Мерей Р.Order No. AST-2611-630 · 16 June 2026
oursҚұрылғы ескі, бірақ жақсы қарайды екен. Бағаны алдын ала айтты, соңында өзгермеді. Екі күннен кейін өзі қоңырау шалды. Мастер бәрін түсіндірді. Бәрі жақсы болды.
City
Language
What broke
Sections
Message on WhatsApp+7 (778) 096 59 61Mon–Fri 10:00–19:00, Sat–Sun 11:00–18:00
A technician arrives within 60 minutes anywhere in the city. Free diagnostics, technicians with 4 to 20 years of experience.
Our own technicians4 to 20 years of experience




Repair prices
Below are typical symptoms, their likely causes, and the cost of the technician's work. Free diagnostics will pinpoint the exact cause.
power, lamp, board
from7 500 ₸
bearing wear, dust, mounting
from5 500 ₸
optics, matrix, dust on the lens
from6 000 ₸
IR receiver, batteries, buttons
from3 500 ₸
clogged filter, dust in cooling
from2 500 ₸
connector, cable, board
from9 500 ₸
mechanism, motor, lens
from7 000 ₸
speaker, amplifier, settings
from9 500 ₸
Choose a tab by symptom — the table shows the cost of the technician's work for each service.
1–2 daystime
from 7 500 ₸cost

BeforeAfter5 steps

From request to final check — five clear steps.
The technician notes external signs: dust, overheating marks, condition of cables and connectors.
A technician arrives within 60 minutes anywhere in the city, bringing testing equipment.
The technician explains replacement options and what to check for model compatibility.
You approve the scope and price, then the technician starts the repair and parts replacement.
The technician demonstrates image and sound; check for clarity, colors, and absence of noise yourself.
We reply during working hours
Provide the model and symptom — the technician will prepare tools in advance and confirm details by phone.

Warranty question? Call us
+7 (778) 096 59 616 127 reviews of repairs at TECH SERVICE in total
Мерей Р.Order No. AST-2611-630 · 16 June 2026
oursҚұрылғы ескі, бірақ жақсы қарайды екен. Бағаны алдын ала айтты, соңында өзгермеді. Екі күннен кейін өзі қоңырау шалды. Мастер бәрін түсіндірді. Бәрі жақсы болды.
Айша О.Order No. AST-2604-925 · 12 January 2026
oursКеңседегі құрылғы, чек пен акт керек еді. Құрылғыны әкелдім, бірден қабылдады
Нурсултан Т.Order No. AST-2505-968 · 14 June 2025
oursТаңертең қоңырау шалдым, түске дейін апардым. Бағаны бірден айтпады. Достарыма айтамын.
Регина Ф.Order No. AST-2503-107 · 3 January 2025
oursЖиву в Есиле, искал сервис, чтобы не тащиться через весь город. Была мысль починить самому, но руки не дошли. Основная жалоба — сбилась фокусировка. Сергей Архипов не пропал после ремонта, помог с настройкой. Вытащили и показали: лампа. После ремонта — как новое.
Елизавета Л.Order No. ZK-2023-102 · 8 August 2023
oursИскал, кто роботает в субботу, у нас с женой график сложный. В работе было: проектор. Больше всего мешало: сбилась фокусировка. Дамир М всё сделал при мне, за пятнадцать минут. Замена: блок питания. После ремонта — как новое.
Альбина Ю.Order No. AST-2306-990 · 12 July 2023
oursОсновная жалоба — сбилась фокусировка. Сергей Архипов не пропал после ремонта, помог с настройкой. Работает, даже лучше прежнего)
Наталия С.Order No. AST-2302-309 · 29 April 2023
oursЖиву в Есиле, искал сервис, чтобы не тащиться через весь город. Разозлился, конечно. Вещь не старая. Причина обращения — тускнеет картинка. Сергей Архипов объяснял без умных слов, за это спасибо. Мастер сам предложил забрать технику на следующий день. Вскрытие показало: лампа. Сравнивал — здесь дешевле. Достойно сделали. Настройки не слетели, всё как было.
Екатерина К.Order No. AST-2308-859 · 28 March 2023
oursПервое, что заметил: тускнеет картинка. Дамир М посмотрел и честно сказал: менять не надо. Дома включил, всё на месте.
Салтанат К.Order No. AS-1712 · 4 December 2022
oursҚабылдау тез болды, кезек жоқ. Бөлшек қоймада бар екен, күтпедік. Қайта жүгінуден тартынбаймын.
