
Ярослав С.Order No. AS-9350 · 23 January 2020
oursПервый раз обратился, до этого чинился у знакомого. Радик Т провозился, но сделал.
Семён Ш.Order No. 74236 · 20 December 2019
oursПервый раз обратился, до этого чинился у знакомого. Могу советовать. Всё проверили при выдаче.
Валерия А.Order No. 68233 · 2 October 2019
oursПозвонили из сервиса сами, напомнили о записи. Было важно успеть до конца недели, а то морозы обещали. Турарбек Кайрош разобрался в редкой модели. Сделали так, что и не придерёшься
Ангелина Я.Order No. 11888 · 14 June 2019
oursПриехал по записи, всё было готово к моему приходу. Дамир М разрулил всё быстро. Работу закончили раньше срока. Мастер посмотрел при мне, объяснил, что случилось. Всё проверили при выдаче. Объяснили, как продлить срок службы. Сделали так, что и не придерёшься.
Акжол Э.Order No. ZK-2019-366 · 17 April 2019
oursПриехал по записи, всё было готово к моему приходу. Не идеально, но по-честному.
experience14 yearsSenior small appliance technician
experience15 yearsOn-site coffee machine diagnostics technician
experience5 yearsCoffee machine cleaning technician
experience12 yearsCoffee machine diagnostics technician
experience5 yearsPortafilter coffee machine technician
experience12 yearsVacuum cleaner repair technician
experience15 yearsVacuum cleaner repair technician
experience18 yearsWashing machine repair technician
Didn’t find the answer? Message us on WhatsApp.
Ask a questionIt depends on the model and the nature of the fault: sometimes the technician only needs to replace a burned-out component or restore the board contacts. If the board is flooded or badly burned, it is replaced entirely. The exact option is determined by free diagnostics.
Yes, we take on not only home but also professional exercise bikes from clubs and gyms. A technician travels to the site anywhere in the city and works with the magnetic system, mechanics, and electronics. Repair at the service center is also possible.
Play gradually wears out the seating surfaces and bearings, so a minor knock turns into replacement of components. Training on a loose frame is also unsafe. It's better to show the bike to a technician before the fault becomes major.
Most faults are fixed by the technician right at your home: they disassemble the component and replace the belt, bearings, or sensors on site. The bike is taken to the service center only if complex board soldering or a rare part is needed. On-site diagnostics are free.
Most often the cable or the magnet rotation mechanism is to blame, less often the servo drive and control board. It depends on the model: on some, resistance is changed by a knob, on others by a small motor commanded from the console. The technician will determine what exactly has failed.
Yes, the work performed and installed parts are covered by a 1-year warranty. If the fault reappears, the technician will address it under warranty. This applies to both at-home and service center repairs.
Tech Service repairs magnetic exercise bikes in Astana: our technician comes to your home or you can bring the bike to our service center. Diagnostics are free, and you get a 1-year warranty on labor and parts. The technician arrives within 60 minutes anywhere in the city, and you'll get a quote after the free diagnostics.
Resistance doesn't just disappear on its own—it's usually one of the magnetic system components or the drive. Let's break down what creates resistance and how to check it.
Resistance in a magnetic exercise bike is created by a row of permanent magnets that moves closer to the spinning flywheel and brakes it with a magnetic field. The position of the magnet bar is controlled by a servo drive connected to the handle or console buttons via a cable and gearbox. In a mechanical exercise bike, resistance comes from friction pads or belt tension, so the pads wear out, not the magnets. The gap between the magnets and the flywheel is the key parameter: as it increases, the field weakens, and your workout feels like it's 'spinning freely.' The smaller the gap, the higher the resistance—so even a slight shift of the bar or a loose cable can feel like 'lost resistance.' Before disassembling the unit, check whether the magnet bar reaches its extreme position when you turn the handle to max—this helps distinguish a mechanical issue from an electronic one.
