Иван Н.Order No. ZK-2026-208 · 31 August 2026
oursСосед по площадке хвалил, решил проверить. С чем обратился: не едет. Третий месяц — никаких проблем.
City
Language
What broke
Sections
Message on WhatsApp+7 (778) 096 59 61Mon–Fri 10:00–19:00, Sat–Sun 11:00–18:00
A technician arrives within 60 minutes anywhere in the city. Free diagnostics, 1-year warranty on labor and parts.
Our own technicians4 to 20 years of experience




Repair prices
Symptom and the component checked first.
battery, fuse, lock
from12 000 ₸
PAS sensor, throttle, controller
from6 500 ₸
cell wear, cold, faulty charger
from12 000 ₸
bearing, gear wear, play
from8 500 ₸
overload, moisture, short circuit
from13 500 ₸
overload, poor contact, settings
from13 500 ₸
wear, squealing, reduced braking
from2 500 ₸
bearing wear, loose fasteners
from11 000 ₸
The table lists the 'from' price for labor, for common jobs also the 'from' price of the part, plus the time required to complete the job.
1–2 hourstime
from 2,500 ₸cost

BeforeAfter5 steps

From request to check — five steps. Diagnostics are free.
Describe the symptom and model — the technician will prepare tools and parts.
The technician comes anywhere in the city and inspects the bike on site.
The technician asks about symptoms, service history, and replaced components to avoid unnecessary disassembly.
The technician identifies the needed part by model and number; you confirm compatibility before work begins.
The technician shows the test ride result and explains what to check in the first few days.
We reply during working hours
Describe the symptom and model — the technician will prepare tools and parts. Ask the technician about scheduling and payment methods.

Warranty question? Call us
+7 (778) 096 59 616 127 reviews of repairs at TECH SERVICE in total
Иван Н.Order No. ZK-2026-208 · 31 August 2026
oursСосед по площадке хвалил, решил проверить. С чем обратился: не едет. Третий месяц — никаких проблем.
Надежда Ц.Order No. ZK-2026-767 · 15 May 2026
oursС левого берега ехать далеко, поэтому искал поближе к дому. Заявку оставил на всякий случай, а зря время тянул. Проблема ровно одна: не едет. Ни копейки больше обещанного. Пришлось ставить: мотор. Ни разу не пожалел.
Вадим Г.Order No. AS-2253 · 11 February 2026
oursХотел вызвать на дом, но в ЖК не пускают без пропуска. Приехал с дачи, а тут — не держит заряд. Все функции проверил — работают
Степан Я.Order No. AST-2604-292 · 23 January 2026
oursС левого берега ехать далеко, поэтому искал поближе к дому. С чем обратился: не едет. Дмитрий Радионов — мастер от бога, если можно так сказать. Полёт нормальный)
Эдуард К.Order No. AS-5020 · 15 September 2025
oursПричина обращения — не держит заряд. Дмитрий Радионов отсоветовал дорогой ремонт, предложил простой. Работает, даже лучше прежнего
Инкар Д.Order No. AST-2510-119 · 28 August 2025
oursҚұрылғы ескі, бірақ жақсы қарайды екен. Мастер бәрін түсіндірді. Бәрі жақсы болды.
Римма Х.Order No. AS-5798 · 11 September 2024
oursС этим и пришёл: не едет. Максим Снегирев показал старую деталь, всё прозрачно. Проверил на всех режимах — держит.
Айдын Щ.Order No. ZK-2023-465 · 20 January 2023
oursҚұрылғы ескі, бірақ жақсы қарайды екен. Ризамын, рахмет. Жұмыс істеп тұр, шағым жоқ.
Екатерина К.Order No. AS-4172 · 4 August 2022
oursБольше всего мешало: не едет. Дмитрий Радионов показал старую деталь, всё прозрачно. Про тех сервис узнал от коллеги из офиса. Третий месяц — никаких проблем.