Мария Р.Order No. 97419 · 12 September 2022
oursСимптом как на ладони: не включается. Сергей Архипов принял без вопросов, хотя был без записи. Вернули — проверил, всё ок.
Семён Ш.Order No. ZK-2022-768 · 12 July 2022
oursВ Астане с сервисами беда, поэтому выбирал по отзывам. С чем обратился: тускнеет картинка. Дамир М разрулил всё быстро. Функционирует, тьфу-тьфу.
Григорий И.Order No. AS-6484 · 10 June 2022
oursЖалоба одна: шумит. Сергей Архипов принял без вопросов, хотя был без записи. Полёт нормальный)
Вадим Г.Order No. 90103 · 31 December 2021
oursТехника на балансе ТОО, нужен был чек и акт. Проблема ровно одна: шумит. Внешне не видно, что разбирали.
Жамиля В.Order No. AS-8843 · 1 December 2021
oursАстанада тұрамын, қаланың арғы жағына бару ыңғайсыз болды. Таңертең қоңырау шалдым, түске дейін апардым.
Анастасия Т.Order No. TSA-80890 · 24 August 2021
oursПереезжали в новую квартиру, техника после перевозки захандрила. Больше всего мешало: сбилась фокусировка. Полёт нормальный.
Надежда Ц.Order No. AS-6739 · 25 July 2019
oursПозвонил в четыре места, тут ответили по-человечески. Сначала списал на мороз, но нет: тускнеет картинка. Сравнивал — здесь дешевле. Обошлось заменой: вентилятор. Позвонил, объяснил, сказали подъезжать — примут без записи. Вернусь при необходимости. Проверил на всех режимах — держит
Леонид П.Order No. 1909-2825 · 3 July 2019
oursПереезжали в новую квартиру, техника после перевозки захандрила. С этим и пришёл: тускнеет картинка. Ни шума, ни запаха, всё штатно.
Екатерина К.Order No. TSA-17767 · 20 June 2019
oursЖиву в Есиле, искал сервис, чтобы не тащиться через весь город. Скепсис был, признаю. Первое, что заметил: тускнеет картинка. Ни копейки больше обещаного. Замена: вентилятор. Диагностику провели при мне, ничего не унесли в подсобку. Советую. Полёт нормальный.
Маргарита П.Order No. AS-8603 · 26 May 2019
oursСергей Архипов разобрался в редкой модели. Вышло около 10 000, точнее не считал. Ни разу не пожалел)
Эдуард К.Order No. AS-7775 · 8 May 2019
oursЗнакомый мастер раньше здесь работал, дал номер. Открыл — и сразу понял: сбилась фокусировка. Сергей Архипов не пропал после ремонта, помог с настройкой. Пришлось ставить: лампа. Все функции проверил — работают.
experience7 yearsPC and network repair engineer
experience11 yearsSenior mobile computer technician
experience10 yearsLaptop repair technician
experience9 yearsMotherboard repair technician
experience16 yearsPrinter repair technician
experience12 yearsComputer repair technician
experience18 yearsAll-in-one computer repair technician
Didn’t find the answer? Message us on WhatsApp.
Ask a questionMake sure the outlet works and the power cable is firmly plugged in, and try a different cord. If the indicator light doesn't come on, there's no way to check further without taking it apart — you need a technician.
The technician can do some of the work on site, but for in-depth diagnostics a ceiling-mounted projector sometimes has to be taken off its mount. The decision is made after inspection and depends on the model and the nature of the problem.
Most often it's a worn fan bearing or dust buildup inside that makes the cooling system work at its limit. Cleaning and replacing the fan bring the noise level back to normal.
Yes, we accept Epson, BenQ, Acer, Xiaomi and other projectors, including those bought outside Kazakhstan. The scope of work depends on the model, and diagnostics are free.
Yes, in most lamp-based projectors the lamp is replaced separately from the power supply, depending on the model. The technician will first make sure the cause is the lamp and not the power supply.
Check whether the focus wheel has been knocked out of position and whether the lens is clean. If adjusting doesn't help, the lens mechanism is probably broken — a technician will inspect it.
Tech Service repairs projectors in Astana as a direct contractor: our technician comes to your home within 60 minutes anywhere in the city, or the work is done at our service center. Diagnostics are free, we provide a 1-year warranty on labor and parts, and our technicians have 4 to 20 years of experience.