In our diagnostics, the most common culprits are the servo drive, tension cable, or a misadjusted magnet-flywheel gap—we check the belt as a second step. The servo drive moves the magnet bar to change resistance levels, and when its gears wear out, it stops positioning the bar correctly. The tension cable stretches over time, the magnet drive gearbox can jam, and the handle turns without response. We check the drive belt and pulley when the flywheel isn't connected to the pedals. If the pedals spin easily but the flywheel turns with resistance, the problem is in the magnetic part; if the flywheel is also free, we look at the drive belt and pulley. A Tech Service technician arrives at your home anywhere in the city within 60 minutes, and diagnostics are free—afterward, they'll tell you the cause and the cost of the work.
In a magnetic bike, we restore the electromechanical resistance system, while in a mechanical one we service the pad or belt brake. The magnetic unit requires different diagnostics: we check the bar movement, the condition of the servo drive and gearbox, the position sensor of the magnets, and the response at each level. In a mechanical bike, the friction pads and tension spring wear out—so the work is limited to replacing consumables and adjusting. The magnetic system is sensitive to sensor position and gap, so after replacing components, we always test resistance at all levels, not just the first one. We provide a 1-year warranty on labor and parts, and our technicians have 4 to 20 years of experience. You can pay via Kaspi QR, Kaspi Red, bank card, cash, or bank transfer for companies, including cards and cash.
Unusual noises are the most accurate indicator of a worn component. Let's break down what each sound means and when repair can't wait.
| Noise | Likely component | When it appears |
|---|---|---|
| Crunching | Bottom bracket or crank arms | Under load |
| Rustling and tapping | Flywheel | During rotation |
| Squeaking and play in the arms | Sliding bushings | At idle |
| Clicking | Gearbox, magnet cable | When changing levels |
Squeaks and wobbling are most often caused by worn slide bushings and loose crank arms — we check these first. The bushings sit in the pedal arm joints and in the handlebar mount: as wear increases, play appears, metal rubs against metal, and you hear a steady squeak at idle. A loose crank arm on the bottom bracket axle gives a different sound — a rhythmic knocking synchronized with pedal rotation. If wobbling appears suddenly after a high-load workout, it's worth checking not only the bushings but also how the crank arms sit on the axle — play there quickly damages the seat, and then simple tightening no longer helps. Worn flywheel bearings add a rustling or dull knocking to the picture. During diagnostics, we spin the parts one by one and find the source of the noise instead of replacing parts at random.
Some squeaks go away after lubrication and adjustment, but crunching and knocking almost always mean wear that requires part replacement. Lubrication and servicing help when the bushings are still intact and the sound comes from dry friction or a loose mount: the technician cleans the seats, applies lubricant, and sets the clearances. Crunching when pedaling points to bottom bracket bearings, rustling in the flywheel points to its bearings, and here lubrication only gives a temporary effect. Repair in such cases includes replacing worn parts and adjusting the magnet gap so the load is distributed evenly. Putting off work when there's crunching is risky — a worn bearing starts hitting the axle and gradually damages neighboring parts, and the scope of work grows. Our technicians at free diagnostics disassemble the unit and show what exactly needs replacement and what just needs servicing.
The electronics of an exercise bike control both the load and the console. We explain what's behind a failure to turn on and a code on the screen, and when the unit can be restored.
Most often the cause is power, connectors, and wiring, not the control unit itself — so diagnostics start with the power circuit. First check the adapter: on magnetic models it's external, 6 or 9 volts, and if the cable is bent at the plug, voltage drops. Then inspect the power socket on the housing — it loosens from constant plugging, and the contact becomes unstable. Inside, check the ribbon cable from the console to the control unit: oxidized or shifted connectors give exactly the same symptom as a burnt board. If the bike doesn't respond to buttons but the console lights up, the problem is usually in the ribbon cable or console connector, not the load controller. Before opening the housing, test the adapter with a multimeter — that way you eliminate half of false calls before the technician arrives.
An error code is the controller's signal about a specific part or sensor, not a verdict on the whole bike, and its meaning depends on the model. The console receives data from the magnet position sensor, reads pedal speed and motor current, and when any parameter goes out of range, displays an alphanumeric combination. For some manufacturers, E1 means loss of communication with the sensor; for others, the same combination indicates drive overload. The magnet position sensor shifts over time, gets contaminated with metal dust, and the controller stops seeing the load flap position. The same code from different manufacturers can point to different parts, so it's not worth replacing parts at random based on the code without checking the unit. Write down the combination from the screen and the bike model — with this pair, the technician will prepare the needed part before the visit.