Константин О.Order No. AS-3925 · 16 December 2021
oursЖиву в Есиле, искал сервис, чтобы не тащится через весь город. Записался на ремонт электровелосипеда. С этим и пришёл: не едет. Дмитрий Радионов — мастер от бога, если можно так сказать. Вышло из строя: аккумулятор. По деньгам вышло ровно, без сюрпризов. Приняли вечером, хотя до закрытия оставалось минут десять. Ни шума, ни запаха, всё штатно.
Олег Х.Order No. AST-2111-565 · 8 December 2021
oursПричина обращения — не держит заряд. Максим Снегирев сам позвонил и сказал, что готово. Пользуюсь и вспоминаю добрым словом
Кайрат Н.Order No. ZK-2021-688 · 11 May 2021
oursМастер бірден қарап шықты. Бөлшек қоймада бар екен, күтпедік. Жұмысты сол күні аяқтады. Ақауын тез анықтады, қажетсіз нәрсе ұсынбады. Қайта жүгінуден тартынбаймын.
Геннадий Ж.Order No. ZK-2021-218 · 2 March 2021
oursСимптом как на ладони: не едет. Дмитрий Радионов разрулил всё быстро. Пользуюсь и вспоминаю добрым словом
Айдын Щ.Order No. AS-7130 · 26 August 2020
oursКүтуге уақытым аз еді, сол күні бітірді. Мастер бәрін түсіндірді. Достарыма айтамын.
Валерия А.Order No. ZK-2020-723 · 7 August 2020
oursПозвонил в четыре места, тут ответили по-человечески. Думал, показалось, ан нет: не едет. Третий месяц — никаких проблем
Людмила Щ.Order No. 2011-3241 · 4 May 2020
oursБыло важно успеть до конца недели, а то морозы обещали. Привёз на диагностику: электровелосипед. Причина обращения — не едет. Обошлось заменой: мотор. Разъёмы на месте, ничего не люфтит.
Пётр Ч.Order No. AS-3557 · 31 October 2019
oursЗаявку оставил через сайт вечером, утром перезвонили. С этим и пришёл: не едет. Внешне не видно, что разбирали.
Мария Р.Order No. AS-9853 · 24 September 2018
oursС левого берега ехать далеко, поэтому искал поближе к дому. С этим и пришёл: не держит заряд. Полёт нормальный.
Денис Л.Order No. AST-1709-181 · 8 September 2017
oursПроблема ровно одна: не держит заряд. Максим Снегирев отсоветовал дорогой ремонт, предложил простой. Внешне не видно, что разбирали.
Юрий М.Order No. 1712-9835 · 23 May 2017
oursМаксим Снегирев пообещал и сделал, без напоминаний. Работает, как будто и не ломалось.
experience14 yearsSenior small appliance technician
experience15 yearsOn-site coffee machine diagnostics technician
experience5 yearsCoffee machine cleaning technician
experience12 yearsCoffee machine diagnostics technician
experience5 yearsPortafilter coffee machine technician
experience12 yearsVacuum cleaner repair technician
experience15 yearsVacuum cleaner repair technician
experience18 yearsWashing machine repair technician
Didn’t find the answer? Message us on WhatsApp.
Ask a questionMost often it's a dead or disconnected battery, the controller's protection kicking in, or corroded contacts. Check the charge level and the battery lock, then inspect the connectors — free diagnostics will pinpoint the exact cause.
It depends on the condition: if individual cells fail, the battery is restored by replacing them; with heavy wear or a damaged protection board, replacement is recommended. The technician decides after testing the battery.
Turn off the power right away and don't switch it back on to avoid shorting the controller. Let the bike dry in a warm place and call a technician: they'll check the contacts, board, and sensors after the moisture.
Usually it's worn Hall sensors in the hub motor, loose contacts, or an overheated controller. Free diagnostics will find the exact cause: the technician will check the phases, sensors, and connections.
Usually the controller is replaced with a new one, since board repair is often unreliable and not worth it. In some cases individual components can be replaced, but that depends on the model and the nature of the fault.
Yes, we provide a 1-year warranty on labor and parts for battery replacement and other work. The warranty applies if you follow the operating rules the technician will explain after the repair.
