Open until 19:00+7 (778) 096 59 61Call a technician
Tech Service technician next to a electric moped

Electric Moped Repair in Astana

A technician arrives within 60 minutes anywhere in the city. Free diagnostics, 1-year warranty on labor and parts.

  • 1-year warranty
  • Free diagnostics
  • 4 to 20 years of experience

Our own technicians4 to 20 years of experience

Kairat A.Ruslan S.Nikita O.Kuanysh A.

Repair prices

  • Diagnostics0 ₸
  • Charger repairfrom3 500 ₸
  • Firmware update and calibrationfrom3 500 ₸
  • Battery replacementfrom4 000 ₸
  • Hydraulic brake bleedingfrom4 000 ₸
All prices
ours5,06 127 reviews
order database
Common faultsCommon faultsTECH SERVICE02

Common electric moped faults in Astana

Below are typical symptoms owners report and their likely causes. The technician confirms the exact cause after a free diagnostic.

PricesPricesTECH SERVICE03

How much electric moped repair costs in Astana

The table lists the 'from' price for labor, for common jobs also the 'from' price of the part, plus the time required to complete the job.

Charger repairparts not included

1–3 hours

from3 500 ₸

Firmware update and calibrationexact price — after the free diagnostics

1–2 hours

from3 500 ₸

Battery replacementparts not included

1–2 hours

from4 000 ₸

Hydraulic brake bleedingexact price — after the free diagnostics

1–3 hours

from4 000 ₸

Brake shoe replacementparts not included

1–3 hours

from4 500 ₸

Before and afterBefore and afterTECH SERVICE04

Before and after electric moped repair in Astana

Headlight wiring break

1 daytime

from 6,000 ₸cost

Problem
Due to constant shaking on uneven surfaces, the wire harness to the headlight chafed through and broke; the light went out.
What we did
The technician tested the circuit, restored the connection, and insulated the splice in corrugated tubing.
Result
The headlight works; the wiring is routed in corrugated tubing and protected from chafing.
I want the same
A black electric scooter stands on the workshop floor, no people.BeforeAfter
01 / 03
All repairs
TECH SERVICE mobile technician with a tool case

How electric moped repair works on site in Astana

From request to final check — a clear step-by-step process.

  1. Choose the formatbefore the visit

    Decide where you'd like the repair done: at your location or at the workshop if a stationary stand is needed.

  2. Technician visitwithin 60 minutes

    The technician comes to you anywhere in the city and inspects the scooter on site.

  3. Work approvalbefore repair

    The technician lists the replacements, and the owner confirms the scope of work before disassembly.

  4. Location and timeat booking

    Agree on where to meet the technician, whether a power outlet is needed to check charging, and who will be present during the inspection.

  5. Checklist acceptanceafter repair

    Compare the replaced parts with the work list and confirm the warranty terms for labor and parts.

Leave a request

We reply during working hours

Book electric moped repair in Astana

Describe the issue and your scooter model — the technician will arrange a time and place with you. Ask about payment and parts availability.

TECH SERVICE administrator replying to a customer's WhatsApp message

Warranty question? Call us

+7 (778) 096 59 61
Customer reviewsReviewsTECH SERVICE05

Reviews of electric moped repair in Astana

5,0ours

6 127 reviews of repairs at TECH SERVICE in total

Михаил У.Order No. ZK-2025-495 · 2 May 2025

ours

Позвонил, потому что техника встала и ждать было некогда. Знакомый мастер раньше здесь работал, дал номер. Про тех сервис слышал на Сарыарке. Выдали всё официально, для бухгалтерии подошло. Не пришлось ездить дважды. Пользуюсь и вспоминаю добрым словом

Еркежан К.Order No. TSA-75572 · 14 November 2024

ours

Приехал по записи, всё было готово к моему приходу. Работу закончили раньше срока. Для Астаны — хороший вариант.

Яна Э.Order No. 40702 · 10 March 2022

ours

Позвонили из сервиса сами, напомнили о записи. Рустем Т — мастер от бога, если можно так сказать. Объяснили, как продлить срок службы. Работу закончили раньше срока. Выдали квитанцию и гарантийный талон. Общение спокойное, без навязывания. Назвали сумму заранее, в конце она не поменялась. Мастер посмотрел при мне, объяснил, что случилось. Выдали всё официально, для бухгалтерии подошло. Для Астаны — хороший вариант

Ырысгуль Н.Order No. TSA-46076 · 10 November 2020

ours

Искал сервис, где дают гарантию и чек. Не идеально, но по-честному). Достарыма айтамын.

