Original
Manufacturer's pump
- Selection
- by part number or machine model
- Fit
- matches factory
- Connector
- matches original
- Check
- number verification before installation
City
Language
What broke
Sections
Message on WhatsApp+7 (778) 746 00 26Mon–Fri 10:00–19:00, Sat–Sun 11:00–18:00
Washing machine drain pump replacement with diagnostics. The technician will determine whether a new pump is needed or the filter just needs cleaning.
Our own technicians4 to 20 years of experience




1 yearwarranty on labor and parts
60 minutestechnician visit across the city
2000 tgpump replacement
The pump doesn't move water if the impeller is jammed or the filter is clogged. Leaks during draining come from the pump connections, hoses, and drain hose. The impeller is checked for free rotation, and water is drained through the emergency hose. The price is quoted after free diagnostics.
01
Step 1as per procedure
The technician identifies the faulty unit and scope of work before starting replacement, so you understand what is being replaced and why.
02
Step 2as per procedure
First, filter and hose clogs are ruled out: debris is the most common cause of drain failure.
03
Step 3as per procedure
They check if the impeller rotates freely: jamming indicates a foreign object or wear.
04
Step 4as per procedure
If the unit is faulty, a new pump is installed and the connections and hoses are checked for leaks.
05
Step 5as per procedure
After reassembly, they run a drain cycle and make sure it works without leaks.
5
Five typical symptoms point to the drain unit. But similar signs can be caused by a clogged filter, a kinked hose, or a foreign object in the impeller, so the pump verdict is made after inspection.
Cycle stops at drain
The program interrupts at the drain stage, and a drain error code appears on the display.
Leak during draining
Water leaks out through the pump connections, hoses, or a damaged drain hose.
Humming during draining
Unusual noise during draining indicates debris in the impeller or wear of the unit.
No water fill after drain
After draining, the program locks and doesn't start a new fill; the pump doesn't switch to the next stage.
Drain error only on spin
At high spin speeds, a drain code appears, although water drains without errors at other stages.
Where to find the pump in the machine: the unit is behind the bottom panel, next to the emergency hose.
Describe the symptomsThe pump is selected by part number or machine model. For Bosch, the E-Nr number is on the label inside the door.
Original
or
Analog
The table lists the 'from' price for labor, for common jobs also the 'from' price of the part, plus the time required to complete the job.
1 visittime
from 7 000 ₸cost

BeforeAfterWe reply during working hours
Submit a request for pump replacement and confirm a convenient visit time and payment method with the technician. Technicians have 4 to 20 years of experience; you can pay via Kaspi QR, Kaspi Red, card, cash or bank transfer.

Warranty question? Call us
+7 (778) 746 00 266 127 reviews of repairs at TECH SERVICE in total
Зоя М.Order No. AST-2611-737 · 16 September 2026
oursЗаявку оставил через сайт вечером, утром перезвонили. Жалоба одна: вибрация. Третий месяц — никаких проблем.
Семён Ш.Order No. TSA-54682 · 19 June 2026
oursС чем обратился: шумит при отжиме. Дильмурат С посмотрел и честно сказал: менять не надо. Вернули — проверил, всё ок.
Валерий Д.Order No. AS-9920 · 2 June 2026
oursОсновная жалоба — шумит при отжиме. Астанинский Tech-service — нормальный вариант. Вернули — проверил, всё ок
Альбина Ю.Order No. AS-5393 · 13 April 2026
oursПозвонил в четыре места, тут ответили по-человечески. Проблема ровно одна: не отжимает. Рустем Т — мастер от бога, если можно так сказать. Ни разу не пожалел.
Ярослав С.Order No. AST-2508-434 · 8 December 2025
oursЖалоба одна: не сушит. Ораз показал старую деталь, всё прозрачно. Пользуюсь и вспоминаю добрым словом.
Зоя М.Order No. AS-7170 · 19 July 2025
oursПервое, что заметил: не отжимает. Рустем Т сам позвонил и сказал, что готово. Крутит ровно, без рывков.
Сымбат Х.Order No. 88858 · 4 November 2024
oursҚұрылғыны әкелдім, бірден қабылдады. Нәтижесіне ризамын. Қайта жүгінуден тартынбаймын.
Валентина Р.Order No. TSA-91786 · 11 August 2024
oursОфис на Кабанбай батыра, технику туда и повёз. Скепсис был, признаю. Жалоба одна: не сушит. Стоит, роботает, радует)
Зоя М.Order No. AS-4933 · 25 August 2020
oursДима отсоветовал дорогой ремонт, предложил простой. Третий месяц — никаких проблем
Борис В.Order No. AS-1453 · 10 June 2020
oursВыбирал между официальным и этим, выбрал этот. Если честно, руки опустились, когда оно щёлкнуло и затихло. Первое, что заметил: не включается. Приехал без записи, но свободный мастер нашёлся. Вскрытие показало: насос. Работает, даже лучше прежнего.
experience10 yearsSenior washing machine technician
experience16 yearsWashing machine installation technician
experience12 yearsWashing machine repair technician
experience10 yearsWashing machine board repair technician
experience11 yearsDishwasher repair technician
Didn’t find the answer? Message us on WhatsApp.
