Жамиля В.Order No. 2606-6051 · 23 April 2026
oursЖұмыстан кейін баруға болатын жер іздедім. Алдымен интернеттен қарадым, кейін осында келдім.
City
Language
What broke
Sections
Message on WhatsApp+7 (778) 046 88 53Mon–Fri 10:00–19:00, Sat–Sun 11:00–18:00
We come on call and find the cause of the breakdown. Diagnostics are free.
Our own technicians4 to 20 years of experience




Repair prices
Below are typical symptoms and likely causes. The technician will pinpoint the exact component after diagnostics.
ignition, flame sensor, gas valve
from6 000 ₸
ignition, draft, circulation
from7 500 ₸
tank, air, leak
from5 500 ₸
seals, pipes, pump
from10 500 ₸
air, bearing, scale
from5 500 ₸
nozzles, gas pressure, valve
from7 000 ₸
temperature sensor, board, thermostat
from6 000 ₸
valve, heat exchanger
from7 000 ₸
Labor prices are shown excluding parts; parts are paid separately upon agreement.
1 visittime
from 6 000 ₸cost

BeforeAfter5 steps

Five steps from request to checking the work.
Submit a request, specify the boiler model, and describe what's happening.
When confirming the request, specify the boiler model, error code, and access to the boiler.
Prepare access to the boiler, your ID, and the error code on the display; the inspection is quick.
We discuss the scope of work and parts, and start after your approval.
Check ignition, pressure, and absence of leaks together with the technician.
We reply during working hours
Submit a request and prepare access to the boiler, the model's passport, and the error code on the display — this will speed up the inspection.

Warranty question? Call us
+7 (778) 046 88 536 127 reviews of repairs at TECH SERVICE in total
Жамиля В.Order No. 2606-6051 · 23 April 2026
oursЖұмыстан кейін баруға болатын жер іздедім. Алдымен интернеттен қарадым, кейін осында келдім.
Софья Ц.Order No. AS-5952 · 11 September 2025
oursХотел вызвать на дом, но в ЖК не пускают без пропуска. Думал, показалось, ан нет: не зажигается. Посмотрели, назвали срок, уложились. Обошлось заменой: теплообменник. В другом месте просили на треть больше. Проверил на всех режимах — держит.
Алим В.Order No. TSA-30020 · 27 July 2025
oursКеңседегі құрылғы, чек пен акт керек еді. Мастер бірден қарап шықты. Қайта жүгінуден тартынбаймын.
Екатерина К.Order No. TSA-22987 · 27 July 2025
oursСмотрел, чтобы был свой склад запчастей, а не под заказ. С чем обратился: ошибка. Полёт нормальный!!
Денис Л.Order No. AST-2512-892 · 14 June 2025
oursЖиву в Есиле, искал сервис, чтобы не тащиться через весь город. Жалоба одна: ошибка. Крутит ровно, без рывков.
Аркадий Я.Order No. TSA-61574 · 12 May 2025
oursС левого берега ехать далеко, поэтому искал поближе к дому. Проблема ровно одна: течёт. Выбирал по карте, Tech-service был ближе всех. Гудит ровно, не перегревается.
Регина Ф.Order No. 86727 · 7 April 2025
oursРаньше обращался в другой сервис, там очередь на две недели. Привёз на диагностику: газовая колонка. Причина обращения — течёт. Дамир М разрулил всё быстро. В техсервис попал случайно, возвращаться буду. Тихо, ровно, без сюрпризов
Ульяна Ч.Order No. 2403-8041 · 29 November 2024
oursОсновная жалоба — не греет воду. Дамир М провозился, но сделал. После ремонта — как новое.
Пётр Ч.Order No. TSA-22227 · 12 September 2024
oursПричина обращения — не греет. Дамир М объяснял без умных слов, за это спасибо. Функционирует, тьфу-тьфу
Борис В.Order No. ZK-2024-450 · 8 September 2024
oursПервое, что заметил: не зажигается. Никита М посмотрел и честно сказал: менять не надо. Шум ушёл, работает мягко.
