Шынар М.Order No. TSA-32082 · 31 October 2026
oursАлдымен интернеттен қарадым, кейін осында келдім. Ескі бөлшекті көрсетіп, қайтарып берді. Қосымша жұмыс қажет болды, бірақ бағаны көтермеді. Жұмысты сол күні аяқтады. Рахмет, ұсынамын)
City
Language
What broke
Sections
Message on WhatsApp+7 (778) 096 59 61Mon–Fri 10:00–19:00, Sat–Sun 11:00–18:00
A technician arrives within 60 minutes anywhere in the city. Free diagnostics, 1-year warranty on labor and parts.
Our own technicians4 to 20 years of experience




Repair prices
Below are the symptoms customers most often report and their likely causes. The technician will determine the exact cause during diagnostics.
no power, faulty power supply
from4 000 ₸
damaged lens, settings reset
from12 500 ₸
memory card failure, firmware error
from9 000 ₸
dirty optics, line interference
from8 500 ₸
mechanism jammed, lens wear
from12 500 ₸
faulty battery, damaged connector
from4 000 ₸
dead clock battery, sync failure
from5 500 ₸
cracked housing, detached connector
from3 500 ₸
The table lists the 'from' price for labor, for common jobs also the 'from' price of the part, plus the time required to complete the job.
5 steps

From request to performance check — five steps.
Describe the symptom and camera model — the technician will prepare for the visit.
Agree on a convenient visit time and prepare access to the camera and recorder.
The technician will show part options for your camera model and explain the difference between them.
You approve the scope of work and the part, and only then does the repair begin.
The technician will confirm the model and firmware by phone to prepare the necessary tools.
We reply during working hours
Describe the problem — a technician will arrive within 60 minutes anywhere in the city. 1-year warranty on labor and parts.

Warranty question? Call us
+7 (778) 096 59 616 127 reviews of repairs at TECH SERVICE in total
Шынар М.Order No. TSA-32082 · 31 October 2026
oursАлдымен интернеттен қарадым, кейін осында келдім. Ескі бөлшекті көрсетіп, қайтарып берді. Қосымша жұмыс қажет болды, бірақ бағаны көтермеді. Жұмысты сол күні аяқтады. Рахмет, ұсынамын)
Людмила Щ.Order No. TSA-46613 · 28 August 2026
oursДамир М посмотрел и честно сказал: менять не надо. Вскрытие показало: аккумулятор. Прошивка та же, ничего не сбросили.
Ульяна Ч.Order No. 2604-7947 · 27 August 2026
oursСосед по площадке хвалил, решил проверить. Сначала списал на мороз, но нет: дрожит картинка. Привезли на такси, приняли без вопросов. Приговор — привод. Сказали 22 000 по телефону, столько и вышло. Ни шума, ни запаха, всё штатно.
Леонид П.Order No. ZK-2026-311 · 22 June 2026
oursЗимой без техники никак, поэтому тянуть было нельзя. Жалоба одна: разбит экран. Дома включил, всё на месте
Степан Я.Order No. 2608-8538 · 8 June 2026
oursСимптом как на ладони: сломался экран. Максим Снегирев отсоветовал дорогой ремонт, предложил простой. Проверил на всех режимах — держит.
Аркадий Я.Order No. 59963 · 26 March 2026
oursЖиву в Есиле, искал сервис, чтобы не тащиться через весь город. Сначала списал на мороз, но нет: дрожит картинка. Настройки не слетели, всё как было.
Даниял С.Order No. TSA-67519 · 8 February 2026
oursЖұмыстан кейін баруға болатын жер іздедім. Қабылдау тез болды, кезек жоқ. Қайта жүгінуден тартынбаймын)
Михаил У.Order No. 82447 · 8 December 2025
oursБольше всего мешало: не включается. Максим Снегирев разрулил всё быстро. Дома включил, всё на месте)
Вадим Г.Order No. ZK-2025-793 · 12 November 2025
oursВыбирал между официальным и этим, выбрал этот. С чем обратился: не держит ось. Полёт нормальный)
Валентина Р.Order No. AST-2511-279 · 24 October 2025
oursХотел вызвать на дом, но в ЖК не пускают без пропуска. Нужен был ремонт стабилизатора для камеры. Больше всего мешало: не держит ось. Приняли вечером, хотя до закрытия оставалось минут десять. В другом месте просили на треть больше. Обошлось заменой: плата. Третий месяц — никаких проблем.
