Open until 19:00+7 (778) 746 00 26Call a technician
Tech Service technician next to a refrigerator

Beko Refrigerator Repair in Astana

A technician arrives within 60 minutes anywhere in the city. Free diagnostics, 1-year warranty on labor and parts.

  • 1-year warranty on labor and parts
  • Free diagnostics
  • Technician experience from 4 to 20 years

Our own technicians4 to 20 years of experience

Yerkimbek S.Vladimir V.Beknur D.Ozat K.

Repair prices

  • Diagnostics0 ₸
  • Filter drier replacementfrom3 000 ₸
  • Drain line cleaningfrom4 500 ₸
  • Door rehanging / adjustmentfrom4 500 ₸
  • Leak detection and repairfrom5 000 ₸
All prices
ours5,06 127 reviews
order database
Common faultsCommon faultsTECH SERVICE02

Common Beko refrigerator faults in Astana

Below are frequent symptoms and the most likely cause. The technician pinpoints the exact component during diagnostics.

PricesPricesTECH SERVICE03

How much Beko refrigerator repair costs in Astana

The table lists the 'from' price for labor, for common jobs also the 'from' price of the part, plus the time required to complete the job.

Filter drier replacementrefrigerant not included

1–2 hours

from3 000 ₸

Drain line cleaninglabour only

1–2 hours

from4 500 ₸

Door rehanging / adjustmentlabour only

1–2 hours

from4 500 ₸

Leak detection and repairrefrigerant not included

1–3 hours

from5 000 ₸

Door seal replacementparts not included

1–2 hours

from5 500 ₸

Before and afterBefore and afterTECH SERVICE04

Before and after Beko refrigerator repair in Astana

Temperature Not Maintained Due to Thermostat

1 visittime

from 6,000 ₸cost

Problem
The Beko refrigerator was not maintaining temperature: it either over-froze food or warmed up, and the compressor did not turn off on time due to a faulty thermostat.
What we did
The technician opened the thermostat housing in the chamber, replaced the thermostat, connected the wires, and checked the compressor's on and off operation.
Result
The temperature in the refrigerator stabilized, and the compressor turns on and off on time. 1-year warranty on labor and parts.
I want the same
An open white refrigerator with glass shelves in a kitchen with cream-colored cabinets; a technician in an orange shirt holds a new thermostat at the open door, with the wire running into the wall of the chamber.BeforeAfter
01 / 04
All repairs
TECH SERVICE mobile technician with a tool case

How Beko refrigerator repair works at your home in Astana

From request to inspection — five steps, free diagnostics.

  1. Requestfast

    Submit a request — a technician will arrive within 60 minutes anywhere in the city.

  2. Diagnosticsfree

    The technician will arrange a convenient visit time and ask you to provide access to the refrigerator.

  3. Approvalbefore repair

    You approve the scope of work and parts, and only then does the repair begin.

  4. Repairon-site

    The technician performs the work and tests the refrigerator under load.

  5. Inspection and warrantyafter repair

    Check the cooling and that there's no noise, and ask the technician about the warranty terms.

Leave a request

We reply during working hours

Book Beko refrigerator repair in Astana

Describe the issue in the way that's convenient for you — the technician will arrange a visit time. There's a 1-year warranty on labor and parts.

TECH SERVICE administrator replying to a customer's WhatsApp message

Warranty question? Call us

+7 (778) 746 00 26
Customer reviewsReviewsTECH SERVICE05

Reviews of Beko refrigerator repair in Astana

5,0ours

6 127 reviews of repairs at TECH SERVICE in total

Геннадий Ж.Order No. 2601-4185 · 28 October 2026

ours

Позвонил в четыре места, тут ответили по-человечески. Открыл — и сразу понял: не морозит. Замена: компрессор. Сравнивал — здесь дешевле. Ни шума, ни запаха, всё штатно.

Repair: refrigerator repair in

Константин О.Order No. AS-4180 · 4 October 2025

ours

Первое, что заметил: намерзает лёд. Вернули — проверил, всё ок). Работает, как будто и не ломалось.

