Open until 19:00+7 (778) 046 88 53Call a technician
Tech Service technician next to a massage chair

Massage Chair Repair in Astana

A technician will arrive within 60 minutes anywhere in the city. Diagnostics are free.

  • 1-year warranty on labor and parts
  • 4 to 20 years of experience
  • Arrival within 60 minutes anywhere in the city

Our own technicians4 to 20 years of experience

Kairat A.Ruslan S.Nikita O.Kuanysh A.

Repair prices

  • Diagnostics0 ₸
  • Hand massager repairfrom2 500 ₸
  • Upholstery repairfrom4 000 ₸
  • Preventive maintenance (cleaning and lubrication)from4 500 ₸
  • Wiring restorationfrom5 500 ₸
All prices
ours5,06 127 reviews
order database
Common faultsCommon faultsTECH SERVICE02

Common massage chair faults in Astana

Below are eight typical symptoms and their likely causes. The technician will pinpoint the exact cause during diagnostics.

PricesPricesTECH SERVICE03

How much massage chair repair costs in Astana

The table lists the 'from' price for labor, for common jobs also the 'from' price of the part, plus the time required to complete the job.

Hand massager repairparts not included

1–3 hours

from2 500 ₸

Upholstery repairparts not included

1–3 hours

from4 000 ₸

Preventive maintenance (cleaning and lubrication)exact price — after the free diagnostics

1–2 hours

from4 500 ₸

Wiring restorationexact price — after the free diagnostics

1–2 days

from5 500 ₸

Sensor replacementparts not included

1–2 hours

from5 500 ₸

Before and afterBefore and afterTECH SERVICE04

Before and after massage chair repair in Astana

Backrest actuator failure

1 visittime

from 9,500 ₸cost

Problem
The backrest of the massage chair stopped reclining and was fixed in one position.
What we did
The technician removed the upholstery, replaced the failed backrest actuator, and checked the movement of the mechanism.
Result
The backrest reclines and locks again, the mechanism works smoothly; 1-year warranty on labor and parts.
I want the same
A gray massage recliner chair stands in a bright living room with sheer curtains and a wooden floor, with a bag on the floor nearby.BeforeAfter
01 / 03
All repairs
TECH SERVICE mobile technician with a tool case

How massage chair repair works at your home in Astana

Five steps from request to checking the chair after repair.

  1. Requeston the day of request

    Describe the symptom and chair model — the technician will prepare tools and parts.

  2. Preparing for the visitbefore the visit

    The technician checks the chair model and symptom from the request, and brings the necessary tools and common parts.

  3. Agreeing on the workafter inspection

    The technician lists the faults and offers options — repair the component, replace a part, or decline.

  4. Recording the resultafter checking

    The request notes which components were checked and what exactly needs attention.

  5. Phone clarificationbefore the visit

    The technician confirms the model, chair age, symptom, and access to a power outlet — without repeating diagnostic steps.

Leave a request

We reply during working hours

Book massage chair repair in Astana

The technician will help sort out an unclear symptom: the chair won't turn on, is noisy, or won't hold pressure. Have the chair model and a description of the problem ready for your request.

TECH SERVICE administrator replying to a customer's WhatsApp message

Warranty question? Call us

+7 (778) 046 88 53
Customer reviewsReviewsTECH SERVICE05

Reviews of massage chair repair in Astana

5,0ours

6 127 reviews of repairs at TECH SERVICE in total

Яна Э.Order No. AS-3582 · 22 February 2026

ours

Переезжали в новую квартиру, техника после перевозки захандрила. Открыл — и сразу понял: греется. Дома включил, всё на месте.

Repair: massage chair repair in

Ульяна Ч.Order No. 78694 · 25 December 2025

ours

Офис на Кабанбай батыра, технику туда и повёз. Симптом как на ладони: греется. Тихо, ровно, без сюрпризов.

