Original
Part by model number
- Selection
- By part number or model, for Bosch — by E-Nr
- Compatibility
- Matches the mounting seats of the specific model
- What to clarify
- Availability and delivery time from the technician
- Warranty
- 1 year on labor and parts
City
Language
What broke
Sections
Message on WhatsApp+7 (778) 746 00 26Mon–Fri 10:00–19:00, Sat–Sun 11:00–18:00
We restore the rotating assembly of the tub: bearings, seal, and the drum-to-shaft mount. Free diagnostics, technician arrives within 60 minutes.
Our own technicians4 to 20 years of experience




1 yearwarranty on labor and parts
60 minutestechnician visit across the city
Freefree diagnostics
The technician disassembles the tub, removes the drum, replaces the bearings and seal, and checks rotation and balance. The cost of labor and parts is quoted after free diagnostics. There is a 1-year warranty on labor and parts.
01
Step 1varies
We remove the tub, unscrew the housing, take out the drum with the shaft, and inspect the mounting seats.
02
Step 2varies
We install a new bearing kit and seal, lubricate the assembly, and reassemble the tub.
03
Step 3varies
We replace the door gasket and hoses if cracks, hardening, or signs of leakage are found during inspection.
04
Step 4varies
We spin the drum by hand, check for smooth movement, absence of shaft play, and proper balance.
05
Step 5varies
We run a short spin cycle and listen to the assembly under load to confirm the result.
5
Five typical symptoms point to wear of the rotating assembly: humming during spin, stopping mid-cycle, leaking, no rotation, and vibration. The sooner the assembly is inspected, the easier it is to determine the cause.
Humming and vibration during spin
Humming appears only at high spin speeds or at low speeds too — this will help the technician narrow down the search.
Drum doesn't rotate
Specify whether it doesn't rotate by hand or only under load with laundry — these are different symptoms for the request.
Leaking from below and at the door
Describe where it drips — at the door or from under the machine — and at what point in the cycle water appears.
Stopping mid-cycle
Note at which phase the machine stops and what the display shows — this will speed up diagnostics.
Water fill issues
Check if the tap is open and if the hose is kinked — if water flows but the error remains, the cause is in the assembly.
The part is selected by part number or machine model. The exact diagnosis is made by the technician after inspecting the assembly.
Describe the symptomsThe part is selected by part number or machine model; for Bosch, the E-Nr number is on the label inside the door.
Original
or
Analog
The table lists the 'from' price for labor, for common jobs also the 'from' price of the part, plus the time required to complete the job.
2–4 hourstime
from 11 500 ₸cost

BeforeAfterWe reply during working hours
The technician will inspect the assembly on site and make an accurate diagnosis without transporting the machine to the service center. Ask them about payment and acceptance procedures.

Warranty question? Call us
+7 (778) 746 00 266 127 reviews of repairs at TECH SERVICE in total
Зоя М.Order No. AST-2611-737 · 16 September 2026
oursЗаявку оставил через сайт вечером, утром перезвонили. Жалоба одна: вибрация. Третий месяц — никаких проблем.
Семён Ш.Order No. TSA-54682 · 19 June 2026
oursС чем обратился: шумит при отжиме. Дильмурат С посмотрел и честно сказал: менять не надо. Вернули — проверил, всё ок.
Валерий Д.Order No. AS-9920 · 2 June 2026
oursОсновная жалоба — шумит при отжиме. Астанинский Tech-service — нормальный вариант. Вернули — проверил, всё ок
Ярослав С.Order No. AST-2508-434 · 8 December 2025
oursЖалоба одна: не сушит. Ораз показал старую деталь, всё прозрачно. Пользуюсь и вспоминаю добрым словом.
Зоя М.Order No. AS-7170 · 19 July 2025
oursПервое, что заметил: не отжимает. Рустем Т сам позвонил и сказал, что готово. Крутит ровно, без рывков.
Маргарита П.Order No. 2204-6395 · 2 January 2022
oursС этим и пришёл: не сливает воду. Ораз подобрал аналог дешевле, не навязывал оригинал. Третий месяц — никаких проблем)
Борис В.Order No. AS-1453 · 10 June 2020
oursВыбирал между официальным и этим, выбрал этот. Если честно, руки опустились, когда оно щёлкнуло и затихло. Первое, что заметил: не включается. Приехал без записи, но свободный мастер нашёлся. Вскрытие показало: насос. Работает, даже лучше прежнего.
Елизавета Л.Order No. 16154 · 21 April 2020
oursПервое, что заметил: ошибка на дисплее. Дильмурат С посмотрел и честно сказал: менять не надо. Шум ушёл, работает мягко.
