Оксана Т.Order No. AST-2503-214 · 2 November 2025
oursИскал сервис, где дают гарантию и чек. Раньше обращался в другой сервис, там очередь на две недели. Tech-service оказался единственным, кто взял такую модель.
City
Language
What broke
Sections
Message on WhatsApp+7 (778) 046 88 53Mon–Fri 10:00–19:00, Sat–Sun 11:00–18:00
A technician arrives within 60 minutes anywhere in the city. Diagnostics are free.
Our own technicians4 to 20 years of experience




Repair prices
Below are typical symptoms and likely causes. The technician will confirm the exact cause after a free diagnostic.
burned-out heating element, temperature sensor, or cord
from5 000 ₸
broken cord, thermal fuse
from2 000 ₸
mechanism, contacts
from2 000 ₸
loose mount, worn axle
from5 000 ₸
damaged insulation, plug
from2 000 ₸
heating element, thermostat
from5 000 ₸
worn heating element
from5 000 ₸
coating worn off
from2 500 ₸
The table lists the 'from' price for labor, for common jobs also the 'from' price of the part, plus the time required to complete the job.
1–2 hourstime
from 2,000 ₸cost

BeforeAfter5 steps

From request to acceptance — five steps.
Submit a request, describe the issue and the tool model.
On site, the technician will inspect the body, check the cord and plug, and test the heating.
The technician will agree with you on the scope of work and the time when they can start the repair.
The technician performs the repair within the agreed timeframe and lets you know when it's ready.
Accept the work: ask the technician what was replaced and how to care for the tool.
We reply during working hours
Clear some space near a power outlet, place the tool where the technician can easily reach it, and have the model information handy.

Warranty question? Call us
+7 (778) 046 88 536 127 reviews of repairs at TECH SERVICE in total
Оксана Т.Order No. AST-2503-214 · 2 November 2025
oursИскал сервис, где дают гарантию и чек. Раньше обращался в другой сервис, там очередь на две недели. Tech-service оказался единственным, кто взял такую модель.
Яна Э.Order No. AS-2674 · 12 June 2024
oursСервис выбрал по карте — этот был ближе всего. Заявку оставил через сайт вечером, утром перезвонили. Общение спокойное, без навязывания. Работу закончили раньше срока. Приняли технику в конце дня, не отправили домой. Назвали сумму заранее, в конце она не поменялась. Не пришлось ездить дважды. Цену не подняли, хотя работа оказалась сложнее. Рекомендую, без пафоса.
Елизавета Л.Order No. TSA-70074 · 5 April 2022
oursДолго выбирал, остановился на этом варианте. Было важно успеть до конца недели, а то морозы обещали. Цену не подняли, хотя работа оказалась сложнее. Сделали то, что обещали, и ничего лишнего. Позвонили, когда можно забирать. Работу закончили раньше срока. Могу советовать
Еркежан К.Order No. AS-1149 · 1 January 2022
oursИскал сервис, где дают гарантию и чек. Техника на балансе ТОО, нужен был чек и акт. Сервис оставил нормальное впечатление.
Ульяна Ч.Order No. TSA-64234 · 10 July 2021
oursНужен был срочный ремонт, позвонил утром. Дамир М отсоветовал дорогой ремонт, предложил простой. Обращусь снова, если понадобится.
Юрий М.Order No. TSA-95747 · 29 May 2019
oursПривезли технику из офиса, нужен был акт. Рустем Т принял без вопросов, хотя был без записи. Функционирует, тьфу-тьфу.
Галина Ф.Order No. 29449 · 8 July 2018
oursПозвонил, потому что техника встала и ждать было некогда. Для Астаны — хороший вариант
Юрий М.Order No. AS-5148 · 25 February 2018
oursНужен был срочный ремонт, позвонил утром. Дамир М посмотрел и честно сказал: менять не надо.
Анастасия Т.Order No. AS-7433 · 18 January 2017
oursИскал сервис, где дают гарантию и чек. Мастер посмотрел при мне, объяснил, что случилось. Для Астаны — хороший вариант.
Любовь Ю.Order No. 1607-8915 · 23 October 2016
oursПривезли технику из офиса, нужен был акт. Выбирал между официальным и этим, выбрал этот. В целом доволен.
experience14 yearsSenior small appliance technician
experience15 yearsOn-site coffee machine diagnostics technician
experience5 yearsCoffee machine cleaning technician
experience12 yearsCoffee machine diagnostics technician
experience5 yearsPortafilter coffee machine technician
experience12 yearsVacuum cleaner repair technician
experience15 yearsVacuum cleaner repair technician
experience18 yearsWashing machine repair technician
Didn’t find the answer? Message us on WhatsApp.
