Open until 19:00+7 (778) 046 88 53Call a technician
Tech Service technician next to a asic miner

ASIC Miner Repair in Astana

A technician arrives within 60 minutes anywhere in the city. Free diagnostics, 1-year warranty on labor and parts.

  • 1-year warranty
  • 4 to 20 years of experience
  • You can pay via Kaspi QR, Kaspi Red, bank card, cash, or bank transfer for companies

Our own technicians4 to 20 years of experience

Nikita M.Daulet T.Azim K.Zhangeldy M.

Repair prices

  • Diagnostics0 ₸
  • Fan replacementfrom4 000 ₸
  • Cable and connector replacementfrom5 500 ₸
  • Firmware updatefrom6 000 ₸
  • Setup and optimizationfrom6 000 ₸
All prices
ours5,06 127 reviews
order database
Common faultsCommon faultsTECH SERVICE02

Common ASIC miner faults in Astana

Below are frequent symptoms and their likely causes. The technician will pinpoint the exact cause after diagnostics.

PricesPricesTECH SERVICE03

How much ASIC miner repair costs in Astana

The table lists the 'from' price for labor, for common jobs also the 'from' price of the part, plus the time required to complete the job.

Fan replacementparts not included

1–2 hours

from4 000 ₸

Cable and connector replacementparts not included

1–2 hours

from5 500 ₸

Firmware updateexact price — after the free diagnostics

1–2 hours

from6 000 ₸

Setup and optimizationexact price — after the free diagnostics

1–2 hours

from6 000 ₸

Hash board chip replacementparts not included

1–2 days

from7 500 ₸

Before and afterBefore and afterTECH SERVICE04

Before and after ASIC miner repair in Astana

Power connector on the board has no contact

1–2 hourstime

from 5,500 ₸cost

Problem
Due to constant reconnections, the power connector on the hash board became loose and burned, and the miner would not start.
What we did
The technician resoldered the contacts and restored a reliable connection.
Result
The miner starts and runs stably; the connection has been tested under load.
I want the same
An aluminum mining machine with a fan stands on a workbench in a workshop, next to it a screwdriver on a napkin.BeforeAfter
01 / 03
All repairs
TECH SERVICE mobile technician with a tool case

How ASIC miner repair works at your site in Astana

Five steps from your request to equipment check.

  1. Requeston the day of request

    Submit a request by phone or messenger, describe the symptom and model.

  2. Symptom recordingbefore disassembly

    The technician clarifies operating conditions and failure history before disassembly.

  3. Parts selectionafter inspection

    The technician selects parts compatible with your specific model and agrees on their cost.

  4. Repairby appointment

    After cost approval, the technician performs the work and replaces parts.

  5. Warranty confirmationat pickup

    You receive a document confirming a 1-year warranty on labor and parts.

Leave a request

We reply during working hours

Book ASIC miner repair in Astana

Have the serial number, model, and device location ready. This helps the technician prepare tools and parts for your call.

TECH SERVICE administrator replying to a customer's WhatsApp message

Warranty question? Call us

+7 (778) 046 88 53
Customer reviewsReviewsTECH SERVICE05

Reviews of ASIC miner repair in Astana

5,0ours

6 127 reviews of repairs at TECH SERVICE in total

Инна Н.Order No. 39750 · 8 June 2026

ours

Нужен был срочный ремонт, позвонил утром. Выдали всё официально, для бухгалтерии подошло. Не пришлось ездить дважды. Тихо, ровно, без сюрпризов

Ангелина Я.Order No. AST-2612-235 · 12 May 2026

ours

Искал сервис, где дают гарантию и чек. Сосед по площадке хвалил, решил проверить. Дамир М разрулил всё быстро. Позвонили, когда можно забирать. Оформили быстро, без анкет и лишних вопросов. Выдали квитанцию и гарантийный талон. Сервис оставил нормальное впечатление!!

Любовь Ю.Order No. ZK-2025-363 · 26 September 2025

ours

Первый раз обратился, до этого чинился у знакомого. Дамир М сам позванил и сказал, что готово

Константин О.Order No. 2411-6808 · 28 October 2024

ours

Первый раз обратился, до этого чинился у знакомого. С левого берега ехать далеко, поэтому искал поближе к дому. Объяснили, как продлить срок службы. Цену не подняли, хотя работа оказалась сложнее. Тихо, ровно, без сюрпризов

Семён Ш.Order No. ZK-2023-286 · 26 May 2023

ours

Приехал по записи, всё было готово к моему приходу. Астанинский Tech-service — нормальный вариант.

