experience9 yearsRuslan Ts.
Washing machine and refrigerator repair technician
City
Language
What broke
Sections
Message on WhatsApp+7 (775) 030 02 94Mon–Fri 10:00–19:00, Sat–Sun 11:00–18:00
A technician arrives within 60 minutes anywhere in the city. Diagnostics are free.
Our own technicians4 to 20 years of experience




Repair prices
Below are frequent symptoms and likely causes. The technician will pinpoint the exact cause during diagnostics.
heating element, switch
from4 000 ₸
thermostat, sensor, heater
from5 000 ₸
plug, power cord, control board
from3 000 ₸
hinges, springs, seal
from5 000 ₸
contacts, switch
from4 000 ₸
worn heater, poor contact
from4 000 ₸
thermostat, relay, control board
from4 000 ₸
current leakage, damaged insulation
from6 000 ₸
The table lists the 'from' price for labor, for common jobs also the 'from' price of the part, plus the time required to complete the job.
1 visittime
from 5 500 ₸cost

BeforeAfter5 steps

Five steps from request to check.
Submit a request and specify the model and symptom.
The technician brings tools and parts and sets up a workspace by the stove.
The technician identifies the cause and gives you the repair cost.
Work begins only after you agree.
The technician demonstrates the stove in action and explains how to use it.
The home appliance repair department in Almaty has 8 technicians with 8 to 12 years of experience.

The department has 8 specializations — they are listed on the technicians' cards.
experience9 yearsWashing machine and refrigerator repair technician
experience12 yearsGeneral household appliance repair technician
experience10 yearsField technician for washing machine and refrigerator repair
experience8 yearsExpert washing machine repair technician
experience8 yearsField refrigerator repair technician
experience8 yearsSenior washing machine repair technician
experience11 yearsDishwasher repair technician
experience9 yearsWashing machine repair technician
We reply during working hours
Submit a request with your stove model and symptom. A technician will arrive within 60 minutes anywhere in the city.

