experience9 yearsRuslan Ts.
Washing machine and refrigerator repair technician
City
Language
What broke
Sections
Message on WhatsApp+7 (778) 021 13 16Mon–Fri 10:00–19:00, Sat–Sun 11:00–18:00
Free diagnostics, a technician arrives within 60 minutes anywhere in the city. 1-year warranty on labor and parts.
Our own technicians4 to 20 years of experience




Repair prices
The symptoms customers most often report. The exact cause is determined by the technician after free diagnostics.
magnetron, transformer, or diode
from6 500 ₸
mica or coating contamination
from3 000 ₸
fuse or door switch
from2 500 ₸
fan or turntable motor
from3 500 ₸
latch, hinges, or switches
from4 000 ₸
the code points to a specific component
from6 000 ₸
turntable motor or coupling
from3 500 ₸
bulb or socket contact
from2 000 ₸
The table lists the 'from' price for labor and the time required; the technician confirms the final amount before any repair begins.
1 visittime
from 4 000 ₸cost

BeforeAfter5 steps

From request to performance check — five steps.
Describe the symptom and the oven model so the technician brings the right tools.
Have the oven model ready, describe the symptom, and provide access to the power outlet.
The technician checks the outlet, cord, and fuse before disassembling the oven.
Confirm a convenient visit time and details with the technician by phone before the visit.
The technician cleans up after the repair and leaves the old part if the owner wants it.
The home appliance repair department in Almaty has 8 technicians with 8 to 12 years of experience.

The department has 8 specializations — they are listed on the technicians' cards.
experience9 yearsWashing machine and refrigerator repair technician
experience12 yearsGeneral household appliance repair technician
experience10 yearsField technician for washing machine and refrigerator repair
experience8 yearsExpert washing machine repair technician
experience8 yearsField refrigerator repair technician
experience8 yearsSenior washing machine repair technician
experience11 yearsDishwasher repair technician
experience9 yearsWashing machine repair technician
We reply during working hours
Leave a request — a technician will arrive within 60 minutes anywhere in the city and identify the cause. Technicians have 4 to 20 years of experience, and you can pay via Kaspi QR, Kaspi Red, card, cash or bank transfer.

Warranty question? Call us
+7 (778) 021 13 167 898 reviews of repairs at TECH SERVICE in total
Ержан А.Order No. 2025-6043 · 18 November 2025
oursХотел сначала вызвать мастера на дом, потом передумал. Основная жалоба — не греет. Tech-service оказался ближе всех, за это и выбрал. Работает даже тише, чем до поломки.
Бекзат Т.Order No. ZK-2025/306 · 17 September 2025
oursИскал мастерскую поближе к дому, чтобы не мотаться с техникой через полгорода. Я человек терпеливый, но тут уже думал всё. С чем пришёл: искрит. Дамир М взялся за то, от чего другие отказались. Заодно поменяли: трансформатор. Проверил дома — всё на месте, ничего не забыли.
Арман К.Order No. TS-5806 · 9 November 2024
oursДруг посоветовал, у него похожая история была. Починили и дали гарантию на месяц.
Владимир Н.Order No. 65903 · 21 June 2020
oursДо этого обращался в другой сервис, там только развели руками. Настроение было испорчено конкретно. Симптом был очевидный: не крутится тарелка. Радик Т всё объяснил и не пытался впарить лишнее. В списке работ — двигатель. Запчасть была в наличии, доплачивать не пришлось. Мастер посмотрел, сказал, что возьмётся, и взялся. Работает как раньше, придирок нет.
Айгерим Б.Order No. TS-2010-912 · 28 January 2020
oursХотел сначала вызвать мастера на дом, потом передумал. Симптом был очевидный: не греет. Отдельно спасибо мастеру — Дамир М, терпения ему хватило. Проверили при мне, показали, что всё держит.
Дамир И.Order No. 250505 · 16 October 2019
oursСмотрел, у кого есть запчасти на такую модель. Повод для визита: не крутится тарелка. Вернули в тот же день, всё функционирует.
Руслан Д.Order No. TS-1826 · 17 September 2019
oursПробовал найти мастера в своём районе, но все были заняты. Основная жалоба — искрит. В тех сервис привёл знакомый, у него тут чинили ноут. Ребёнок уже проверил на прочность, держится.
