Оксана Т.Order No. AS-2340 · 28 October 2026
oursПроблема ровно одна: не закрывается. Дильмурат С посмотрел и честно сказал: менять не надо. Дома включил, всё на месте.
City
Language
What broke
Sections
Message on WhatsApp+7 (778) 021 11 78Mon–Fri 10:00–19:00, Sat–Sun 11:00–18:00
A technician arrives within 60 minutes anywhere in the city. Diagnostics are free.
Our own technicians4 to 20 years of experience




Repair prices
Below are typical symptoms and likely causes. The technician will pinpoint the exact cause after diagnostics.
refrigerant leak, compressor failure
from10 000 ₸
worn seal, sensor failure
from6 000 ₸
clogged drain, crack in the housing
from11 000 ₸
thermostat failure, refrigerant leak
from10 000 ₸
worn compressor, vibrating pipes
from10 000 ₸
control board failure, broken circuit
from20 000 ₸
start relay, compressor winding
from7 500 ₸
wear, dirt, deformed profile
from6 000 ₸
Choose a problem group to see the relevant price list items.
1 visittime
from 11 500 ₸cost

BeforeAfter5 steps

From request to post-repair check.
Describe the symptom and the freezer model so the technician brings the right tools.
Clear space around the freezer, pull it away from the wall, and provide access to the back panel.
What you get after the inspection: a list of checked components and possible solutions, without prices.
Discuss which operations the technician will do on site and which require taking the freezer to the workshop.
Check the list of completed work in the report and ask the technician to explain any disputed points in writing.
We reply during working hours
Describe the symptom and the freezer model: the technician will bring the right tools and parts. Ask about the work and payment procedure.

Warranty question? Call us
+7 (778) 021 11 786 127 reviews of repairs at TECH SERVICE in total
Оксана Т.Order No. AS-2340 · 28 October 2026
oursПроблема ровно одна: не закрывается. Дильмурат С посмотрел и честно сказал: менять не надо. Дома включил, всё на месте.
Анастасия Т.Order No. AST-2606-449 · 17 October 2026
oursПричина обращения — не включается. Дильмурат С разобрался в редкой модели. Третий месяц — никаких проблем.
Регина Ф.Order No. ZK-2026-275 · 15 October 2026
oursС чем обратился: не морозит. Дильмурат С отсоветовал дорогой ремонт, предложил простой. Крутит ровно, без рывков.
Лариса О.Order No. TSA-10965 · 27 September 2026
oursИскал, кто работает в субботу, у нас с женой график сложный. Позвонил жене, говорит: наледь. Тихо, ровно, без сюрпризов
Галина Ф.Order No. AST-2602-964 · 15 April 2026
oursПервое, что заметил: не морозит. Дильмурат С провозился, но сделал. Ни разу не пожалел.
Лариса О.Order No. ZK-2026-133 · 3 January 2026
oursСимптом как на ладони: не закрываеться. Никита М всё сделал при мне, за пятнадцать минут. После ремонта — как новое!!
Леонид П.Order No. 38130 · 10 November 2025
oursТехника на балансе ТОО, нужен был чек и акт. С чем обратился: наледь. Полёт нормальный.
Ерлан Б.Order No. TSA-15129 · 23 August 2025
oursӘйелім «таста» деді, мен көрсетуді жөн көрдім. Қосымша жұмыс қажет болды, бірақ бағаны көтермеді. Бөлшек қоймада бар екен, күтпедік. Бағаны алдын ала айтты, соңында өзгермеді. Кепілдік берді, бұл маңызды. Жұмысты сол күні аяқтады. Ақауын тез анықтады, қажетсіз нәрсе ұсынбады. Мастер бәрін түсіндірді. Түскі үзіліске қарамастан қабылдады. Келесіде де осында келемін.
Римма Х.Order No. 98867 · 19 June 2025
oursБольше всего мешало: намерзает. Дильмурат С объяснял без умных слов, за это спасибо. Третий месяц — никаких проблем.
