Original
Original heating element
- Selection
- By part number or model
- Specs
- Power and length match the model
- Coating
- Factory coating
- Compatibility
- Guaranteed by the manufacturer
City
Language
What broke
Sections
Message on WhatsApp+7 (778) 746 00 26Mon–Fri 10:00–19:00, Sat–Sun 11:00–18:00
If your wash runs cold or the display shows a heating error, the heating element needs replacing. A technician will arrive within 60 minutes and run diagnostics.
Our own technicians4 to 20 years of experience




1 yearwarranty on labor and parts
60 minutestechnician arrival across the city
freediagnostics
The job starts with free diagnostics: the technician checks the heating element and temperature sensor and quotes the price. Then they replace the part and check water fill and heating. You get a 1-year warranty on labor and parts.
01
Step 1—
The technician checks the heating element and temperature sensor and finds out why there's no heating.
02
Step 2—
After diagnostics, they quote the price for labor and parts and confirm it with you.
03
Step 3—
They remove the old heating element, install a new one, and connect the terminals and sensor.
04
Step 4—
They check water fill and heating and make sure there are no leaks.
05
Step 5—
You get a 1-year warranty on labor and parts.
5
Five signs point to a faulty heater. If the water doesn't heat, the wash runs cold, the display shows a heating error, the program stops, or you hear crackling during heating — it's time for diagnostics.
The machine doesn't heat water
The wash runs in cold water and the laundry stays cold. Most often the cause is a burnt-out heating element.
Long wash cycle
The machine takes a long time to finish the cycle because the water temperature is low or the overheat protection kicks in.
Heating error code
The display shows a code that points to a water heating problem. Decoding the code will help the technician.
The program stops
The wash interrupts at the heating stage. The machine won't move to the next stage without heating the water.
Noise or smell during heating
You hear crackling or noise during heating, notice a burning smell, or see scale marks on the laundry.
Note the error code, the program, and when it stopped — this will speed up diagnostics. Don't take the machine apart yourself.
Describe the symptomsWe select the part by part number or machine model. For Bosch, the E-Nr is on the rating plate inside the door. The part price is given after diagnostics.
Original
or
Aftermarket
The table lists the 'from' price for labor, for common jobs also the 'from' price of the part, plus the time required to complete the job.
1–2 daystime
from 5 000 ₸cost

BeforeAfterWe reply during working hours
Leave a request — a technician will arrive within 60 minutes anywhere in the city. Diagnostics are free. You can pay via Kaspi QR, Kaspi Red, bank card, cash, or bank transfer for companies.

Warranty question? Call us
+7 (778) 746 00 266 127 reviews of repairs at TECH SERVICE in total
Григорий И.Order No. TSA-76195 · 24 July 2025
oursРасстроился сильнее, чем следовало. Проблема ровно одна: течёт. Тихо, ровно, без сюрпризов.
Эдуард К.Order No. 2502-2274 · 23 May 2025
oursПозвонил в четыре места, тут ответили по-человечески. В работе было: промышленная стиральная машина. Больше всего мешало: не отжимает. Ни копейки больше обещанного. Вскрытие показало: тэн. Работает, даже лучше прежнего
Юрий М.Order No. AS-4721 · 15 July 2024
oursИскал, кто работает в субботу, у нас с женой график сложный. Больше всего мешало: не сушит. Даже сосед заметил, что громче не стало.
Борис В.Order No. 44344 · 19 June 2023
oursБыло важно успеть до конца недели, а то морозы обещали. Отдал в сервис: промышленная стиральная машина. Симптом как на ладони: вибрация. Мастер сам предложил забрать технику на следующий день. Проверил на всех режимах — держит.
Мария Р.Order No. AS-4480 · 24 August 2021
oursДильмурат С всё сделал при мне, за пятнадцать минут. Шум ушёл, работает мягко.
Степан Я.Order No. TSA-98227 · 1 February 2021
oursХотел вызвать на дом, но в ЖК не пускают без пропуска. Основная жалоба — не сушит. Полёт нормальный.
Пётр Ч.Order No. AST-1811-567 · 2 June 2018
oursСмотрел, чтобы был свой склад запчастей, а не под заказ. Первое, что заметил: не отжимает. Tech-service посоветовали в домовом чате. Тихо, ровно, без сюрпризов.
Эвелина Ш.Order No. TSA-23656 · 4 October 2017
oursВ Астане с сервисами беда, поэтому выбирал по отзывам. Сначала списал на мороз, но нет: вибрация. Ни шума, ни запаха, всё штатно.
Инкар Д.Order No. AST-1608-336 · 22 March 2016
oursКеңседегі құрылғы, чек пен акт керек еді. Қабылдау тез болды, кезек жоқ. Бағаны алдын ала айтты, соңында өзгермеді. Түскі үзіліске қарамастан қабылдады. Мастер бәрін түсіндірді. Ескі бөлшекті көрсетіп, қайтарып берді. Достарыма айтамын.