Вера Э.Order No. AS-9288 · 19 June 2024
oursС левого берега ехать далеко, поэтому искал поближе к дому. Нужен был ремонт газовой колонки. Симптом как на ладони: не зажигается. Никита М не пропал после ремонта, помог с настройкой. Стоит, работает, радует
Нурсултан Т.Order No. AS-6008 · 21 January 2024
oursЖұмыстан кейін баруға болатын жер іздедім. Мастер бірден қарап шықты. Нәтижесіне ризамын
Леонид П.Order No. AST-2301-407 · 25 November 2023
oursВыбирал между официальным и этим, выбрал этот. С чем обратился: ошибка. Даже сосед заметил, что громче не стало.
Инна Н.Order No. AST-2303-816 · 19 November 2023
oursРаньше обращался в другой сервис, там очередь на две недели. Симптом как на ладони: течёт. Нагрев в норме, посторонних звуков нет!!
Константин О.Order No. AS-7884 · 2 April 2023
oursЗнакомый мастер раньше здесь работал, дал номер. С этим и пришёл: течёт. Крутит ровно, без рывков.
Галина Ф.Order No. 2304-8352 · 22 February 2023
oursС чем обратился: течёт. Никита М разрулил всё быстро. Даже сосед заметил, что громче не стало.
Леонид П.Order No. AST-2301-380 · 29 January 2023
oursСосед по площадке хвалил, решил проверить. Ни с того ни с сего — течёт. Никита М разрулил всё быстро. По факту меняли: мембрана. Оплату взяли после ремонта, а не вперёд. Заплатил бы и больше, если честно. Работает, как будто и не ломалось
Борис В.Order No. AS-2805 · 23 November 2022
oursЗнакомый мастер раньше здесь работал, дал номер. Первое, что заметил: не зажигается. Внешне не видно, что разбирали
Анастасия Т.Order No. ZK-2022-511 · 5 November 2022
oursОсновная жалоба — течёт. Дамир М показал старую деталь, всё прозрачно. Проверил на всех режимах — держит.
Екатерина К.Order No. AST-2204-178 · 22 October 2022
oursЗнакомый мастер раньше здесь работал, дал номер. Позвонил насчёт газовой колонки. Первое, что заметил: течёт. Не пришлось стоять в очереди, хотя народу было. 8 500, и гарантия в комплекте. По факту меняли: теплообменик. Работает, даже лучше прежнего
experience11 yearsDishwasher repair technician
experience10 yearsSenior washing machine technician
experience11 yearsStove and oven repair technician
experience11 yearsFreezer repair technician
experience16 yearsWashing machine installation technician
experience8 yearsDishwasher technician
experience12 yearsWashing machine repair technician
experience10 yearsWashing machine board repair technician
Didn’t find the answer? Message us on WhatsApp.
Ask a questionTo a specialized service where a technician comes to your home and runs the diagnostics on site. At Tech Service, we cover Astana, and there's a one-year warranty on the work performed and parts.
Gas equipment repair should only be trusted to a qualified service technician. Tampering with the gas line and controls yourself is life-threatening and prohibited.
Contact a direct service that repairs on site and doesn't pass requests to middlemen. Before the technician arrives, shut off the gas and don't take the casing apart yourself.
The boiler's controls detect an abnormal condition and block ignition until parameters are restored. Sometimes a reset per the instructions helps, but if the error repeats, you need a technician.
On site, technicians usually replace sensors, the pump, expansion tank, and clean the burner and heat exchanger. Complex repairs of the circuit board or gas valve depend on the model and may require service.
Yes, our technicians work with Baxi, Vaillant, Navien, Ferroli, Ariston, and other brands. Based on the model, they identify the cause and choose whether to repair on site or at the service center.
Tech Service repairs gas boilers in Astana at your home or in our service center: our technician arrives within 60 minutes anywhere in the city, diagnostics are free, and you get a 1-year warranty on labor and parts. The technician gives you the price after inspection, and you can pay any way you like.
Most calls start with a symptom, not a part name: the boiler is silent, won't heat water, or flashes an error. Let's break down what's behind it and where to start looking for the cause.