Степан Я.Order No. AS-8854 · 1 April 2025
oursРаньше обращался в другой сервис, там очередь на две недели. Приехал с дачи, а тут — не морозит. Выдали номер заказа и сказали, как отслеживать. Сказали 12 000 по телефону, столько и вышло. Замена: компрессор. Советую. Нагрев в норме, постороних звуков нет
Геннадий Ж.Order No. AST-2403-729 · 5 September 2024
oursТехника на балансе ТОО, нужен был чек и акт. С чем обратился: не включаеться. Внешне не видно, что разбирали
Вадим Г.Order No. AS-2011 · 4 September 2024
oursВчера работало, сегодня уже не морозит. Дильмурат С подобрал аналог дешевле, не навязывал оригинал. Итог — 12 500 тенге, ничего сверху. На ресепшене оформили за пару минут, выдали квитанцию. Замена: термостат. Обращусь ещё. Работает, даже лучше прежнего.
Екатерина К.Order No. AS-6332 · 24 November 2023
oursВыбирал между официальным и этим, выбрал этот. Сначала списал на мороз, но нет: намерзает. Никита М отсоветовал дорогой ремонт, предложил простой. Внутри оказалось: компрессор. Итог — 21 000 тенге, ничего сверху. Ответили в мессенджере, потом созвонились. Дома включил, всё на месте.
Жанель У.Order No. 83949 · 16 September 2023
oursКүтуге уақытым аз еді, сол күні бітірді. Келесіде де осында келемін. Келесіде де осында келемін.
Екатерина К.Order No. TSA-26689 · 27 June 2023
oursНикита М провозился, но сделал. Замена: компрессор. Стоит, работает, радует.
Степан Я.Order No. 2307-1329 · 21 April 2023
oursС левого берега ехать далеко, поэтому искал поближе к дому. Я обычно такое не пишу, но тут пусть будет. С этим и пришёл: не включается. Дильмурат С объяснял без умных слов, за это спасибо. Сначала думал, что нужен паспорт, но обошлось. Пришлось ставить: компрессор. Заплатил бы и больше, если честно. Обращусь ещё. Работает, как будто и не ломалось
Инна Н.Order No. AST-2206-463 · 17 June 2022
oursПервое, что заметил: намерзает. Никита М не пропал после ремонта, помог с настройкой. Крутит ровно, без рывков.
Зоя М.Order No. ZK-2022-359 · 11 May 2022
oursСмотрел, чтобы был свой склад запчастей, а не под заказ. Первое, что заметил: не закрывается. Полёт нормальный.
Леонид П.Order No. ZK-2022-355 · 16 March 2022
oursРаньше обращался в другой сервис, там очередь на две недели. Симптом как на ладони: не включается. Тихо, ровно, без сюрпризов.
Яна Э.Order No. ZK-2021-761 · 13 May 2021
oursНикита М разобрался в редкой модели. Сейчас пашет без нареканий.
experience11 yearsFreezer repair technician
experience11 yearsDishwasher repair technician
experience10 yearsSenior washing machine technician
experience11 yearsStove and oven repair technician
experience16 yearsWashing machine installation technician
Didn’t find the answer? Message us on WhatsApp.
Ask a questionMost often it's a refrigerant leak, a faulty compressor, or incorrect thermostat settings. During free diagnostics, the technician will check the refrigerant pressure and how the components are working; it depends on the model.
Yes, the technician will replace the seal or adjust a misaligned door on-site. This eliminates ice buildup and cold loss; the exact method depends on the freezer model.
When the compressor fails, there's usually no characteristic hum, while a faulty relay or thermostat produces clicks without starting. Only free diagnostics can accurately distinguish the components; it's not something you can determine by eye.
Yes, it's a risk of short circuit and damage to the flooring, so it's best to unplug the freezer before the technician arrives. The cause is often a clogged drain or a worn seal; it depends on the model.
If the code doesn't disappear after defrosting and turning it back on, call a technician: they will decode the error for your model and check the sensors and electronics. A one-time code appearance can be a glitch; it depends on the model.
Many freezer breakdowns can be fixed by a technician on-site, while complex cases involving the compressor or refrigerant leaks sometimes require a service center. What exactly is needed will become clear after free diagnostics; it depends on the model.

Author: Ozat K.,Freezer repair technician
Published
Updated
Tech Service repairs freezers in Astana at your home or at our service center: a technician arrives within 60 minutes anywhere in the city, diagnostics are free, and you get a 1-year warranty on labor and parts. Our technicians have 4 to 20 years of experience and fix refrigerant leaks, replace compressors, relays, thermostats, and control boards.