Денис Л.Order No. TSA-10827 · 4 March 2020
oursС этим и пришёл: не сливает воду. Ораз отсоветовал дорогой ремонт, предложил простой. Вернули — проверил, всё ок.
Виолетта Д.Order No. TSA-56476 · 24 April 2019
oursОсновная жалоба — не греет воду. Дима принял без вопросов, хотя был без записи. Стоит, работает, радует)
experience10 yearsSenior washing machine technician
experience16 yearsWashing machine installation technician
experience12 yearsWashing machine repair technician
experience10 yearsWashing machine board repair technician
experience11 yearsDishwasher repair technician
Didn’t find the answer? Message us on WhatsApp.
Ask a questionA worn drum assembly shows up as humming and knocking during the spin cycle, vibration, rusty streaks around the door, and water underneath. If the drum wobbles when you rock it by hand or the machine stops spinning, it needs diagnostics.
Yes, working parts — the pump, heating element, motor, door seal — are often bought for parts. But first check with a technician to see if restoring the drum assembly and keeping the machine would be cheaper.
If the machine can't be repaired, you can sell it for parts or recycle it. Before that, after diagnostics the technician will tell you whether restoring the drum assembly is worth it.
Most often drum play means a worn bearing, but something similar can happen when the spider or shaft breaks down. The exact diagnosis is made by a technician after disassembly and depends on the model.
Minor repairs and bearing replacement are often done at home if conditions allow. In complex cases with a sealed tank, the machine may be taken to the service center — the technician will decide after diagnostics.
On Bosch machines, humming during the spin cycle is most often linked to a worn bearing, but it can also be caused by imbalance or a foreign object. The exact cause will be determined by a technician after disassembly and depends on the model.

Author: Vladimir V.,Senior washing machine technician
Published
Updated
Tech Service repairs washing machine drums in Astana as a direct provider: our own technician arrives at your home within 60 minutes anywhere in the city, diagnostics are free, and there's a 1-year warranty on labor and parts. We replace bearings, seals, and shafts; for sealed tubs, we install a tub assembly. The technician gives you the price after free diagnostics.
Strange noise at high spin speeds doesn't always mean the drum is done for. Here's how to tell bearing wear from imbalance, worn shock absorbers and a stretched drive belt. Below are the signs of each.
A growing hum that gets louder with speed usually points to the drum bearing, not an overload of laundry. Bearings wear out together with the shaft seal: water gets past a damaged lip seal to the race, the grease washes out, and the metal starts to sing. At high speeds, usually 800–1600 rpm depending on the model, the sound becomes dense and low, like an airplane, and it doesn't go away on a spin cycle with no laundry. Overload and imbalance give a different effect — rhythmic knocking and jerking that stop if you pause the cycle and redistribute the items in the drum. If the noise remains after even loading and checking the feet, it's not imbalance: with bearing wear, the sound doesn't disappear on a spin with no laundry. The technician quotes the price for washing machine drum repair after free diagnostics.
Strong vibration and "jumping" at high speeds are more often linked to worn shock absorbers and bunched laundry than to the drum itself. Shock absorbers damp the tub's movement, usually 800–1600 rpm depending on the model, and when they weaken, the machine bangs on the floor even with a good bearing. Imbalance makes it worse: one heavy item or a clump of laundry shifts the center of gravity, the tub swings, and the shaking transfers to the cabinet. The noise stays steady — it doesn't depend on how the laundry is distributed. That's why shaking is checked separately from humming: the technician inspects the shock absorbers and only then draws a conclusion about the bearing. If the machine jumps but doesn't hum, start with the shock absorbers and loading, not with taking the drum apart.
The tub design determines the choice: replace the bearing separately or install the whole assembly. We cover both options, their specifics, and how the technician checks the unit before deciding.
We replace the bearing separately only if the tub is split; for a sealed tub, we install the assembly with the drum. A split design is held by bolts or clips: it's opened, the old bearings are pressed out, the seal is replaced, and it's reassembled with a new gasket. A sealed tub is glued or welded along the seam — you can only reach the bearings by cutting the housing and resealing the joint. In both cases, the drum shaft is checked for wear and play: if it's worn, replacing the bearings alone isn't enough. Cutting open a sealed unit isn't a universal solution — the seal after the intervention holds worse than the factory one, so for such designs, replacing the assembly is more reliable. At the slightest doubt about the shaft fit, it's better to install a whole unit right away than to come back to a leak.
| Tank type | What we replace | What we check | Key point |
|---|---|---|---|
| Split | Bearings, seal | Drum shaft | Bearing is replaced separately |
| Sealed | Complete unit | Shaft fit | Can be cut open, but less reliable |
| Any | Shaft seal | Play and shaft wear | Seal is replaced together with the bearing |
We walk you through the process from request to finished machine: how a home visit works, when repair at the service center is needed, and why bearing replacement is considered the longest job.
