Open until 19:00+7 (778) 046 88 53Call a technician
Tech Service technician next to a power tool

Power Tool Repair in Astana

Free diagnostics, a technician arrives within 60 minutes anywhere in the city. 1-year warranty on labor and parts.

  • 1-year warranty on labor and parts
  • Technician arrives within 60 minutes anywhere in the city
  • Free diagnostics

Our own technicians4 to 20 years of experience

Kairat A.Ruslan S.Nikita O.Kuanysh A.

Repair prices

  • Diagnostics0 ₸
  • Power cord replacementfrom2 000 ₸
  • Bearing replacementfrom2 000 ₸
  • Battery pack repairfrom2 000 ₸
  • Cleaning and maintenancefrom2 000 ₸
All prices
ours5,06 127 reviews
order database
Common faultsCommon faultsTECH SERVICE02

Common power tool faults in Astana

Below are common symptoms and likely causes. The technician names the exact cause after free diagnostics.

PricesPricesTECH SERVICE03

How much power tool repair costs in Astana

The table lists the 'from' price for labor, for common jobs also the 'from' price of the part, plus the time required to complete the job.

Power cord replacementparts not included

1–2 hours

from2 000 ₸

Bearing replacementparts not included

1–2 days

from2 000 ₸

Battery pack repairparts not included

1–2 hours

from2 000 ₸

Cleaning and maintenanceexact price — after the free diagnostics

1–2 hours

from2 000 ₸

Carbon brush replacementparts not included

1–2 hours

from2 500 ₸

Before and afterBefore and afterTECH SERVICE04

Before and after power tool repair in Astana

Start button sticks

1–2 hourstime

from 3 000 ₸cost

Problem
The start button stuck and did not return to its original position, so the tool would not turn off.
What we did
The technician replaced the button assembly and checked that the key was secure.
Result
The tool turns on and off normally, and the key returns to its original position.
I want the same
An angle grinder lies on a mat on a workbench in a workshop, with a screwdriver nearby.BeforeAfter
01 / 03
All repairs
TECH SERVICE mobile technician with a tool case

How power tool repair works on site in Astana

Five steps from request to final check. Diagnostics are free.

  1. Requestsame day

    Describe the symptom and give the tool model — the technician will prepare for the visit.

  2. Technician visitwithin 60 minutes

    The technician comes anywhere in the city, inspects the tool, and records the working conditions.

  3. Diagnosticsfree

    The technician identifies the cause of the fault and agrees the scope of work with you before starting the repair.

  4. Work approvalbefore repair

    You receive a written list of work and approve the scope; only then does the technician start the repair.

  5. Old part returnafter repair

    The technician hands over the removed part so you can verify the replacement.

Leave a request
TechniciansTechniciansTECH SERVICE05

Our small appliance repair technicians in Astana

The small appliance repair department in Astana has 8 technicians with 5 to 18 years of experience.

  • 8 technicians in Astana
  • 5–18 years of experience in the department
  • Article author Kairat A., 14 years of experience
Mobile technician fixing a washing machine at the customer's home
Field technician at a customer’s home

The department has 7 specializations — they are listed on the technicians' cards.

01 / 08
Kairat A., senior small appliance technicianexperience14 years

Kairat A.

Senior small appliance technician

Ruslan S., on-site coffee machine diagnostics technicianexperience15 years

Ruslan S.

On-site coffee machine diagnostics technician

Nikita O., coffee machine cleaning technicianexperience5 years

Nikita O.

Coffee machine cleaning technician

Kuanysh A., coffee machine diagnostics technicianexperience12 years

Kuanysh A.

Coffee machine diagnostics technician

Aydar A., portafilter coffee machine technicianexperience5 years

Aydar A.

Portafilter coffee machine technician

Serikbay A., vacuum cleaner repair technicianexperience12 years

Serikbay A.

Vacuum cleaner repair technician

Artur G., vacuum cleaner repair technicianexperience15 years

Artur G.