Мария Р.Order No. AS-9664 · 24 October 2022

ours

Пришёл по совету коллеги, у него тут чинили ноут. Для Астаны — хороший вариант.

Лариса О.Order No. TSA-37287 · 6 November 2020

ours

Первый раз обратился, до этого чинился у знакомого. Оформили быстро, без анкет и лишних вопросов. В целом доволен.

Людмила Щ.Order No. ZK-2020-654 · 14 May 2020

ours

Нужен был срочный ремонт, позванил утром. Дамир М объяснял без умных слов, за это спасибо)

Людмила Щ.Order No. AST-1808-565 · 21 August 2018

ours

Пришёл по совету коллеги, у него тут чинили ноут. Переезжали в новую квартиру, техника после перевозки захандрила. Назвали сумму заранее, в конце она не поменялась. Работу закончили раньше срока. Мастер посмотрел при мне, объяснил, что случилось. Приняли технику в конце дня, не отправили домой. Выдали всё официально, для бухгалтерии подошло. Объяснили, как продлить срок службы. Позвонили, когда можно забирать. В целом доволен.

Иван Н.Order No. TSA-57787 · 13 February 2017

ours

Зашёл узнать цену, в итоге оставил технику. Общение спокойное, без навязывания. Держали в курсе по телефону. Впечатление положительное!!

See all reviews

Our technicians in Astana

01 / 07
Nikita M., PC and network repair engineerexperience7 years

Nikita M.

PC and network repair engineer

Daulet T., senior mobile computer technicianexperience11 years

Daulet T.

Senior mobile computer technician

Azim K., laptop repair technicianexperience10 years

Azim K.

Laptop repair technician

Zhangeldy M., motherboard repair technicianexperience9 years

Zhangeldy M.

Motherboard repair technician

Tursynbay A., printer repair technicianexperience16 years

Tursynbay A.

Printer repair technician

Nurkhan I., computer repair technicianexperience12 years

Nurkhan I.

Computer repair technician

Azamat Kh., all-in-one computer repair technicianexperience18 years

Azamat Kh.

All-in-one computer repair technician

Questions and answersQuestionsTECH SERVICE06

Questions about ASIC miner repair in Astana

Didn’t find the answer? Message us on WhatsApp.

Ask a question
Can a miner's hash board be repaired, or is it replaced entirely?

It depends on the type of damage: local defects like burned chips, power circuits, or connectors are usually repairable. Replacement is needed when the board is irreversibly damaged or repair isn't cost-effective. The technician explains the decision after free diagnostics.

Why has the miner's hashrate dropped by half?

Most often this points to a hardware issue: chip degradation, power failure, or one of the hash boards dropping out. Sometimes the cause is firmware or settings, depending on the model. Diagnostics gives the exact answer, not guesswork.

Do you repair miners from manufacturers other than Bitmain?

Yes, we take miners from various brands, not just Antminer by Bitmain. The list of components and typical jobs depends on the device model. You can check for a specific brand when you submit a request.

What's the risk of continuing to mine on a miner with a faulty hash board?

A damaged board and power circuits can drag down neighboring components and the power supply, and overheating speeds up chip degradation. In the end, repairs cost more than early intervention. It's better to stop the device and show it to a technician.

What can I check myself if the miner doesn't detect a hash board?

It's worth inspecting the cables and connectors for oxidation and poor contact, checking the power, and rebooting the device. If the board still isn't detected, it's a hardware issue and needs repair. Disassembling it yourself without experience is risky.

Can I have just the fan repaired on a miner without handing in the whole unit?

Yes, replacing the fan and bearings is a separate job, and other components aren't touched. This repair eliminates noise and restores cooling. We check the rest as needed after diagnostics.

Repair guideArticleTECH SERVICE07

ASIC miner repair in Astana by Tech Service with on-site technician

Nikita M., PC and network repair engineer

Author: Nikita M.,PC and network repair engineer

Published
Updated

Tech Service repairs ASIC miners in Astana: a technician arrives at your home within 60 minutes, or you can bring the miner to our service center. Diagnostics are free, we quote the price after diagnostics, and we provide a 1-year warranty on labor and parts. We fix hash boards, power supplies, and cooling systems on miners from various manufacturers.