Repair: refrigerator repair in

Екатерина К.Order No. TSA-51912 · 4 November 2023

ours

Проблема ровно одна: шумит. Дильмурат С отсоветовал дорогой ремонт, предложил простой. Проверил на всех режимах — держит)

Repair: refrigerator repair in

Людмила Щ.Order No. 96289 · 14 July 2022

ours

Причина обращения — не морозит. Никита М пообещал и сделал, без напоминаний. Сейчас пашет без нареканий

Repair: refrigerator repair in

Лаура О.Order No. AST-2107-903 · 27 December 2021

ours

Телефонмен кеңестім, кейін апардым. Мастер бәрін түсіндірді. Түскі үзіліске қарамастан қабылдады. Барлығы ресми, чек берді. Диагностика тегін болды. Бөлшек қоймада бар екен, күтпедік. Жұмысты сол күні аяқтады. Кепілдік берді, бұл маңызды. Келесіде де осында келемін.

Repair: refrigerator repair in

Альбина Ю.Order No. AST-2001-960 · 27 April 2020

ours

Заявку оставил через сайт вечером, утром перезвонили. Думал, попал на дорогой ремонт. Симптом как на ладони: шумит. В другом месте просили на треть больше. Полёт нормальный.

Repair: refrigerator repair in

Денис Л.Order No. 1905-8876 · 13 February 2019

ours

Сосед по площадке хвалил, решил проверить. Больше всего мешало: не морозит. Работает, как будто и не ломалось.

Repair: refrigerator repair in

Иван Н.Order No. ZK-2017-701 · 4 December 2017

ours

Раньше обращался в другой сервис, там очередь на две недели. После скачка напряжения — шумит. Сделали так, что и не придерёшься.

Repair: refrigerator repair in

Валентина Р.Order No. TSA-79156 · 30 January 2017

ours

Заявку оставил через сайт вечером, утром перезвонили. Не хотел везти, думал, проще новое взять. С чем обратился: не морозит. Никита М — мастер от бога, если можно так сказать. В 26 000 уложился, как и обещали. Приняли вечером, хотя до закрытия оставалось минут десять. Пришлось ставить: модуль. Пять баллов. Тихо, ровно, без сюрпризов.

Repair: refrigerator repair in

Григорий И.Order No. 12682 · 25 September 2016

ours

Переезжали в новую квартиру, техника после перевозки захандрила. Жалоба одна: течёт. Дома включил, всё на месте.

Repair: refrigerator repair in
See all reviews

Our technicians in Astana

01 / 08
Vladimir V., senior washing machine technicianexperience10 years

Vladimir V.

Senior washing machine technician

Beknur D., stove and oven repair technicianexperience11 years

Beknur D.

Stove and oven repair technician

Ozat K., freezer repair technicianexperience11 years

Ozat K.

Freezer repair technician

Adilkhan N., washing machine installation technicianexperience16 years

Adilkhan N.

Washing machine installation technician

Daulet D., dishwasher technicianexperience8 years

Daulet D.

Dishwasher technician

Temirlan B., washing machine repair technicianexperience12 years

Temirlan B.

Washing machine repair technician

Miras O., washing machine board repair technicianexperience10 years

Miras O.

Washing machine board repair technician

Questions and answersQuestionsTECH SERVICE06

Questions about Beko refrigerator repair in Astana

Didn’t find the answer? Message us on WhatsApp.

Ask a question
Is it better to repair an old Beko refrigerator or buy a new one?

If the problem is minor — a relay, sensor, door seal, or fan — repairing an old Beko is usually cheaper than buying a new one. Replacing the appliance makes more sense if the compressor and electronics have seriously failed, and a technician can assess that after a free diagnostic.

What does a flashing temperature indicator on a Beko refrigerator mean?

Flashing usually signals that the temperature inside the compartment is above normal: the door was left open for a while, the fridge was recently defrosted, or the settings got changed. If the indicator keeps flashing after you reset the mode, it depends on the model — it can point to a faulty sensor, defrost system, or refrigerant leak, and you'll need a technician.

Why does a Beko No Frost refrigerator build up ice in the freezer?

Most often the defrost system is to blame: the heating element, sensor, or defrost timer stops working, and ice doesn't have time to melt. Less commonly, it's the door seal or a clogged drain. A technician checks the defrost circuit and pinpoints the specific component.

Can the inverter compressor in a Beko refrigerator be repaired separately from the control board?

It depends on the model and the nature of the fault: sometimes the compressor is fine and the problem is in the electronic module or the start-up part. Diagnostics show exactly what has failed, and there's no point replacing a working component. The decision is made after testing both parts.

How can you tell if a Beko refrigerator's control board is burned out rather than a sensor?