We start by diagnosing the control board component by component, and often we can restore it without a full replacement — we only replace the failed element. Diagnostics are free: the technician opens the casing, checks the power at the board input, tests the traces, checks the magnet position sensor, and inspects the connectors and wiring. A sensor fault, a broken ribbon cable, or a burnt contact can be fixed locally without replacing the board. A burnt-out power section or a cracked trace under the chip is a case where the board is replaced entirely; otherwise it will fail again. We provide a 1-year warranty on labor and parts. The decision to repair or replace depends on which element failed: a sensor or connector fault can be fixed locally, while a burnt board requires a new unit. Ask the technician which elements they checked and which one they are replacing — that way you can see that a component is being restored, not the whole machine.
The job starts with free diagnostics and ends with a load test. We break down each step so you know what to expect from the technician's visit.
We provide free diagnostics, and the technician comes to your home within 60 minutes anywhere in the city — you don't need to bring the machine to the service center. On site, the specialist checks the load system, inspects the flywheel, belt, and control board, and listens to the components while pedaling. The inspection is free precisely because without it you can't name the cause: the same symptom can come from a stretched belt, incorrect gap between the disc and magnets, or a sensor fault. The specialist identifies the specific component, so the next step is repairing one part, not the whole machine. They quote the cost after the inspection, once the cause is clear. In my experience, mechanical faults are found fastest — you can see and hear them right away, while electronics take longer to check.
At your home we do adjustments, replace accessible components, and test the load, while complex control board work is done at the service center. We handle mechanical issues on site: tighten fasteners, set the gap between the disc and magnets, replace the belt, pedals, and crank bearings. Electronics require a different approach — the control board is easier to test on a bench where you can see how all levels behave. The choice between at-home and in-service depends on the component: if the machine won't turn on or shows an error code, the specialist first rules out the simple things — power and contacts — and then takes the board. In our practice, most calls are resolved on site because the majority of breakdowns are mechanical. Before the visit, the technician clarifies the symptom over the phone so they bring the right parts and save you a second trip.
The main fear when hiring a service is paying and then facing the same breakdown again. We explain what the warranty covers and why it matters who does the work.
We give a 1-year warranty on labor and parts — if the unit fails again after service, we'll fix it under warranty. The term applies to both areas at once: the quality of installation and the part itself that was installed in the machine. In practice, breakdowns fall into two groups — some are due to installation errors, others to the component's lifespan, and the same period covers both. The condition is simple: any independent tampering with the repaired unit voids the warranty, so don't go adjusting what's already been done. Magnetic exercise bike repair most often involves bearings, the belt, and the sensor — for each of these units, the parts warranty works separately from the installation warranty, and that's convenient: if the part itself fails, it will be replaced under warranty, not at the owner's expense. The parts warranty being separate from labor is important because some breakdowns are due to the quality of the part, not the installation.
Restoration is usually justified when one unit has failed but the frame and flywheel are intact — then replacing the part gets the machine working again. The magnetic system on these models is repairable: the bearing, belt, sensor, or control board can be replaced, while the housing and flywheel keep serving. The process includes replacing worn components and adjusting the magnet gap — after that, resistance is set by levels again as the manufacturer intended, and pedaling brings back the usual smoothness. It's a different story when a crack has developed in the load-bearing structure or the flywheel is deformed: restoring the geometry here is not advisable, since the load on the frame during training is constant and any fix won't last long. Buying a new exercise machine makes sense when the load-bearing structure is damaged or the work affects several expensive components at once. In other cases, replacing one part is noticeably less hassle than moving and assembling a new machine.
Tech Service is a direct contractor: the work is done by our own technician with 4 to 20 years of experience, not a middleman or an aggregator. Our specialist comes to your home anywhere in the city, diagnoses the problem himself, and is responsible for the result. We don't have a chain of subcontractors where one takes the request, another delivers the part, and a third installs it — each pointing at the previous one. When a direct contractor handles the job, responsibility for the work and parts isn't diluted among subcontractors, and the warranty is honored in practice. In my view, that's the main argument for a direct technician: there's someone to hold accountable for the result, and the service history isn't lost when passed from one link to another.
