Original
Strips with factory markings
- Selection
- By strip number or TV model
- Match
- Markings and specs match the factory ones
- Lead time
- Depends on supplier availability
- Price
- After diagnostics
City
Language
What broke
Sections
Message on WhatsApp+7 (778) 096 59 61Mon–Fri 10:00–19:00, Sat–Sun 11:00–18:00
A technician arrives within 60 minutes anywhere in the city, and diagnostics are free. We work with panels of all sizes.
Our own technicians4 to 20 years of experience




1 yearwarranty on labor and parts
60 minutestechnician arrival anywhere in the city
freediagnostics
The technician removes the back cover, takes out the panel, and checks the strips and driver. After replacing the LED strips or lenses, the panel is reassembled and checked for even lighting. The price is quoted after free diagnostics.
01
Step 1—
The technician carefully removes the cover and keeps the screws organized so the case isn't damaged during reassembly.
02
Step 2—
The panel is handled with extra care: it's fragile and must not be bent or dropped.
03
Step 3—
The technician tests the LED strips and measures the driver's power output to find the faulty component.
04
Step 4—
New strips are installed, or lenses are replaced if they've become cloudy or shifted.
05
Step 5—
The TV is reassembled and turned on: the technician checks that the lighting is even across the entire screen.
5
Five typical symptoms point to the backlight: a dim screen, spots, stripes, flickering, and failure to light up. Unusual sounds when turning on are not related to the backlight.
Uneven brightness across zones
Part of the screen is dimmer — this is how a group of LEDs burning out looks, unlike uniform dimming.
Light border along the screen edge
Edge lighting appears when the diffuser or reflective film has shifted during a previous disassembly.
Screen lights up but no image
The backlight works, but no signal reaches the panel; this is a separate issue that is checked before disassembling the panel.
Doesn't turn on the first time
After pressing again, the screen lights up normally; this indicates drifting driver parameters, not LED failure.
Unusual sound
Clicking or humming when turning on is not related to the backlight: the source is the power supply or mounting.
Take a photo of the defect on the screen and note the conditions when it appears — after warming up, when cold, on a light background.
Describe the symptomsStrips are selected by part number or TV model. The number of LEDs, length, connector, and lenses all matter.
Original
or
Analog
The table lists the 'from' price for labor, for common jobs also the 'from' price of the part, plus the time required to complete the job.
1 visittime
from 9 000 ₸cost

BeforeAfterWe reply during working hours
Describe how the screen behaves when you turn it on — the technician will tell you whether the strips need replacing or just the driver needs checking.