Warranty question? Call us
+7 (775) 030 02 947 898 reviews of repairs at TECH SERVICE in total
Богдан С.Order No. ZK-2026/617 · 17 April 2026
oursТехника на гарантии уже не была, так что выбор был свободный. Проблема — не работает духовка. Сделали и забыл про проблему.
Марина В.Order No. ZK-5769 · 12 January 2025
oursВыбирал по отзывам в 2ГИС, времени на эксперименты не было. С чем пришёл: выбивает. Ребёнок уже проверил на прочность, держиться.
Бакыт Ж.Order No. ZK-2023/229 · 26 November 2023
oursДруг посоветовал, у него похожая история была. Проверил дома — всё на месте, ничего не забыли.
Гульмира С.Order No. TS-2303-526 · 11 April 2023
oursРаботаю допоздна, поэтому нужен был сервис с нормальным графиком. Внешне как новый, если не считать мелкой царапины.
Дамир И.Order No. ZK-4722 · 4 January 2023
oursДруг посоветовал, у него похожая история была. С чем пришёл: не работает духовка. Пользуюсь ежедневно, вопросов нет)
Бакыт Ж.Order No. TS-4826 · 5 September 2022
oursДо этого обращался в другой сервис, там только развели руками. Сначала сомневался, мало ли что. Основная жалоба — не работает духовка. Заявку приняли по телефону, перезвонили через десять минут. Заодно поменяли: термостат. Заплатил 13 500, и не жалею. Спасибо, выручили. Пользуюсь ежедневно, вопросов нет.
Диана М.Order No. TS-7409 · 29 April 2020
oursНужен был счёт и чек, у нас техника на балансе организации. Основная жалоба — не работает духовка. Включил, проверил, работает.
Фарида К.Order No. TS-1911-950 · 18 January 2019
oursПробовал найти мастера в своём районе, но все были заняты. С чем пришёл: не греет конфорка. Работает как раньше, придирок нет
Сабина Г.Order No. TS-5105 · 29 August 2017
oursАсығыс болмасам да, бір күнде бітіретінін айтты. Ұсынамын, текке ақша алмайды.
Максат О.Order No. 2017-1307 · 20 January 2017
oursДруг посоветовал, у него похожая история была. Диагностика плиты — с этого всё началось. Симптом был очевидный: не греет конфорка. Запчасть была в наличии, доплачивать не пришлось. Диагностику сделали бесплатно, хотя я был готов платить. Нагрев в норме, посторонних звуков нет.
Didn’t find the answer? Message us on WhatsApp.
Ask a questionIn Almaty, our service center handles these stoves: a technician comes to your home anywhere in the city. You can request service by phone or on the website, and on-site diagnostics are free.
Yes, a technician comes to you and repairs the stove on site without taking it to the service center. A visit within the city takes about 60 minutes, and diagnostics are free.
Most often this is a faulty relay or thermostat that opens the circuit when it heats up. It depends on the model, so the technician will determine the exact cause during free diagnostics.
Usually it's the burner itself or its switch, less often the wiring to it. The technician will check the circuit and replace the failed component without touching the working burners.
It depends on the model: sometimes the ribbon cable contacts are restored or the control board is replaced, sometimes the entire panel. The technician will inspect the unit and tell you what's more cost-effective in your case.
First check your cookware: induction only works with ferromagnetic bottoms of the right diameter. If the pot is suitable and the stove stays silent, the cause is in the sensor or module — that's already a repair.
Tech Service repairs Beko electric stoves in Almaty at your home and in our service center. Our technician arrives within 60 minutes anywhere in the city, diagnostics are free, and we provide a 1-year warranty on labor and parts. Technicians with 4 to 20 years of experience know Beko stove error codes and common breakdowns.
The stove won't turn on or shows a code on the display — these are different scenarios, and before calling a technician it's important to understand which one occurred.
| Code | What it means | What we check |
|---|---|---|
| F0 | Touch panel failure | Sensor ribbon cable and contacts |
| F1 | Temperature sensor fault | Sensor resistance, connector |
| F3 | Overheating of the cooking zone | Protection circuit and module cooling |
| F5 | Control error | Power supply, traces, relays |
| F7 | Communication failure with module | Connecting ribbon cable between components |
| F9 | Incorrect sensor readings | Sensor seating and wiring |
In our experience, clicking and spontaneous shutdown usually point to a temperature sensor or overheating of the control electronics, which puts the stove into protection mode. The thermostat monitors the cooking zone temperature, and when its readings go beyond the acceptable range, the automation cuts off heating — hence the relay click and a pause in cooking. The second scenario is overheating of the module itself: the power element heats up more during prolonged operation at maximum power, and protection triggers sooner the worse the heat dissipation inside the housing. Load testing shows at what threshold the stove cuts out. If the electric stove turns off specifically under load but works at idle, you should look not at the burner but at the protection circuit — this narrows diagnostics down to one or two components. If self-checks don't help, it's better to entrust Beko electric stove repair in Almaty to a technician experienced with this equipment.
One burner doesn't heat or the touch sensor doesn't respond — the cause depends on the type of Beko stove, and diagnostics differ for classic, glass-ceramic, and induction models.
We test the heating element of the burner with a multimeter: if the heating coil is broken, the heating stops completely, and if the thermostat has tripped, the burner heats weakly or turns off too early. On glass-ceramic cooktops, the same symptom can be caused by delamination of the heating layer under the surface: the zone turns on, the indicator lights up, but there is no heat. On a classic stove, we also check the switch — burnt contacts cause intermittent heating instead of smooth regulation, and a worn shaft does not close the required power level. We check the temperature sensor separately: its resistance changes with temperature, and a stuck sensor cuts off the zone after a couple of minutes of operation. When only one zone does not heat and the others work, the control board is usually not touched — first, they test that specific heating element and its temperature sensor. This order saves time: a faulty burner is replaced entirely, rather than looking for a rare electronic fault.
| Stove type | What breaks most often | What we check |
|---|---|---|
| Classic | Heating element, switch | Coil, contacts, thermostat |
| Glass-ceramic | Heating layer, cracks | Heating zone, surface integrity |
| Induction | Coil, cookware sensor | Bottom of the pot, coil, sensor |
Current leakage to the body and a crack on the cooktop are situations where not only repair but also safety before the technician arrives matters. We explain how the stove behaves and what to do.