Projectors fail in a few typical ways, and the symptom often already tells you which component to check first. Here are the most common causes people come to us with.
When our technician arrives, the first thing they check is the power circuit — the cable, the connector, and the power supply — because "won't turn on" most often means a failure in this area, not a dead control board. The power cable wears out near the plug, and the connector on the case loosens from frequent plugging and moving. The power supply is responsible for starting the device: it converts mains voltage into the operating voltage for the lamp and electronics, and if it fails, the device stays silent even with a working button. The remote is checked separately — sometimes the device works but doesn't respond to the infrared signal due to dead batteries or a stuck button. If the standby indicator is on but there's no startup, the issue is usually in the control board or the light source itself — this is already visible during free diagnostics, before disassembling the case.
For us, overheating almost always comes down to a clogged dust filter and cooling fan — the device dissipates heat poorly, the protection kicks in, and it shuts down after a few minutes of operation. The dust filter clogs within a few months of use in an apartment and noticeably faster in rooms near a road where the air is dustier. The cooling fan removes heat from the lamp and matrix: if the blades get covered in dust or the bearing seizes, the speed drops and the case overheats. A lamp at the end of its life runs hotter than a new one, so the protection triggers earlier. Cleaning dust and servicing the air ducts solves the problem before it reaches the lamp and matrix, so it's not worth delaying even if the device is still working.
"No signal" isn't always a breakdown: first check the source, cable, and selected input, and only if there's no picture from any device do you look at the HDMI connector and board. A laptop as a signal source often outputs the image to its own screen rather than an external one, so the device honestly reports no signal — switching the output mode solves it without calling a technician. The cable suffers from bends near the plug, and the HDMI connector on the case suffers from frequent connections: the contacts inside loosen, and the signal drops at the slightest movement of the wire. On older models, the VGA input gives the same picture with bent pins in the connector. The HDMI connector suffers from frequent connections and cable bends, so signal diagnostics start with the connector itself, not with expensive components.
When there's an image but the quality isn't satisfactory, it's important to understand where the failure is — in the light source, matrix, or optics. This determines which component is replaced and cleaned.
For us, a dim image most often points to wear of the lamp or LED module — the light source loses brightness and the picture turns gray. In lamp-based models, the projector lamp's life decreases gradually: over hundreds of hours the filament and reflector burn out, light output drops, and a dark ring appears at the edges of the frame. In LED modules, the crystals and power driver degrade; in laser sources, the laser block and cooling. Our technicians with 4 to 20 years of experience first measure brightness and check the optics rather than replacing a component blindly. Replacing the lamp restores brightness, but if the optics and air ducts aren't cleaned at the same time, the new lamp will quickly hit the same overheating.
Color spots and stripes usually come from the matrix or DLP chip, not the lamp — the light source handles brightness, while the matrix creates the image and color. In LCD projectors, these are three liquid crystal panels; in DLP, a micromirror chip with a color wheel. Dust on the lens causes uniform haze, but localized green or purple spots indicate burned-out panel pixels or stuck micromirrors. Stripes across the frame appear when the ribbon cable between the matrix and control board fails. If the spots "float" as the projector warms up, that's a sign of matrix degradation, not dust on the lens, and cleaning the optics won't help. For diagnostics, just display a solid gray background: it shows exactly where the layer is damaged.
A blurry image that won't come into focus is usually related to the optics and focus ring, not the projector's electronics. The focus ring adjusts image sharpness by moving the lenses inside the lens assembly: when the guides wear out or alignment is off, the movement becomes uneven and focus doesn't hold. A dirty or misaligned lens gives the same "soft" picture as a misadjusted focus, so the optics are checked before replacing components. On a ceiling-mounted projector, blurriness is often caused by the housing being tilted — realigning without disassembly usually fixes it. If sharpness fades ten minutes after turning on, the cause is thermal expansion of the lenses, and adjusting the ring alone won't solve it. The technician also inspects the lenses against the light — micro-scratches and film cause a persistent haze that can't be fixed with settings.
Taking down a ceiling-mounted projector is inconvenient, so whether the technician comes to you or picks it up is a deciding factor for many — we break down both options and explain which component is serviced where.