Why an ASIC miner won't turn on, overheats, or loses hashrate

Most requests start with one of several symptoms: the device won't start, goes into thermal protection, or loses hashrate. Let's break down what each sign usually means and where the check begins.

ASIC miner won't turn on and shows no signs of life

Most often, the device won't turn on due to a power supply or a power circuit on the control board, and during free diagnostics we check this chain first. The power supply delivers power to the miner's boards through connectors and cables, and a break or voltage drop anywhere in this chain leaves the miner without startup. The control board may still be intact — the technician tests the connectors, checks the cables for oxidation and breaks, and evaluates the output voltages of the power supply under load. This check takes little time and doesn't require disassembling the hash boards. If the indicator on the power supply doesn't light up when connected, don't disassemble the device yourself — with a faulty power supply, repeated power-ons can damage neighboring components.

Miner overheats and shuts down due to temperature

Overheating and temperature shutdown are usually caused by clogged heatsinks, worn-out fans, or dried-out thermal interface, and we check the entire cooling system. Fans remove heat from the heatsinks, and thermal paste or thermal pads work between the chips and the heatsink base — over time they lose their properties, and heat stops dissipating. The technician inspects the fan blades for chips, checks bearing rotation, blows dust out of the heatsink fins, and assesses the quality of the contact. Overheating is also affected by operating in a poorly ventilated room, but we look for the cause in the device itself. If after maintenance the miner goes into thermal protection again, it's a reason to review not only the fans but also the quality of the heatsink contact with the chips.

Error code, hashrate loss, and invisible hash board

  • Hash board error code: indicates a fault in the chips or circuit on a specific board, not pool settings.
  • Hashrate drops by half: usually means one of the hash boards has stopped producing results or is working unstable.
  • Board not visible in the interface: most often the problem is in the connector or cable, less often in the board itself.
  • Errors on different boards one after another: a reason to check the power supply and overall cooling, not to replace boards one by one.
  • Unstable hashrate without an error code: a sign of overheating of individual ASIC chips or poor cable contact.
  • Check before replacement: before agreeing to a new board, the technician rules out overheating and cable contact — this can be solved on the spot.

How free miner diagnostics work

Diagnostics are the entry point for any work: we'll show what it includes, why it costs the owner nothing, and how the decision to restore is made based on its results.

What free diagnostics includes

  • Power supply: we check output voltages under load to rule out voltage drops and imbalances across the lines.
  • Hash boards: we test each one separately — looking for non-working ASIC chips and breaks in the circuit.
  • Cooling system: we inspect fans, heatsinks, and thermal paste for overheating and clogging.
  • Controller: we check the control board, firmware, and communication with the computing boards.
  • Cost after diagnostics: the technician states the scope of work and the price, and restoration begins only after your approval.
  • Explaining the result: ask to show which component failed the check — this explains why the work costs what it does and what actually needs replacing.

Hash board repair or full replacement

We first try to repair the hash board — replace faulty chips and restore the circuit, and only discuss replacement if it can't be fixed. The board carries a chain of ASIC chips connected in series: failure of one element breaks the entire circuit, and the unit stops producing results. The technician locates the damaged chip by the voltage drop in that section and replaces it by soldering, and if the traces are broken, restores the conductors. This approach preserves the other working elements and costs less than a new board. Deciding to replace makes sense when the cost of a new board is comparable to the price of a miner on the secondary market — otherwise the work loses its meaning, and we say so directly rather than silently swapping the unit.

When repair isn't cost-effective and what to do with the miner

We're honest when the work isn't cost-effective — if several computing boards and the power supply are faulty at the same time, the costs may exceed the residual value of the miner. When output drops on one unit, restoration is usually justified, but a combination of two or three dead boards with a blown power supply eats up all the benefit. In that case, the technician explains the breakdown by unit and suggests weighing the alternatives. Before writing it off, it's worth checking whether selling the device for parts is easier — working fans, heatsinks, and the case are often in demand among those building mining rigs. That way you recover part of the money instead of leaving a non-working device gathering dust. In our experience, this approach is often more beneficial to the owner than work for the sake of work.

Repair at home or at the service center

A miner is a heavy and noisy device, so the service format matters. Let's look at when it's more convenient to call a technician and when to bring the device to the workshop.

