Геннадий Ж.Order No. TSA-74427 · 1 November 2026
oursПереезжали в новую квартиру, техника после перевозки захандрила. Жалоба одна: не держит температуру. Внешне не видно, что разбирали
City
Language
What broke
Sections
Message on WhatsApp+7 (778) 746 00 26Mon–Fri 10:00–19:00, Sat–Sun 11:00–18:00
A technician arrives within 60 minutes anywhere in the city. Diagnostics are free.
Our own technicians4 to 20 years of experience




Repair prices
Symptoms and likely causes. The technician confirms the exact cause after free diagnostics.
refrigerant leak, compressor, thermostat
from8 000 ₸
drain, door seal, hoses
from3 000 ₸
fan, compressor, mounting
from27 500 ₸
door seal, defrost, sensor
from6 000 ₸
power supply, control board, start relay
from17 500 ₸
thermostat, sensor, control board
from9 500 ₸
hinges, door seal
from10 000 ₸
the code points to a specific unit
from17 500 ₸
The table lists the 'from' price for labor, for common jobs also the 'from' price of the part, plus the time required to complete the job.
1 visittime
from 6,000 ₸cost

BeforeAfter5 steps

From your request to a final check — five steps.
What we ask when you request service — address, floor, access to the display case, and a convenient visit time.
What the technician does before arriving — reviews your request by model and selects typical parts for your display case.
The technician finds the cause and gives you the repair cost before any work begins.
Discuss with the technician which parts will be replaced, what will be left for preventive maintenance, and ask questions before work starts.
How to accept the display case after repair by checking the thermometer readings and the condition of the door seal.
We reply during working hours
Describe the display case model and the symptom when you request service so the technician brings the right parts. A technician arrives within 60 minutes anywhere in the city.

Warranty question? Call us
+7 (778) 746 00 266 127 reviews of repairs at TECH SERVICE in total
Геннадий Ж.Order No. TSA-74427 · 1 November 2026
oursПереезжали в новую квартиру, техника после перевозки захандрила. Жалоба одна: не держит температуру. Внешне не видно, что разбирали
Вадим Г.Order No. 27170 · 6 May 2025
oursЗнакомый мастер раньше здесь работал, дал номер. Вчера работало, сегодня уже не держит температуру. Ни разу не пожалел.
Регина Ф.Order No. TSA-59951 · 10 March 2025
oursЗнакомый мастер раньше здесь работал, дал номер. Ни с того ни с сего — шумит. Вскрытие показало: вентилятор. Сказали 17 000 по телефону, столько и вышло. Всё быстро, но без суеты. Приятно удивлён. Гудит ровно, не перегревается.
Темирлан Ц.Order No. AS-3823 · 9 November 2024
oursКүтуге уақытым аз еді, сол күні бітірді. Ақауын тез анықтады, қажетсіз нәрсе ұсынбады. Бағаны алдын ала айтты, соңында өзгермеді. Түскі үзіліске қарамастан қабылдады. Нәтижесіне ризамын.
Римма Х.Order No. AS-3178 · 14 July 2024
oursПричина обращения — шумит. Никита М сам позвонил и сказал, что готово. Позвонил в Tech-service по номеру из 2ГИС. Третий месяц — никаких проблем.
Инна Н.Order No. AS-1071 · 16 February 2024
oursСосед по площадке хвалил, решил проверить. После скачка напряжения — шумит. Функционирует, тьфу-тьфу.
Константин О.Order No. ZK-2022-611 · 26 December 2022
oursСмотрел, чтобы был свой склад запчастей, а не под заказ. С этим и пришёл: шумит. Третий месяц — никаких проблем.
Борис В.Order No. ZK-2022-685 · 22 November 2022
oursХотел вызвать на дом, но в ЖК не пускают без пропуска. С чем обратился: шумит. Внешне не видно, что разбирали.