Your freezer is acting up, and the symptoms can already point to the faulty component. Let's look at the three most common scenarios and what the technician checks in each case.
If the light is on but there's no cold, the freezer is getting power, so the problem is in the cooling circuit or the component that controls it: most often a refrigerant leak, a faulty compressor, or a thermostat. Refrigerant circulates in a closed loop, and when it loses pressure, the evaporator stops cooling. The motor may hum, but the temperature inside stays at room level. A thermostat with burnt contacts won't signal the compressor to start, and the freezer just sits there silently. At-home freezer repair starts with checking the cooling circuit and electronics: our technician runs free diagnostics and only then names the cause. A running compressor sounds almost the same as a dead one, so don't turn the thermostat to max before the technician arrives: it won't speed up freezing but will make diagnostics harder.
A repeated click with a pause is a typical sign of a start relay: it tries to start the compressor but can't, and the cycle repeats. The relay sends the start pulse and protects the motor winding; when its contacts burn or lose springiness, the compressor jerks, clicks, and goes silent for a few minutes. The same symptom can come from a seized compressor or a blown fuse in the circuit, and only meter readings can tell the difference. We replace the compressor, start relay, and thermostat based on diagnostics, not on sound. If the freezer does start after a few clicks and runs, it's better to replace the relay before it fails completely, as that's cheaper than replacing the compressor.
Constant humming without shutting off is usually because the freezer isn't reaching temperature: the compressor runs nonstop trying to make up for lost cold or a faulty sensor. A temperature sensor with skewed readings won't send the stop command, and the motor hums for hours. A door seal with gaps lets warm air in, and the freezer keeps trying to catch up with the lost cold. A clogged condenser at the back can also be the cause: the fins can't dissipate heat, and the cycle drags on. Check if the freezer is pushed against the wall and if the condenser at the back is clogged. Poor heat dissipation also makes the compressor run longer, and that's not a breakdown but an operating condition. If you've restored the clearance and cleaned the fins, and the humming and nonstop running persist, the cause is in the components: sensor, thermostat, or cooling circuit. Then you can't do without diagnostics: you can't identify the faulty part by sound, and replacing parts at random only makes the repair more expensive.
Ice and water aren't always a breakdown, but they're not something to ignore either. Let's figure out when it's just defrosting and when it's a sign of a faulty component.
A thick layer of ice on the walls is either a misuse issue (door left open too long, warm food) or a fault: a worn seal, a faulty heater, or a sensor in the No Frost system. The seal lets warm air in, which condenses on the walls and freezes again after each defrost. In drip-system compartments, frost buildup is more often caused by a door that isn't closed tightly and by food placed inside while still hot. If the gasket is intact but ice builds up again a few days after a full defrost, the problem lies in the defrost components: the heater isn't warming the evaporator, or the sensor isn't triggering the cycle. In No Frost compartments, frost almost always points to a failure in this cycle rather than the compressor — so don't assume you're in for an expensive repair right away.
An internal leak is most often caused by a clogged drain hole, while water on the floor points to a damaged seal or a crack in the drip tray; in both cases the cause can be fixed. The drain carries condensate to the tray, and crumbs, bits of packaging, or ice block the channel — water pools at the bottom of the compartment and leaks out. A damaged gasket lets condensate run down the body, and a cracked tray lets meltwater through onto the floor. Our technician handles the work either at your home or in our service center: they check the drain, the door alignment, and the integrity of the tray. Before calling a technician, wipe up and dry the floor — the location of the puddle (under the door, at the back, inside) will help them pinpoint the component even before the visit.
| Symptom | Likely cause | What we check |
|---|---|---|
| Not cooling, light is on | Refrigerant leak, compressor, thermostat | Cooling circuit, compressor |
| Clicks but won't start | Start relay, compressor | Relay, compressor windings |
| Ice buildup, frost | Heater, sensor, seal | Defrost cycle, door gasket |
| Leaking inside | Clogged drain | Drain hole |
| Leaking outside | Seal, drip tray | Gasket, tray |
| Hums and won't shut off | Temperature sensor, cold leak | Sensors, condenser |
While the specialist is on the way, a few simple steps will help you save your food and make diagnosis easier. Here's what to do and what to avoid.