Ask a questionYes, we accept premium and professional models for repair, including Dyson, Philips, and BaByliss. The technician will determine what exactly failed — the heating element, circuit board, or sensor — during free diagnostics; it depends on the model.
Yes, this is repairable: most often the heating element, thermal sensor, or internal contacts are to blame. The technician will determine the exact cause during free diagnostics, and the scope of work depends on the model.
This usually happens due to overheating protection, a worn-out thermostat, or a poor connection in the cord and plug. It's best not to keep using them: the fault could lead to a short circuit.
Yes, the clamp mechanism and hinge can be repaired: we restore the mounting and the movement of the plates so they don't come apart. Repairability depends on the model and the condition of the housing.
Stop using the straighteners immediately: a damaged cord is dangerous due to short circuits and electric shock. The technician will check the cord and contacts and replace the power cord if necessary.
Yes, housing repairs and plate replacement are possible, but they depend on the model and the condition of the housing. The technician will assess the damage during free diagnostics and suggest a solution.
Tech Service repairs hair straighteners, flat irons, and stylers in Astana: our technician comes to your home within 60 minutes or the work is done at our service center. Diagnostics are free, we agree on the price after diagnostics, and we provide a 1-year warranty on labor and parts. Our technicians have 4 to 20 years of experience.
Straighteners, flat irons, and stylers fail in different ways, but the principle is the same: first find out what exactly broke, then fix it. Below we list what we accept and which components fail first.
We repair household and professional straighteners, flat irons, and multi-stylers—for home and salon use. We accept curling irons with ceramic, tourmaline, and metal plates, flat irons for hair straightening, stylers with a set of attachments, and devices with ionization. We also service salon equipment that runs for several hours a day: it puts more stress on the heating element and hinge. We provide hair straightener repair in Astana with an on-site technician—he comes to your home, and complex cases are handled at our service center. In my experience, most often people bring in medium-diameter curling irons and flat irons with wide plates. The type of device determines what's inside: stylers with attachments more often have issues with the attachment mechanism, while simple curling irons—with the heating element and cord.
| Symptom | Likely cause | What we do |
|---|---|---|
| Won't turn on | broken cord, board | check power and circuit |
| Not heating | heating element | replace element |
| Doesn't hold temperature | thermostat, sensor | calibrate or replace |
| Sparks, burning smell | cord, control board | disassemble, insulate |
| Broken clamp | hinge, spring | restore mechanism |
| Display error | board, sensor | diagnose electronics |
By the symptom, the technician often already knows where to look during diagnostics. Let's go over the most common complaints about the device and what's behind them.
If the device turns on but doesn't heat up, or heats more on one side, the cause is usually the heating element and the temperature sensor. Inside the working plates there's a coil or ceramic heater, and next to it a thermostat that reads the actual temperature and sends data to the board. When the coil partially burns out, one plate stays cold or heats up noticeably slower than the other. If the sensor fails, the electronics get incorrect readings: heating doesn't start at all, or sometimes the element runs at maximum. At Tech Service, we fix thermostat faults and check the integrity of the heater so the plates reach the set mode in sync. Before blaming the device, it's worth checking whether the temperature setting got knocked off — sometimes the 'breakdown' turns out to be a reset mode.
Devices that won't turn on or turn off by themselves usually point to the control board, buttons, or a break in the cord. The electronics are responsible for supplying power to the heater, reading the display, and overheating protection, so if the traces and contacts are damaged, the device behaves unpredictably: it doesn't respond to the power button, blinks an indicator, or shows an error code. A stuck button sends a false signal, and the device turns off mid-styling. A broken wire in the cord near the base of the housing shows up the same way — power comes and goes. We diagnose the control board and electronics, test the cord and contacts to find the point of failure. Turning off by itself during operation is often a sign of board overheating, so don't keep pushing the device until it cools down.
We repair the clamp mechanism and cord separately from the electronics — these are the most repairable faults in a straightener. The hinge takes constant stress when the plates are pressed together, and over time the axle loosens or the plastic housing cracks, so the clamp stops holding the strand. The cord suffers at the bend where it exits the housing: wires become exposed, sparking and a burning smell appear — it's best to unplug such a model immediately. We restore the hinge and clamp mechanism, replace the damaged section of the cord, and check the insulation so the device doesn't spark during use. The hinge breaks more often on thin flat irons with tight pressure, and the cord — on models that are often folded right after use while still hot.
There are two ways to fix a straightener: a technician comes to you or the work is done at the service center. Let's break down what's done where and what affects the timeline.