Вера Э.Order No. AST-2212-894 · 13 January 2022
oursВыбирал между официальным и этим, выбрал этот. Думал, попал на дорогой ремонт. Основная жалоба — шумит. Всё быстро, но без суеты. По деньгам вышло ровно, без сюрпризов. Замена: вентилятор. Работает, как будто и не ломалось!!
Альмира П.Order No. AS-4147 · 18 November 2020
oursТелефонмен кеңестім, кейін апардым. Кепілдік берді, бұл маңызды. Түскі үзіліске қарамастан қабылдады. Бағаны алдын ала айтты, соңында өзгермеді. Ақауын тез анықтады, қажетсіз нәрсе ұсынбады. Бөлшек қоймада бар екен, күтпедік. Жұмысты сол күні аяқтады. Ескі бөлшекті көрсетіп, қайтарып берді. Бағасы мен сапасы сай.
Леонид П.Order No. AS-8385 · 3 August 2020
oursОфис на Кабанбай батыра, технику туда и повёз. Думал, показалось, ан нет: течёт. Никита М принял без вопросов, хотя был без записи. Замена: вентилятор. В другом месте просили на треть больше. Позвонил, объяснил, сказали подъезжать — примут без записи. Доволен, если коротко. Полёт нормальный.
Эдуард К.Order No. AST-1801-413 · 28 July 2018
oursВыбирал между официальным и этим, выбрал этот. Настроение было — хуже некуда. Больше всего мешало: течёт. Дильмурат С объяснял без умных слов, за это спасибо. Ни разу не пожалел.
Галина Ф.Order No. AS-1845 · 15 June 2018
oursПереезжали в новую квартиру, техника после перевозки захандрила. Проверил всё, что мог: шумит. Оплату взяли после ремонта, а не вперёд. Нужна была новая деталь: термостат. Ни копейки больше обещанного. Шум ушёл, роботает мягко)
experience11 yearsDishwasher repair technician
experience10 yearsSenior washing machine technician
experience11 yearsStove and oven repair technician
experience11 yearsFreezer repair technician
experience16 yearsWashing machine installation technician
experience8 yearsDishwasher technician
experience12 yearsWashing machine repair technician
experience10 yearsWashing machine board repair technician
Didn’t find the answer? Message us on WhatsApp.
Ask a questionIf the display case isn't cooling, the motor hums in bursts or is silent, and the compressor body stays cold, the compressor has likely failed. More often, the thermostat causes the display case to run nonstop. A technician will make an accurate diagnosis after free diagnostics.
With Tech Service, a technician arrives right at your sales floor in Astana within 60 minutes. Diagnostics are free; after that, they outline the scope of work and the cost and start the repair on site right away.
Display cases with heavy loads and nonstop operation tend to break down more often, especially in hot weather. Compressor wear, refrigerant leaks, and drain clogs occur across many brands. It depends on the model and operating conditions.
Water at the bottom appears when the drain hole is clogged or the condensate drain tube is displaced. Sometimes the cause is a crack in the tray or ice buildup on the evaporator. A technician will clear the drain and check the defrost system to fix the root cause.
Most jobs—replacing the gasket, relay, thermostat, cleaning the drain, recharging refrigerant—are done right on the sales floor. The display case is taken to the service center only for complex compressor or control board repairs. The technician will confirm after diagnostics.
If the body and glass are intact and the breakdown involves a single component, repair is usually more cost-effective. Replacement makes sense with through corrosion, cracks in the chamber, or when several major components fail at once. The technician will help compare options after diagnostics.
Tech Service repairs display refrigerators in Astana as a direct contractor: our technician arrives on site within 60 minutes anywhere in the city, diagnostics are free, and there is a 1-year warranty on labor and parts. We work with commercial refrigeration for shops and cafes, and we repair on site without taking the display away.
A display case is commercial equipment, not a home refrigerator: it has a different design, different components, and a different cost of downtime, so repairs are done differently than household appliance service.
