experience14 yearsVladimir D.
Air conditioner service technician
City
Language
What broke
Sections
Message on WhatsApp+7 (778) 746 00 26Mon–Fri 10:00–19:00, Sat–Sun 11:00–18:00
A technician arrives within 60 minutes anywhere in the city. Free diagnostics, 1-year warranty on labor and parts.
Our own technicians4 to 20 years of experience




Repair prices
Below are typical symptoms and likely causes. The technician will pinpoint the exact cause after diagnostics.
no power, faulty board, circuit breaker
from10 000 ₸
refrigerant leak, clogged filter, compressor
from9 500 ₸
clogged drain, shifted pan, freezing
from3 500 ₸
worn bearing, fan imbalance
from8 500 ₸
sensor failure, board fault, communication break
from4 500 ₸
refrigerant leak, valve failure, board
from9 500 ₸
dirty filter, mold in the unit, drain
from3 500 ₸
compressor overheating, board failure, sensor
from4 500 ₸
The table lists the 'from' price for labor, for common jobs also the 'from' price of the part, plus the time required to complete the job.
1–2 hourstime
from 4 500 ₸cost

BeforeAfter5 steps

Five steps from request to performance check.
Leave a request and a technician will arrive within 60 minutes anywhere in the city.
The technician will confirm the time and clarify how to provide access to the indoor and outdoor units.
The owner chooses between repairing the unit and replacing the unit, and the technician explains the difference in labor.
The technician performs soldering, unit replacement, or heat exchanger cleaning on site.
The owner checks that all modes work, there are no leaks, and no unusual noise after turning on.
The climate control equipment repair department in Almaty has 8 technicians with 4 to 20 years of experience.

The department has 8 specializations — they are listed on the technicians' cards.
experience14 yearsAir conditioner service technician
experience20 yearsSenior air conditioner installer
experience12 yearsAir conditioner repair technician
experience16 yearsIndustrial air conditioner technician
experience4 yearsAir conditioner service technician
experience14 yearsAir conditioner maintenance technician
experience5 yearsAir conditioner installation technician
We reply during working hours
Leave a request and get a technician's consultation on your issue.