Repair: massage chair repair in

Семён Ш.Order No. 25664 · 20 September 2025

ours

Заявку оставил через сайт вечером, утром перезвонили. Записался на ремонт массажёра. Жалоба одна: не вибрирует. Дамир М подобрал аналог дешевле, не навязывал оригинал. Обошлось заменой: двигатель. Приняли вечером, хотя до закрытия оставалось минут десять. Цену держали до конца, молодцы. Пользуюсь и вспоминаю добрым словом.

Repair: massage chair repair in

Борис В.Order No. ZK-2025-316 · 6 March 2025

ours

Хотел вызвать на дом, но в ЖК не пускают без пропуска. Приехал с дачи, а тут — не вибрирует. На ресепшене оформили за пару минут, выдали квитанцию. Вышло около 3 500, точнее не считал. Приговор — двигатель. После ремонта — как новое.

Repair: massage chair repair in

Фёдор Б.Order No. 87642 · 22 February 2025

ours

Раньше обращался в другой сервис, там очередь на две недели. Отдал в сервис: массажёр. Первое, что заметил: не вибрирует. Дамир М отсоветовал дорогой ремонт, предложил простой. Нужна была новая деталь: двигатель. Отдал 12 500 и не жалею. Не пришлось стоять в очереди, хотя народу было. Тихо, ровно, без сюрпризов

Repair: massage chair repair in

Эвелина Ш.Order No. AST-2503-211 · 7 February 2025

ours

Причина обращения — не вибрирует. Турарбек Кайрош провозился, но сделал. Функционирует, тьфу-тьфу.

Repair: massage chair repair in

Валерия А.Order No. AST-2506-909 · 2 February 2025

ours

Живу в Есиле, искал сервис, чтобы не тащиться через весь город. Думал, показалось, ан нет: греется. Турарбек Кайрош объяснял без умных слов, за это спасибо. Вышло из строя: двигатель. Привезли на такси, приняли без вопросов. По деньгам вышло ровно, без сюрпризов. Сейчас пашет без нареканий.

Repair: massage chair repair in

Оксана Т.Order No. 73917 · 22 January 2025

ours

С этим и пришёл: не вибрирует. Дамир М принял без вопросов, хотя был без записи. После ремонта — как новое.

Repair: massage chair repair in

Георгий З.Order No. ZK-2024-311 · 21 March 2024

ours

Знакомый мастер раньше здесь работал, дал номер. Было ощущение, что попал на замену целиком. Первое, что заметил: греется. Ни разу не пожалел)

Repair: massage chair repair in

Виолетта Д.Order No. ZK-2024-878 · 20 January 2024

ours

Основная жалоба — не вибрирует. Турарбек Кайрош разобрался в редкой модели. Астанинский Tech-service — нормальный вариант. Полёт нормальный)

Repair: massage chair repair in

Our technicians in Astana

01 / 08
Kairat A., senior small appliance technicianexperience14 years

Kairat A.

Senior small appliance technician

Ruslan S., on-site coffee machine diagnostics technicianexperience15 years

Ruslan S.

On-site coffee machine diagnostics technician

Nikita O., coffee machine cleaning technicianexperience5 years

Nikita O.

Coffee machine cleaning technician

Kuanysh A., coffee machine diagnostics technicianexperience12 years

Kuanysh A.

Coffee machine diagnostics technician

Aydar A., portafilter coffee machine technicianexperience5 years

Aydar A.

Portafilter coffee machine technician

Serikbay A., vacuum cleaner repair technicianexperience12 years

Serikbay A.

Vacuum cleaner repair technician

Artur G., vacuum cleaner repair technicianexperience15 years

Artur G.

Vacuum cleaner repair technician

Akzhol K., washing machine repair technicianexperience18 years

Akzhol K.

Washing machine repair technician

Questions and answersQuestionsTECH SERVICE06

Questions about massage chair repair in Astana

Didn’t find the answer? Message us on WhatsApp.

Ask a question
Can a massage chair be repaired at home in Astana, or does it have to be taken to a service center?