A display case stands in the sales area by a window or entrance; in summer the condenser works under increased load, and the compressor and fan wear out faster than in a household refrigerator in a cool kitchen. In the sales area, heat from customers, lights, and open doors never stops all day, and the rear grille is often placed right against the wall or blocked by boxes. As a result, heat dissipation drops, the unit maintains high pressure longer and hums louder. The equipment almost never turns off: not all models have a night curtain mode, and after the shift the equipment keeps freezing products until morning. A home refrigerator is opened less often and kept in a room with a stable temperature. If the display case hums louder than usual, this is often the first sign of a clogged or poorly ventilated condenser, not "normal operation" — this symptom should be looked at before it stops cooling.
For a shop or cafe, display case downtime means spoiled goods and lost revenue, so we arrive on site within 60 minutes anywhere in the city and try to complete the work on site. While the equipment is not holding cold, perishables in the trays warm up, and the display has to be urgently moved to a back-room refrigerator or taken off sale. In our practice, the technician arrives on site with tools, and diagnostics are free: the cause becomes clear before work begins. A display case can stand unattended in the sales area all shift, and every hour of warm downtime adds to product write-offs. The longer the equipment stays warm, the more items will have to be discarded, so it is better not to postpone diagnostics and repair until "after the shift" but to start as soon as the temperature starts to drift.
By the symptom, you can usually guess which component of the display case has failed and understand how urgently a technician is needed. Below are the most common complaints and what lies behind them.
If the LED lighting works but there's no cold, it's usually a refrigerant leak, a faulty compressor, or a start relay — the display gets power, but the refrigeration circuit doesn't start. A freon leak shows up gradually: first the display holds cold worse during peak load hours, then it stops freezing altogether, while the condenser stays cold. A compressor with worn windings hums and clicks but doesn't reach operating mode, and a burnt start relay cuts off the motor a few seconds after start. The technician checks the circuit pressure, compressor current draw, and winding resistance — these three measurements rule out most possibilities in one visit. If you need display refrigerator repair in Astana, such measurements help pinpoint the faulty component. The lit lighting says nothing about the circuit's condition: light and cold in the display are powered and operate separately, so "light on" doesn't mean "display is fine."
Running without stopping is usually linked to the thermostat or temperature sensor, while water at the bottom comes from a clogged or frozen condensate drain system. The thermostat controls compressor on/off: if its contacts stick or the sensor sends inflated readings, the unit freezes continuously and the evaporator ices up. Water appears when the drain is clogged with crumbs and product packaging or the drain tube freezes — condensate doesn't flow into the pan and stays at the bottom of the chamber. Diagnostics take little time: the technician tests the sensor, checks the thermostat setting, and blows out the drain. If the display doesn't turn off, the compressor wears out faster, so "let it run for now" is a bad strategy: a component that could still be adjusted will eventually need replacement.
| Symptom | Likely cause | What the technician checks |
|---|---|---|
| Not freezing, light on | Freon leak, compressor, start relay | Circuit, compressor, relay |
| Doesn't turn off | Thermostat, temperature sensor | Sensors, shutdown cycle |
| Water at the bottom | Condensate drain system | Drain, freezing |
| Ice buildup, door doesn't seal | Gasket, hinges | Seal, hinges, closers |
| Hums louder than usual | Fan, condenser | Airflow, condenser contamination |
| Uneven cold | Fan, evaporator | Air circulation |
The combination of symbols on the display screen is a hint from the electronics about which component is out of operating parameters. Such a hint narrows the search but doesn't replace diagnostics.
The control board generates the signal when the thermistor, compressor, or fan goes beyond acceptable parameters, and it shows the technician which way to look. The electronics read from the evaporator thermistor, the air thermistor in the chamber, and the compressor start relay, compare them with factory thresholds, and when they go out of bounds, display an alphanumeric combination on the screen. For displays with an electronic controller, the signal is accompanied by a sound and a flashing indicator; models with a mechanical thermostat have no combination at all — there, only the unit's behavior and ice buildup reveal the fault. The combination on the screen doesn't always point to the broken component itself — sometimes it signals a consequence, such as overheating due to a clogged condenser, so the technician checks both the source and the effect.