Vacuum cleaner repair technician

Akzhol K., washing machine repair technicianexperience18 years

Akzhol K.

Washing machine repair technician

We reply during working hours

Book power tool repair in Astana

Leave a request — diagnostics are free. The technician will name the cause and the price. 1-year warranty on labor and parts.

TECH SERVICE administrator replying to a customer's WhatsApp message

Warranty question? Call us

+7 (778) 046 88 53
Customer reviewsReviewsTECH SERVICE06

Reviews of power tool repair in Astana

5,0ours

6 127 reviews of repairs at TECH SERVICE in total

Римма Х.Order No. 10190 · 21 May 2024

ours

Сервис выбрал по карте — этот был ближе всего. Мастер посмотрел при мне, объяснил, что случилось. Позвонили, когда можно забирать. В целом доволен.

Римма Х.Order No. ZK-2023-807 · 7 September 2023

ours

Зашёл узнать цену, в итоге оставил технику. Дамир М подобрал аналог дешевле, не навязывал оригинал.

Альбина Ю.Order No. AST-2010-641 · 21 December 2020

ours

Искал сервис, где дают гарантию и чек. Рекомендую, без пафоса. Не пришлось ездить дважды.

Альбина Ю.Order No. AST-2002-368 · 4 June 2020

ours

Обращаюсь сюда второй раз, впечатление не изменилось. Друг из Сарыарки посоветовал это место. Максим Снегирев разобрался в редкой модели. Оформили быстро, без анкет и лишних вопросов. Назвали сумму заранее, в конце она не поменялась. Рекомендую, без пафоса!!

Вера Э.Order No. AST-1803-382 · 24 September 2018

ours

Позвонили из сервиса сами, напомнили о записи. Объяснили, как продлить срок службы. Приняли технику в конце дня, не отправили домой. Оформили быстро, без анкет и лишних вопросов. Назвали сумму заранее, в конце она не поменялась. Общение спокойное, без навязывания. Не пришлось ездить дважды. Работу закончили раньше срока. После ремонта — как новое.

Геннадий Ж.Order No. 1807-2010 · 23 July 2018

ours

Сервис выбрал по карте — этот был ближе всего. С левого берега ехать далеко, поэтому искал поближе к дому. Сделали то, что обещали, и ничего лишнего. Позвонили, когда можно забирать. Назвали сумму заранее, в конце она не поменялась. Впечатление положительное.

Анастасия Т.Order No. AS-8409 · 1 April 2018

ours

Обращаюсь сюда второй раз, впечатление не изменилось. Сделали то, что обещали, и ничего лишнего. Приняли технику в конце дня, не отправили домой. Общение спокойное, без навязывания. Назвали сумму заранее, в конце она не поменялась. Оформили быстро, без анкет и лишних вопросов. Обращусь снова, если понадобится.

Любовь Ю.Order No. AS-6948 · 27 March 2018

ours

Обращаюсь сюда второй раз, впечатление не изменилось. Было важно успеть до конца недели, а то морозы обещали. Сергей Москоленко посмотрел и честно сказал: менять не надо.

Софья Ц.Order No. TSA-91830 · 8 August 2017

ours

Нужен был срочный ремонт, позванил утром. Выбирал между официальным и этим, выбрал этот. Назвали сумму заранее, в конце она не поменялась. Общение спокойное, без навязывания. Оформили быстро, без анкет и лишних вопросов. Сделали то, что обещали, и ничего лишнего. Не пришлось ездить дважды. Выдали всё официально, для бухгалтерии подошло. Сказали, что запчасть есть на складе. Для Астаны — хороший вариант.

Ярослав С.Order No. AST-1706-376 · 17 April 2017

ours

Обращаюсь сюда второй раз, впечатление не изменилось. Заявку оставил через сайт вечером, утром перезвонили. Рекомендую, без пафоса.

See all reviews
Questions and answersQuestionsTECH SERVICE07

Questions about power tool repair in Astana

Didn’t find the answer? Message us on WhatsApp.