A Tech Service technician arrives at your place within 60 minutes anywhere in the city and performs free diagnostics of the straightener on site. The technician comes to your home, so you don't need to haul the device across town or find a window in your schedule. On site, the specialist opens the housing, checks the cord, contacts, buttons, and heating, names the cause, and agrees on the work before starting. At home, it's more convenient to fix things that don't require fully disassembling the housing — the cord, clamp, buttons: these operations are done in front of you and without risk to the plates. For deeper electronics, the technician can take the device to us and handle the complex case at the service center. Before the visit, describe the symptom — it helps the technician understand what they're dealing with in advance.
| Fault | Where we fix it | Why |
|---|---|---|
| Damaged power cord | At your home | Replaced in front of you, without taking the body apart |
| Broken clamp, hinge | At your home | Mechanical work, need access to the mount |
| Stuck buttons | At your home | The top panel is removed |
| Heating element doesn't heat | At the service center | Needs testing under load and soldering |
| Control board failure | At the service center | Electronics diagnostics required |
| Melted body near the plates | At the service center | The whole unit needs replacing |
The time depends on the fault and the part needed, so the technician gives an exact time after free diagnostics. Simple mechanical work — replacing the cord, straightening the clamp, cleaning contacts — usually takes less time than finding an electronics fault: there the specialist goes through the chain from the plug to the board and checks every unit. They also agree on the price after diagnostics, when the cause is known — this avoids surprises at the end. Don't rely on an "average time" from the internet: one model blows a fuse, another has oxidized contacts near the heater, and the difference in work is noticeable. The 1-year warranty on labor and parts applies whether the device was repaired at your home or at our workshop — if the same fault happens again due to our work, the device will be checked again.
Before the repair, it's important to understand what the hair straightener check includes, what the warranty covers and how payment works. We explain each step in order, without fine print or hidden conditions.
Our hair straightener diagnostics is free: the specialist checks the heating, electronics, cord and clamp mechanics and identifies the cause of the fault. First, they measure the resistance of the heating element and see whether the coil reaches operating temperature or breaks along the way. Then they examine the control board for burnt traces and swollen capacitors, and test the cord at the base and at the plug — that's where the wire most often frays. They also inspect the hinge and pressure plates separately: a misaligned clamp is often mistaken for a heating fault, even though the device simply doesn't close evenly. During the check, it's worth showing exactly how the fault appears — at what moment the device turns off or how it heats up — this noticeably speeds up finding the cause. A technician with 4 to 20 years of experience can narrow down the suspect units just from the device's behavior before even opening the body.
We provide a 1-year warranty on hair straightener repair — both on labor and on parts. If a replaced heating element or a repaired control board fails again due to our work, the specialist will redo the work at no extra cost to you. The warranty covers the unit we worked on: when we replaced the cord, it applies to the cord and its soldering point, not to the hinge that wasn't repaired. The warranty applies to the unit we repaired. The warranty is tied to the specific work performed, so if the fault happens again, it's important for the technician to know which unit was repaired last time. For this reason, if the fault happens again, it's important to know which unit was repaired last time.
The technician gives you the price after a free diagnostic check, and you can pay via Kaspi QR, Kaspi Red, card, cash or bank transfer. Until they've opened the casing and checked the heating, the board, and the cord, it's impossible to give an honest quote — the difference between replacing a cord and restoring the electronics is too big. So first the check, then the approval: you hear which part has failed and how it will be repaired, and only after you agree does the technician start work. You can pay via Kaspi QR, Kaspi Red, bank card, cash, or bank transfer for companies. Approving before work begins is convenient because you know the scope and the final amount in advance, instead of facing extra charges later. A practical tip: at this stage, ask exactly which operations are included in the agreed price, so the list matches what the technician said out loud. We work as a direct contractor: the technician comes themselves, so no middleman commission is built into the agreed price.
Expensive and salon-grade flat irons are more complex than household ones, and they need a different approach to servicing. Here's what owners of such devices should know before contacting a technician.
We work with Dyson, Philips, and BaByliss devices — both household and more complex models from these brands. In expensive devices, the control board manages heating based on sensor readings, and the heating element and casing are put together more tightly than in a simple flat iron. Because of that, disassembly requires care: the plastic and fasteners on such models are thinner, and the wrong force leaves marks. We take on both mechanical failures — hinge, clamp, cord — and electronic ones: board faults, temperature sensor failure, uneven heating. Expensive models have more complex electronics and tighter layouts, so diagnostics take more attention than with a simple flat iron. Owners of such devices should check in advance that the technician has disassembled that specific model.