Полина В.Order No. 61503 · 21 November 2018
oursИскал мастерскую поближе к дому, чтобы не мотаться с техникой через полгорода. Повод для визита: не крутится тарелка. Второй месяц — полёт нормальный.
Индира П.Order No. 2018-7365 · 16 April 2018
oursОсновная жалоба — не греет. Отдельно скажу про мастера: Радик Т — спокойный, без лишней суеты. Работает как раньше, придирок нет!!
Сергей Р.Order No. TS-1602-689 · 15 April 2016
oursҚұрылғы ескі болғандықтан, бөлшек табыла ма деп қорықтым. Асығыс болмасам да, бір күнде бітіретінін айтты. Асыққан адамға ыңғайлы.
Didn’t find the answer? Message us on WhatsApp.
Ask a questionUsually the turntable motor or a slipped drive shaft under the glass is to blame. Check that the roller rest is sitting level; the technician will pinpoint the exact cause during diagnostics — it depends on the model.
If the cavity is clean, the cause is often a burned-through mica plate or damaged door seal. Radiation passes through them, so these parts need to be replaced — it's dangerous to ignore.
No, it's dangerous: the high-voltage section holds a lethal charge, and a mistake in reassembly risks radiation. Magnetron and capacitor replacement should be left to a technician who tests the oven after repair.
The sign is a completely dead oven: no display, no light, even though the outlet works. But a faulty mains fuse behaves the same way, so only a technician's check gives a definite answer.
Yes, we repair Hansa microwaves in Almaty even after the factory warranty, and a technician comes to your home within 60 minutes. We provide a 1-year warranty on labor and parts.
Most often the cause is worn membrane contacts or a faulty control board. A technician can check and replace the unit after diagnostics — repair is possible at your home.
Tech Service repairs Hansa microwaves in Almaty: our technician arrives at your home within 60 minutes or accepts the appliance at the service center. Diagnostics are free, we agree on the price after diagnostics, and we provide a 1-year warranty on labor and parts. Technicians have 4 to 20 years of experience.
It won't heat, but the light and fan work — the most common symptom in Hansa microwaves. Let's look at which parts are responsible and what the technician checks first.
On our visits, it's usually not the emitter itself but its surrounding components — the high-voltage fuse, diode, or capacitor — and free diagnostics confirms this. The magnetron generates microwaves for heating, but without proper power it won't start: the fuse is the first to take the surge when a breakdown occurs, while the diode and capacitor form the required voltage. The cooling fan keeps running, so the oven hums and lights up, but the chamber stays cold. Replacing just one fuse without checking the diode and capacitor brings the fault back after a few uses. The emitter itself is replaced less often than the symptoms suggest: the technician first checks the power supply and high-voltage circuit, because "not heating" with the fan running looks the same for three different faults.
The high-voltage transformer powers the magnetron, and when it fails, the oven hums louder than usual but the chamber stays cold. The windings operate under high voltage, and a breakdown here changes the sound: the hum becomes denser, sometimes with a metallic tone, and there's no heating at all. The diode and capacitor in this circuit are checked together with the transformer — they're connected in series, and a fault in one component loads the others. During measurements, the technician compares the emitter's power supply with the rated value, not just the appearance of the parts: a burnt winding isn't always visible to the eye. Humming without heating is a reason not to "push" the mode but to stop trying: operating with a broken high-voltage section loads the other components and can finish off a working magnetron.
| Symptom | Likely component | What the technician checks |
|---|---|---|
| Not heating, fan works | Fuse, diode, capacitor | Power supply and high-voltage circuit |
| Hums louder, chamber cold | High-voltage transformer | Windings and magnetron power supply |
| Sparking at chamber wall | Waveguide, mica plate | Contamination and plate burn-through |
| Sparking at door | Hinges, seal, latches | Door fit and interlock |
| Won't turn on, no display | Fuse, latches | Power circuit and interlock |
Sparking inside the chamber isn't always a breakdown. Sometimes it's due to contamination, sometimes to door components. We'll show how the technician tells one from the other.