Валерия А.Order No. 65923 · 22 March 2016
oursИскал, кто работает в субботу, у нас с женой график сложный. Честно, не ожидал, что так быстро. Больше всего мешало: течёт. Замена: подшипник. Диагностику провели при мне, ничего не унесли в подсобку. В другом месте просили на треть больше. Достойно сделали. После ремонта — как новое.
experience10 yearsSenior washing machine technician
experience16 yearsWashing machine installation technician
experience12 yearsWashing machine repair technician
experience10 yearsWashing machine board repair technician
experience11 yearsDishwasher repair technician
Didn’t find the answer? Message us on WhatsApp.
Ask a questionTechnically yes, if you have the tools and access to the heater, but on most models the heating element is located at the back or front and requires careful disassembly of the housing. Without experience, it's easy to damage the fasteners or wiring, so it's better to leave this to a technician.
Both produce a similar symptom — the water doesn't heat up — so you can't distinguish them by eye. A technician tests the heating element and checks the sensor separately, and then replaces the necessary part based on the results.
Most often due to scale and overheating if the water is hard and the machine is rarely cleaned, or because of an unsuitable part. It depends on the model: it's important that the heating element matches in power and fit.
This happens when the heating element has failed and the model doesn't display a code on the screen. The temperature sensor could also be the cause, so both components need to be checked on site.
The wash runs in cold water, the detergent dissolves poorly, clothes stay dirty, and scale builds up on the parts. It's best not to leave the heater faulty — it damages the machine.
Sometimes it's enough to remove the back or front panel and reach the heater contacts without taking the machine apart completely. But access depends on the model, and without experience it's easy to make mistakes in the measurements.

Author: Vladimir V.,Senior washing machine technician
Published
Updated
Tech Service replaces washing machine heating elements in Astana at your home: our technician arrives within 60 minutes anywhere in the city, diagnostics are free, and you get a 1-year warranty on labor and parts. The technician first checks whether the heater is actually at fault and not the temperature sensor, then selects the part by model code and replaces it on site.
Cold washing is one of the most common reasons to call a repair service, and the heater isn't always to blame. Let's look at how the causes differ and when heating element replacement in Astana is really needed.
During diagnostics, our technician checks three components one by one — the heating element, the temperature sensor, and the control module — because any of them can cause the symptom of washing in cold water. The heater itself is tested with a multimeter: if there's a break or a short to the body, it won't heat at all. The temperature sensor sits on the tank next to the heating element and reports the actual water temperature to the board — if it's faulty, the machine thinks the water is already hot and doesn't turn on the heating. The control module distributes power to the coil, and its failure is less common than the first two. Our diagnostics are free, so the technician checks all three points before naming the cause. If the machine doesn't show an error and just washes cold, the temperature sensor is more often to blame than the heating element — replacing a part blindly without a multimeter test makes no sense.
Scale is a result of hard water, and the heating element burns out due to overheating: a layer of lime prevents heat from transferring to the water, and the tube overheats from the inside. Astana's water has a lot of dissolved calcium and magnesium salts, so lime settles on the part in a dense crust faster than in regions with soft water. The crust acts as thermal insulation: the coil inside the tube gets hotter, the metal thins, and at some point a break or a short to the body occurs. The second cause of burnout is running without water: if the heater turns on with an empty tank, it fails faster than from scale. Hence the takeaway: only start a cycle with laundry loaded and don't open the door mid-wash — it's cheaper than replacing the component.
A signal on the display narrows down the search, but the interpretation depends on the model. Here's how to read heating codes and why the technician cross-checks them with the table for your machine.
On older Bosch and Siemens series (Maxx, Classixx, Logixx, Avantixx), a heating fault is F19. On some current Serie 2/4/6/8 models, the code is shown by indicators if there's no display. The same F19 on a machine with a screen reads differently than flashing lights on a panel without a display: the interpretation is tied to the specific series and set of indicators. Our technicians arrive anywhere in the city within 60 minutes, and on site they first clarify the generation — using the E-Nr label in the door or the control panel. The same combination on different generations can mean different things, so the specialist first checks the machine's series and then cross-checks the value with the table — no need to guess from an internet interpretation.
| Brand or series | Code | What it indicates |
|---|---|---|
| Bosch, Siemens, older series | F19 | Heating |
| Bosch, Siemens, older series | F18 | Drain |
| Electrolux | E20 | Drain |
| Samsung | 5E (SE, E2) | Drain |
| Indesit, Hotpoint | F05 | Drain |
The main fear owners have is that the whole machine will be taken apart at home. In reality, the technician removes one body panel and replaces the heater, and on most models doesn't touch the tank.