A technician can fix most issues on-site: electronics, remote control, wiring, compressor, and carriage mechanics. The chair needs to be taken to a service center if the frame is damaged or complex disassembly is required, and the technician decides this after inspection.

The massage chair turns on but the rollers don't move — is it the motor or the control board?

You can't tell for sure from the symptom alone: it could be the carriage motor, the board, or the position sensor, depending on the model. A free on-site diagnostic gives the exact answer, after which the technician names the cause and the cost of work.

Why is the massage chair humming and vibrating more than usual?

Most often it's worn bearings, loose fasteners, or a misaligned carriage, sometimes a foreign object in the mechanism. If the hum appeared suddenly and is accompanied by jerking, it's better not to use the chair until a technician inspects it.

Is it dangerous to keep using the massage chair if oil is leaking from it?

Yes, if oil or water leaks inside the housing, the electrical components suffer, and a slippery spot appears on the floor. The chair should be unplugged and a technician called to find the source of the leak and check the wiring.

What should I do if the massage chair won't turn on and the technician hasn't arrived yet?

Check that the plug is firmly in the socket and the power cord is intact, try another outlet. Don't disassemble the housing: before the technician arrives, it's enough to unplug the chair and leave it alone.

Can I fold the chair myself if the backrest is stuck in the reclined position?

Only try mechanical adjustment according to your model's instructions, without disassembling the housing or using force. If the recline mechanism is stuck, a technician repairs it: you can easily bend the rods and break the drive by doing it yourself.

Repair guideArticleTECH SERVICE07

Massage chair repair in Astana by Tech Service

Kairat A., senior small appliance technician

Author: Kairat A.,Senior small appliance technician

Published
Updated

Tech Service repairs massage chairs in Astana: our technician comes to your home within 60 minutes anywhere in the city or takes the chair to our service center. Diagnostics are free, we give you the price after diagnostics, and provide a 1-year warranty on labor and parts. Our technicians have 4 to 20 years of experience.

Why your massage chair stopped working and what to check before a technician repairs it

A symptom alone rarely points to a single component. We show you how the chair's behavior can narrow down the causes and what you can safely check before the technician arrives.

The chair won't turn on and doesn't respond to the remote

Most often the culprit is the power supply, control board, or remote signal receiver, not the massage mechanism itself. We start diagnostics by measuring the voltage at the power supply output: a drop under load or no voltage at the connector immediately rules out half the possibilities. Then we check the control board — bulging capacitors, signs of overheating on the traces, oxidation after power surges. We test the signal receiver separately: if the chair responds to buttons on the body but ignores the remote, the issue is in the infrared receiver or the remote itself, not the power section. Before calling a technician, check the outlet and the cord for kinks — that's the only safe check; don't dig into the board without diagnostics.

The chair hums but doesn't massage, and the backrest jams

Humming without roller movement usually means the carriage is jammed or the roller motor is worn out, and a jammed backrest points to position sensors or the actuator. These models use brushed electric motors, and when the brushes wear out, the motor hums but lacks power: the shaft spins freely while the roller mechanism stays put. The carriage jams on the guides when lubrication dries up or upholstery fabric gets into the rail. Position sensors detect the backrest and roller positions, and if the signal is lost, the board blocks movement — the chair hums but doesn't execute commands. The backrest recline mechanism with the actuator sticks when misaligned. If the chair is stuck in the reclined position, don't try to force it closed — that bends the gearbox, and instead of replacing a sensor you'll have to replace the entire mechanism.

The infrared zone doesn't heat and oil leaks

Lack of heating is often due to the heating element or its contacts, and an oil leak is related to the pneumatic system and compressor seals. We check the infrared heating element with a multimeter for resistance: a broken coil or burnt contact on the terminal causes a cold zone while the massage works. We also inspect the wiring harness to the backrest — with constant movement of the section, the insulation rubs through, and power doesn't reach the heater. In the pneumatic system, the compressor pumps air into the cushions, and over time the seals and hoses lose tightness — oil from the compressor seeps at the joints and under the upholstery. Tech Service services the entire pneumatic system: compressor, cushions, hoses. An oil leak isn't always dangerous, but you shouldn't ignore it — the fluid gets on the upholstery and wiring, so it's best to unplug the chair before the technician arrives.