Warranty question? Call us
+7 (778) 096 59 616 127 reviews of repairs at TECH SERVICE in total
Геннадий Ж.Order No. TSA-97667 · 31 December 2025
oursСмотрел, чтобы был свой склад запчастей, а не под заказ. С чем обратился: нет картинки. Работает, даже лучше прежнего)
Аркадий Я.Order No. TSA-51948 · 3 June 2023
oursПроблема ровно одна: полосы. Сергей Архипов показал старую деталь, всё прозрачно. Прошивка та же, ничего не сбросили)
Альбина Ю.Order No. 2102-9424 · 27 July 2021
oursСосед по площадке хвалил, решил проверить. Записался на ремонт спутникового ресивера. С чем обратился: нет сигнала. Пришлось ставить: блок питания. Отдал 26 500 и не жалею. Приняли, объяснили, что и почему, без спешки. Пришлось самому напомнить о себе. Скажу знакомым. Дома включил, всё на месте!!
Яна Э.Order No. 69854 · 11 February 2021
oursТехника на балансе ТОО, нужен был чек и акт. Вчера работало, сегодня уже нет картинки. Ответили в мессенджере, потом созвонились. Полёт нормальный.
Ульяна Ч.Order No. AS-4939 · 25 April 2018
oursБыло важно успеть до конца недели, а то морозы обещали. Думал, показалось, ан нет: полосы. Сейчас пашет без нареканий.
Наталия С.Order No. AS-9915 · 19 August 2017
oursЗаявку оставил через сайт вечером, утром перезвонили. Думал, попал на дорогой ремонт. Проблема ровно одна: не включается. Сергей Архипов отсоветовал дорогой ремонт, предложил простой. Полёт нормальный!!
Семён Ш.Order No. 1607-9298 · 17 October 2016
oursПервое, что заметил: не включается. Дамир М не пропал после ремонта, помог с настройкой. Пользуюсь и вспоминаю добрым словом.
Эвелина Ш.Order No. ZK-2016-205 · 24 July 2016
oursСосед по площадке хвалил, решил проверить. Проблема ровно одна: зависает. Сейчас пашет без нареканий.
Елизавета Л.Order No. 1609-3170 · 16 July 2016
oursИскал, кто работает в субботу, у нас с женой график сложный. Причина обращения — не включается. Разъёмы на месте, ничего не люфтит.
Айжан Б.Order No. ZK-2016-471 · 2 March 2016
oursТелефонмен кеңестім, кейін апардым. Барлығы ресми, чек берді. Ақауын тез анықтады, қажетсіз нәрсе ұсынбады. Жақсы сервис!!
experience10 yearsTV screen replacement technician
experience7 yearsLead electronics repair technician
experience10 yearsMobile PC repair technician
experience10 yearsLaptop repair and assessment technician
experience15 yearsDigital device repair technician
Didn’t find the answer? Message us on WhatsApp.
Ask a questionYes, in most cases the technician replaces the backlight at your home. This is possible if the model allows it and there's a convenient place to disassemble the TV. If complex repair is needed, the TV is taken to the service center.
A dim picture after replacing the backlight is most often because the new LED strips differ in specs from the old ones, or the brightness is set incorrectly in the settings. Another cause can be a loose connection of the ribbon cable to the control board or damage to the backlight driver. In such cases, re-diagnosis and a compatibility check of the installed parts are needed.
Yes, our technicians repair backlights on TVs from popular brands, including Samsung, LG, Sony, TCL, Hisense. We work with various models, selecting suitable components.
Most often this indicates a fault in the LEDs or power supply. During overheating or a voltage surge, the backlight turns off for protection. Free diagnostics will determine the exact cause.
Such symptoms usually indicate backlight problems: uneven glow or partial LED shutdown. But other causes are possible, so diagnostics are needed. The technician will check and identify the exact cause.
Replacing the entire strip is more reliable: new LEDs will last longer, and the brightness will be even. Resoldering individual elements is possible, but often a temporary fix. The choice depends on the model and condition of the backlight.