Константин О.Order No. 2005-3515 · 3 February 2020

ours

Первый раз обратился, до этого чинился у знакомого. Мастер опоздал, правда предупредил. Не пришлось ездить дважды. Общение спокойное, без навязывания. Сделали то, что обещали, и ничего лишнего. Выдали всё официально, для бухгалтерии подошло. Сказали, что запчасть есть на складе. Обращусь снова, если понадобится.

Ангелина Я.Order No. 1908-7645 · 20 June 2019

ours

Позвонил, потому что техника встала и ждать было некогда. В целом доволен.

Темирлан Ц.Order No. TSA-31269 · 6 February 2019

ours

Зашёл узнать цену, в итоге оставил технику. Турарбек Кайрош пообещал и сделал, без напоминаний. Выдали квитанцию и гарантийный талон. Не пришлось ездить дважды. Для Астаны — хороший вариант)

Григорий И.Order No. AST-1802-310 · 17 November 2018

ours

Зашёл узнать цену, в итоге оставил технику. Цену не подняли, хотя работа оказалась сложнее. Оформили быстро, без анкет и лишних вопросов. Сервис оставил нормальное впечатление!!

Геннадий Ж.Order No. TSA-54830 · 29 January 2018

ours

Долго выбирал, остановился на этом варианте. Всё проверили при выдаче. Не идеально, но по-честному.

Ангелина Я.Order No. ZK-2017-738 · 24 February 2017

ours

Первый раз обратился, до этого чинился у знакомого. Всё проверили при выдаче. Выдали квитанцию и гарантийный талон. Держали в курсе по телефону. Сказали, что запчасть есть на складе. Сделали то, что обещали, и ничего лишнего. Объяснили, как продлить срок службы. Работу закончили раньше срока. Приняли технику в конце дня, не отправили домой. В целом доволен.

See all reviews

Our technicians in Astana

01 / 08
Kairat A., senior small appliance technicianexperience14 years

Kairat A.

Senior small appliance technician

Ruslan S., on-site coffee machine diagnostics technicianexperience15 years

Ruslan S.

On-site coffee machine diagnostics technician

Nikita O., coffee machine cleaning technicianexperience5 years

Nikita O.

Coffee machine cleaning technician

Kuanysh A., coffee machine diagnostics technicianexperience12 years

Kuanysh A.

Coffee machine diagnostics technician

Aydar A., portafilter coffee machine technicianexperience5 years

Aydar A.

Portafilter coffee machine technician

Serikbay A., vacuum cleaner repair technicianexperience12 years

Serikbay A.

Vacuum cleaner repair technician

Artur G., vacuum cleaner repair technicianexperience15 years

Artur G.

Vacuum cleaner repair technician

Akzhol K., washing machine repair technicianexperience18 years

Akzhol K.

Washing machine repair technician

Questions and answersQuestionsTECH SERVICE06

Questions about electric moped repair in Astana

Didn’t find the answer? Message us on WhatsApp.

Ask a question
Why does my electric scooter jerk when I press the throttle?

Most often it's the throttle grip, the Hall sensor in the hub motor, or a loose connector in the wiring. A technician will check the signals during free diagnostics and pinpoint the exact cause.

What should I do if my electric scooter won't turn on after getting wet?

Don't try to turn it on again or charge it: moisture inside can cause a short circuit. Dry the body and take it to a service center — a technician will check the wiring, controller, and battery after diagnostics.

Why does my electric scooter go less distance on a single charge?

Usually the cause is battery wear or imbalance, less often a faulty controller or BMS. Free diagnostics will give you a precise answer by checking the capacity and condition of the battery cells.

Do you repair Kugoo and Ninebot electric scooters in Astana?

Yes, these brands are among those we work with, along with Xiaomi and other popular brands. The technician will confirm whether a specific component can be repaired after inspection, as it depends on the model.

Why is riding an overheated electric scooter dangerous?

Overheating of the hub motor or controller can melt insulation and cause a short circuit, and in the worst case, a battery fire. If the body is hot, stop riding and take it to a service center to check the cooling system and electronics.

Can I replace only the broken component on an electric scooter instead of the whole unit?

It depends on the model and the component: brake pads, tires, or throttle grips are replaced separately, while the controller and BMS are sometimes repaired at the component level. After diagnostics, the technician will tell you whether replacement or repair is more cost-effective.