What the error code on the display means and how to read the remote indicators during massage chair repair

An error code on the display is a hint, not a verdict. We explain what typical chair signals mean, how technicians read them, and where the do-it-yourself decoding ends.

How a technician reads the error code on the display

The error code points to a specific component — the control board, motor, sensor, or air system — and the technician matches it with how the chair behaves rather than relying on the numbers alone. Our specialists start by recreating the failure scenario: which mode the chair stopped in, whether the pump was humming, whether the backrest was moving. Then the number on the screen is checked against the code map for that specific model — control boards from different manufacturers use their own numbering, and the same digits describe different faults. Position sensors show where the mechanism got stuck, and the control board logs an overcurrent if the motor is working hard. Our technicians have 4 to 20 years of experience, and on models with two boards they first determine which one is the master. The same code can mean different things on different models, so the interpretation is checked against the specific model, not a generic table from the internet.

Remote indicators and button response

If the remote doesn't respond, the cause may be the remote itself, the signal receiver, or the control board, and only diagnostics can pinpoint the culprit. First check the batteries and re-pair the remote — that rules out half of false calls, but if the chair still doesn't respond, the issue is in the electronics. A blinking power indicator when you press a button means the command reaches the receiver but the board doesn't execute it. A steady light with no response to buttons usually points to a stuck key or a controller firmware failure. We replace the control board, remote, and signal receiver — each of these parts fails in its own way, and swapping one for another masks the real cause. Diagnostics are free, so the technician checks the electronics before quoting the cost of work.

When you can act on the error code yourself

  • Unplug the chair: pull the plug from the outlet and wait a couple of minutes to drain residual power from the board.
  • Write down the code: note the digits from the display and which mode the chair stopped in.
  • Describe the behavior: note whether the motor hums, the backrest moves, and the remote indicators blink.
  • Don't open the casing: opening the panel without a diagram shifts the position sensors and complicates further diagnostics.
  • Pass the data to the technician: with the recorded code and description, they bring the right parts and arrive prepared.

How massage chair repair works on-site and when it needs to go to the service center

A massage chair weighs tens of kilograms and won't fit through a doorway without disassembly, so the type of work depends on the component. Here's what a specialist handles on-site and what requires the workshop.

What the technician does on-site

On-site, we provide free diagnostics, agree on the work, and fix most issues — from the control board to the air system. The specialist checks the power, tests the remote and controller, inspects the air lines and guide rollers, then shows you the cause and the scope of work. Massage chair repair in Astana most often happens on-site, without transporting the casing. A 60-minute arrival across the city means the unit doesn't stay disassembled for long: the technician arrives prepared for the described symptom, with tools for the board, air system, and mechanics. Our experience shows that half of all calls are resolved on-site, without transporting the casing. Before the visit, describe exactly what's happening with the unit — based on that, the specialist brings the right parts and doesn't waste time on clarifications.

When the chair needs to go to the service center

We send the unit to the service center when major components need replacing or the mechanism requires complex disassembly that's hard to do in an apartment. The roller mechanism, backrest recline mechanism, and load-bearing frame need a stable platform, and in a living room there's no room to turn the body for access to the fasteners. At home or in the service center, the work is chosen based on the component, not the client's preference: we handle electronics, the remote, and the pneumatic system on-site, while major mechanical overhauls are moved to the workshop. The decision on the format is made after diagnostics, not in advance—often what seems like 'service center only' can be fixed on-site in one visit. So don't take the equipment apart or look for movers before the inspection: the specialist first identifies the cause, then determines the format of work.