Our diagnostics are free: a specialist comes to your home, checks the unit, and only then quotes the price for labor and parts. During the inspection, they listen to the machine during the spin cycle, check whether the drum turns freely, and examine the door seal, hoses, and drain filter behind the service flap at the bottom front. Based on the results, they explain which part has failed — the bearing, shaft, or tank — and what parts will be needed. The price is given before work begins, so the owner makes a decision with a clear picture, not over the phone. This is the main difference of on-site diagnostics: a phone conversation about a washing machine drum in Astana is always based on guesses, while an on-site inspection removes the uncertainty. That's how washing machine drum repair in Astana starts with a precise understanding of the scope of work.
Bearing replacement is the longest job in drum service because the tank and drum have to be removed rather than swapping a part in place. First, the hoses, heating element, and motor are disconnected, then the tank is taken out of the housing. Next, the drum is disassembled, the old bearings and seal are pressed out, new ones are pressed in, and the unit is reassembled — this is possible with a split tank; in a sealed tank the bearing is not replaced separately. Because of the amount of disassembly, this work is done at the service center, not at home: during diagnostics we'll tell you which format suits your machine. The technician gives the timeline after inspection. This stage often worries owners — it seems like the machine is being taken apart 'down to the last screw', though after reassembly the unit is put back together and tested.
A drain error often accompanies drum and pump problems. We explain what the code means for different brands and how to safely drain water before the technician arrives.
Sometimes restoring the drum assembly no longer makes sense, and sometimes it's exactly what extends the machine's life for years. We explain when repair isn't worth it and how a technician visit works.
Restoring the drum assembly stops making sense when the cost of labor and parts approaches the price of a new machine, or when not only the bearing but also the shaft and tub are worn. The price of washing machine drum repair depends on the condition of the assembly and the parts needed—the technician assesses the scope after free diagnostics. Bearing replacement is the longest operation: the tub and drum are removed from the housing, and on sealed tubs the assembly is replaced as a unit. If there's also wear on the shaft, restoration costs more than the housing with working electronics is worth. With a sealed tub and a worn seat, replacing the tub as a unit is considered. Scratches and chips on the drum don't affect whether repair is worthwhile. The technician gives the price for drum repair on site.
We offer a 1-year warranty on labor and parts, and a technician arrives within 60 minutes anywhere in the city. The warranty covers both bearing replacement and tub assembly replacement. Tech Service is a direct provider: our own technician comes to your home, not a middleman, and gives you the price after free diagnostics. You can pay via Kaspi QR, Kaspi Red, bank card, cash, or bank transfer for companies. To call a technician, describe the symptom and the machine model: using the error code and the type of noise, the specialist will know in advance whether the tub needs to be disassembled. When you request service, mention whether your tub is split-able—this determines the scope of work. If you don't know the model, give the brand and approximate age of the machine: the technician will use that to anticipate the tub design. This way the visit goes faster and diagnostics start with the right check.
Quick summary on the drum assembly: the order of initial checks, when to replace the shaft support, and the point after which repair is no longer justified.
If you ask, the technician will check other parts during the same visit.
Refrigerator Repair in Almatyfrom 3 000 ₸
Dishwasher Repair in Almatyfrom 3 500 ₸
Oven Repair in Almatyfrom 3 000 ₸
Cooktop Repair in Almatyfrom 3 500 ₸
Air Conditioner Repair in Almatyfrom 3 500 ₸
Boiler and Water Heater Repair in Almatyfrom 2 500 ₸
Freezer Repair in Almatyfrom 6 000 ₸
Tumble Dryer Repair in Almatyfrom 5 000 ₸
A washing machine can hum for many reasons, and the first thing to figure out is when the sound appears.
20 March 2026 · 12 minutes read
If your washing machine isn't filling with water, the most common culprits are a closed valve, a clogged inlet filter screen on the hose…
20 February 2026 · 13 minutes read
Washing machine error codes are self-diagnostic codes that point to a specific component: drain, water fill, heating, motor, or door lock.
29 January 2026 · 13 minutes read
If your washing machine won't spin, it's usually an unbalanced load, a clogged drain filter or hose, and less often the pump, belt…
19 January 2026 · 12 minutes read
If your washing machine isn't heating water, the heating element or temperature sensor is usually to blame, less often the control board or wiring.
25 December 2025 · 12 minutes read
If your washing machine won't turn on, first check the outlet, extension cord, and the circuit breaker in your panel, then the plug and power cord.
24 November 2025 · 13 minutes read