Юрий М.Order No. 2509-2941 · 14 September 2025
oursБыло важно успеть до конца недели, а то морозы обещали. После скачка напряжения — сломался экран. Сейчас пашет без нареканий!!
Амир Р.Order No. ZK-2025-773 · 13 September 2025
oursДосым осы сервисті ұсынды, сеніммен келдім. Күтуге уақытым аз еді, сол күні бітірді. Кезекте аздап отырдым.
Сая Ф.Order No. ZK-2025-920 · 9 September 2025
oursКүтуге уақытым аз еді, сол күні бітірді. Қайта жүгінуден тартынбаймын)
Зоя М.Order No. TSA-79915 · 5 September 2025
oursИскал, кто работает в субботу, у нас с женой график сложный. Основная жалоба — не включаеться. Работает, даже лучше прежнего.
Фёдор Б.Order No. AS-2210 · 19 July 2025
oursОсновная жалоба — не пишет. Максим Снегирев объяснял без умных слов, за это спасибо. Пользуюсь и вспоминаю добрым словом.
Юрий М.Order No. 41092 · 13 July 2025
oursПозвонил в четыре места, тут ответили по-человечески. Нужен был ремонт стабилизатора для камеры. С чем обратился: не держит ось. Выбирал по карте, Tech-service был ближе всех. Ни шума, ни запаха, всё штатно.
Степан Я.Order No. AST-2501-499 · 26 June 2025
oursДамир М разобрался в редкой модели. Тихо, ровно, без сюрпризов. Дома включил, всё на месте.
Ярослав С.Order No. AS-8903 · 23 June 2025
oursЗимой без техники никак, поэтому тянуть было нельзя. Уже представлял, как объясняю домашним, что техника всё. Симптом как на ладони: не держит ось. Максим Снегирев разрулил всё быстро. Третий месяц — никаких проблем.
Шынар М.Order No. 18234 · 11 April 2025
oursЖұмыстан кейін баруға болатын жер іздедім. Қабылдау тез болды, кезек жоқ. Бәрі жақсы болды.
Надежда Ц.Order No. AS-9662 · 25 March 2025
oursБыло важно успеть до конца недели, а то морозы обещали. Позвонил насчёт стабилизатора для камеры. Больше всего мешало: дёргается. Оплату взяли после ремонта, а не вперёд. Итог — 29 000 тенге, ничего сверху. Вскрытие показало: плата. Полёт нормальный.
experience7 yearsPC and network repair engineer
experience11 yearsSenior mobile computer technician
experience10 yearsLaptop repair technician
experience9 yearsMotherboard repair technician
experience16 yearsPrinter repair technician
experience12 yearsComputer repair technician
experience18 yearsAll-in-one computer repair technician
Didn’t find the answer? Message us on WhatsApp.
Ask a questionIn most cases, an IP camera can be repaired: fixing the board, power connector, or lens costs less than a new model. Replacement makes more sense if the sensor or processor is burned out — the technician will tell you after free diagnostics.
Test the camera with a known working power supply and a different cable — if the image appears, the issue is in the wiring. If there's still no signal, the camera itself is faulty, and it's worth showing it to a technician.
Usually the IR illumination is to blame: the LEDs have burned out, the ribbon cable has come loose, or the sensitivity settings are off. It depends on the model, but most often the illumination or its board is replaced, and the camera sees in the dark again.
Yes, laptop webcams can be repaired: often the issue is the ribbon cable, connector, or the module's sensor itself. The technician will check the connection and replace the faulty component if needed.
There's a chance if you don't charge or turn it on right away: corrosion is removed from the board at the service center. The outcome depends on the model and how deeply moisture got inside, so diagnostics are needed.
Yes, we accept such cameras for repair: we restore power, connectors, sensors, and mounts. A technician comes to your home anywhere in the city within 60 minutes, and diagnostics are free.
Tech Service repairs video cameras in Astana at your home or in our service center: a technician arrives within 60 minutes anywhere in the city, diagnostics are free, and you get a 1-year warranty on labor and parts. We take CCTV, IP, web, action cameras, dashcam cameras, and rear-view cameras. The technician gives you the price after diagnostics.
Video camera repair in Astana is not just about CCTV systems. Below we list the range of devices we accept and immediately answer the question "will you take my camera?".