We can replace the glass-ceramic surface separately from the rest of the stove — the cooktop itself is changed, while the lower unit and oven stay in place. The glass-ceramic is held by an adhesive layer around the perimeter and connected to the same heating zones, so removal affects only the top assembly. A crack can't be 'healed' with sealant: moisture gets through it to the heating layer, and over time the appliance starts tripping the breaker. That's why the surface is replaced rather than repaired — otherwise you'll have to take the panel apart again in a few weeks. In my opinion, it's not worth delaying the replacement: even a hairline crack expands from heat and temperature changes, and a chip on the edge catches cookware and grows further.
Most Beko electric stove breakdowns are fixed on-site, and it's useful for the owner to know in advance how the visit goes and which components are repaired on the spot.
On-site, we repair classic stoves by checking the heating element and switches, while induction stoves require diagnostics of the coil, cookware sensor, and control module, so the tool set and diagnostic time differ. On a classic stove, the heating element is tested with a multimeter and the switch contacts are inspected: the cause here is usually mechanical — a burned-out coil or a charred terminal. In a Beko induction model, we first read error codes from the electronics, check the coil and the cookware detection sensor, and only then disassemble the burner. Glass-ceramic sits in between: heating comes from a heating element under the glass, but the touch panel adds its own electronics, which are also checked. Induction is more demanding on its internals, so error codes are read before disassembling the burner — this way the component isn't opened unnecessarily and fragile ribbons aren't damaged.
Before requesting service, it's important for the owner to understand how the stove inspection is carried out, how the final amount is agreed, and what obligations the service center has after the work is done.
We provide a 1-year warranty on labor and parts, so if the repaired unit fails again, the stove is re-examined under warranty. The commitment covers two things at once: the part installed in place of the burned-out one, and the technician's work in installing and connecting it. For the owner, this means one simple thing: if the same unit fails again within a year, you won't pay twice for the same fault. Our experience shows that repairs where the whole unit was replaced, rather than individual contacts restored, last the longest. It's best to do the acceptance check right away, with the technician present: turn on the stove, run all burners, and check the heat at each setting — that way you confirm the result while the specialist is still there.
You can pay via Kaspi QR, Kaspi Red (instalments), bank card, cash, or bank transfer for companies, and a technician arrives within 60 minutes anywhere in the city after you request service for your Beko electric stove in Almaty. It's best to include the stove model and a description of the symptom — that way the specialist brings the right tools and knows which circuit to start diagnosing. For Almaty residents, this saves time: no waiting for a second visit because a part or tool is missing. The mobile technician works with classic, glass-ceramic, and induction models, so just specify the cooktop type in your request. It's best to schedule the acceptance check for when you're at home: the inspection, approval, and the work itself are done without rushing, and the 1-year warranty starts from the moment the stove is working again.
There are many appliance technicians in the city, but not everyone knows the specifics of Beko stoves. Here's what to look for so you don't overpay for experiments on your equipment.
The parts we replace most often are the burner heating element, temperature sensor, touch panel, and control board — these are the components that wear out first on Beko stoves. The burner heating element suffers from overheating during intense cooking, the temperature sensor loses accuracy and the stove heats unevenly, while the touch panel and control board fail after power surges and moisture exposure. On glass-ceramic models, damage to the heating element under the glass is added to this, and on induction models, the inverter module. Part compatibility is confirmed after diagnostics based on the stove model: Beko has different modules and heaters depending on the series, so there is no universal part 'for all stoves.' The part number is checked against the specific series — this increases the chance of selecting the right part the first time.
Beko electric stoves fail no more often than other brands, and the nature of the breakdown depends on the stove type and cooking intensity, not on the brand as such. On classic models with an open heating element, the burner burns out after several years of daily use; on glass-ceramic, the heating element under the surface wears out faster, and the touch panel is sensitive to moisture and power surges. Over time, the temperature sensor produces an error, and the stove either underheats or goes into protective shutdown. The components that wear out fastest are those under daily load — burners and touch controls; timely replacement of one part extends the life of the entire stove. When the stove stops heating, the cause is almost always a specific component, not the 'old age' of the appliance as a whole.
Here are the key points a Beko stove owner should keep in mind: where to start when a breakdown occurs, which situations are dangerous, and what signs to look for when choosing a technician.
30brands
Beko is one of the brands we service. The site also has pages for other stove brands.
Tech Service technicians repair other appliances too — with the same 1-year warranty on labour and parts.
Refrigerator Repair in Almatyfrom 3 000 ₸
Washing Machine Repair in Almatyfrom 3 000 ₸
Dishwasher Repair in Almatyfrom 3 500 ₸
Oven Repair in Almatyfrom 3 000 ₸
Cooktop Repair in Almatyfrom 3 500 ₸
Air Conditioner Repair in Almatyfrom 3 500 ₸
Boiler and Water Heater Repair in Almatyfrom 2 500 ₸
Freezer Repair in Almatyfrom 6 000 ₸
Tumble Dryer Repair in Almatyfrom 5 000 ₸
Coffee Machine Repair in Almatyfrom 2 500 ₸
Robot Vacuum Cleaner Repair in Almatyfrom 3 500 ₸
Vacuum Cleaner Repair in Almatyfrom 1 500 ₸
Microwave Oven Repair in Almatyfrom 2 000 ₸
Hair Dryer Repair in Almatyfrom 1 500 ₸
Iron Repair in Almatyfrom 3 000 ₸
Electric Kettle Repair in Almatyfrom 2 500 ₸
Mixer Repair in Almatyfrom 2 500 ₸
Multicooker Repair in Almatyfrom 500 ₸
If your oven isn't working, first check the outlet, the circuit breaker in the panel, and the selected mode, then assess the symptom: not heating…
3 October 2025 · 12 minutes read
If your dishwasher won't drain, the most common culprits are a clogged filter or drain hose; less often, it's the pump, impeller…
24 March 2026 · 12 minutes read
A washing machine can hum for many reasons, and the first thing to figure out is when the sound appears.
20 March 2026 · 12 minutes read
If your washing machine isn't filling with water, the most common culprits are a closed valve, a clogged inlet filter screen on the hose…
20 February 2026 · 13 minutes read
If your microwave isn't heating but the light and turntable still work, the problem is usually one of the high-voltage components — the magnetron, diode…
15 February 2026 · 12 minutes read
If your refrigerator stops working, first check the outlet, the power cord, and the thermostat setting, and after defrosting let it stand for a while.
4 February 2026 · 12 minutes read