For most brands, we replace the heating element without removing the drum. On Bosch and Siemens, the part is at the front, so we take off the front panel instead of dismantling the whole machine. The back panel is needed when the element is mounted on the rear of the housing — there are quite a few such models on the Astana market among Indesit, Hotpoint, and some Samsung, and the technician takes this into account in advance. A split drum is found in older series, while a sealed drum is found in modern machines with a one-piece housing: on a sealed drum, the bearing is not replaced separately, but that has nothing to do with replacing the heating element. Replacing the heating element of a washing machine in Astana takes us one visit, without taking the appliance to a service center. Don't confuse the scope of work: replacing the heating element is almost always simpler than it seems and rarely requires completely disassembling the housing.
| Brand | Where the heating element is | What is removed |
|---|---|---|
| Bosch, Siemens | At the front | Front panel |
| Most brands | At the back or front | Panel without removing the drum |
| Sealed drum | Depends on the model | Drum is not touched when replacing the heating element |
We select the heating element by part number or model code. For Bosch, we take the E-Nr from the label in the door — this way the part matches the machine without trial fitting. For other manufacturers, the model code is on the nameplate on the back of the housing, and it shows the mounting location, length, and power of the heating element. The power and length of the heating element vary between models, so a universal heating element from the market often doesn't fit the mounting location and the sensor hole. Our technicians have been working with these appliances for 4 to 20 years and verify the part before the visit, so they don't bring two or three versions to choose from and don't delay the repair.
Response time and warranty are what owners look at before requesting service. Here's how the visit works, what warranty terms apply, and when the price is quoted.
A Tech Service specialist arrives within 60 minutes anywhere in the city, and diagnostics on site are free — you pay only for the work and the part after approval. The visit is at your home: you don't need to transport or load the machine, and the check is done under normal conditions — on site, you can see where the appliance is and how it's connected to water and drainage. After the inspection, the specialist names the cause and proposes a plan for further work. Our employee, the direct contractor, comes to you, not an intermediary, so there are no extra links between you and the repair. A home visit is more convenient than a service center: you don't need to set aside half a day for the trip and return delivery. Before the visit, clear access to the machine and have the model ready — the specialist will use it to verify the needed part in advance.
We provide a 1-year warranty on labor and parts for heating element replacement, and the price is quoted after free diagnostics — before work begins. You can pay via Kaspi QR, Kaspi Red, bank card, cash, or bank transfer for companies: cash, card, transfer. Replacing the heating element for most brands is done without removing the drum, so the agreed scope includes exactly this operation, without unnecessary disassembly of the housing. The warranty on the part is just as important as the warranty on the work: if the new heating element fails, it is replaced under warranty, not at your expense. In our practice, technicians with 4 to 20 years of experience first verify the model code and part number, and only then quote the final price. Before work begins, ask exactly which operations are covered by the warranty and for what period it is issued — this way you protect yourself from disputes.
While the technician is on the way, it's important not to make things worse. Let's go over whether you can do laundry with a non-working heating element and how to prepare yourself so the specialist's visit goes smoothly.
You can still wash with a faulty heating element, but your laundry won't come out as clean: detergent doesn't fully dissolve in cold water, and stains can remain on the fabric. A cold wash doesn't trigger the heating cycle, so the machine simply runs without heating the water—the drum and drain are still working fine. Constantly washing in cold water won't kill the machine right away, but don't put off diagnostics: the cause might not be the heating element but the control board, and delaying can cost you more. We recommend unplugging the machine before the technician arrives if the cycle keeps interrupting or you notice a smell. In my opinion, a couple of days of cold washes won't do any harm, but repeatedly trying to start the heating with a faulty component is an unnecessary risk for the board.
Here are the key points for washing machine owners dealing with cold washes—from making a diagnosis to preparing for the technician's visit.
If you ask, the technician will check other parts during the same visit.
Refrigerator Repair in Almatyfrom 3 000 ₸
Dishwasher Repair in Almatyfrom 3 500 ₸
Oven Repair in Almatyfrom 3 000 ₸
Cooktop Repair in Almatyfrom 3 500 ₸
Air Conditioner Repair in Almatyfrom 3 500 ₸
Boiler and Water Heater Repair in Almatyfrom 2 500 ₸
Freezer Repair in Almatyfrom 6 000 ₸
Tumble Dryer Repair in Almatyfrom 5 000 ₸
A washing machine can hum for many reasons, and the first thing to figure out is when the sound appears.
20 March 2026 · 12 minutes read
If your washing machine isn't filling with water, the most common culprits are a closed valve, a clogged inlet filter screen on the hose…
20 February 2026 · 13 minutes read
Washing machine error codes are self-diagnostic codes that point to a specific component: drain, water fill, heating, motor, or door lock.
29 January 2026 · 13 minutes read
If your washing machine won't spin, it's usually an unbalanced load, a clogged drain filter or hose, and less often the pump, belt…
19 January 2026 · 12 minutes read
If your washing machine isn't heating water, the heating element or temperature sensor is usually to blame, less often the control board or wiring.
25 December 2025 · 12 minutes read
If your washing machine won't turn on, first check the outlet, extension cord, and the circuit breaker in your panel, then the plug and power cord.
24 November 2025 · 13 minutes read