The decoding depends on the display case model and its controller, so the same combination on two different units can point to different components. For one brand, E1 means a failed air thermistor; for another, it's an open evaporator circuit; for a third, it's exceeding the time to reach set mode. Different manufacturers number faults according to their own logic: sometimes it's Latin letters with a number, sometimes just a number, and on budget controllers the same symbol can mean both overheating and a broken sensor. If you look for the cause only using an online table, you can easily replace a working part, so the technician first checks the value against the display case model and then tests the component live. This approach saves both time and parts: replacing a working element doesn't fix overheating, it just delays another breakdown.
We fix most breakdowns right in the store or cafe without taking the equipment away. Below is how it works and what to do with the products during the work.
The time depends on which component failed: adjusting the door and replacing the seal take less time than finding a refrigerant leak or replacing the compressor. Door mechanics is the fastest scenario: remove the old seal, adjust the hinges and closer. Finding a leak takes longer because the technician checks the circuit step by step, and after fixing it, a recharge is required. Compressor replacement is the most labor-intensive work: you need to free access to the unit and check the circuit for leaks. Before any work, we perform free diagnostics: before that, it's unknown whether a refrigerant recharge is needed or just adjusting the door mechanics is enough. The technician gives the exact time after diagnostics when the component and scope of work are clear. From our team's experience, finding a hidden leak in the foamed part of the circuit takes the longest.
Not every breakdown of a refrigeration cabinet is worth fixing, and not every old unit should be written off. Let's look at the signs a technician and owner use to decide.
Repair is justified if one component has failed — compressor, relay, thermostat, gasket, or hinges — while the body, glass, and circuit are otherwise intact. A targeted replacement of the compressor, start relay, or thermostat gets the cabinet working again without affecting the rest of the structure: the power unit gets a new service life, while the frame and panels stay the same. The gasket and hinges are replaced separately when the door no longer closes tightly and warm air gets inside — this makes the compressor run longer and heat up more. During diagnostics, the technician checks each component in turn to avoid missing a hidden fault next to the obvious one: for example, a burnt relay often masks early motor wear. We replace the part, blow out the circuit, check the cooling cycle after reassembly, and measure the temperature on the shelves. A targeted part replacement extends the display case's life for years, whereas trying to run it until full wear usually ends in several breakdowns in a row.
Replacement is usually more cost-effective if not one but several components are worn out, or when the model is rare and parts are hard to find. The compressor, control board, and cooling circuit wear out together, and fixing one element only delays the next failure: while the cabinet is idle, products have to be moved elsewhere. For rare models, finding the right part delays the work, and compatible components perform differently from original ones — the temperature on the shelves suffers. The decision should be based not on the display case's age but on the combination of breakdowns: if the compressor, then the board, then the circuit fail within a short time, repairs become an endless expense. In such a situation, a new unit is more predictable — it won't require investment in the near future and runs on original parts.
After free diagnostics, we tell you straight what has failed, what work is needed, and whether it's worth investing in restoring this display case. Our technician arrives on site within 60 minutes anywhere in the city, inspects the components, and quotes the cost of work after diagnostics — before you decide to repair or replace. Specialists with 4 to 20 years of experience can tell the difference between a case where replacing one compressor solves the problem and a case where the equipment itself needs replacing. We don't push work that won't pay off, and we don't rush replacement of a unit that is essentially working. A 1-year warranty on labor and parts applies even after a targeted repair, so choosing to repair doesn't leave you without support. An honest assessment during diagnostics saves money: sometimes it's cheaper to replace the display case once than to return to the same component three times in a season.
For a store owner, it's important to understand who exactly will come on site, what the display case inspection includes, and what happens if the breakdown recurs. Below is how our work is organized.
Our diagnostics are free: a technician comes to your location, checks the display case, finds the cause of the breakdown, and gives you the cost of work before starting. A visit within the city takes up to 60 minutes. The specialist inspects the compressor, refrigerant circuit, thermostat, and sensors, checks airflow and defrost, and listens to the evaporator fans. Based on the results, they explain which component failed and what restoration options are available—from a targeted part replacement to more extensive work. You make the decision with the full picture, with no obligation. Free diagnostics removes the main risk for a store—paying for a visit and finding out that restoration isn't feasible—so the discussion about work is specific, not blind.