You don't need to defrost the freezer before the technician arrives — in fact, the pattern of ice and how the compressor runs helps us pinpoint the cause faster. The layer of ice on the evaporator shows how the refrigerant is distributed, and where the frost builds up hints at where heat removal is disrupted or the capillary tube is clogged. A full defrost wipes out that picture: you arrive to an empty freezer and have to recreate the conditions, wasting time on re-freezing. Defrosting is only justified when the appliance hasn't been defrosted for a long time and the ice is clearly excessive — then it blocks access to components and seals. Before the visit, we provide free diagnostics, so any remaining frost only helps: it shows whether the compressor was running before the breakdown and how deeply the evaporator froze, meaning the technician arrives with a ready hypothesis.
Tell us the freezer model, type (freestanding, built-in, chest), the symptom, and when it appeared — that's enough for the specialist to bring the right parts. Clarify how the appliance behaves: is the compressor humming, is the light on inside, are there clicks when trying to start, is water leaking outside. If there's an error code on the display, write it down — the code often identifies the faulty component before the visit, so the technician arrives with the needed part. It also helps to recall if there were power surges or if the freezer was moved recently. With this description, we agree on the work and parts before service begins, so you know in advance what will be done. Our technician reaches customers anywhere in the city within 60 minutes.
Most freezer breakdowns are fixed on-site, but some jobs require a service center. Here's what can be done at home and when the freezer still needs to be transported.
At home, we fix most malfunctions: replace the start relay, thermostat, door seal, control board, fan, and defrost heater. The technician arrives within 60 minutes anywhere in the city, provides free diagnostics, and immediately names the cause — the relay clicks, the thermostat doesn't signal start, the seal lets heat in. We check the control board by testing power circuits and sensors, the fan by blade rotation and evaporator frosting, the defrost heater by resistance. Freezer repair at home in Astana also covers typical cases where a part is replaced without transporting the appliance. On-site service saves time and preserves food: the freezer isn't fully defrosted, and the technician arrives with the right parts. In my view, for an Astana resident this is a decisive argument — hauling a half-empty freezer across town is more hassle than having a specialist come to you.
You take the freezer to a service center when a new compressor needs to be installed with circuit brazing or when complex work on a refrigerant leak is required — such operations can't be done on-site. Brazing requires vacuuming the system and charging refrigerant, which needs a stationary station, not a kitchen. We look for leaks with nitrogen pressure testing: without it, installing a compressor is pointless — the refrigerant will escape through the same crack within a week. We try to service built-in freezers without dismantling the kitchen — if the component is accessible, the work is done on-site. Moreover, removing a built-in appliance from its niche is a separate task: fasteners are often hidden behind the facade, and it's best not to open the cabinet unnecessarily. So the technician first assesses access to the compressor compartment, and only then decides whether transportation is needed.
| Work | At home | At service center |
|---|---|---|
| Relay, thermostat replacement | Yes | — |
| Seal, board replacement | Yes | — |
| Fan, defrost heater replacement | Yes | — |
| Compressor replacement | — | Yes |
| Refrigerant leak repair | — | Yes |
| Built-in freezer | Mostly yes | If component is inaccessible |
A code on the display is not a verdict but a hint from the electronics. Let's break down what's behind the symbols, when to call a specialist, and how troubleshooting differs between electronic and mechanical models.
An error code points to a component that has failed or is not working properly: most often it's the temperature sensor, the control board, or the defrost system. Each brand has its own table of symbols, so the same set of letters and numbers means different faults across manufacturers. The temperature sensor detects a deviation from the set mode and sends a signal to the board, which then displays the code. The defrost system triggers an error when the timer or the evaporator heater fails to activate. A code doesn't always mean a breakdown—sometimes it's the electronics reacting to a voltage spike or improper defrosting, and after a restart it may not recur. Write down the combination of symbols before resetting: it will help the technician quickly determine which circuit to check.
If the code reappears after a restart or is accompanied by a loss of cooling, diagnostics are needed—the code itself won't go away. We provide free diagnostics before repair, checking the cooling circuit and electronics so we don't replace a sensor when the board is at fault. Our technician arrives at your home within 60 minutes anywhere in the city, and there's a 1-year warranty on labor and parts. Don't reset the error repeatedly hoping it will "fix itself": a recurring code indicates a persistent fault that's best resolved before you lose cooling entirely. A freezer with a failed sensor keeps running under strain and gradually thaws your food, so delaying the call isn't worth it.