Repair guideArticleTECH SERVICE07

Electric scooter repair in Astana by Tech Service with on-site technician

Kairat A., senior small appliance technician

Author: Kairat A.,Senior small appliance technician

Published
Updated

Tech Service repairs electric scooters in Astana as a direct provider: our technician arrives at your home within 60 minutes anywhere in the city or takes the scooter to our service center. Diagnostics are free, the technician gives you the price after diagnostics, you get a 1-year warranty on labor and parts, and our technicians have 4 to 20 years of experience.

Why an electric scooter won't turn on, won't charge, or jerks

A symptom is just the starting point. The technician looks for the component responsible for it: the same complaint can come from different faults. Below we break down which components cause each complaint and how they are told apart during diagnostics.

Won't turn on — battery, controller, or wiring

We start by measuring the voltage on the battery and checking the power circuit, because "won't turn on" sounds the same with a discharged battery, a triggered BMS protection, or a disconnected connector. The BMS board cuts the output when it detects overdischarge, overheating, or cell imbalance, and from the outside it looks like the scooter is completely dead. The controller may have gone into protection or burned out from a current surge, and the wiring and connectors may have oxidized and come loose after a fall. We do diagnostics for free, so we test the entire power circuit and power contacts instead of checking a single guess. If the scooter comes back to life after charging and reconnecting the connector, there's no need to replace an expensive component — that's why we always test before agreeing on any work.

Jerks and rides in surges — how we find the cause

Jerking while riding is most often related to the Hall sensors in the hub motor or to the controller supplying current unevenly, and the technician distinguishes these two causes by how the scooter behaves at different speeds. Hall sensors tell the controller the rotor position, and when one of the three channels fails, the wheel starts to jerk at startup and at low speed. A controller with a damaged power stage causes dips under load and on inclines, where current is highest. We also check the phase wire connector and the throttle — an oxidized contact gives the same symptom. Jerking at low speed with smooth running at high speed points to the sensors, while dips under load point to the controller; this determines whether the component can be repaired or needs replacement.

Won't charge and drains quickly

If the electric scooter doesn't charge fully or loses charge faster than usual, we check the charger, charging port, BMS board, and the condition of the battery cells — the problem can be in any of these links. The charger may no longer output the required voltage, the port may be melted and loose from frequent plugging, the BMS may not balance the cells and cuts charging early. Each cell in the pack ages differently, and the weakest one drags down the whole battery. The BMS board monitors cell charge and discharge, so we compare its readings with the actual voltage at the terminals. Fast charge loss with normal charging usually indicates cell wear rather than a charger issue, so replacing the charger blindly makes no sense.

Overheats while riding or charging and brakes poorly

Overheating around the hub motor signals controller problems or excessive load, while weak braking indicates worn brake pads and requires a separate check of the brake system. A controller with blown power switches heats up itself and heats the windings, and riding uphill with an overload overheats the motor even with healthy electronics. Brake pads wear unevenly, the cable stretches, the brake lever travel increases, and braking efficiency drops. Heating during charging and heating during riding are different scenarios: the first points to the charging circuit, the second to the power stage, and they must not be confused. During diagnostics, the technician first notes when the heating occurs, and only then removes the suspected component.

What an error code on the display means and how to read it

The code on the display is a hint, not a verdict: it narrows down the components, but diagnostics confirm the exact cause. Let's look at how to read the signal and what to do before the specialist arrives.

The code points to a component, not a specific fault

The code on the display points to a specific component that the technician checks, but it doesn't name the faulty part — the same code can mean a break in the circuit, a sensor failure, or controller protection. An E-series symbol usually involves a chain from the controller, Hall sensors in the hub motor, and the battery's BMS board: the signal passes through all three, and a failure in any link produces a similar picture. The same number can mean different things on different models — some manufacturers tie it to voltage, others to motor RPM. So decoding without measuring at the component itself leads to replacing working parts; we always confirm the signal with diagnostics.

How a technician works with the code on-site

On-site, the technician reads the code, compares it with how the scooter behaves, and checks the component right there. If the work can only be done at the service center, the scooter goes there. First, they match the code with how the e-scooter performs under load: stalls on a hill, jerks when starting, or won't take a charge. Then they test the circuit from the battery connector to the controller, check the Hall sensors, and look at the BMS readings. Diagnostics are free, and a specialist arrives at your home within 60 minutes anywhere in the city — direct service, no middlemen. Note the symbol and the conditions when it appears — during acceleration, going uphill, or while charging; that speeds up the check more than the number itself.