The mica plate covers the waveguide from splashes and grease, and when it burns through or gets wet, microwaves start sparking at the chamber wall. The plate sits at the waveguide's output — the channel through which the magnetron's energy enters — and is the first to catch grease from soup and splashes from heating without a lid. Over time, the mica darkens, gets brown spots, and burnt tracks appear along the edges — these are the breakdown points. The plate is replaced as a consumable, but first the technician checks whether contamination has gone deeper into the waveguide: if only the visible part is wiped, sparking will return. The channel itself also needs cleaning if there's heavy carbon buildup — care is important here to avoid damaging the inner walls.
In our experience, sparking at the door is most often caused by a poor seal: worn hinges or a worn gasket let radiation escape, and it arcs along the edge of the cavity. The door gasket — the flexible seal around the perimeter — hardens, cracks, and stops pressing tightly against the body over time. Hinges sag from constant slamming: the door droops, and the top and bottom corners no longer line up. The technician inspects the seal for tears, checks hinge play, and examines the door latches that trigger the lock. After replacing hinges and the gasket, we always check the door lock: even a slight misalignment affects how the latches engage and compromises safety. We match parts to the specific model so the seal sits flush across the whole surface without gaps, and the door closes with even resistance around the entire perimeter.
The display and panel on Hansa microwaves are the first to signal a fault. Here's what the codes and flashing mean and when they point to a control board replacement.
A flashing display on Hansa microwaves usually indicates a control board fault or an interrupted power supply, not a heating failure. The board controls the buttons, display, and modes, so when there's a voltage spike or timer glitch, it resets the display and flashes instead of showing a steady countdown. Error codes and indicators vary across Hansa series: a symbol that means a sensor fault on one model may read as a lock signal on another. We cross-check the code against the specific model using service documentation before naming the cause. In practice, a flashing screen often turns out to be a loose ribbon cable contact or a restart after a power failure rather than a board replacement. The code on the screen is a starting point, not a diagnosis: the same symbol can mean different things across Hansa series, so the technician verifies it against the model before drawing conclusions.
If the buttons or touch panel don't respond, in our experience the panel membrane or the control board ribbon cable is usually to blame, while the heating itself may be fine. The membrane is a thin film with conductive traces: it wears out from frequent presses over time, and grease and moisture finish the job. The ribbon cable connecting the panel to the board frays or works loose from the connector, and signals from the buttons stop reaching the controller. On models with a touch panel, there's an additional layer sensitive to contamination: sometimes cleaning and reconnecting the ribbon cable is enough. The panel is tested separately from the high-voltage section: this way the technician knows whether the membrane needs replacing or the board needs repair, and avoids unnecessary parts. Diagnostics will also show whether the heating works — if the magnetron is fine, the owner gets away with restoring the panel.
When neither the display nor the light comes on, we start with the high-voltage fuse and the door interlock: either one can cut power to the entire oven. The fuse protects the circuit from a short and blows first when a capacitor, diode, or magnetron fails. The door latches are the second line of defense: if even one microswitch doesn't engage, the board won't send the start command, and the oven stays silent. The cavity light is checked separately: it may simply have burned out, in which case heating still works but the cavity stays dark. A blown fuse is a symptom, not the cause: putting in a new one will just blow again until the short in the circuit is found. We test the high-voltage components on-site so we can replace both the fuse and the part that tripped it.
Our Hansa microwave service in Almaty follows the same steps whether at your home or in the shop: request, visit, free diagnostics, approval, and repair. Here's what to expect.
We take your request and send a technician to your home within 60 minutes anywhere in the city; if it's more convenient, you can bring the appliance to our service center. Our field technician handles both freestanding and built-in Hansa models, so if your oven is set into a cabinet or niche, let us know when you call so we can plan the removal. The technician travels on their own, so you can just stay home—no need to wait outside. For the visit, we only need the model and a description of the symptom—that's enough for the technician to prepare. We repair Hansa microwaves in Almaty both on-site and in the shop—you choose what works best. Please mention in advance if the oven is built into cabinetry, as that affects the tools and removal procedure. A Tech Service technician arrives with everything needed for the initial disassembly.
Diagnostics are free, and the technician quotes the price after them, once it's clear which part has failed. On site, they remove the cover, check the high-voltage circuits, magnetron, and control board, listen to the transformer, and inspect the waveguide. Then you get a clear explanation: which part failed, whether it needs full replacement or just a local fix. Approving the cost before work starts protects you from surprises: if disassembly reveals a different cause, the technician comes back to discuss the price rather than quietly adding to it. In my experience, this step is what most often puts owners at ease—they see what they're paying for before any work begins. Describe the symptom in as much detail as you can; it speeds up finding the faulty part.