When the board fails, the appliance often behaves erratically: it won't turn on, doesn't respond to buttons, shows an error, or flashes all indicators. A faulty sensor usually gives a more localized symptom — wrong temperature in one compartment. A diagnostic of the electronics will tell them apart for sure.

Is it dangerous to keep using a Beko refrigerator that clicks and won't start?

Yes, it's best not to leave it plugged in: clicking when it tries to start often means a faulty start relay or compressor, and repeated attempts can finish off the component. Unplug the appliance and call a technician to your home.

Repair guideArticleTECH SERVICE07

Beko refrigerator repair in Astana by a direct contractor

Yerkimbek S., dishwasher repair technician

Author: Yerkimbek S.,Dishwasher repair technician

Published
Updated

Tech Service repairs Beko refrigerators in Astana: our technician comes to your home or accepts the appliance at the service center. Diagnostics are free, arrival within 60 minutes anywhere in the city, and a 1-year warranty on labor and parts. The technician gives you the price after diagnostics, and you can pay any way you like.

Why your Beko refrigerator isn't cooling and what the indicator lights mean

The fridge seems to be running, but food in the compartment spoils — that's the most common reason for a call. Let's break down what the Beko indicators mean and how to narrow the cause down to a specific component.

Beko refrigerator not cooling but the light is on

We start by checking the compressor and the start relay, because when the light is on and the motor compartment is silent, the cause is usually in the start unit, not the electronics. The electronic control module and temperature sensors are checked next: they only send a command to the motor, and if the motor itself is silent, there's no point looking for a fault in them. On Beko appliances, the start relay is a wear item — it fails from frequent voltage spikes in the mains and from age. Our diagnostics are free, a specialist arrives anywhere in the city within 60 minutes, and first tests the compressor windings to separate a burnt-out motor from a stuck relay. If the compressor hums but doesn't start, then clicks and goes silent after a minute, that's the classic picture of a stuck relay, and you shouldn't delay the call: the winding is heating up. We repair Beko refrigerators in Astana either at your home or at the service center, and the technician first confirms the cause and only then replaces the component.

What a flashing indicator and Beko error codes mean

On Beko, a flashing temperature indicator is the module's signal that the sensor is detecting a deviation from the set mode, and the flashing pattern tells you whether it's the fridge or the freezer compartment. A steady light usually indicates emergency mode after a voltage spike, while a blinking light means the sensor is out of its operating range. The electronic control module logs deviations in sensor operation, so the indication is analyzed before taking the compartment apart. Beko temperature sensors are installed separately in each compartment and on the evaporator, and one failed sensor throws off the entire defrost algorithm. An error code by itself doesn't name the broken part — it points to a circuit, and then the sensor, wiring, and connector are checked so you don't replace a working component.

How to tell a refrigerant leak from a thermostat failure

We distinguish these causes by how the circuit behaves: with a refrigerant leak, the compressor runs nonstop while the evaporator stays warm, whereas with a faulty thermostat the motor simply doesn't get a start command. The check takes a few minutes: the evaporator circuit is felt by hand and the motor is listened to, and the system pressure confirms the lack of refrigerant. A thermostat usually fails gradually — the compartment either holds temperature or drifts warm, and you can see it in the food. The door seal matters here too: a loose seal causes the same lack of cold as a leak, but the compressor runs in bursts. Frost buildup in the freezer while the compressor is running usually points to a defrost failure or a loose door seal, not a refrigerant shortage.

Common Beko failures by component

Beko has its own weak spots — the inverter compressor, the electronics, and No Frost defrost. Here's what breaks and how it shows up in everyday use.

Compressor and start relay — how to tell the difference

We check the relay first because it fails more often than the motor and requires replacing the start unit, not the whole assembly. A working motor with a new part starts right away. The Beko start element is a small part on the motor housing that gives the winding a starting pulse; when its contacts break down, the unit hums, clicks, and goes into protection within seconds. We test the winding with a multimeter for resistance and for a short to ground: on a working motor the values are stable within the range specified for the model, while on a burnt-out one, one of the windings reads zero or open. Our technicians replace the part on site — it's a quick operation that usually brings the cold back. If the motor still hums and shuts off on overload after replacement, the problem is in the winding, and then we discuss replacing the assembly, not the start unit.