What to do before the technician arrives

  • Don't open the casing: opening the panel or hub motor before diagnostics throws off settings and prevents the specialist from seeing the original fault pattern.
  • Save the code on the display: take a photo and note when it appears — at start, during acceleration, or when you plug in the charger.
  • Stop riding if you notice warning signs: a burning smell, a hot casing, or no response to the throttle means don't start the scooter and wait for a specialist.
  • Don't reset the error with a button: clearing it erases the clue that helps narrow down the components, and the check will have to start over.
  • Have the charger ready: it helps determine whether the signal is related to power supply or the battery itself.

How repairs work at home and at the service center

The format depends on the component: some operations are done on-site, others require the service center. Below is what free diagnostics includes, the list of on-site work, and how to prepare for the specialist's visit.

What free diagnostics includes

  • Power circuit: testing connectors, fuses, and wiring for breaks or burnt contacts.
  • Battery and BMS board: measuring cell voltage and checking how the board balances the charge.
  • Controller: testing output keys and response to the throttle — a common source of jerking and power drops.
  • Hub motor: Hall sensors, bearing play, and winding resistance.
  • Controls: throttle, brake levers, power button, and display.
  • Brake system: pad wear, disc condition, and cable operation.
  • Fasteners and frame: cracks along welds, bolted joints, and kickstand condition.

Work at home and at the service center

WorkWhere it's doneWhat we check
Component diagnosticsAt homePower circuit, battery, controller
Tube and tire replacementAt homeTires, tubes, rims
Brake padsAt homeBrake system
Battery and BMS repairAt the service centerBattery cells, BMS board
Controller and hub motorAt the service centerHall sensors, output keys

How to request a technician and what to prepare

A technician arrives at your door within 60 minutes anywhere in the city, so before they arrive, just clear some space, charge the scooter as much as possible, and describe the symptoms. Diagnostics are free, and the cost of work is quoted after them, once the cause is clear. The on-site technician brings tools for typical operations on the spot, and if the breakdown requires disassembling power components, they'll tell you right away — and the work is moved to the workshop. Clear a path to the scooter and lift it so the rear wheel can spin: rotation under load is checked with the wheel off the ground. Think in advance about the conditions when the fault appears — during acceleration, after rain, in cold — this detail helps identify the component even before the visit.

Cost and warranty for repairs

Cost and warranty are the two questions that decide whether to repair or replace. Below we break down what goes into the price, what coverage the warranty provides, and when repair makes more sense than buying new.

What goes into the cost

The technician quotes the cost after free diagnostics, and it consists of labor and parts for the specific component — battery, controller, hub motor, or brakes. We perform diagnostics for free: first we find the cause, then we agree on the amount, and only after agreement does the work begin. Replacing the battery, resoldering the BMS, replacing the controller, and fixing the hub motor are jobs of different complexity with different sets of parts, so they add up differently. The same symptom on two models can cost differently due to different components, so it's impossible to quote a price based on a description of the breakdown — an inspection and on-site check of components are needed first. In my experience, people most often confuse the price of a part with the price of labor: the owner sees a cheap aftermarket part online and expects the same total, but in fact they also pay for installation, setup, and checking related components.

1-year warranty coverage

We provide a 1-year warranty on labor and parts, and this is especially important when servicing expensive components — the battery, controller, and hub motor. Coverage applies to both components at once: the installed part and how the technician installed and connected it. When servicing an electric scooter, both parts matter because a component failure can be caused by either the part or the installation — for example, a new controller fails due to a wiring connection error. Therefore, we handle warranty cases based on the facts: we check what exactly failed and fix the cause, not just the symptom. Warranty on a part and on labor are different things, and in our practice both parts are covered by a single term, which simplifies handling any claim. The owner should keep records of the replaced component — they make it easier to match a failure to specific work.

Repair or buy new

Repair makes sense when one component is faulty and the rest are working; if the battery, hub motor, and controller are all worn out, replacing the equipment may be more reasonable. Age alone is a poor guide: a well-maintained electric scooter with a single failure is often cheaper to repair than to replace, and new equipment's components don't last forever either. Free diagnostics before service show the real picture: how many components need attention and which are still in working order. The decision is made after diagnostics, not based on the age of the equipment — the technician lists the components that can be restored and those that are already worn out, and then the owner decides. Moreover, you should consider not only the labor but also the remaining life of working components: if the battery and hub motor are fine, investing in one component pays off over a longer period than it seems from the first estimate.

Specific types of work on electric scooter components

Some breakdowns are not a general failure but a separate job on a specific component. Below we cover work on the battery, controller, hub motor, and wheel.