Some checks can be done before the specialist arrives so you don't pay for the obvious. Here's how to inspect it yourself and prepare for the visit.
After a long period of disuse, the bearings, belt, and lubrication are usually the first to suffer — equipment needs servicing before it's started up again. The drive belt transfers rotation from the pedals to the flywheel, and over years of standing still it loses tension, while the grease in the flywheel bearings thickens and gets pushed out of the friction zones. The first start without preparation puts stress on worn components: the belt slips at high resistance levels, the flywheel moves jerkily, and a humming noise appears. Our technician on site checks belt tension, bearing condition, and lubrication, not just the obvious fault. We also inspect the connecting rod seats and pedal mounts: during inactivity, the metal in them corrodes, and the first intense workout strips the threads. Before the first workout, it's worth checking belt tension and bearing condition, otherwise the load on worn components will increase sharply.
The technician quotes the price after a free diagnostic, once it's clear which component has failed and what work is needed. Diagnostics are free, and a specialist arrives within 60 minutes anywhere in the city, so the assessment isn't delayed for days. We accept Kaspi QR, Kaspi Red, card, cash or bank transfer and provide a 1-year warranty on labor and parts. An accurate estimate before diagnostics is impossible because the same symptom on different models points to different components and different amounts of work: lost resistance can be due to the belt, the magnetic system, or the sensor. That's why cost and timeline are discussed after the inspection, not over the phone. Home servicing of exercise equipment with a warranty in Astana is convenient because the specialist comes to you, rather than you taking the machine to a service center.
Here are the key things to keep in mind when your exercise machine stops working as it used to: what determines the cause of the breakdown and what to look for when choosing a technician.
17brands
We repair exercise bikes from common brands — find yours in the list.
Tech Service technicians repair other appliances too — with the same 1-year warranty on labour and parts.
Refrigerator Repair in Almatyfrom 3 000 ₸
Washing Machine Repair in Almatyfrom 3 000 ₸
Dishwasher Repair in Almatyfrom 3 500 ₸
Oven Repair in Almatyfrom 3 000 ₸
Cooktop Repair in Almatyfrom 3 500 ₸
Air Conditioner Repair in Almatyfrom 3 500 ₸
Boiler and Water Heater Repair in Almatyfrom 2 500 ₸
Freezer Repair in Almatyfrom 6 000 ₸
Tumble Dryer Repair in Almatyfrom 5 000 ₸
Coffee Machine Repair in Almatyfrom 2 500 ₸
Robot Vacuum Cleaner Repair in Almatyfrom 3 500 ₸
Vacuum Cleaner Repair in Almatyfrom 1 500 ₸
Microwave Oven Repair in Almatyfrom 2 000 ₸
Hair Dryer Repair in Almatyfrom 1 500 ₸
Iron Repair in Almatyfrom 3 000 ₸
Electric Kettle Repair in Almatyfrom 2 500 ₸
Mixer Repair in Almatyfrom 2 500 ₸
Multicooker Repair in Almatyfrom 500 ₸
If your dishwasher won't drain, the most common culprits are a clogged filter or drain hose; less often, it's the pump, impeller…
24 March 2026 · 12 minutes read
A washing machine can hum for many reasons, and the first thing to figure out is when the sound appears.
20 March 2026 · 12 minutes read
The easiest way to remove scale from a kettle is with citric acid: 1–2 tablespoons per liter of water, boil for 5–10 minutes, then drain and rinse.
17 March 2026 · 13 minutes read
If your laptop screen is broken, turn the device off first, don't press on the display, and check the picture through an external monitor.
12 March 2026 · 11 minutes read
Air conditioner errors are codes on the display or flashing indicators that show which component has failed.
5 March 2026 · 12 minutes read
If your washing machine isn't filling with water, the most common culprits are a closed valve, a clogged inlet filter screen on the hose…
20 February 2026 · 13 minutes read