We arrive at your home within 60 minutes anywhere in the city and service projectors mounted on the ceiling — the technician removes and checks them on site, without transporting them to the shop. During the visit, we clean the optics and filters, replace the lamp, check HDMI cables and connectors, adjust focus, and diagnose the control board using error codes. The mount stays on the ceiling: only the projector body is removed, and we inspect the mounting screws and bracket for play — it often causes image tilt. In Astana, in-home visits resolve most calls about overheating and a dim picture, where the culprit is dust-clogged optics rather than electronics. This kind of projector repair in Astana at home saves more than time: removal and transport are the most common cause of damage to the mount and optics.
Some work is done in our shop — when disassembly down to the board or matrix replacement is needed, it's better to bring the projector in, and the technician will tell you after free diagnostics. It doesn't make sense to open the sealed optical block, replace the matrix, or solder the power circuit at home: that requires a lit workbench and dust protection, otherwise particles will remain on the new matrix and cause those very spots. In the shop, we do a thorough cleaning of the light tunnel and alignment after replacing components. The decision "home or shop" is made based on the component, not the model: cleaning and lamp replacement are often done on site, while deep board work is done in the shop. So before the visit, ask the technician what exactly they'll check on site — it will save you a second trip.
When you need a projector for a presentation or meeting, every hour counts — here's how a technician visit works and what happens during the check before the device is taken apart.
Our technician arrives within 60 minutes anywhere in the city, so urgent projector repair before a presentation doesn't turn into waiting for days. Tech Service works as a direct provider: our own employee comes to you, not an intermediary who passes the request to a third party. Placing a request takes a few minutes: just describe how the device behaves — won't turn on, turns off after a couple of minutes, doesn't see the signal source. We plan the route to cover any district of Astana, including new residential areas on the left bank, not just central neighborhoods. Urgency doesn't cancel the check: we first determine the cause instead of randomly replacing parts, otherwise a repeat call is almost guaranteed.
Diagnostics are free: the technician finds the cause, explains which component failed, and approves the work before repair begins. The check starts with the power supply and lamp unit, then the control board and optical path are inspected — so the cause is found without disassembling the entire device. You see exactly what is being checked and why a particular component is named, instead of getting a dry "it's broken, we're replacing it." The cost is quoted after the check, when the cause is clear — so no unnecessary work "just in case" ends up in the estimate. If the scope of work doesn't suit you, you pay only for the part already done, not for the check itself. Approval happens before the technician picks up a tool, so the final result doesn't change along the way.
The time depends on the component: cleaning and lamp replacement are usually faster than work on the board or matrix replacement, and the exact timeframe is given after the check. The lamp and LED module are replaced as separate units, while the control board and matrix require meticulous soldering and alignment. The duration is also affected by how neglected the optical path is: a dust-clogged channel is cleaned first, and only then the condition of the matrix is assessed. Promising "within an hour" before inspection would be dishonest to the client — not only the work but also the replacement component itself determines the time. You get an accurate estimate on site, before the technician starts disassembly, and with it you decide whether to proceed or limit yourself to cleaning.
The main fear after repair is that the device will break again and the money will be wasted. Here's what the warranty covers and what to do if overheating comes back.
We provide a 1-year warranty on labor and parts, including lamp and LED module replacement — this covers both the technician's work and the installed part. In arrangements like this, both parts matter: replacing a projector lamp without covering the labor leaves the client alone with repeated disassembly of the case, while a warranty only on labor doesn't protect against a defective part. The LED module and lamp are consumable components with a limited lifespan, and their failure in the first months after installation is almost always due to the quality of the component, not operating conditions. Warranty on a part and on labor are different things, and it's important for the client that both are covered: otherwise a repeated failure of the part remains their problem.
If the projector overheats again after repair, we take it as a reason to revisit the cause: most often there's a clogged air duct or fan that was overlooked, not the replacement itself. The dust filter and cooling fan impeller collect lint and dust, and when the ducts are clogged, hot air can't escape the housing even with a working unit. In such cases, maintenance matters more than another replacement: we blow out the entire cooling chain, check the fan operation, inspect the radiator and air ducts against the light, and only then draw conclusions about the cause. We also check whether the fan speed has dropped and whether the thermal paste under the radiator has dried out — overheating after repair is often linked to these two points, not the replaced part. Repeated overheating almost always means the symptom was fixed, not the cause, so on return we check the entire cooling chain, not just the replaced unit.