After replacing the part, we test operation and the door interlock to make sure the oven not only turns on but heats safely. The technician reassembles the casing, runs several power settings, and monitors how the magnetron responds under load. The warranty on labor and parts is 1 year, and its terms are recorded right after the check. A test heat-up reveals what you can't see during disassembly: even heating and no recurring arcing. You can pay via Kaspi QR, Kaspi Red (instalments), bank card, cash, or bank transfer for companies, and if the oven is built-in, the technician helps put it back in the cabinet. After reinstalling, the technician checks again that the door closes evenly and the latches engage without effort. The technician shows you the result of the test heat-up on site—so you can see the oven is working and holding the interlock after repair.
Owners care not only about the repair itself but also about the appliance's future. Let's go over the warranty terms, the risks of replacing a magnetron yourself, and situations where you don't need to call a technician.
We provide a 1-year warranty on labor and parts, including magnetron replacement, and we accept Hansa appliances for repair after the manufacturer's warranty expires. Coverage applies to the high-voltage circuit, transformer, waveguide, and door mechanism — everything the technician replaced or adjusted during the visit. We honor warranty claims for the same appliance we serviced. The warranty on a part and on labor are separate things: if a component fails, not only its replacement but also correct installation matters, so both are covered. The warranty covers both the part and its installation, so both risks are addressed. The technician who installed the part is fully responsible for the result — both for the part itself and for the quality of its installation.
| Covered | Term | Condition |
|---|---|---|
| Technician's labor | 1 year | Repair performed by the service |
| Part | 1 year | Installed during repair |
| Magnetron replacement | 1 year | Labor and part together |
Here's a short list of what determines the decision to restore a Hansa microwave: where to look for the cause, what's dangerous to do yourself, and in which cases the appliance is worth repairing.
40brands
Hansa is one of the brands our technicians service. Choose a brand to go to its page.
Tech Service technicians repair other appliances too — with the same 1-year warranty on labour and parts.
Refrigerator Repair in Almatyfrom 3 000 ₸
Washing Machine Repair in Almatyfrom 3 000 ₸
Dishwasher Repair in Almatyfrom 3 500 ₸
Oven Repair in Almatyfrom 3 000 ₸
Cooktop Repair in Almatyfrom 3 500 ₸
Air Conditioner Repair in Almatyfrom 3 500 ₸
Boiler and Water Heater Repair in Almatyfrom 2 500 ₸
Freezer Repair in Almatyfrom 6 000 ₸
Tumble Dryer Repair in Almatyfrom 5 000 ₸
Coffee Machine Repair in Almatyfrom 2 500 ₸
Robot Vacuum Cleaner Repair in Almatyfrom 3 500 ₸
Vacuum Cleaner Repair in Almatyfrom 1 500 ₸
Microwave Oven Repair in Almatyfrom 2 000 ₸
Hair Dryer Repair in Almatyfrom 1 500 ₸
Iron Repair in Almatyfrom 3 000 ₸
Electric Kettle Repair in Almatyfrom 2 500 ₸
Mixer Repair in Almatyfrom 2 500 ₸
Multicooker Repair in Almatyfrom 500 ₸
If your microwave isn't heating but the light and turntable still work, the problem is usually one of the high-voltage components — the magnetron, diode…
15 February 2026 · 12 minutes read
If your dishwasher won't drain, the most common culprits are a clogged filter or drain hose; less often, it's the pump, impeller…
24 March 2026 · 12 minutes read
A washing machine can hum for many reasons, and the first thing to figure out is when the sound appears.
20 March 2026 · 12 minutes read
If your washing machine isn't filling with water, the most common culprits are a closed valve, a clogged inlet filter screen on the hose…
20 February 2026 · 13 minutes read
If your refrigerator stops working, first check the outlet, the power cord, and the thermostat setting, and after defrosting let it stand for a while.
4 February 2026 · 12 minutes read
Washing machine error codes are self-diagnostic codes that point to a specific component: drain, water fill, heating, motor, or door lock.
29 January 2026 · 13 minutes read