Technician visit within 60 minutes

The technician arrives at your home within 60 minutes anywhere in the city to perform diagnostics and, if possible, fix the issue on the spot. During the visit, we check the power, cooling, and contacts of the hash boards, clean the device from dust, and replace failed fans — these tasks don't require disassembling the case down to the base. Diagnostics are free, so based on the results, the technician will honestly say whether the problem can be solved at home or the device needs to be taken to the service center. Owners who have their miner in a noisy mining rig or on the balcony often choose the visit: no need to disconnect the rack, find transport, and risk the boards during transit. If the issue is in the power supply or cooling system, it's often resolved right on the spot — this saves a day on transportation back and forth.

Service center maintenance and when it's more convenient

It's more convenient to work in the workshop if you need to replace several units or the task requires disassembly and in-depth inspection rather than a visit. Complex soldering, restoring hash board traces, chip replacement, and thorough cleaning with full case disassembly are done in the workshop, where there's space and tools for the specific task. We accept miners at the client's home and at the service center — the owner chooses the format, not the technician imposing it. Moreover, if the device is already off the mining rig and not working, bringing it to the workshop is often faster than waiting for a visit, especially with a non-obvious fault that requires step-by-step checking. Before transporting, take a photo of the cable connections and carefully remove the miner from its mounts: this makes it easier for the technician to restore the setup and helps you avoid damaging the connectors in transit.

Comparison of repair formats

FormatSelection conditionsOn-site workWarranty
Home visitMiner is running, no time for transportDiagnostics, cleaning, fan replacement, power check1-year warranty on labor and parts
Repair at service centerNeeds disassembly, hash board replacement, complex solderingFull diagnostics and unit repair1-year warranty on labor and parts
Mixed optionNon-obvious faultDiagnostics on-site, repair in workshop1-year warranty on labor and parts

Warranty and responsibility for results

A warranty is the main argument when choosing a repair shop. Let's break down what obligations we take on, what to do if a fault returns, and why the price is only quoted after diagnostics.

What the 1-year warranty covers

We provide a 1-year warranty on labor and parts, including refurbished hash boards and replaced components. It covers the entire scope of work performed: soldering power circuits, replacing fans, restoring board contacts, and installed parts. If a miner shuts down due to temperature again or stops detecting a hash board a few months after service, that's a warranty case, not a reason to pay for repeat work. The obligations apply specifically to the work performed and parts installed — so the technician can go straight to the right spot. In my view, a year is enough time to reveal a soldering defect or a faulty part: power issues usually show up in the first weeks of operation under load.

What to do if the problem returns after repair

When a miner shuts down due to temperature again or loses hashrate after service, we handle it under warranty and don't charge you again. You describe the symptoms, the technician compares them with the service history and checks the exact component that was touched or replaced. A repeat visit doesn't mean a new paid case: we first rule out the warranty scenario, and only if a different fault unrelated to previous work is found, it's agreed separately. Responsibility for the result lies with the direct contractor, not an intermediary — you work with the same service that did the job. This speeds up the check and helps the technician go straight to the right spot without wasting time on re-diagnosing the entire board.

Transparency of work and price after diagnostics

The technician quotes the price after free diagnostics, once the cause of the breakdown and the scope of work are clear. Until then you pay nothing: the specialist opens the case, checks the power, hash boards and cooling, shows the defect found and explains how it will be fixed. This approach rules out a situation where the price appears at the end and turns out higher than expected. If an additional fault is found during work, we agree on it separately — no surprise extra charges at the end. You see upfront what you're paying for and can decline unnecessary work. A transparent component-by-component breakdown clears up most questions before soldering even starts: the client understands why a specific part is being replaced, not just "something inside."

What miners and components we repair

We work with miners from various manufacturers and repair not only boards but also power and cooling. Below we show what exactly is included in the scope of work and which components are checked.

Which manufacturers' miners we accept

We service Bitmain Antminer miners, including S19, L3+, L7, as well as IceRiver KS3M and other ASIC devices — not just one model. For hash boards and power, we receive both air-cooled and hydro-cooled configurations; on the S19, the most common issue is one of the chips failing, while on the L3+ it's power supply degradation after long operation under load. IceRiver models come in less often, but the logic is the same: power first, then the hash board. Even if a model is discontinued, many components — fans, power supplies, heatsinks — are interchangeable, so restoration is often possible. ASIC repair starts with checking the power and hash board. Before writing off a device, describe the exact model and what happens when you turn it on to the technician — with these two pieces of data, the chances of success are assessed more accurately.