We accept payment via Kaspi QR, Kaspi Red (instalments), bank card, cash, or bank transfer for companies, and the technician quotes the price after free diagnostics, once the cause and scope of work are clear. Diagnostics are free and take place before any disassembly or replacement, so the estimate is based on the actual condition of the optics and board, not on phone guesses. You can pay for the work in a way that suits you — cash or card — and the method doesn't affect the list of work or the warranty. The technician lists the cost of work and parts as separate lines so you can see what makes up the total and what exactly the warranty covers. A transparent estimate before work begins is part of the same peace of mind: you know in advance what you're paying for and won't face extra charges during the job.
Projector restoration depends on the device type and light source, so we show which devices we work with and give a criterion for when to repair and when replacement makes more sense.
| Projector type | Light source | What we check for a dim picture | What we replace most often |
|---|---|---|---|
| Lamp | Lamp | Lamp wear, optics | Lamp |
| LED | LED module | Module degradation, power supply | LED module |
| Laser | Laser source | Power supply and cooling | Unit based on diagnostics |
We service Epson, BenQ, Acer, and Xiaomi projectors, including those bought outside Kazakhstan — the country of purchase doesn't hinder diagnostics and restoration. Portable models and ceiling-mounted units of these brands come in with various faults: compact ones more often suffer from optics, lens, and connection ports, while ceiling-mounted ones have issues with the cooling system, fans, and ceiling mount. The technician inspects the housing, checks the power supply, fans, and optical path, and free diagnostics show which component has failed and what needs replacing. For gray-market projectors, it's important to specify the model in advance: it determines which board or module to check first, not where the device was bought. Portable and ceiling versions of the same brand differ in layout, so the technician asks not only the brand but also the exact model number. Our specialists have 4 to 20 years of experience, so based on symptom descriptions they often name the likely unit before even visiting.
Repair makes sense when a single component fails — a lamp, fan, or connector — while replacement is worth considering if the matrix has degraded and the work involves half the case. The lamp and fan are replaced as separate parts, the power connector is restored by soldering, but a burned-out matrix often comes as a unit with the optical block, and then the scope of work grows sharply. The practical criterion for technicians is to count not the projector's age but how many parts need replacing: one is fixed, several in a row — already a reason to compare with a new one. During free diagnostics, we identify exactly what has failed, and the technician provides the cost after inspection, and the client decides whether to repair the device or buy a new one. The age of the device itself is not a verdict: even a projector with a solid history with one breakdown remains more cost-effective than replacement, while with two or three units to replace, the bill is no longer in favor of repair.
Projector symptoms add up to a clear picture: some point to power and cooling, others to optics and the matrix. Below is a short summary to help you choose the order of actions.
18brands
We work with Epson, BenQ, Acer, ViewSonic, Sony, LG, Optoma, and Vivitek projectors — we source compatible parts for each model line.
Tech Service technicians repair other appliances too — with the same 1-year warranty on labour and parts.
Refrigerator Repair in Almatyfrom 3 000 ₸
Washing Machine Repair in Almatyfrom 3 000 ₸
Dishwasher Repair in Almatyfrom 3 500 ₸
Oven Repair in Almatyfrom 3 000 ₸
Cooktop Repair in Almatyfrom 3 500 ₸
Air Conditioner Repair in Almatyfrom 3 500 ₸
Boiler and Water Heater Repair in Almatyfrom 2 500 ₸
Freezer Repair in Almatyfrom 6 000 ₸
Tumble Dryer Repair in Almatyfrom 5 000 ₸
Coffee Machine Repair in Almatyfrom 2 500 ₸
Robot Vacuum Cleaner Repair in Almatyfrom 3 500 ₸
Vacuum Cleaner Repair in Almatyfrom 1 500 ₸
Microwave Oven Repair in Almatyfrom 2 000 ₸
Hair Dryer Repair in Almatyfrom 1 500 ₸
Iron Repair in Almatyfrom 3 000 ₸
Electric Kettle Repair in Almatyfrom 2 500 ₸
Mixer Repair in Almatyfrom 2 500 ₸
Multicooker Repair in Almatyfrom 500 ₸
If your laptop screen is broken, turn the device off first, don't press on the display, and check the picture through an external monitor.
12 March 2026 · 11 minutes read
If your laptop freezes, the first thing to do is restart it and check Task Manager to see what's loading the CPU and memory.
25 January 2026 · 12 minutes read
If your computer won't turn on, start simple: check the outlet, power cable, switch on the power supply, and the power button.
19 January 2026 · 13 minutes read
If your laptop won't boot, first determine which of two states you're in: the device doesn't respond to the power button at all…
13 December 2025 · 12 minutes read