Author: Oraza B.,TV screen replacement technician
Published
Updated
Tech Service replaces TV backlights in Astana at your home or in our service center: a technician arrives within 60 minutes anywhere in the city, diagnostics are free, and you get a 1-year warranty on labor and parts. The technician first checks whether the issue is the backlight or the matrix, then agrees on the scope of work and gives you the price.
Backlight and matrix failures look similar but are fixed differently. Here's how a technician tells them apart before taking anything apart.
If the TV turns on, you hear sound, but the screen is black, the matrix is usually fine and the backlight has failed. LED strips sit behind diffuser layers and light the pixels from behind or along the edges, with a driver supplying voltage; when the strip or the control board stops working, the picture disappears but the audio and tuner keep running. Shine a flashlight close to the screen at an angle — if you can see a faint picture in the light spot, the matrix works and the problem is in the LED strips or driver. The same test can reveal pixel defects: solid dead zones and rainbow streaks instead of a uniform image point to the panel itself. Check in a dark room — in daylight the difference between a faint picture and a black screen is almost invisible. If the test confirms a strip problem, you'll need TV backlight replacement — in Astana we do it after a free diagnostic.
A backlight that goes off a couple of seconds after turning on, flickers when scenes change, or shows dark spots and stripes at the edges almost always points to degraded LEDs or a faulty driver. LEDs in a strip are connected in series, and one degraded chip drags down the whole chain: the TV starts, but protection shuts off the backlight as soon as the voltage crosses the threshold. Flickering on bright scenes is the same mechanism, just triggered under load rather than immediately. Spots and stripes at the edges are locally burned-out LEDs in the strip; if you delay repair, the driver runs overloaded and may fail along with the strips. During the free diagnostic, the technician checks the chain zone by zone and separates strip degradation from a board fault so you don't replace working parts.
Here's what happens step by step from request to checking the picture after replacement, and when we work at your home versus in the service center.
Most TVs up to 55 inches we replace at your home, while larger panels are easier to disassemble at the service center. On-site, the technician needs clear access to the back cover and a flat surface — the TV is taken off the wall or turned face down on a table. Panels from 65 inches are heavier and need more space for disassembly, so it's safer to transport them to the workshop and reassemble there. TV backlight repair cost depends on where the work is done — at home or at the service center — and the technician gives you the price after a free diagnostic. We agree on a specific time in advance so the technician arrives when the TV is already accessible. If the device is already off the wall and lying on the floor, that doesn't prevent a visit — we work with it in whatever position it's in. For large screens, transporting to the service center is more convenient: the workshop has enough space for careful panel disassembly.
Both options restore the backlight, but they suit different cases. We'll show what determines the choice and what we check after the repair.
| Option | When we use it | What we replace | What we check afterwards |
|---|---|---|---|
| LED resoldering | 1–2 LEDs burned out, the rest are fine | Individual LEDs | Even glow across the entire panel |
| Full strip replacement | Several LEDs burned out in a row or the strip has degraded | LED strips | Glow and absence of spots |
| Driver replacement | Strips are intact but the backlight won't start | Backlight driver | Stable startup and brightness |
If the image remains dim after backlight repair, the cause is in another component — most often the driver or power supply — and we check them during a follow-up diagnosis. The backlight driver sets the voltage for the LED strips, while the power supply handles the overall power to the board; a drop in either one causes a dim screen even with new LEDs. During the follow-up diagnosis, the technician measures the driver's output voltage, compares it with the specification for the specific model, and checks the ribbon cable contacts for oxidation. Dimness after repair is more often related to the driver than to a new strip. Repeat dimness is not a reason to replace the TV: in most cases, it's enough to refine the driver. That's why we conduct the follow-up diagnosis carefully and check all components that affect brightness.
The backlight is designed similarly in most LCD and LED TVs, but different brands have their own strips, connectors, and mounts. We'll tell you which brands our technician works with and how this affects the repair.
We repair Samsung and LG panels in Astana either on-site or at the service center, depending on the diagonal and body design. In models of these brands, LED bars are often held by snap-on clips without screws, and careless disassembly can break the plastic fasteners. We disassemble compact panels on-site where the body can be removed without risk to the matrix. Large screens with fragile clips are taken to the service center — there the panel is laid on a flat surface and worked on without haste. Diagnostics are free, a technician visit within the city takes 60 minutes, and the warranty on labor and parts is 1 year. Before disassembly, the technician marks the position of the bars to reassemble the panel in the original order and avoid extra gaps.
We'll explain exactly what the warranty covers, how payment for the work is handled, and in which cases backlight repair is more cost-effective than buying a new TV — with facts about timelines and conditions.
1-year warranty — we provide a 1-year warranty on labor and parts: if the backlight starts to go out or flicker again during this period, a technician will come back. Our experience in TV repair ranges from 4 to 20 years among our staff, and over this time we've seen that the weak point is often not the strip itself but the contact on the ribbon cable or the driver that powers it. That's why during diagnostics we check not only the strip but also these components — it's more reliable that way. The 1-year warranty covers labor and parts — when choosing a repair option, you don't have to worry that a more affordable one will be less reliable. In case of a warranty claim, just describe the symptom, and we'll arrange a repeat visit in the city — the technician arrives within 60 minutes.
We accept payment via Kaspi QR, Kaspi Red (instalments), bank card, cash, or bank transfer for companies, and the technician gives you the price after free diagnostics. This order is convenient: first he opens the panel, checks the power supply, ribbon cables, and the LEDs themselves, and only then quotes the TV backlight repair — the cost depends on the fault found. Backlight repair makes sense when the matrix is intact and other components work: replacing the strip or re-soldering the LEDs brings back to life a panel that would otherwise have to be replaced entirely. If there are cracks or stripes on the screen from a mechanical impact, a new device will be cheaper — the technician will tell you this right during diagnostics, without pushing a job the panel won't survive. This approach saves time and money: you know in advance whether it's worth investing in repair or better to put the money toward new equipment.
Backlight replacement restores the picture on a TV with an intact matrix. Below is a short summary to help you decide without unnecessary doubts and extra costs.
If you ask, the technician will check other parts during the same visit.

If your TV won't turn on, first check the outlet, power cable, and the button on the TV itself—not the remote.
21 November 2025 · 12 minutes read
If your laptop screen is broken, turn the device off first, don't press on the display, and check the picture through an external monitor.
12 March 2026 · 11 minutes read
If your phone won't charge, start by checking the adapter, cable, and port, then the charging settings.
16 February 2026 · 12 minutes read
If your laptop freezes, the first thing to do is restart it and check Task Manager to see what's loading the CPU and memory.
25 January 2026 · 12 minutes read
If your phone falls in water, take it out right away, turn it off, and don't charge it.
19 January 2026 · 12 minutes read
If your phone camera isn't working, first check app permissions, clear the cache, and restart your phone — this fixes some software glitches.
24 December 2025 · 13 minutes read