Power supply and cooling systems

We service the power supply and cooling system separately from the hash boards, which lets us fix some failures without replacing expensive components. On the miner's power supply, we check the output voltage under load and the condition of connectors and capacitors: sagging voltage causes unstable hashrate and sudden shutdowns even when the chips themselves are fine. On the cooling side, we inspect the fans, heatsink mounting, and thermal interface: dried-out thermal paste raises chip temperatures and triggers protection, while a worn fan bearing causes noise and reduced RPM. Worn fans are best replaced as a pair or a set—if one has failed, the other is usually close to the same condition. After any power or cooling work, we always repeat the load test; otherwise, a hidden defect will show up once the miner is back home.

Component map and typical work

ComponentWhat we checkTypical workWarranty
Hash boardChips, circuit, contactsChip replacement, circuit repair1 year
Power supplyOutput voltage, connectorsRepair or replacement1 year
CoolingFans, heatsinks, thermal interfaceCleaning, fan replacement, thermal paste1 year
ControllerControl board, cablesDiagnostics, connector replacement1 year

Who will come and who to trust with your miner

When a miner stops responding, it's important to know who is actually responsible for the result. Here's how we work and who the technicians are that take on equipment restoration.

Direct contractor, not a middleman

Tech Service works as a direct contractor: our technician comes to you, and we are the ones responsible for the result—we don't hand your miner off to a third party. We have our own technicians, so there's no dispatcher between you and the person with the soldering iron who relays symptoms over the phone. This format eliminates the typical loss of information: the technician sees the device in person from the first minute instead of getting a secondhand description of the problem. We stand behind the work and the components installed, not some outside shop where the board supposedly went. When you deal with a middleman, the warranty is often provided by someone other than the person who actually did the repair—ask who will perform the work and who backs the warranty. Ask before you hand over the ASIC; otherwise, there will be no one to make a claim to.

Technicians with 4 to 20 years of experience

Our technicians have 4 to 20 years of experience, which allows them to quickly recognize common miner faults. Behind that time are hundreds of overheated hash boards, dried-out thermal pads, worn-out fans, and power supplies that sag under load. An experienced technician stands out by first ruling out simple causes—contact, overheating, power—and only then reaching for the soldering iron. This order saves your time and keeps the board intact: there's no need to heat it with a hot air gun when the issue was a loose connector. In my view, it's this discipline of sequence that distinguishes a specialist who has been fixing miners for years from someone learning on your equipment. We provide free diagnostics so the cause is identified before any work begins.

Payment and scheduling a visit

We accept Kaspi QR, Kaspi Red, card, cash or bank transfer and can arrange a technician visit within 60 minutes anywhere in the city. That means an Astana farm doesn't sit idle waiting: the technician arrives within 60 minutes and starts with an inspection. The technician quotes the cost of work after free diagnostics—until then, you don't pay for uncertainty. The visit service covers the whole city, so you don't need to haul the miner across town and risk damaging the boards in transit. The technician arrives with tools and performs the check on site. If the miner is in a farm with limited access, let the technician know in advance—this helps them prepare for the visit and avoid wasting time on site. Confirm whether there's clear access to the rack and power for testing: a couple of minutes on the phone saves half an hour of moving equipment around.

ASIC miner repair when mining stops

To sum up, here are the key points to keep in mind when your miner stops working properly and you need to decide who to trust with the repair.

  • Symptoms: it won't turn on, overheats, shows an error code, doesn't detect a hash board, or loses hashrate — each has its own cause.
  • Diagnostics: it should be free and done before any work, so the scope of repair is based on the actual findings, not guesswork.
  • Format: service can be done at your home or at the shop — choose based on the type of fault and what's convenient for you.
  • Warranty: 1-year warranty on labor and parts is a basic criterion for choosing a technician, not a nice bonus.
  • Not worth repairing: an honest technician tells you if restoration isn't feasible before starting work, not after.

7brands

Which ASIC miner brands we repair in Astana

The technician repairs mining equipment from popular brands. Choose your model to learn more.

We also repairWe also repairTECH SERVICE08

Besides ASIC miner repair, we fix other equipment in Astana

Tech Service technicians repair other appliances too — with the same 1-year warranty on labour and parts.

BlogBlogTECH SERVICE09

Worth reading before ASIC miner repair in Astana

Leave a review

Choose a platform — the TECH SERVICE page will open.

Send a review with photos on WhatsApp