Ask a question
Why won't my cordless drill charge?

Most often the battery itself is to blame: worn cells or a failed protection board. Less commonly, the issue is in the charger or contacts. Free diagnostics will pinpoint the exact cause.

What should I do if the chuck is jammed and the bit won't come out?

Don't try to force the chuck — you could damage the gearbox. A technician will carefully loosen the jaws or replace the chuck. In most cases the assembly is repairable, depending on the model.

Do you repair Makita and Bosch battery platforms in Astana?

Yes, our technicians work with cordless tools from these brands, including platform batteries. We restore batteries or replace failed cells. Diagnostics are free.

Is it worth repairing a cracked power tool housing?

If the housing is cracked, dust and moisture protection suffers, and a fall could have damaged the armature or bearings. Repairing the housing or replacing parts will prevent further breakdowns. The technician will suggest a solution after diagnostics.

What are the risks of continuing to use a power tool that sparks and smells burnt?

Sparks and a burnt smell indicate a fault in the brushes, winding, or commutator. If you don't stop, it could short the wiring or cause the tool to catch fire. It's best to stop using it immediately and take it to a service center.

Can a rotary hammer gearbox be repaired, or does the whole assembly need replacing?

Often the gearbox can be restored: worn gears and bearings are replaced. But with severe housing wear, the entire assembly may need replacement. The technician will tell you which option is more cost-effective after free diagnostics.

Repair guideArticleTECH SERVICE08

Power tool repair in Astana with a technician visiting within 60 minutes

Kairat A., senior small appliance technician

Author: Kairat A.,Senior small appliance technician

Published
Updated

Tech Service is a direct repair provider for power tools in Astana: our technician comes to your home within 60 minutes or the tool is repaired at our service center. Diagnostics are free, we provide a 1-year warranty on labor and parts, and the technician gives you the price after diagnostics. We repair drills, cordless screwdrivers, rotary hammers, angle grinders, jigsaws, and reciprocating saws from various brands.

What power tools we service

We take in corded and cordless machines — from drills to rotary hammers and cut-off saws. Below we've broken down the categories so you can immediately see if your tool will make it to our workbench.

Drills, screwdrivers, and cordless tools

We service corded and cordless drills and screwdrivers, including Makita and Bosch platforms, and separately handle their batteries and chargers. We work on motors, gearboxes, chucks, trigger switches, speed controllers, and contact groups. A battery loses capacity as its cells wear out: the tool holds a charge for less and less time, shuts down under load, and won't even start with a fresh replacement pack. We check chargers for output voltage and contacts. Cordless tools often fail not because of the motor but due to worn cells and charging contacts, so during diagnostics the technician checks the battery first and only then opens the housing — that way you don't pay for disassembling a working device.

Rotary hammers, angle grinders, jigsaws, and reciprocating saws

We work on rotary hammers, angle grinders (grinders), jigsaws, and reciprocating saws — the tools that most often break under load on construction sites and in workshops. We restore the impact mechanism, frame, and piston of rotary hammers, the armature and stator, the spindle and guard of angle grinders, the roller lifting mechanism of jigsaws, and the guide bar of reciprocating saws. The gearbox overheats when lubrication is low or gears are worn — that's where whining, play, and power loss come from. Bearings hum and develop play, the chuck gets clogged with dust and stops holding bits, and brushes wear down to the point of sparking and speed drops. Impact and cutting tools wear faster if used without breaks: the gearbox and bearings heat up, and the chuck gets clogged with dust, so a preventive check extends service life more noticeably than repairing after a breakdown.

Tools from various brands and household or professional class

We work with tools from various brands, including Bosch, Makita, and DeWalt, and we don't divide them into 'worth fixing' and 'disposable' — the approach depends on the class, not the brand. Professional tools are designed for unit-level service and allow replacement of individual components — armature, bearing, gear. Household tools are often assembled so that the whole unit has to be replaced rather than a part inside it, and during diagnostics the technician explains the difference so you can make an informed decision. We service cordless platforms together with batteries and chargers, and for corded models we check the cable, plug, switch, and control board along with the mechanics. Tech Service also takes in older discontinued models if the unit can still be replaced.