Ask a questionIf the machine stops during the drain cycle with water still in the drum and the pump motor makes no sound, the pump is most likely not working. If you hear a hum but the water stays put, the culprit is usually a clog or a jammed impeller. A technician can tell for sure after checking.
Unplug the machine and drain the water through the emergency hose behind the service flap at the bottom front, placing a towel underneath. After that, you need a technician: they will check the filter, hoses, and the pump itself. In Astana, diagnostics are free and a technician arrives within 60 minutes.
Most often, debris blocks the impeller: a coin, lint, or a bra underwire. Less often, a clogged filter or hose is to blame, preventing water from reaching the pump. The technician checks whether the impeller spins freely and clears the drain path.
First, open the filter at the bottom front behind the service flap: if water drains after cleaning, the pump is fine. If the pump hums with no water or stays silent and the filter is clean, the problem is in the pump itself or the hose. A technician will give a final diagnosis after checking.
You can if you have the tools and experience: on some brands the pump is accessible from below, but access depends on the model. Without skill, it's easy to damage the mounts or hoses, so it's better to let a technician handle the replacement. They will match the part by part number or model code.
Small items and lint slip past the filter and get stuck in the impeller, causing it to jam. To avoid this, check pockets before washing and clean the drain filter regularly. A clogged filter puts extra load on the pump.

Author: Vladimir V.,Senior washing machine technician
Published
Updated
Tech Service replaces washing machine drain pumps in Astana at your home or in our service center: our own technician arrives within 60 minutes anywhere in the city, diagnostics are free, and there's a 1-year warranty on labor and parts. The technician gives you the price after diagnostics, and you can pay via Kaspi QR, Kaspi Red, bank card, cash, or bank transfer for companies.
The 'won't drain' symptom has three main suspects: the filter, the hose, and the pump. Let's look at how to tell them apart before the technician arrives and when a repair is really needed.
We check whether the impeller spins freely: if it's jammed by debris or won't turn by hand, the unit is replaced, and a multimeter won't show a jammed part. Humming during drain usually means the blades are stuck on a coin or lint, not that the motor is burned out. A continuity test will show a broken coil, but not a jam — so in our practice, checking rotation is more important than any measurements. A clogged mesh gives a similar picture: water stands, the machine stops mid-cycle. The difference is that after cleaning, draining resumes immediately, while a jammed unit keeps humming and doesn't pump water out. If the impeller won't turn by hand, the part is replaced entirely, not worked loose.
The cause of pump failures is debris (coins, lint, small objects) and a clogged filter, while scale has nothing to do with unit wear. Small objects slip past the mesh and get stuck in the impeller, lint winds around the shaft and gradually stops rotation. Scale builds up on the heating element and sensors, it doesn't reach the pump — so don't link it to a drain failure. Check and rinse the mesh regularly, and empty pockets before washing: a coin in the drum is a direct path to a jam. If you don't replace a humming unit and keep washing, the jammed impeller stops turning completely, and the machine stops mid-cycle with water in the tub. Until then, the pump usually hums on every drain — that sound is the signal to call a technician.
The code on the display narrows the search, but the meaning depends on the model. Below are the designations that most often indicate difficult water drainage, and how the technician verifies them.
| Brand or series | Designation | What it means |
|---|---|---|
| Some d02 models | E18 or F18 | Drain problem |
| Samsung | 5E (SE, E2) | Drain problem |
| Electrolux | E20 | Drain problem |
| Indesit and Hotpoint | F05 | Drain problem |
F-codes on older Bosch and Siemens series On older Bosch and Siemens series (Maxx, Classixx, Logixx, Avantixx), F18 is drain, F17 is water intake, F16 is door, F19 is heating, F21 is motor, F23 is water in the base, and on models without a display the designation is shown by indicators. You can't blame the pump based on one code: F21 points to the motor, not water drainage, so we cross-check the signal with the table for your machine before talking about replacement. Current Serie 2/4/6/8 series use a different set, and the technician opens the table for the specific E-Nr from the rating plate behind the door. We first check whether the impeller spins freely, and only then name the work. This order saves time and avoids extra parts in the order.
If the machine has stopped with water in the drum and the door is locked, you need to act carefully. Let's go over the safe procedure and what not to do.