Inverter compressor and electronics after a power surge

The Beko inverter compressor adjusts speed smoothly, so a steady quiet hum is normal, while a sharp metallic sound or jerking at startup indicates a problem with the board or the unit itself. In inverter models, the motor is powered through an electronic block that converts voltage and sets the rotation frequency. During a power surge, this block is the first to fail — the power switches or capacitors on the board burn out, and the fridge won't start, works intermittently, or the indicators flash. We check the Beko electronic control module: we test the power section and determine whether the block can be restored or needs replacement. After a power surge, the control board is the first to suffer, and restoring the electronics often gets the fridge working again without replacing the expensive unit.

How No Frost maintenance differs from a drip system

Beko systemWhat we check firstCommon failure symptomTypical work
No FrostHeating element, timer, and defrost sensorIce buildup in the freezer, weak coolingDefrost restoration
Drip (Direct Cool)Door seal, drainagePuddle under the drawers, ice on the wallDoor adjustment, drain cleaning
InverterBoard, compressorJerking, sharp hum at startupElectronics repair, unit replacement

How Beko refrigerator repair works in Astana

We handle Beko refrigerator repair in Astana as a direct contractor, without intermediaries. Here's how the visit works, what the technician does in your kitchen, and when the appliance needs to be taken to the service center.

Technician at home or work at the service center

We service Beko refrigerators both at home and at the service center: most breakdowns are fixed on site, and the appliance is taken to the service center when work can't be done in the kitchen. During a home visit, we can replace the start relay, thermostat, sensors, door seal, work on the control board, and locate refrigerant leaks in the circuit. At the service center, we perform work that can't be done in the kitchen — for example, compressor replacement or fixing a leak in the circuit. We provide free diagnostics at home, so the format is determined by the actual condition of the components, not by a phone description. The technician decides on the format after diagnostics — if a component can be replaced on site, the fridge doesn't need to be transported and you don't have to wait.

How fast the technician arrives and how the visit goes

We arrive within 60 minutes anywhere in the city, and diagnostics are free, so you'll know what's broken and what work is needed already on the first visit. The technician inspects the fridge, checks the compressor, start relay, sensors, and door seal, compares readings with error codes on the display, and outlines the scope of work. Then they agree with you on the list of replacements and the cost — no numbers in this article because pricing depends on the component and model. During the visit, the technician checks typical components — relay, sensors, seal — and determines what can be replaced right away and what requires work at the service center. If the fridge is hard to access, it's sometimes easier to take the unit out than to disassemble it against the wall.

Why a direct contractor, not an intermediary

Tech Service is a direct contractor: the work is done by our technician with 4 to 20 years of experience, not by a subcontractor found through a request. There's no dispatcher between you and the person who arrives, passing the request along and adding their markup to the work. The 1-year warranty covers both labor and parts, and you can pay via Kaspi QR, Kaspi Red, card, cash or bank transfer. When the work is done by the same person who diagnosed it, one party is responsible for the result and the warranty, and there's no dispute between dispatcher and contractor. In my opinion, that's the main difference of this format: you know in advance who will arrive, who is responsible for the result, and who to claim against under the warranty if the breakdown happens again.

Warranty, diagnostics, and terms of service

A warranty and clear terms remove the last barrier before you book a service. Below we explain what our warranty covers, what goes into the price, and which parts for Beko are needed most often.

What the 1-year warranty covers

We provide a 1-year warranty on labor and parts, so if a repaired Beko component fails again, the repeat repair of that component is covered by the warranty. This applies both to on-site visits and to service at our workshop. Our technicians have worked with this brand for 4 to 20 years, so they identify the cause of a repeat failure by inspecting the component, not by guessing. The warranty covers both the part and the technician's work — this matters because the cause of a repeat failure is not always obvious and should not fall on the owner. When you contact us about a warranty claim, describe how the failure showed up: the type of sound, the indicators on the panel, and when the fridge stopped keeping cold — these details speed up finding the component.

How the price is formed and what free diagnostics gives you

The technician gives you the price after free diagnostics, once it's clear which Beko component has failed and what work is needed. Before that, the conversation is about symptoms, not the sum: whether the compressor runs smoothly, whether the compartments hold temperature, what the indicators show. Diagnostics are free with us, and a technician arrives within 60 minutes in the city, so the owner decides on the work based on the actual inspection, not a phone guess. You can pay via Kaspi QR, Kaspi Red, bank card, cash, or bank transfer for companies. Free diagnostics benefit both the owner and the technician: it rules out cases where repair is not worthwhile and keeps the visit from turning into a charge for an inspection. In my view, this step most often removes any suspicion of unnecessary work — the technician sees the component with their own eyes and speaks about it specifically.