Why power tool repair is needed when there's sparking and overheating

We break down the most common complaints — won't turn on, sparks, overheats, lacks power under load — and what usually lies behind each. By the symptom you can understand in advance what to expect from the service.

Won't turn on or lacks power under load

If the tool won't turn on, the cause is most often in the power circuit — the cord, start button, and speed controller — while loss of power during operation points to worn brushes or motor. A break in the cord near the housing entry is visible from frayed insulation, a stuck start button prevents contact, and a burnt-out controller disables soft start. When the tool hums but doesn't reach the required speed, check the brushes: worn down to the graphite base, they stop transmitting current to the commutator. The electric motor stops working when the winding or armature is damaged — that's a deep fault only visible after disassembly. Don't write off the tool right away: a break in the cord and a stuck button are a common and fixable cause, whereas humming and speed drop under load indicate more serious wear.

Sparks, smells burnt, or hums

Sparking and a burning smell are most often caused by the brush assembly and commutator, while humming and vibration point to worn bearings. When the brushes wear unevenly, contact with the commutator becomes spotty, sparks jump between the bars, and carbon buildup drains power. A burning insulation smell appears if the armature winding overheats — then sparking is accompanied by a drop in speed and darkened commutator bars. Humming without sparks usually comes from the bearings: the grease has worn out, the shaft has started to wobble, and vibration transfers to the housing. Light sparking at idle is common in many machines and not a death sentence by itself, but sparks under load along with a smell are a signal to stop working: in this case, putting off diagnostics costs more than checking right away.

Overheating, jammed chuck, or wet tool

  • Overheating: comes from the gearbox and bearings — worn grease and shaft play create extra friction.
  • Jammed chuck: happens due to a skewed drill bit or debris in the jaws, and you can't unscrew a stuck bit without disassembly.
  • Moisture ingress: after getting wet, contacts and electronics stay damp, and turning it on before drying damages the circuit.
  • Wet housing: water on the winding and board causes a short circuit, so drying and a technician's inspection are a must.
  • Stuck button after dampness: oxidized contacts don't close, and startup won't work until cleaned.

How free diagnostics before power tool repair works

The technician checks the tool's components one by one to find the real cause of the breakdown, not just the first symptom match. Based on the inspection, you get a clear picture of the repair options and decide whether to proceed or decline.

What the technician checks during diagnostics

  • Power circuit: we test the cord, plug, button, and switch — a break or burnt contact can cause the same symptoms as a motor failure.
  • Brush assembly: we assess brush length and commutator condition — worn brushes and carbon buildup on the bars explain sparking and power drops under load.
  • Motor: we check the winding for breaks and turn-to-turn shorts, listen to how the rotor spins, and look for signs of overheating.
  • Bearings: we spin the shafts by hand and listen — humming and play indicate worn supports, which lead to vibration and jamming.
  • Gearbox: we inspect the grease and gears — worn teeth and dry grease cause crunching and loss of torque.
  • Battery and charger: for cordless tools, we check voltage at the contacts and charger operation to distinguish a discharged battery from an electronics failure.

Why diagnostics are free and what happens next

Our diagnostics are free: the technician finds the cause, explains the repair options, and quotes a price, and you decide whether to proceed or decline. The same complaint — "won't turn on" or "overheating" — can be a cheap brush or a winding rewind, and the difference in scope is fundamental. That's why we quote after disassembly and checking components, not based on the symptom description: without opening it up, it would be guesswork, not an estimate. You pay only for the agreed scope of work, and declining after the inspection costs nothing. In my opinion, it's more honest to show the client the worn component and explain what will fail next than to quote blindly.