We service outdoor and indoor CCTV devices and IP models, including Hikvision, Dahua, HiWatch, EZVIZ, and Xiaomi. During the work we check the sensor, lens, power supply, cable, and Wi-Fi module — the condition of these components determines whether an image appears and whether it reaches the recorder. For outdoor housings, we additionally check sealing: gaskets and IR illumination are the first to react to temperature changes and precipitation. We test network models separately over the network: the module may lose connection with the router even when the optics are fine. Diagnostics are free, a technician arrives on-site within 60 minutes anywhere in the city, and we give a 1-year warranty on labor and parts. If the device turns on but there is no picture, the sensor is often not to blame — it's usually the power or the line, so on-site we first test the wiring, not the optics.
We accept web models for PCs and laptops, action devices, as well as dashcam and rear-view equipment. Webcams most often suffer from a damaged USB connector and ribbon cable, action cameras from board issues, housing sealing, and battery problems, and car cameras from a wire at the bend point, connector, and memory card slot. Such breakdowns require different approaches: sometimes replacing the ribbon cable is enough, sometimes board soldering under a microscope is needed. A technician arrives on-site within 60 minutes anywhere in the city, or the device is serviced in our center, diagnostics are free, and payment is by any convenient method. After an action camera has been in water, it's important not to turn it on to check — attempting to power it up finishes off the board, and irreversibly oxidized contacts can no longer be restored.
| Device category | What we check first | Common cause of failure |
|---|---|---|
| CCTV cameras | Power, cable, IR illumination, sealing | Moisture, contact oxidation |
| IP cameras | Network, Wi-Fi module, board, firmware | Firmware failure, power surge |
| Webcams | Connector, ribbon cable, driver, sensor | Ribbon cable wear, connector damage |
| Action cameras | Board, sealing, battery | Moisture, drop |
| Dashcam cameras | Cable, connector, memory card | Cable break, slot wear |
| Rear-view cameras | Cable, sealing, sensor | Moisture, cable break |
We explain why a camera stops showing an image, won't connect to the network, or can't see at night — and what technical cause is behind it.
A black screen or "no signal" usually points to a power, cable, or matrix issue rather than a complete device failure. Over time, the power supply drops voltage, oxidized connectors lose contact, and a pinched or broken wire at a bend stops transmitting the signal to the recorder. The matrix fails less often—typically after a voltage spike or overheating in the sun. It's easy to check: if the device heats up and the IR filter clicks when powered on, the board is alive, and the problem lies in the line or the light-sensitive sensor. Start by swapping the power supply with a known working one and test the wire along its entire length: this eliminates half the causes before you even open the case. Such a check takes just a few minutes and requires no special tools beyond a multimeter.
"Network error" and failure to connect to the recorder are usually related to the Wi-Fi module, settings, or a firmware glitch. The module loses sensitivity after overheating or a lightning strike, incorrect parameters don't match the recorder's subnet, and a failed firmware update leaves the device stuck in a reboot loop. Another cause is an IP address conflict, when two devices on the same network are assigned the same address. Before replacing the module, reset the camera to factory settings and reflash—some "dead" modules come back to life after this. If after reset the device appears in the list of available connections but won't hold the connection, check the signal level: weak Wi-Fi at a far wall is fixed by moving the access point, not by repair. You don't need to touch the network settings in the recorder.
At night the device "goes blind" due to IR illumination failure, and internal fogging is a sign of broken case sealing. The IR LEDs degrade over time, the IR module driver burns out during a voltage spike, and the mechanical IR filter sticks and doesn't switch to night mode. Moisture gets inside through a dried-out lens seal or a crack in the case, and condensation settles on the matrix and lenses. It's pointless to just wipe the fogged case from the outside—condensation inside will return until sealing is restored and moisture is removed from the board. When replacing the seal, ask the technician to also check the case for microcracks: without this, a new gasket won't keep moisture out during temperature changes. After moisture exposure, the board is additionally dried and inspected for corrosion—oxides eventually eat away traces and contacts.
We show the camera's journey from request to pickup: what the specialist does at each stage and where you decide on further work.