Most often the unit won't start because there's no ignition, the pressure in the circuit has dropped, or the safety automation has tripped, and our technician checks these components first. Over the summer, the ignition electrodes get covered in oxide and stop producing a spark, the burner gets clogged with dust, and the pressure sensor detects a drop in the heating system and blocks the start. The automation behaves differently: some models show a code, others just won't go into mode. After a long idle period, it's also worth checking whether the gas valve is open and whether there's pressure in the heating system — these are the most common reasons a boiler stays silent after the summer. Before calling a technician, look at the pressure gauge: if the needle is below the operating zone, that explains the lockout without taking the casing apart.
If the boiler hums and turns on but the water or radiators stay cold, the cause is usually a heat exchanger clogged with scale, a stuck hydraulic valve, or settings that have gone off. With hard water, the heat exchanger builds up deposits faster than anything else, the temperature sensors read the wall heating instead of the flow, and the burner shuts off too early. In dual-circuit models, the hydraulic valves stick after idle periods and don't switch the flow between heating and hot water. Settings get reset after power surges when the board returns to factory parameters. Don't rush to replace the unit — flushing the heat exchanger often restores heating without replacing the part, and with hard water it's worth planning as a regular procedure rather than a one-time fix. During the free diagnostics, our technician tells a clogged heat exchanger from a stuck valve by the temperature difference between inlet and outlet.
Repeated shutdowns are usually linked to an unstable gas supply, voltage surges, or a faulty feedback sensor that sends a false signal to the automation. The control board fails after power surges, feedback sensors distort readings and trigger an emergency stop, and the boiler interprets a drop in gas pressure in the line as a flame failure. The error repeats at the same interval — that's how the component is identified. If the error appears after a gas or power outage, the problem may not be in the boiler itself but in the external supply — mention this to the technician when you call so they bring the right instruments. Note how many minutes after start the code appears: the interval narrows down the causes better than the error number itself.
The code on the display is a hint from the automation, not a death sentence for the boiler. Here's how to read it, why the interpretation depends on the model, and which components the signal most often points to.
An error code points to a specific component or sensor, but the same combination can mean different things across manufacturers, so always check the interpretation against your model's manual. The automation doesn't record the whole failure, just a parameter deviation: circuit pressure, coolant temperature, flame presence, or draft. The same symbol on a wall-mounted and a floor-standing boiler often refers to different circuits, and on models with flame modulation, the burner status code is added to the signal. On alphanumeric displays, the first position usually indicates the group, the second — the specific fault. Write down the code and the boiler model before calling a technician — that pair makes it easier to guess the cause in advance and bring the right part.
After a power surge or gas outage, a boiler often goes into error mode due to a control board failure or a safety lockout, which our technician clears after checking the components. Electronics respond to a grid voltage spike by tripping the protection, and when the gas supply stops, the automation closes the valve and blocks ignition — this prevents fuel from accumulating in the combustion chamber. On boilers with ionization flame control, the electrode calibration is sometimes lost after a power surge, and the burner won't start even with a normal gas supply. In our practice, such calls after thunderstorms and rolling blackouts are one of the most common reasons for a service visit. Don't reset the error repeatedly — repeated ignition attempts without fixing the cause put stress on the automation and the burner.
| Component group | What the signal indicates | What the technician checks |
|---|---|---|
| Pressure and temperature sensors | pressure drop, overheating | readings and sensor integrity |
| Burner and ignition | no flame, flame failure | electrodes, gas supply |
| Flue | weak draft, exhaust removal | patency and tightness |
| Control board | electronics failure | power and automation circuits |
| Heat exchanger | overheating, scale | flow rate and circuit temperature |
Gas equipment doesn't forgive DIY attempts. We separate the alarming symptoms that require an urgent call from situations where you can safely wait for a specialist.