Diagnostics at home and at the service center

Diagnostics can be done at the client's home or at the service center — the technician arrives with their own tools and checks what can realistically be assessed on site. On a home visit, we can test the power circuit, remove the brushes, check the battery and charger, listen to the bearings, and assess the gearbox without full disassembly. For in-depth motor fault detection, winding rewind, or gear replacement, it's more convenient to bring the tool to the service center, where there are conditions for careful disassembly. Moreover, a technician's visit anywhere in the city takes up to 60 minutes, so the inspection doesn't stretch into half a day. The technician will honestly say which option suits the specific breakdown and won't disassemble a complex component on the kitchen table just for show.

Repair at home or at the service center

We compare two formats — a technician visit and a service center — and explain when each is more convenient, so you can choose based on the type of breakdown and urgency.

How a home visit works

The technician arrives within 60 minutes anywhere in the city, performs free diagnostics on site, and if the breakdown allows, fixes the tool right at your place. The visiting specialist brings everything needed for typical jobs: replacing brushes, power cord, switch, checking the winding. On-site power tool service in Astana is convenient for a rotary hammer, a large angle grinder, a heavy drill/driver — you don't want to haul such tools across town. The technician opens the housing, checks the unit under load, fixes simple faults on the spot, and immediately explains what the diagnostics showed. Such power tool repair at home saves time and eliminates trips across the city. A visit is especially appropriate when you need the tool urgently or it's hard to transport, and after the inspection you already know whether a service center is needed — without a wasted trip. In my opinion, for household breakdowns this is the shortest path: no need to find a car and spend half a day on the road.

When it's better to bring the tool to the service center

You bring the tool to the service center when deep disassembly of the motor or gearbox is required — such work needs stationary conditions and more time. Breakdowns of this type can't be fixed at home in one visit: you need to disassemble the unit, check the bearings, assess the condition of the shaft and winding. If the fault affects the motor or gearbox, the technician during diagnostics will immediately say what can be done on site and what requires the service center — you won't be left with a disassembled tool. The same specialist who came to your home works at the service center, so the breakdown history and inspection results are already known, and no repeat diagnostics are needed. Bring the tool in when you hear a hum from the gearbox, the chuck is jammed, or after getting wet the housing hums under load.

Comparison of repair formats

FormatWhen it suitsWhat is done on siteWhat requires the service center
Home visiturgent, heavy toolsdiagnostics, replacement of brushes, cord, switchdeep motor disassembly
Service center repaircomplex units, gearboxinspection and intakemotor and gearbox disassembly, bearing replacement
Mixed optionunclear cause of breakdowndiagnostics and verdictunit disassembly after approval

Repair or replace the unit

We explain how we decide what's more cost-effective — repairing the unit or replacing it — and what it depends on: the condition of the parts, the tool class, and the nature of the breakdown.

Battery — replace the battery or restore it

When the battery doesn't hold a charge, we first check the cells and charging contacts, and the decision — replace the battery or restore it — depends on the condition of the cells. During diagnostics we measure the voltage on each cell of the battery and see if it holds under load: a sagging cell drags down its neighbors, and then the whole block is replaced, not just one part. We also check the charger and contacts separately — an oxidized contact gives the same symptom as a dead battery. Moreover, the problem isn't always in the battery itself: sometimes the charger and loose contacts are to blame, so replacing the battery right away means risking spending money on the wrong part. Diagnostics will show where exactly the failure is — and only after that we say what to restore and what to replace.

Chuck, housing and other units

  • Chuck: jams when the bit is skewed or debris gets in — usually repairable if the part isn't damaged and the jaws are intact.
  • Housing: a cracked part is replaced when it affects safe operation, not just appearance.
  • Other components: we assess the gearbox, motor, and electronics by wear — we replace the unit if repair won't restore its working parameters.
  • Mounting points: we check the fasteners — if the housing holds the motor and gearbox, it's repaired; if not, it's replaced.
  • Cracks under load: a damaged housing that "still works" can split and catch internal components.