Battery replacement and BMS repair

The battery is replaced when the cells are worn out and the range no longer recovers. If the problem is in the BMS board, it is checked first because it controls charging and discharging. During free diagnostics, we open the case, test the cells under load, and compare the board readings with reference values—a voltage drop reveals wear in one section while the others are still good. The BMS board shuts off the battery on overheating and balances the cells, so its failure can masquerade as a "dead" battery: the scooter won't charge or stalls on a hill. Repairing the board costs less than a full battery replacement, and in our practice such cases are not rare—the Tech Service technician first rules out the board itself and only then suggests replacing the cells. A quick battery swap without checking the BMS brings the scooter back to the service center: a faulty board will again ruin the new cells.

Controller and hub motor

The controller manages the current to the hub motor, so it is checked when there is jerking or overheating, and in the hub motor the Hall sensors that ensure smooth operation are inspected separately. On-site, the technician opens the controller compartment, checks the power switches and phase wire contacts—a burnt connector gives the same symptoms as a burnt board. The Hall sensors are inside the wheel and report the rotor position to the control unit; if they fail, the scooter jerks or won't start. Diagnostics test these components one by one so as not to replace working electronics because of a single sensor. An overheated wheel doesn't always mean it needs replacement—sometimes the control unit is to blame for sending incorrect current. The technician performs such electric scooter repair in Astana on-site, and takes complex cases to the service center.

Tire puncture and brake pads

WorkComponentWhat we check
Puncture repairWheelInner tube, tire
Tire replacementWheelTread wear
Pad replacementBrake systemPad thickness, disc
Brake adjustmentBrake systemLever travel, effectiveness

Brands and maintenance

Brand compatibility and proper care reduce the frequency of service visits. Below are the electric scooters we work with and the habits that extend battery life.

Brands we work with

We service Xiaomi, Kugoo, and Ninebot electric scooters, as well as other models, and free diagnostics show whether a component can be restored or needs replacement. Xiaomi is the most common—the M365 line and its successors have a weak point in the controller and connector moisture protection; Kugoo and the Kugoo S series have a stressed hub motor and deck mount; Ninebot Max comes in with tire and brake pad wear. On-site, the technician opens the case, checks connectors, cables, and the battery pack, compares readings with the display code, and only then quotes the scope of work. Different brands with the same symptom point to different components due to different control schemes, so mention the model and firmware version when booking—the technician will arrive with the right parts.

How to extend battery life

  • Charge to full: plug in the scooter after every ride, don't leave the battery discharged for long—deep discharge accelerates cell wear.
  • Storage temperature: keep the scooter warm; in winter, don't leave it on a balcony or in an unheated garage.
  • Partial charge during inactivity: for long storage, keep the scooter at about half charge and top it up every few weeks.
  • Avoid sudden loads: avoid long climbs at full power and starting uphill from a standstill—peak currents heat the battery and controller.
  • Keep it dry and clean: wipe the body and connectors after riding on wet asphalt; moisture speeds up contact corrosion.

When it's time for diagnostics

You should come in for diagnostics if you notice a drop in range, jerking, overheating, or a new code on the display — an early check costs less than repairing a failed component. A range that has dropped noticeably from what you're used to usually points to cell wear or an unbalanced pack, while jerking and overheating suggest the controller or wiring. Our free diagnostics include checking the battery pack, connectors, brake pads, and a test run; the technician then names the likely cause and scope of work. A preventive check catches cell and pad wear before symptoms appear, so it's done on schedule, not just after a breakdown. For residents of the capital, it's worth checking the scooter before the season starts — weak spots show up first after a winter of disuse.

Getting electric mopeds back on the road

Electric scooter repair comes down to three steps: notice the symptom, narrow down the components, and confirm the cause during diagnostics. Below is a quick summary to help you decide before contacting a technician.

  • A symptom is not a diagnosis: a fault points to a component, but the exact cause is confirmed by disassembly and part inspection.
  • An error code narrows the search: it rules out systems that are definitely working, but it doesn't name the specific faulty part.
  • The format depends on the component: some work is done on-site, while complex cases are taken to the service center.
  • Cost comes after the check: the price is quoted based on the free diagnostics, and the warranty covers labor and parts.
  • Prevention pays off: proper charging and scheduled checks extend battery life and reduce the risk of sudden failure.

8brands

Which electric moped brands we repair in Astana

Our technicians service the most common electric scooter models you see around the city.

We also repairWe also repairTECH SERVICE08

Besides electric moped repair, we fix other equipment in Astana

Tech Service technicians repair other appliances too — with the same 1-year warranty on labour and parts.

BlogBlogTECH SERVICE09

Worth reading before electric moped repair in Astana

Leave a review

Choose a platform — the TECH SERVICE page will open.

Send a review with photos on WhatsApp