You need to call a technician urgently if you smell gas, the burner goes out with repeated flame failures, or there's a coolant leak — in these cases our specialist arrives within 60 minutes anywhere in the city. The burner may go out due to fuel supply problems, a clogged nozzle, or a faulty flame sensor, and leaks most often occur at heat exchanger joints and pump seals. If you smell a leak, first close the valve on the supply line, ventilate the room, don't turn on electrical appliances or light any fire — only then call. If water is leaking, shut off both the water and the fuel, place a container under the drip, and move anything that could get wet away from the boiler. If the unit goes into error again after a reset, don't restart it — note the code and model. An urgent call during a leak is about safety, not convenience: there should be no sources of sparks in the room until the specialist arrives.
Gas equipment requires certification and knowledge of safety standards, so tampering with the burner, controls, or gas components risks leaks and carbon monoxide poisoning. A mistake in burner assembly or an incorrectly set ignition electrode gap causes incomplete combustion, and a clogged or displaced flue returns carbon monoxide into the room—colorless and odorless. Boiler controls are designed for factory settings, and makeshift adjustment of the gas valve disrupts flame and draft safety controls. An incorrectly assembled unit can work almost normally for years, and the failure will show up at the worst possible moment, so testing is left to an experienced technician. Our engineer comes to your home, finds the cause, and fixes it to code—tampering with gas components without certification is dangerous and voids the service warranty.
We fix most breakdowns right at the customer's place, but some work requires disassembling components at our facility. Here's how we decide and what a technician visit includes.
At your home, our technician replaces sensors, ignition electrodes, water valves, and adjusts the controls, while complex repairs of the control board or heat exchanger may require the shop. On-site we handle everything that doesn't involve bench disassembly: we check draft, clean the burner, adjust gas pressure, and set boiler operating modes. It's easier to solder the control board on a bench under a magnifier, and to flush the heat exchanger on a special rig—doing that in an apartment is inconvenient and risky for surrounding items. The decision to take the boiler to the shop is made after diagnostics and with your approval, so there are no surprise equipment transports. In my view, it's more honest to say right away that the unit needs to go to the shop than to take it apart in the kitchen.
The technician arrives within 60 minutes anywhere in the city, performs free diagnostics, checks equipment safety, and agrees on the work and parts before starting. First, he inspects the flue and ventilation, checks inlet gas pressure, tests ignition, and reads the error code from the display if there is one. Then he disassembles the failing unit and shows you the fault—so the cause is visible not just to the technician. He quotes the price after the inspection, once the scope is clear. Free diagnostics means inspection and finding the cause, not a guarantee that no work will be needed. In our practice, half of the calls end with replacing one inexpensive part, and the client is surprised the problem was so minor.
| Work | Component | Where it's done |
|---|---|---|
| Replacing sensors and electrodes | sensors, ignition | at the customer's place |
| Adjusting controls | control board | at the customer's place |
| Flushing the heat exchanger | heat exchanger | at the customer's place or in the shop |
| Repairing the control board | electronics | in the shop |
| Cleaning the combustion chamber and burner | burner, chamber | at the customer's place |
| Replacing the air blower | fan | at the customer's place or in the shop |
| Servicing the expansion tank | tank, diaphragm | in the shop |
Before booking, it's important to understand what you're paying for and what commitments you get after gas boiler service. Here's how warranty, free diagnostics, and payment for work are handled.
We give a 1-year warranty on labor and parts, so if the issue comes back after service, the technician will fix it under warranty. The coverage applies to the replaced component and the quality of its installation: the burner, control board, sensor, circulation pump, three-way valve, ignition electrode. Technicians with 4 to 20 years of experience record exactly which component was replaced and why, which ties the warranty to a specific operation rather than the entire unit. If a breakdown occurs in a different part, it is treated as a new case and diagnosed separately. Keep the information about the replaced part — it makes it easier to confirm that the issue is related to the work performed and not to outside interference. When you receive the service, check that the work description names the specific component — a vague wording like 'boiler repair' makes it harder to confirm that the breakdown is linked to our operation.
Our diagnostics are free: a specialist finds the cause of the breakdown and explains which component needs attention, and you decide whether to order the work. The check starts with questions about the symptoms, then the technician checks the pressure in the circuit, ignition, draft, the condition of the electrodes and the board, reads the error code from the display, and checks the gas line connections for leaks. As a result, you get not a general 'the boiler is faulty' but a specific component and cause: a clogged filter, worn ignition electrode, stuck valve, board failure after a power surge, or a clogged heat exchanger. An honest check sometimes ends with the advice not to repair the component but to replace it — that is cheaper in the long run than repeated call-outs. We arrive in the city within 60 minutes, so diagnostics don't stretch into days of waiting.