In units with electronic controls, diagnostics start with the board and sensors, while in mechanical ones—with the thermostat and relay, so the approach to finding the cause differs. Electronics poll multiple sensors and display a specific code, whereas mechanical systems react to the knob position and contact activation. In a mechanical unit, the thermostat opens the circuit based on temperature, and if it fails, the compressor either won't start or runs nonstop. Electronics more often provide precise codes, while mechanical systems give only indirect signs, so in mechanical units the technician relies more on the owner's description of symptoms. Recall how the appliance behaved before the fault appeared: does the relay click, do the lights dim when it starts—these details narrow the search even before opening it up.
Your choice of service provider determines how much the repair will cost and how long the freezer will last. Here's what to look for to avoid overpaying for unnecessary parts.
A direct provider sends their own specialist and takes responsibility for the result, while an aggregator is an intermediary who passes the request to a contractor, and quality depends on the specific contractor. Our service operates as a direct provider: the person with the tools arrives on request, inspects the freezer on site, and fixes the issue themselves. A good freezer repair technician doesn't shift responsibility to a dispatcher and is accountable for the outcome of each visit. With an aggregator scheme, a dispatcher stands between you and the person holding the tools—and when another visit is needed, you get a different person again. With a direct provider, it's easier to get a warranty and a follow-up visit for the same issue—responsibility isn't diluted between the intermediary and the specialist. From our experience, with an intermediary scheme it's harder to prove that a fault is related to previous work, since one contractor handled the request and another showed up.
We provide a 1-year warranty on labor and parts — if the same issue returns, the technician comes back under warranty. In practice, the same symptom almost always means a related component wasn't checked during the first visit: the start relay was replaced but the cause was in the compressor winding, or the drain was cleared but the defrost fault wasn't fixed. That's why we note in the work description which component was replaced and which was checked — on a new request, the technician opens the previous record and follows the familiar chain instead of starting diagnostics from scratch. Keep this description: it makes it easier to match a returning symptom with the previous repair and get help faster.
Here's the key information to help you decide when your freezer breaks down: from reading the symptom to checking the warranty.
29brands
Choose your brand to see the page describing the work on your appliance.
Tech Service technicians repair other appliances too — with the same 1-year warranty on labour and parts.
Refrigerator Repair in Almatyfrom 3 000 ₸
Washing Machine Repair in Almatyfrom 3 000 ₸
Dishwasher Repair in Almatyfrom 3 500 ₸
Oven Repair in Almatyfrom 3 000 ₸
Cooktop Repair in Almatyfrom 3 500 ₸
Air Conditioner Repair in Almatyfrom 3 500 ₸
Boiler and Water Heater Repair in Almatyfrom 2 500 ₸
Freezer Repair in Almatyfrom 6 000 ₸
Tumble Dryer Repair in Almatyfrom 5 000 ₸
Coffee Machine Repair in Almatyfrom 2 500 ₸
Robot Vacuum Cleaner Repair in Almatyfrom 3 500 ₸
Vacuum Cleaner Repair in Almatyfrom 1 500 ₸
Microwave Oven Repair in Almatyfrom 2 000 ₸
Hair Dryer Repair in Almatyfrom 1 500 ₸
Iron Repair in Almatyfrom 3 000 ₸
Electric Kettle Repair in Almatyfrom 2 500 ₸
Mixer Repair in Almatyfrom 2 500 ₸
Multicooker Repair in Almatyfrom 500 ₸
If your refrigerator stops working, first check the outlet, the power cord, and the thermostat setting, and after defrosting let it stand for a while.
4 February 2026 · 12 minutes read
If your refrigerator isn't cooling but the light is on, the cause is usually one of the components in the cooling circuit: the compressor, thermostat…
10 December 2025 · 13 minutes read
If your dishwasher won't drain, the most common culprits are a clogged filter or drain hose; less often, it's the pump, impeller…
24 March 2026 · 12 minutes read
A washing machine can hum for many reasons, and the first thing to figure out is when the sound appears.
20 March 2026 · 12 minutes read
If your washing machine isn't filling with water, the most common culprits are a closed valve, a clogged inlet filter screen on the hose…
20 February 2026 · 13 minutes read
If your microwave isn't heating but the light and turntable still work, the problem is usually one of the high-voltage components — the magnetron, diode…
15 February 2026 · 12 minutes read