Tech Service repairs e-bikes in Astana: a technician arrives at your home within 60 minutes or you can drop off your bike at our service center. Diagnostics are free, 1-year warranty on labor and parts, and you can pay with Kaspi QR, Kaspi Red, card, cash, or bank transfer. The technician gives you the price after diagnostics. We work on batteries, controllers, hub motors, and controls.
A black display, loss of power, overheating, and fast discharge are the most common reasons people call us. Let's break down which component is responsible and what checks you can safely do yourself before the technician arrives.
We start diagnostics by measuring the voltage at the battery output: if there's no voltage, we look for the cause in the battery, BMS board, or charging port, not in the motor. A silent display with a charged battery more often points to the controller or a break in the wiring between it and the controls. The BMS board cuts the output when cells are unbalanced, overheated, or protection is triggered — from the outside it looks like a completely dead bike. We check the charging port separately: oxidized contacts give a false impression that the battery is drained. Before the technician arrives, check if the indicator on the battery itself lights up when you press the button — this immediately separates a power issue from a controller issue. It's worth noting the symptom on paper or in a photo: this way the e-bike repair technician in Astana will quickly understand which component to check first.
Loss of power and jerking are most often related to Hall sensors in the hub motor or to voltage sag in the battery cells under load, while overheating is caused by motor overload or oxidized contacts. Hall sensors tell the controller the rotor position, and when they fail, the motor jerks or spins in fits at low speed. Cell sag shows up differently: on flat roads the e-bike runs fine, but on a climb the power drops sharply. Oxidized contacts in the wiring give a similar picture — voltage fluctuates and the controller goes into protection. If the motor only heats up on climbs but runs smoothly on flat roads, don't push it uphill before diagnostics: overheating accelerates winding wear. Also check if the hub motor casing gets hot after ten minutes of riding — a hot hub confirms overload, while a warm one is normal.
The battery is the most expensive component of an e-bike, so it's important to understand which part has failed: the cells, the control board, the connector, or the charger. This determines whether a repair will suffice or a replacement is needed.
We check the control board and cell balance: if individual cells have dropped, we replace them and restore the battery; if the casing or most of the assembly is damaged, we discuss a full replacement. Diagnostics are free: a technician opens the casing, measures the voltage on each group of cells and compares the spread between them. We also test the assembly's electronics separately — it handles cut-off, charge balancing and over-discharge protection, and its failure often looks like 'the battery doesn't hold a charge.' Restoration at Tech Service includes replacing dropped cells and checking the control board. Spot cell replacement makes sense when the other cells show similar values — otherwise the new cell will quickly become unbalanced with the worn ones, and in a month the range will drop again.
| Component | What we check | Sign of failure |
|---|---|---|
| Charging connector | Contact, oxidation, play | Doesn't click into place, gets hot |
| Charger | Output voltage, heating | Doesn't provide the required reading |
| Control board | Cut-off, balancing, protection | Battery doesn't charge, shuts off |
| Cells | Voltage by group, spread | Sharp drop under load |
| Wiring | Integrity, insulation | Contact lost when shaken |
Fast discharge isn't always battery wear: consumption is affected by tire pressure, terrain, cargo weight, worn motor-wheel bearings and cell drop under load. An underinflated tire adds rolling resistance, and the motor draws more current on the same stretch. Worn motor-wheel bearings cause play and extra friction, and riding uphill in a low gear forces the controller to maintain high current longer than usual. An e-bike battery consists of cells and assembly electronics, and a drop in one group under load will show up on a climb or during acceleration, not on a flat road. If the range has dropped sharply rather than gradually, it's more often one problematic cell in the assembly than natural aging of the whole battery.
Traction and control are handled by the controller, motor-wheel, throttle and brake sensors. A fault in one component produces a symptom similar to a breakdown of another, so we check the whole chain, not just a single part.
We test the controller under load and check the throttle signal separately: if the wheel doesn't respond to the throttle but the board outputs voltage to the windings, the cause is in the control, not the electronics. In our practice, confusion between these two components is the most common: the owner replaces the throttle, but the culprit is a blown output stage on the board, or vice versa. Diagnostics follow the chain: signal from the control, controller response, wheel rotation. We capture signal smoothness with an oscilloscope across the entire throttle travel, not at a single rest point, and see how the voltage changes during a smooth turn. A Hall sensor throttle can't be checked by eye — its signal changes smoothly, and a jerk or dip at the start of travel often points to sensor wear, not the board.