The technician gives you the price after the free diagnostics, when the cause and scope of work are clear, and you can pay in any convenient way. The price includes labor and parts if a part needs to be replaced; the selection is agreed with you before work begins so you know what you are paying for. You can pay via Kaspi QR, Kaspi Red, bank card, cash, or bank transfer for companies — cash, card, transfer. We are a direct contractor: our own technician comes to your home, not an intermediary, so there is no dispatch markup or extra links between you and the specialist. Agreeing on the work and parts before starting protects you from unexpected extra charges — you know in advance what you are paying for instead of sorting out the numbers afterward. Ask the technician what exactly is included in the quoted amount before they start work — it makes it easier to compare offers and avoid overpaying for unnecessary operations.
A boiler breaks down less often if it is looked after, and it is better to choose a technician before an emergency. Here we cover preventive maintenance, brands, and the difference between a contractor and an intermediary.
Servicing gas boilers — cleaning the burner and flushing the heat exchanger — extends the life of components and reduces the risk of a sudden breakdown during the heating season. We perform this maintenance as a separate job: remove the burner, clean soot from the nozzles, flush scale from the heat exchanger, check the pressure in the circuit and the condition of the ignition electrodes. Scale and deposits build up unnoticed and show up as higher gas consumption and weak heating — maintenance is cheaper than restoring a clogged heat exchanger. In our practice, boilers that are cleaned once a year are less likely to show overheating and ignition errors: a clogged burner gives an uneven flame, and a layer of scale in the heat exchanger makes the pump work at its limit. If the boiler has gone through a season without service, start with diagnostics — it is free and will show the condition of the components before they fail.
Our technicians service Baxi, Vaillant, Navien, Ferroli, and Ariston boilers, including atmospheric, turbocharged, and condensing models. An atmospheric boiler draws air from the room through an open combustion chamber, a turbocharged one takes air from outside via a coaxial flue, and a condensing boiler also uses the heat from water vapor. The boiler type affects the set of components — condensing models have a condensing unit and a condensate drain siphon, while turbocharged models rely on the draft of the coaxial flue and the fan operation. Wall-mounted models with a closed chamber more often throw a draft error, while floor-standing atmospheric models show ignition and gas pressure errors. Before calling a technician, check the model and combustion chamber type — we use them to select the right parts in advance and bring them with us.
Here are the key things to keep in mind when your boiler stops working properly — from the first symptom to deciding on repair.
20brands
We work with boilers from popular brands. When you request service, tell us the boiler model — this helps the technician prepare for the visit.
Tech Service technicians repair other appliances too — with the same 1-year warranty on labour and parts.
Refrigerator Repair in Almatyfrom 3 000 ₸
Washing Machine Repair in Almatyfrom 3 000 ₸
Dishwasher Repair in Almatyfrom 3 500 ₸
Oven Repair in Almatyfrom 3 000 ₸
Cooktop Repair in Almatyfrom 3 500 ₸
Air Conditioner Repair in Almatyfrom 3 500 ₸
Boiler and Water Heater Repair in Almatyfrom 2 500 ₸
Freezer Repair in Almatyfrom 6 000 ₸
Tumble Dryer Repair in Almatyfrom 5 000 ₸
Coffee Machine Repair in Almatyfrom 2 500 ₸
Robot Vacuum Cleaner Repair in Almatyfrom 3 500 ₸
Vacuum Cleaner Repair in Almatyfrom 1 500 ₸
Microwave Oven Repair in Almatyfrom 2 000 ₸
Hair Dryer Repair in Almatyfrom 1 500 ₸
Iron Repair in Almatyfrom 3 000 ₸
Electric Kettle Repair in Almatyfrom 2 500 ₸
Mixer Repair in Almatyfrom 2 500 ₸
Multicooker Repair in Almatyfrom 500 ₸