Diagnostics are free with us, and the technician quotes the cost of work after diagnostics—before starting. First, they check the power, cable, and connector, then connect the device to a test recorder and look at the image on the monitor: is there a picture, does the IR illumination work, does the device respond to network requests. Separately, they test the ribbon cable and inspect the board for swollen capacitors and signs of moisture. Based on the inspection, you get a clear picture—which component failed and what work is needed. Approval before work starts protects you from surprises: if after disassembly another component is needed, the specialist will approve the scope again rather than adding it silently. Often at this stage, it's enough for the person to know the cause and decide whether to repair or replace the device.
A technician arrives at your home within 60 minutes anywhere in the city and handles on-site whatever doesn't require removing the device; the rest is done at the service center. During the visit, typical tasks are covered: network and recorder setup, power supply replacement, connector resoldering, firmware reflashing. If board soldering, matrix or lens replacement is needed, the device is taken to the workshop — there the work is done with the case opened and every component checked. The on-site specialist records the initial condition of the equipment so you can compare the result upon pickup. What exactly needs to be done and to what extent — the technician explains after diagnostics, rather than making blind promises in advance. Moreover, for outdoor models, the case seal is checked separately: after lens replacement, the gasket is reinstalled, otherwise condensation will return on the very first cold night.
We provide a 1-year warranty on labor and parts and you can pay via Kaspi QR, Kaspi Red (instalments), bank card, cash, or bank transfer for companies. It covers both on-site visits and workshop repairs — no matter where the issue was fixed. Before payment, the specialist shows the image on the monitor, checks the recording and backlight — you see the result of the work. We accept cash, cards, and transfers — whatever is convenient. The warranty on components is just as important as on labor: if a replaced component fails six months later, it's a warranty case, not a new service at your expense. That's why upon pickup the technician specifies which component was replaced — this makes it easier to claim the warranty if the component fails again. If the same breakdown recurs within this period, we cover the repeat work and part under warranty, at no extra charge.
We separate the work: some faults the technician fixes right on the spot, while others require removing the device and disassembling it at the workshop. Below — which tasks are handled on-site, which only at the workbench, and how to choose the format for your situation.
At your home we set up the camera, replace the power supply, restore the cable and connection to the recorder or Wi-Fi. On-site tasks that don't require opening the case include: checking the power line with a multimeter, re-crimping the connector, reflashing the communication module, re-registering the device in the recorder or router, adjusting the angle and detection zone. The technician arrives anywhere in the city within 60 minutes, diagnostics are free, so the cause of the failure is clarified on the spot without transporting the equipment. An on-site visit saves not only time: removed equipment still needs to be properly dismantled and reinstalled, and a mistake during installation of an outdoor model breaks the seal again — and moisture gets inside the case. It's easier to fix the issue where the device is already mounted and working.
Matrix replacement, board repair, and case sealing are done at the workshop, where the device can be disassembled, dried, and tested under load. At the workbench, the sensor is replaced, components are soldered after a voltage surge, the case is cleaned and resealed after internal fogging, and the IR backlight board is serviced. We provide a 1-year warranty on labor and parts — this also applies to replaced components. The matrix is replaced only after checking the entire line: sometimes a 'dead' sensor is actually fine, and the signal is lost on the cable or connector, in which case replacing the part would be an unnecessary expense. Such work requires access to internal components and stable conditions that can't be created on-site. That's why the technician first removes the device, records its initial condition, and only then starts disassembly at the workshop — this makes it easier to check every component and avoid damaging the case during removal.
| What happened | Where we fix it | Why |
|---|---|---|
| Won't turn on, no power | At your home | Power supply or line is replaced |
| "Network error", no connection | At your home | Setup, reflashing, Wi-Fi module |
| No image, black screen | At your home or in the service center | We check the line first, then the sensor |
| Fogging, blurry picture | In the service center | Requires disassembly and drying |
| IR illumination not working | In the service center | Requires access to the illumination board |
| Board damaged after a power surge | In the service center | Requires component-level repair |
We help you decide when it's more cost-effective to repair the device and when replacement is justified: we look at the nature of the fault, the age of the equipment, and compatibility with your surveillance system.
Restoration makes sense when a single component has failed—power supply, cable, connector, or IR illumination—while the sensor and board are intact. Our technician checks each element in turn during the visit: tests the power line for continuity, inspects the connector contacts, and tests the infrared diodes in the dark. Most often the power supply fails—it runs under constant load and is the first to take power surges. Outdoor cable suffers from frost and UV, the connector oxidizes from moisture, and IR illumination burns out after a few seasons. If diagnostics show that only one part needs replacing, the device continues to work in the existing system without reconfiguring other devices. Replacing one component often solves the problem—there's no reason to throw away a device with a working sensor and board. A Tech Service technician gives the price for such work right at the approval stage.