We provide a 1-year warranty on labor and parts: if the repaired display case component fails again due to our fault, we'll come back and fix it. This covers both replaced parts—compressor, thermostat, fan, sensor—and the quality of the assembly and connection itself. The technician who handled your location knows the history of that specific display case, so a follow-up visit is faster than the initial one. A warranty on parts is just as important as a warranty on labor: a faulty part may not show up immediately, and the store owner needs to know that this risk is covered. Over 4–20 years of our technicians' practice, we've seen how a cheap part replacement without a warranty led to another display case breakdown during peak season.
Tech Service is a direct contractor: our technician comes to you, not a subcontractor through an aggregator, and the service itself is responsible for the work and warranty. This means the person who inspects the display case also services it—no handing off the job down the chain. Our specialists have 4 to 20 years of experience with commercial refrigeration, know the designs of various display case types, and are familiar with typical component failures. When there's no intermediary between you and the technician, information about the breakdown isn't lost and responsibility isn't blurred if something goes wrong after the work. In my opinion, this is a decisive factor for a store: the display case is down, products lose their appearance, and every extra handoff of the request means an additional hour of downtime.
A display refrigerator is more complex than a household one, and it has its own types of breakdowns. Below is a quick summary to help a store owner get oriented before the technician arrives.
90brands
We work with every brand sold in Kazakhstan — from Samsung, LG and Atlant to Biryusa, Indesit, Stinol and rare imported makes. Can’t find yours in the list? Call anyway — a technician will come and take a look.
Tech Service technicians repair other appliances too — with the same 1-year warranty on labour and parts.
Refrigerator Repair in Almatyfrom 3 000 ₸
Washing Machine Repair in Almatyfrom 3 000 ₸
Dishwasher Repair in Almatyfrom 3 500 ₸
Oven Repair in Almatyfrom 3 000 ₸
Cooktop Repair in Almatyfrom 3 500 ₸
Air Conditioner Repair in Almatyfrom 3 500 ₸
Boiler and Water Heater Repair in Almatyfrom 2 500 ₸
Freezer Repair in Almatyfrom 6 000 ₸
Tumble Dryer Repair in Almatyfrom 5 000 ₸
Coffee Machine Repair in Almatyfrom 2 500 ₸
Robot Vacuum Cleaner Repair in Almatyfrom 3 500 ₸
Vacuum Cleaner Repair in Almatyfrom 1 500 ₸
Microwave Oven Repair in Almatyfrom 2 000 ₸
Hair Dryer Repair in Almatyfrom 1 500 ₸
Iron Repair in Almatyfrom 3 000 ₸
Electric Kettle Repair in Almatyfrom 2 500 ₸
Mixer Repair in Almatyfrom 2 500 ₸
Multicooker Repair in Almatyfrom 500 ₸
If your refrigerator stops working, first check the outlet, the power cord, and the thermostat setting, and after defrosting let it stand for a while.
4 February 2026 · 12 minutes read
If your refrigerator isn't cooling but the light is on, the cause is usually one of the components in the cooling circuit: the compressor, thermostat…
10 December 2025 · 13 minutes read
If your dishwasher won't drain, the most common culprits are a clogged filter or drain hose; less often, it's the pump, impeller…
24 March 2026 · 12 minutes read
A washing machine can hum for many reasons, and the first thing to figure out is when the sound appears.
20 March 2026 · 12 minutes read
If your washing machine isn't filling with water, the most common culprits are a closed valve, a clogged inlet filter screen on the hose…
20 February 2026 · 13 minutes read
If your microwave isn't heating but the light and turntable still work, the problem is usually one of the high-voltage components — the magnetron, diode…
15 February 2026 · 12 minutes read