How long the repair takes and how to book

  • Request and symptom: describe whether the unit won't turn on, a zone isn't heating, or oil is leaking—this determines the tool set.
  • Arrival within 60 minutes: the specialist comes anywhere in the city, and diagnostics at home are free.
  • Approval of work: before repair begins, you receive a list of components and the cost, quoted after diagnostics.
  • Checking the result: the unit is started under load, and all modes and heating are tested.
  • 1-year warranty: covers labor and parts, payment in any convenient way.

Which chair components we repair and replace

A massage chair consists of electronics, mechanics, and pneumatics. Here's what most often fails and what work we perform on each component.

Chair electronics and mechanics

Most often, the control board, roller motors, and backrest recline mechanism fail; position sensors fail less often. The board controls the electric motors, heating, and pneumatic system all at once, so its failure often masquerades as several components breaking at the same time. Roller motors wear out from constant load: their brushes and bearings wear down, and humming and jerking appear during movement. The backrest recline mechanism suffers from misaligned guides and play in the hinges—the backrest gets stuck or lowers unevenly. Position sensors throw off calibration, and the device stops at the wrong point, not bringing the rollers to the right zone. In our practice, restoring massage chairs in Astana most often comes down to these four components, not the body or upholstery. When you call, state exactly what's happening with the unit: this way the technician can select the part for the likely cause in advance.

Comparison of components by type of work

ComponentWhat we checkType of work
Control boardpower, signals to motorsdiagnostics, installation of a new element
Roller and recline motorsrotation, brush wearrestoration, installation of a new one
Pneumatic systemtightness, compressorrestoration, hose replacement
Heating elementheating, contactsinstallation of a new element
Upholstery and paddingwear, cutsrefurbishment separate from mechanics

Which brands of chairs we service

We service chairs from well-known brands, including Ogawa, Fujiiryoki, and Human Touch, as well as models with mechanical and electronic controls. Mechanical versions are simpler in design: there's less electronics, and therefore fewer components that can fail. Electronic ones are packed with boards, sensors, and pneumatic valves, so diagnostics require more attention. The brand affects parts availability: for some models, parts are found faster; for others, we have to look for compatible analogs. When you call, it's worth naming the model—this way the technician understands in advance what's needed for restoration. We also take on units whose manufacturer's warranty expired long ago: the age of the model is no reason to refuse service. Our technicians have 4 to 20 years of experience, and we already know the typical weak points for each brand.

Warranty, DIY repair limits, and your chair after the manufacturer's warranty

The fear of "I'll take it apart and break it for good" and the question "will they still cover it if I've already touched something" have the same answer — knowing where DIY territory ends and the technician's work begins.

What you can fix yourself and where you risk breaking the mechanism

  • Power and outlet: check that the plug sits firmly in the socket and the outlet works — this is the most common reason a chair "won't turn on."
  • Cord and power supply: inspect the cable along its entire length for kinks and signs of melting, without removing the cover or opening the housing.
  • Remote batteries: replace the batteries and check that the buttons don't stick or jam when pressed.
  • Error code: take a photo of the symbols on the display — it helps the technician quickly figure out which unit to check first.
  • Off-limits: don't touch the control board, gearbox, or recline mechanism — those need tools and a disassembly diagram.

What warranty covers the repair

We provide a 1-year warranty on labor and parts, and diagnostics before repair are free. A technician comes to your home anywhere in the city within 60 minutes so you don't have to haul a large chair across the apartment, and identifies the fault on the spot. The same term applies to replaced parts, so if the same unit fails again, you don't pay for the work twice. We accept payment via Kaspi QR, Kaspi Red (instalments), bank card, cash, or bank transfer for companies, and the technician quotes the price after the free diagnostics, once the cause is clear. In our experience, repeat calls for the same unit within a year are rare, and in each such case the work is done at no extra charge. The manufacturer's obligations on a new chair and our warranty on completed work are different things, and ours kicks in exactly when the former no longer covers the breakdown.