Replacement is smarter when both the board and the sensor are damaged at the same time—for example, after a strong power surge or water ingress. A power surge takes out the power supply and the device board at once: the input circuit burns out, and then the signal processing processor goes with it. Moisture acts more slowly—oxidation eats away the board traces, and the device stops turning on weeks after the rain. If two key components are dead, restoration requires microchip-level soldering, and the outcome isn't always predictable. Even in this case, it's worth getting a diagnostic conclusion first: sometimes a "hopeless" device comes back to life after replacing one board component. The technician opens the case, checks the power circuits, and only then says whether restoration is worth pursuing.
A 1-year warranty covers both the work and the installed parts, and a direct contractor is responsible for the entire job. Let's break down exactly what this period covers and how to tell a service center from a middleman.
The 1-year warranty covers both the technician's work and the parts installed. If the image disappears again after the camera service or the power module fails, you go back to the same technician who did the work — no back-and-forth with a platform or searching for a new contractor. With us, this term is the same for on-site visits and in-shop work: equipment repaired at home is serviced under the same conditions as equipment brought to the workshop. Devices last longest when the cause is fixed, not just the symptom: if you replaced a burnt-out power supply, check the cable and connectors too. The parts commitment is what sets direct service apart from an intermediary: an aggregator only guarantees that it found a technician, not the part.
Tech Service is a direct provider: our technician comes to you, not an intermediary who passes the request to a third party. The request doesn't go through a chain of platform — dispatcher — contractor, so you discuss terms and guarantees with the person holding the tools — no back-and-forth between links and no extra approvals. For on-site visits in the city, the technician arrives within 60 minutes, and you can pay via Kaspi QR, Kaspi Red, bank card, cash or bank transfer for companies — cash, card, transfer. With an aggregator, responsibility is blurred between the platform and the contractor: if the problem comes back, the platform points to the technician, and the technician points to the platform, leaving the customer stuck in the middle. Practical tip: confirm the provider and their obligations in the request in advance. That's why people turn to direct service after a bad experience with an intermediary. When the work and the guarantees are in the same hands, there's someone to hold accountable.
We've summed up our experience from on-site visits and in-shop repairs in a short summary: what breaks most often, where the line is between on-site and in-shop service, and what to look for when choosing a provider.
23brands
Choose a brand to go to the page describing service and common issues.
Tech Service technicians repair other appliances too — with the same 1-year warranty on labour and parts.
Refrigerator Repair in Almatyfrom 3 000 ₸
Washing Machine Repair in Almatyfrom 3 000 ₸
Dishwasher Repair in Almatyfrom 3 500 ₸
Oven Repair in Almatyfrom 3 000 ₸
Cooktop Repair in Almatyfrom 3 500 ₸
Air Conditioner Repair in Almatyfrom 3 500 ₸
Boiler and Water Heater Repair in Almatyfrom 2 500 ₸
Freezer Repair in Almatyfrom 6 000 ₸
Tumble Dryer Repair in Almatyfrom 5 000 ₸
Coffee Machine Repair in Almatyfrom 2 500 ₸
Robot Vacuum Cleaner Repair in Almatyfrom 3 500 ₸
Vacuum Cleaner Repair in Almatyfrom 1 500 ₸
Microwave Oven Repair in Almatyfrom 2 000 ₸
Hair Dryer Repair in Almatyfrom 1 500 ₸
Iron Repair in Almatyfrom 3 000 ₸
Electric Kettle Repair in Almatyfrom 2 500 ₸
Mixer Repair in Almatyfrom 2 500 ₸
Multicooker Repair in Almatyfrom 500 ₸
If your laptop screen is broken, turn the device off first, don't press on the display, and check the picture through an external monitor.
12 March 2026 · 11 minutes read
If your laptop freezes, the first thing to do is restart it and check Task Manager to see what's loading the CPU and memory.
25 January 2026 · 12 minutes read
If your computer won't turn on, start simple: check the outlet, power cable, switch on the power supply, and the power button.
19 January 2026 · 13 minutes read
If your laptop won't boot, first determine which of two states you're in: the device doesn't respond to the power button at all…
13 December 2025 · 12 minutes read