Hub motors are usually repairable: we check the winding, Hall sensors, and bearings, and if one element burns out or a bearing wears out, we restore the assembly instead of replacing the whole wheel. We test the winding for inter-turn shorts and opens, position sensors by signal switching when rotated, and bearings by play and hum under load. In geared models, we also check the gears: wear on them causes crunching and jerking at startup that can easily be mistaken for electronics. A burnt winding and a dead position sensor produce a similar symptom—"wheel doesn't spin"—but are fixed differently, so testing each element separately is important. Replacing the wheel as a unit is justified when the core or housing is damaged; otherwise, restoring the assembly preserves the bike's stock electrics.
A code on the screen is a hint from the controller, but the same numbers mean different things on different brands. Let's break down how to read such an error and which component it points to.
Error code decoding depends on the controller firmware and e-bike brand: code E-07 on one manufacturer points to the motor, on another to the throttle or sensor. Manufacturers haven't agreed on common numbering, so a table from one model's manual is useless for another. The display only shows the number, while the logic is built into the firmware of the specific board. Even within one brand, firmware changes from batch to batch, and an experienced technician cross-references the number with the display and control board model, not a generic cheat sheet. The same code on two bikes with seemingly identical specs can lead to different components—the difference lies in the board revision and software version. Note the number and display model before the technician arrives—that pair speeds up decoding more than a single value.
| Error group | What it indicates | What we check |
|---|---|---|
| Open circuit | Connector or chafed wire | Integrity of the harness and contacts |
| Hall sensor | Phase sensor failure in the motor | Signal from three terminals |
| Battery voltage sag | Voltage drop under load | Voltage on the cells |
| Display communication | No data exchange with the control board | Display line and connector |
| Overheating | Thermal protection triggered | Control board and motor temperature |
If a code appears, don't reset it by restarting the device repeatedly and don't take the controller apart — that erases the information that helps a technician find the cause faster. One restart is fine to see whether the error is constant or a one-off. Then check the accessible connectors: a corroded contact or a loose cable can be spotted without tools. Don't pedal uphill with a code on the screen — if a sensor is faulty, the motor may get surge current and heat up more. Take a photo of the screen with the number and note the conditions when it appears — at startup, uphill, or after charging. Also write down what happened before the error appeared: washing, rain, part replacement, a fall. Such details are more useful to a technician than the number itself and cut down the time to find the fault.
We fix some issues right at your place, while others need the service center. Here's what can be done on site, how diagnostics work, and how long you'll wait for a specialist.
At home we fix most issues with controls, wiring, and connectors, and adjust the controller and display — a mobile technician arrives within 60 minutes anywhere in the city. A typical visit covers a frayed or corroded cable from the throttle to the controller, a loose contact in the display connector, or misconfigured PAS and brake sensors. Our technicians test the circuit with a multimeter, check that the terminals are seated, resolder the connector if needed, and reset the parameters on the display. Anywhere in the city, the visit takes under an hour, so people in remote areas don't wait half a day. If the symptoms point to work on battery cells or the hub motor, the mobile technician will confirm it on site and arrange service at the center so you don't have to make two trips.
At the service center we do work that requires disassembling components and testing under load: replacing battery cells, restoring the hub motor, soldering and sealing after water damage. The battery is opened to measure the voltage on each cell group and find the one that drops under load — this defect isn't visible from the outside. The hub motor is disassembled to inspect the winding, bearings, and Hall sensors, then spun under load after reassembly and re-measured. After water exposure, we dry the controller board, clean contacts from oxidation, solder the traces, and seal the housing with sealant. Such work can't be done properly on the go by the entrance — disassembling the battery and testing the motor require a stable workbench and repeated measurements after reassembly.
Warranty and payment terms are what people most often check before contacting us. Here's what the 1-year warranty covers, how we quote the price, and which e-bikes we work with.