If liquid doesn't drain after installing a new pump, we check the drain hose, pipes, and pressure switch — a clog or kink in the line gives the same symptom as a faulty pump. The drain pump doesn't work during fill, so it's tested separately during the spin cycle: the technician listens to see if the pump turns on and checks whether the impeller spins freely. A clogged pipe between the drum and pump or a pinched corrugated hose behind the sink prevents water from draining even with a new part. At Tech Service, diagnostics are free and done before repair: replacing the pump blindly means paying for a part that doesn't solve the problem. In our experience, the cause is in the hose or filter as often as in the pump itself, so we first check the entire drain path and then identify the faulty unit.
Pump replacement is work from below, but access differs by brand. Here's how we select the part and what we check along the way.
We select the pump by part number or model code — for Bosch, it's the E-Nr on the plate in the door — and replace the pump entirely rather than repairing the old impeller. We verify the number against the manufacturer's catalog: different series of the same brand may have different mounting points and connectors, so the unit isn't chosen "by size." Along the way, the technician checks whether the impeller of the removed part spins freely and inspects the drain hose and filter — a clogged filter is often the cause of failures. A multimeter won't show a jammed pump, but impeller rotation is immediately visible. We install the new unit in place of the old one with the same connector to avoid rewiring. Selecting by model code rather than "by size" matters because it determines whether the part fits without modifications and whether the warranty on the part remains valid. The cost of washing machine pump replacement is discussed after the part is selected.
| Work | Access | Complexity |
|---|---|---|
| Pump replacement | From below | Basic |
| Heating element replacement (Bosch/Siemens) | From the front | Medium |
| Bearing replacement | Removal of tank and drum | Longest |
The final question is who to trust with the repair and what happens if something goes wrong. What matters here is the warranty, visit speed, and who exactly will come to your machine.
We give a 1-year warranty on labor and parts, and the technician who arrives is a Tech Service specialist, not a middleman from an aggregator. Over years of working with home appliances, we've seen the main weakness of contractor schemes: one person replaces the part, another promises the warranty, and if the problem comes back, the owner is stuck between them. With us, the person doing the work and the warranty obligations are the same: if the pump we installed leaks or stops draining water, you go back to the same technician instead of looking for a new one. Our specialists have 7 to 20 years of experience, so they can tell a worn-out pump from a clogged filter at a glance and won't replace a part if the real cause is elsewhere. Having the warranty on both the part and the work in one document is convenient because if the problem returns, you don't have to prove whose part failed.
A specialist arrives within 60 minutes anywhere in the city, diagnostics are free, and the cost of washing machine pump repair is discussed after that — we accept Kaspi QR, Kaspi Red, card, cash or bank transfer. You can book by phone or on the website: just give the brand, model, and the error code shown on the display, so the technician can bring the right pump for your machine in advance. We cover all of Astana, including the new residential areas on the left bank and the older neighborhoods on the right, so we confirm your district when you book. Washing machine pump replacement in Astana with a direct contractor starts with a free inspection. Free diagnostics before replacement lets you find out whether you need a new pump at all and avoid paying for a job that doesn't solve the problem.
The drain system of a washing machine is simpler than it seems: most failures come down to the filter, the hose, or the pump itself. Below is a quick guide to help you avoid paying for unnecessary repairs and assess the situation correctly before the technician arrives.
If you ask, the technician will check other parts during the same visit.
Refrigerator Repair in Almatyfrom 3 000 ₸
Dishwasher Repair in Almatyfrom 3 500 ₸
Oven Repair in Almatyfrom 3 000 ₸
Cooktop Repair in Almatyfrom 3 500 ₸
Air Conditioner Repair in Almatyfrom 3 500 ₸
Boiler and Water Heater Repair in Almatyfrom 2 500 ₸
Freezer Repair in Almatyfrom 6 000 ₸
Tumble Dryer Repair in Almatyfrom 5 000 ₸
A washing machine can hum for many reasons, and the first thing to figure out is when the sound appears.
20 March 2026 · 12 minutes read
If your washing machine isn't filling with water, the most common culprits are a closed valve, a clogged inlet filter screen on the hose…
20 February 2026 · 13 minutes read
Washing machine error codes are self-diagnostic codes that point to a specific component: drain, water fill, heating, motor, or door lock.
29 January 2026 · 13 minutes read
If your washing machine won't spin, it's usually an unbalanced load, a clogged drain filter or hose, and less often the pump, belt…
19 January 2026 · 12 minutes read
If your washing machine isn't heating water, the heating element or temperature sensor is usually to blame, less often the control board or wiring.
25 December 2025 · 12 minutes read
If your washing machine won't turn on, first check the outlet, extension cord, and the circuit breaker in your panel, then the plug and power cord.
24 November 2025 · 13 minutes read