When repair is more cost-effective than buying a new tool

Repair is usually more cost-effective when the tool is professional-grade and the breakdown affects one component rather than the whole motor. Professional tools are designed for component replacement and last a long time after repair, while a household tool with serious motor damage is sometimes cheaper to replace — during diagnostics we'll outline the scope of work, and the decision is yours. Our technicians have 7 to 20 years of experience, and they'll honestly tell you when repair doesn't make sense: if after replacing the motor the tool still won't return to its working parameters, investing in it is a waste. The cost depends on the number of components to replace, not the tool's class, so we give the final price after free diagnostics. The decision is always yours — we provide the scope of work and the likely outcome, without pushing replacement.

Warranty and why choose direct service

We explain exactly what our warranty covers, why a direct provider is more accountable for results than an intermediary, and how payment and timelines work after free diagnostics.

What the 1-year warranty covers

What the 1-year warranty covers — We provide a 1-year warranty on labor and parts — both for replaced brushes and bearings and for any other component we've changed. If the same component fails again a few months after service, you come back to us instead of looking for a new provider. The warranty covers both the part itself and how it was installed: one party is responsible for both, so you don't have to figure out whether the part supplier or the technician is at fault. A warranty on parts separate from labor matters because a new part can also fail — in that case you return to us instead of trying to determine who's to blame, the part or the specialist. Practical tip: keep your service documents — they make it easier to confirm the case and the timeframe, and if the same component fails again, let us know right away without disassembling or replacing the part yourself, so the warranty stays valid.

A direct provider, not an intermediary

Tech Service is a direct provider: our own employee services the tool, not a third-party organization, so you always know who's responsible for the result. We're not an aggregator or intermediary — the same team takes and fulfills the request, our specialist comes to your home or takes the tool at the service center, and payment for the work doesn't go to a third party. With an intermediary scheme, the equipment goes through an extra loop: receiver, handover, someone else's workshop — and at each stage responsibility is blurred between those who accepted the tool and those who opened it. When a device is passed through an intermediary, it's hard to find who's at fault for a repeat breakdown, while with direct service the warranty and claims are addressed to one party — that's the difference you feel when you come back.

Technician experience, payment, and timelines

  • Experience: our specialists have 7 to 20 years of experience — across various components and tool types.
  • Payment: we accept Kaspi QR, Kaspi Red, bank card, cash or bank transfer, you choose the one.
  • Timelines: the specialist gives the timeframe after free diagnostics — it depends on the breakdown and the required component.
  • Cost: we state the amount there as well, after diagnostics, before work begins — no surprises at the end.
  • Benchmark: the accuracy with which the employee names the cause even before disassembly shows their qualification.

Power tool repair and what it involves

Here's a quick summary of what determines the outcome of equipment restoration: why tools fail, how the cause is found, and how the repair is completed.

  • Common causes of failure: brushes, bearings, chuck, gearbox, and battery — the technician identifies the faulty unit from the symptom during diagnostics.
  • Free diagnostics: the check goes from simple to complex, so the cause is found without unnecessary disassembly of the tool.
  • Home or service center: typical jobs are done on-site, while the motor and gearbox are disassembled in the workshop.
  • Repair or replace: the choice depends on the tool class and the extent of the breakdown, and is made after inspection.
  • Warranty and direct provider: a year on labor and parts plus a technician without intermediaries reduce the risk of repeat visits.

33brands

Which power tool brands we repair in Astana

The list above is not exhaustive: each brand has its own housing and gearbox disassembly, and the technician takes this into account during inspection.

We also repairWe also repairTECH SERVICE09

Besides power tool repair, we fix other equipment in Astana

Tech Service technicians repair other appliances too — with the same 1-year warranty on labour and parts.

BlogBlogTECH SERVICE10

Worth reading before power tool repair in Astana

Leave a review

Choose a platform — the TECH SERVICE page will open.

Send a review with photos on WhatsApp