The 1-year warranty covers the work we perform and the parts we install: it applies both to replaced battery cells and to servicing the controller or hub motor. If the battery loses capacity again after cell replacement or the controller shows the same error, we handle it as a warranty case, not as a new request — repeat diagnostics and fixing the same fault are not charged again. There is one condition — any tampering with the unit after our work: if the battery was opened elsewhere, the warranty on that unit no longer applies, so keep the seals intact and do not give the unit to third-party technicians. The warranty covers only the work we performed and the parts we installed — it does not cover the condition of other units we did not touch, and we state this clearly before starting work.
The technician quotes the price after free diagnostics, once the cause is found, and you can pay via Kaspi QR, Kaspi Red, bank card, cash, or bank transfer for companies. Diagnostics are free: first the technician identifies the faulty unit — cells, controller, hub motor, or wiring — and only then gives the amount for the specific work and parts. This way you pay for fixing the cause, not for a 'general inspection': the amount includes exactly the operations and parts your unit needs, with no add-ons. You can pay in any convenient way available — cash, card, or transfer, whichever is easier for you. Ask for the price before work begins — that way you compare not an 'average price' but a specific set of work for your unit. Write down the final amount and the list of work: this protects you from extra charges after repair and helps you verify the result at pickup.
| E-bike type | What we check most often | Where we repair |
|---|---|---|
| City | Battery, controller, throttle | On-site and at the service center |
| Mountain | Hub motor, brake sensors, wiring | More often at the service center |
| Folding | Connectors, PAS sensor, cables | On-site and at the service center |
| Cargo | Hub motor, battery, power wiring | More often at the service center |
E-bike symptoms rarely mean 'everything is broken' — each points to a specific unit. Below is a brief summary of what factors determine the outcome of the work and what to look for when choosing a technician.
7brands
We source parts by model and part number. The list includes brands that have dedicated pages on the site.
Tech Service technicians repair other appliances too — with the same 1-year warranty on labour and parts.
Refrigerator Repair in Almatyfrom 3 000 ₸
Washing Machine Repair in Almatyfrom 3 000 ₸
Dishwasher Repair in Almatyfrom 3 500 ₸
Oven Repair in Almatyfrom 3 000 ₸
Cooktop Repair in Almatyfrom 3 500 ₸
Air Conditioner Repair in Almatyfrom 3 500 ₸
Boiler and Water Heater Repair in Almatyfrom 2 500 ₸
Freezer Repair in Almatyfrom 6 000 ₸
Tumble Dryer Repair in Almatyfrom 5 000 ₸
Coffee Machine Repair in Almatyfrom 2 500 ₸
Robot Vacuum Cleaner Repair in Almatyfrom 3 500 ₸
Vacuum Cleaner Repair in Almatyfrom 1 500 ₸
Microwave Oven Repair in Almatyfrom 2 000 ₸
Hair Dryer Repair in Almatyfrom 1 500 ₸
Iron Repair in Almatyfrom 3 000 ₸
Electric Kettle Repair in Almatyfrom 2 500 ₸
Mixer Repair in Almatyfrom 2 500 ₸
Multicooker Repair in Almatyfrom 500 ₸
If your dishwasher won't drain, the most common culprits are a clogged filter or drain hose; less often, it's the pump, impeller…
24 March 2026 · 12 minutes read
A washing machine can hum for many reasons, and the first thing to figure out is when the sound appears.
20 March 2026 · 12 minutes read
The easiest way to remove scale from a kettle is with citric acid: 1–2 tablespoons per liter of water, boil for 5–10 minutes, then drain and rinse.
17 March 2026 · 13 minutes read
If your laptop screen is broken, turn the device off first, don't press on the display, and check the picture through an external monitor.
12 March 2026 · 11 minutes read
Air conditioner errors are codes on the display or flashing indicators that show which component has failed.
5 March 2026 · 12 minutes read
If your washing machine isn't filling with water, the most common culprits are a closed valve, a clogged inlet filter screen on the hose…
20 February 2026 · 13 minutes read