Warranty question? Call us
+7 (778) 746 00 267 898 reviews of repairs at TECH SERVICE in total
Дамир И.Order No. TS-8340 · 23 July 2024
oursБалалар бар, техникасыз қиын, сондықтан тез жөндеу керек еді. Бағасы базардағыдан қымбат емес. Бағасын бірден айтпады, қайта сұрауға тура келді.
Тимур И.Order No. ZK-7179 · 10 December 2021
oursДо этого обращался в другой сервис, там только развели руками. Первое, что заметил: не холодит один блок. Отдельно скажу про мастера: Дамир М — спокойный, без лишней суеты. Вернули в тот же день, всё функционирует.
Молдир С.Order No. ZK-2021/987 · 3 March 2021
oursПозвонил в три места, здесь единственные назвали цену сразу. Диагностика мультисплит-системы — с этого всё началось. Симптом был очевидный: не холодит один блок. Всё оформили по договору, с печатью. Из деталей — компрессор. Сравнивал с двумя другими — здесь вышло ровнее всех. Шум пропал, работает мягко
Жасмин Р.Order No. 2020-9368 · 25 November 2020
oursПовод для визита: течёт. Дамир М подсказал, как продлить жизнь технике. Внешне как новый, если не считать мелкой царапины.
Акбота Т.Order No. ZK-2020/555 · 20 May 2020
oursСмотрел, у кого есть запчасти на такую модель. Нужен был ремонт мультисплит-системы — обратился сюда. Основная жалоба — ошибка. Нужна была замена: компрессор. Вышло 29 500 тенге, дешевле, чем я рассчитывал. Всё оформили по договору, с печатью. Вернусь, если приспичит. Нагрев в норме, посторонних звуков нет.
Зарина Ш.Order No. ZK-2020/157 · 15 March 2020
oursЦена имела значение, но и гарантия тоже. Проверили на всех режимах, всё чётко
Виктор Ф.Order No. ZK-8231 · 17 February 2019
oursБыло подозрение, что дело в плате, хотелось услышать второе мнение. Жена сказала выкинуть, я решил сначала показать мастеру. Основная жалоба — не холодит. Нагрев в норме, посторонних звуков нет
Ержан А.Order No. ZK-2018/132 · 7 October 2018
oursИскал мастерскую поближе к дому, чтобы не мотаться с техникой через полгорода. Утром столкнулся с тем, что наледь. Созвонились, договорились на удобное время, никто не тянул. Сказали 15 500, а потом ещё и скидку сделали. Деталь на замену — компрессор. Шум пропал, работает мягко.
Гаухар Н.Order No. ZK-2017/967 · 9 September 2017
oursДолго откладывал ремонт, потом всё-таки собрался. Отдал мастеру: мультисплит-система. Симптом был очевидный: не холодит один блок. Дамир М взялся за то, от чего другие отказались. Оплатил картой, чек дали. Разобрали, посмотрели: компрессор. Мастер приехал на дом, всё посмотрел при мне. Единственное — ждал запчасть четыре дня. Ребёнок уже проверил на прочность, держится)
Марат Ж.Order No. TS-1606-118 · 1 July 2016
oursПробовал найти мастера в своём районе, но все были заняты. Сначала просто глючило, потом стало хуже: ошибка. Сначала сказали одно, потом уточнили, но в итоге всё совпало. Заплатил 30 500, и не жалею. Мастер показал, что меняет: плата. Парковки у входа мало, это минус. Включил, проверил, работает
Didn’t find the answer? Message us on WhatsApp.
Ask a questionGree is a Chinese brand and one of the world's largest air conditioner manufacturers. It produces both inverter and standard split systems, and supplies some components to other brands.
Most often it leaks because of a clogged drain or a frozen heat exchanger. Less commonly, the indoor unit is misaligned or the drain pan is damaged. Free diagnostics will pinpoint the exact cause.
Gree control boards are more often restored than replaced: technicians find burned-out components and resolder them. Replacement is needed if the board is flooded or irreparably damaged, which depends on the model.
This behavior is often caused by a faulty temperature sensor, start capacitor, or control board. Sometimes the cause is a refrigerant leak or a clog. Diagnostics will give you the exact answer.
First check whether the protection tripped due to low temperature or a voltage surge. If the indicators don't light up, there's likely a problem with the board or start capacitor, and a technician needs to take a look.
Signs include weak airflow, an unusual odor, freezing, or water droplets. Cleaning is also needed if the air conditioner hasn't been serviced in a long time, but a technician will give you the exact answer after an inspection.
Tech Service repairs Gree air conditioners in Almaty with its own technicians: arrival within 60 minutes anywhere in the city, free diagnostics, 1-year warranty on labor and parts. The technician comes to your home or takes the unit to the service center, and quotes the price after diagnostics. Technician experience is 4 to 20 years.
A symptom alone doesn't name the fault—it helps the technician narrow down the causes. Let's break down common Gree complaints and what's behind them.
When diagnosing a Gree with a 'not cooling' complaint, we first check the refrigerant pressure, compressor starting current, and temperature sensor readings. The compressor compresses refrigerant, and the manifold gauge set shows whether the system holds pressure or if Freon has leaked out. Clamp meters show whether the motor draws starting current or if protection trips and the unit shuts off after a few seconds. We compare thermistor readings with the actual air temperature at the evaporator inlet and outlet—a discrepancy points to the sensor, not the compressor. If the unit doesn't cool after winter, the culprit is often not the motor but a clogged heat exchanger and refrigerant lost over the winter—cleaning and leak detection solve the issue faster than replacing components. If self-checks don't give an answer, a technician performs Gree AC repair in Almaty on-site after free diagnostics.
Gree leaks almost always come from the drain, and noise comes from the fan or vibration of the outdoor unit—both causes are confirmed by the technician on-site. The drainage system removes condensate from the indoor unit by gravity, and if clogged or the pan is misaligned, water runs down the wall instead of outside. The indoor fan, when its bearing wears out, starts humming and rattling, and the outdoor fan blade transmits vibration to the mount—hence the low hum in the room. A heat exchanger with a thick layer of dust adds whistling to the airflow and reduces cooling capacity. Clogged drains and dusty heat exchangers accumulate in Almaty conditions within one season, so it makes sense to combine drain flushing and heat exchanger cleaning with maintenance in one visit.
| Symptom | Likely Cause | What the Technician Checks |
|---|---|---|
| Not cooling | Refrigerant leak, clogged heat exchanger | Circuit pressure, evaporator cleanliness |
| Starts and immediately shuts off | Sensor failure, compressor protection | Thermistor readings, starting currents |