Your chair after the manufacturer's warranty

We service chairs with expired factory warranties just like any other — with free diagnostics and a one-year warranty on our work. Technicians with 4 to 20 years of experience handle both the mechanics and electronics of the chair, regardless of how many years it has been in use. If the factory warranty hasn't expired yet, it's best to go through that first, and come to us when it no longer applies. This approach saves the owner money: while the manufacturer's obligations are in effect, some faults are fixed under them, and paid service starts only after they end. For a chair that has long been out of production, we source compatible parts and test them on site before installation.

How to choose a service provider in Astana and what affects the price

The capital's market has plenty of middlemen, and who you contact affects timelines, warranty, and the final price. Let's break down how a direct provider differs from an aggregator and what goes into the bill for the work.

Direct provider or aggregator

Tech Service is a direct provider with its own technicians, not an aggregator or middleman, so the same service that does the work is responsible for it. Our specialists have 4 to 20 years of experience with chairs, come to your home or accept the equipment at the service center, and the workshop itself provides a 1-year warranty on labor and parts. An aggregator works differently: it passes the request to a third-party technician, adding an extra link in the chain. Because of that, you have to demand the warranty from a dispatcher rather than from the person who held the tools and took the mechanism apart. In my view, the difference shows up in a disputed situation — when a unit fails again a month later. With a middleman, the complaint gets forwarded to the contractor, and you have to explain all over again what broke and where. With a direct service, you talk to the same people who did the diagnostics and the repair — that saves time and nerves.

What affects the cost of work

The technician gives you the price after a free diagnostics, because it depends on the unit, the type of fault, and the part needed. The same symptom on two different chairs can cost differently: a stuck backrest might be caused by a position sensor, worn guide rollers, or the control board, while an oil leak could come from a hydraulic cylinder seal or a cracked hose. Until the technician opens the casing and checks the power circuit, it's impossible to give an exact price — any figure over the phone would be a guess. Diagnostics before work isn't about inflating the bill; it's about not replacing a working part instead of the broken one — that's where you save. In our experience, a common picture is when the owner has already bought a power supply "just in case," but the real cause was the remote. So we first find the faulty unit, then agree on the work.

Who this service is for and how to pay

This service is for owners of home and premium chairs with any malfunction, and you can pay via Kaspi QR, Kaspi Red, bank card, cash, or bank transfer for companies. The chair won't turn on, hums without massaging, the infrared zone doesn't heat, oil leaks, or an error code shows on the display — the technician has a specific inspection procedure for each of these situations. A visit within the city takes 60 minutes, diagnostics is free, so the inspection doesn't obligate you to any work. If the chair won't turn on at all, don't wait for it to "fix itself" — free diagnostics will show the cause, and you decide after that. Many put off calling because they fear a big bill, though in fact half of all requests end with a minor adjustment. Our advice: note down which unit the technician identifies as faulty — that will be useful for a warranty claim.

Getting massage chairs relaxed again

Summary on diagnostics and repair: what to remember before calling a technician or taking the chair apart yourself. We've briefly gathered the key points from all sections.

  • A symptom is not a diagnosis: a single sign only narrows down the possible causes, while the exact faulty unit is determined by the technician on site.
  • Error codes are read by model: remote indicators and display combinations are decoded according to the documentation for the specific chair, not a generic table.
  • Large units are usually serviced at home: a bulky chair is disassembled and serviced on site; it's sent to the service center only when major mechanisms need replacing.
  • Do it yourself only for safe checks: checking the power, remote, and noting the error code carry no risk, but it's better to leave disassembly of the mechanism to a specialist.
  • Three things decide your choice of provider: direct staff technicians with no middlemen, free diagnostics, and a 1-year warranty on labor and parts.

12brands

Which massage chair brands we repair in Astana

We source parts by chair model. See the list of brands with dedicated pages below.

We also repairWe also repairTECH SERVICE08

Besides massage chair repair, we fix other equipment in Astana

Tech Service technicians repair other appliances too — with the same 1-year warranty on labour and parts.

BlogBlogTECH SERVICE09

Worth reading before massage chair repair in Astana

Leave a review

Choose a platform — the TECH SERVICE page will open.

Send a review with photos on WhatsApp