Which Beko parts are usually needed

  • Start relay: responsible for starting the compressor, wears out first and is replaced as a separate part.
  • Temperature sensors: give the module data about compartment conditions; their failure causes the indicator to blink.
  • Door seal: ensures a tight fit and keeps the cold in; wear leads to frost buildup.
  • No Frost defrost components: heating element, timer, and sensor; their failure causes frost in the freezer.
  • Compressor and module: replaced less often, after checking the relay and electronics.
  • Correct diagnostics vs. unnecessary replacement: inspection rules out cheap causes before touching an expensive component.

Special cases after moving and defrosting

Some Beko failures are not due to wear but to moving, defrosting, or attempting a DIY repair. Let's look at where DIY ends and when diagnostics are needed.

Beko fridge won't turn on after being moved on its side

After being moved on its side or at an angle, a Beko fridge needs to stand upright before you plug it in; otherwise oil from the compressor gets into the circuit and the appliance either won't start or runs intermittently. Oil flows into the discharge tube and capillary, and on first start the compressor tries to push through a plug of liquid — hence humming without cooling, clicks from the start relay, and the protection tripping. The longer the appliance was on its side, the longer it needs to stand upright; and if it was moved in freezing weather, let it warm up to room temperature so condensation on the board doesn't cause a short circuit. If the appliance still won't start after standing, the cause may be the relay or the compressor, and then diagnostics are essential — these components can't be checked by ear or by appearance.

Not cooling after defrosting and should you replace the seal yourself

If your Beko fridge stops cooling after defrosting, the problem is usually a sensor or a defrost failure, not the defrosting itself. You can replace the door seal yourself, but only if you get the exact part for your model. During manual defrosting, owners sometimes damage the defrost sensor or knock it out of place, and the No Frost system stops cycling — the evaporator ices up and cold air no longer reaches the compartment. The seal is a different story: a door that's misaligned on its hinges or rubber that's lost its flexibility leaves a gap that lets warm air into the compartment. A seal with the wrong profile won't close tightly, and ice builds up again — that's why you match the part to the model instead of guessing.

Repair an old Beko or buy a new one

The decision depends on which component has failed: replacing a relay, sensor, or seal is usually worth it, but replacing the compressor in an old Beko requires careful consideration. The start relay and sensors are wear parts — replacing them gets the appliance running again without opening the refrigerant circuit. The compressor is different: it's a sealed unit connected to the refrigerant lines, and replacing it means vacuuming and recharging the system. On older appliances, wear in other components adds to the cost. That's exactly why free diagnostics matter — to compare the scope of work with the condition of the appliance and avoid paying for repairs that don't make sense. The technician gives you the price after the inspection, and the decision is yours.

What to remember about Beko refrigerator repair

Here's what helps Beko owners quickly understand the cause of a breakdown and avoid paying for unnecessary work. Below are short takeaways on diagnostics and maintenance.

  • Compressor and start relay: if cooling is gone but the light is on, start by checking these two components, not the control board.
  • Blinking indicator: the signal points to the sensor circuit, not a specific broken part, so no diagnosis is made without measurements.
  • No Frost system: if there's ice in the freezer, check the defrost components first — the heating element, timer, and sensor.
  • Refrigerant leak or thermostat: the difference shows in how the compressor runs and the evaporator temperature when the motor is on.
  • Transport and door seal: after moving the appliance on its side, let it stand upright before plugging it in, and always match the seal to the exact model.

90brands

Besides Beko, we repair other refrigerator brands in Astana

We work with every brand sold in Kazakhstan — from Samsung, LG and Atlant to Biryusa, Indesit, Stinol and rare imported makes. Can’t find yours in the list? Call anyway — a technician will come and take a look.

We also repairWe also repairTECH SERVICE08

Besides Beko refrigerator repair, we fix other equipment in Astana

Tech Service technicians repair other appliances too — with the same 1-year warranty on labour and parts.

BlogBlogTECH SERVICE09

Worth reading before Beko refrigerator repair in Astana

Leave a review

Choose a platform — the TECH SERVICE page will open.

Send a review with photos on WhatsApp