We also service professional flat irons for salons — they work under heavy load and wear out faster than household ones. In a salon, the device is turned on dozens of times per shift, and the heating element and thermostat go through more use than a home flat iron does in years. Most often we see temperature drift from the set value, uneven heating along the plates, and hinge wear from constant opening. The technician checks heating at several settings, inspects the contacts and control board, and assesses the thermostat's condition. For salon flat irons, it's more important to restore stable heating than to fix them at any cost — the styling results for clients depend on it. If the device is used daily, it makes sense to check the heating before obvious faults appear.
| Parameter | Household | Professional and expensive |
|---|---|---|
| Layout | simple, loose fit | tight, thin fasteners |
| Electronics | basic board | control board with sensors |
| Heating | single element | element and thermostat |
| Casing disassembly | comes off quickly | requires care |
| Typical wear | cord, clamp | hinge, thermostat, board |
When the device stops heating or turning on, the question arises: take it to a service center or just get a new one. Here's what the decision depends on and how to make it without unnecessary costs.
Repair usually makes sense when the problem is localized — a cord, a clamp, buttons, a heating element — and the plates and plastic are intact. A frayed cord at the base, a loose hinge, a sticky power button, or a failed heating element are isolated faults where the rest of the device is fine. Replacing one component restores the device's operating temperature and heating stability, while the surface coating and electronics remain as before. At Tech Service, we start with free diagnostics: it shows whether there is really just one cause or if the visible symptom hides several defects. If after checking there is one fixable cause, repair restores the device's working parameters without buying a new model — and the money you set aside for a replacement stays with you. This approach is especially beneficial for expensive and professional models, where replacement costs noticeably more than a targeted repair.
Replacement is smarter when the plates or plastic are damaged and repair won't restore the device's working properties. Chipped or peeling coating on the working surfaces means the device will snag hair and heat unevenly even after replacing the heater — the working contact itself is already compromised. Cracked plastic at the hinge or melted geometry at the heating block also can't be restored to original condition. In such cases, repair makes no sense: it won't fix the reason the device damages hair. The decision should be made after diagnostics, not by appearance — sometimes a seemingly hopeless flat iron turns out to have one fixable fault, and it's too early to throw it away. The technician explains the cause of the breakdown based on the symptom and honestly says what repair will and won't achieve.
Here are the key points to keep in mind when your flat iron breaks, so you can decide on repair or replacement without unnecessary doubt.
14brands
We can help with tools from popular brands that have dedicated pages on our site.
Tech Service technicians repair other appliances too — with the same 1-year warranty on labour and parts.
Refrigerator Repair in Almatyfrom 3 000 ₸
Washing Machine Repair in Almatyfrom 3 000 ₸
Dishwasher Repair in Almatyfrom 3 500 ₸
Oven Repair in Almatyfrom 3 000 ₸
Cooktop Repair in Almatyfrom 3 500 ₸
Air Conditioner Repair in Almatyfrom 3 500 ₸
Boiler and Water Heater Repair in Almatyfrom 2 500 ₸
Freezer Repair in Almatyfrom 6 000 ₸
Tumble Dryer Repair in Almatyfrom 5 000 ₸
Coffee Machine Repair in Almatyfrom 2 500 ₸
Robot Vacuum Cleaner Repair in Almatyfrom 3 500 ₸
Vacuum Cleaner Repair in Almatyfrom 1 500 ₸
Microwave Oven Repair in Almatyfrom 2 000 ₸
Hair Dryer Repair in Almatyfrom 1 500 ₸
Iron Repair in Almatyfrom 3 000 ₸
Electric Kettle Repair in Almatyfrom 2 500 ₸
Mixer Repair in Almatyfrom 2 500 ₸
Multicooker Repair in Almatyfrom 500 ₸
If your dishwasher won't drain, the most common culprits are a clogged filter or drain hose; less often, it's the pump, impeller…
24 March 2026 · 12 minutes read
A washing machine can hum for many reasons, and the first thing to figure out is when the sound appears.
20 March 2026 · 12 minutes read
The easiest way to remove scale from a kettle is with citric acid: 1–2 tablespoons per liter of water, boil for 5–10 minutes, then drain and rinse.
17 March 2026 · 13 minutes read
If your laptop screen is broken, turn the device off first, don't press on the display, and check the picture through an external monitor.
12 March 2026 · 11 minutes read
Air conditioner errors are codes on the display or flashing indicators that show which component has failed.
5 March 2026 · 12 minutes read
If your washing machine isn't filling with water, the most common culprits are a closed valve, a clogged inlet filter screen on the hose…
20 February 2026 · 13 minutes read