| Leaking water | Clogged drain, misaligned pan | Drain patency, unit tilt |
| Noisy and vibrating | Worn fan bearing | Fan play, outdoor unit mounting |
| Not responding to remote | Control board, signal receiver | Board circuits, IR receiver |
A code on the Gree display is a hint, not a verdict. Let's break down how a specialist reads the fault signal and what they check behind it.
During diagnostics, we read the Gree error code from the display or by the indicator blinking and compare it with the fault table for the specific model. Then the specialist follows the circuit: checks the control board, temperature sensors, and thermistors; for inverter models, the module. Thermistor readings are compared with reference resistances at the current air temperature. If signal exchange between units is interrupted, the fault is recorded on the indoor unit, but the cause is more often in the outdoor unit. The same code on different Gree lines can point to different components, so decoding is done by the unit model, not by a generic table from the internet. Give the specialist the exact model and the value from the display—this shortens fault finding. In our practice, technicians with 4 to 20 years of experience trace such chains faster because they remember typical combinations for specific lines rather than checking generic lists.
| Code group | What it indicates | What the technician checks |
|---|---|---|
| Sensor error | Air or heat exchanger thermistor failure | Sensor resistance, connector contact |
| Unit communication error | No signal exchange between units | Cable, connectors, outdoor unit board |
| Compressor protection | Overload or overheating | Starting currents, circuit pressure |
| Inverter error | Inverter module failure | Module testing, power circuits |
If your Gree shows an error, we recommend not resetting it by restarting multiple times, but writing down the value and telling it to a specialist — this speeds up diagnostics. Resetting without fixing the cause brings the signal back after a few cycles and can finish off a component that could still be restored. Before the visit, turn off the power and do not disassemble the casing yourself: voltage remains on the control board, and improper interference with electronics makes it harder to find the fault. An electronics technician first tests the circuit and checks the thermistor readings, and only then concludes whether parts need replacing. We provide free diagnostics before any work and quote the price after it. By writing down the code, you help reduce time on site: the technician arrives prepared instead of spending the first minutes asking questions again.
An inverter Gree is more complex than a conventional one, and servicing its electronics is a separate job. Here we explain which components are checked during diagnostics and which faults can actually be fixed.
In an inverter Gree, we additionally test the power module and the outdoor unit board, because they control the compressor speed. In a conventional model, the motor works on an on-off principle, and its start is checked directly. In an inverter Gree, power electronics sit between the power supply and the motor: a current converter smoothly changes the shaft speed. Using an electronic board tester, we check the converter output and see whether power reaches the windings. Technicians with 4 to 20 years of experience know how a working component behaves under load and distinguish its failure from motor wear. When such a Gree won't start, the compressor isn't always to blame — often the electronics simply aren't supplying power, and replacing the motor would be unnecessary.
We first diagnose the Gree control board on a test bench and restore it if the fault is local, and we suggest replacement when repair isn't cost-effective. The controller sets compressor and fan modes, and its failure shows up in different ways: the unit won't turn on, loses connection with the remote, or shows an error on the display. An electronics technician uses a multimeter to test traces and components, looking for blown capacitors and breaks. Some failures are blown power circuits after voltage surges, and fixing them costs less than replacing the entire electronics board. If the processor is burned out or multiple trace layers are damaged, soldering won't provide stable operation, and then it makes more sense to install a new unit. The technician quotes the price after free diagnostics, once the cause is identified.
We service Gree server and semi-industrial systems with the understanding that cooling downtime is unacceptable, so we carry out diagnostics as quickly as possible. Gree ducted and semi-industrial systems are designed differently from a household wall-mounted unit: they have a more powerful inverter converter, a larger motor, and supply air automation. A technician arriving within 60 minutes anywhere in the city means your server room doesn't stay without cooling any longer than necessary. In a server room, it's important not only to fix the unit but also to check whether components overheated during downtime—this affects the choice of parts to replace. The compressor and booster are inspected separately after a long shutdown, since overheating affects the condition of the windings and oil. After service, we provide a 1-year warranty on labor and parts and you can pay via Kaspi QR, Kaspi Red, card, cash, or bank transfer.
Our Gree repair follows clear steps—from request and visit to warranty. We show what happens at each stage and what the specialist does before disassembling the unit.
After your request, a Tech Service technician arrives within 60 minutes anywhere in the city and starts with free diagnostics, not by taking the unit apart. First, they check power, modes, and sensor readings, then the pressure in the circuit and the condition of the board—so the cause is found before the casing is removed. Diagnostics before work is needed to avoid replacing parts at random: based on the results, the specialist names the cause and scope of work. They quote the price after diagnostics, when the picture for the specific unit is clear. Then you decide whether to start work immediately or think it over. From our team's experience—4 to 20 years for different employees—half of all requests are resolved with adjustment and cleaning, without replacing parts, and this becomes clear at this step.
We fix most Gree breakdowns on-site, and we take the unit to the service center when a test bench for electronics or work on the circuit is needed. On-site, the specialist replaces sensors, starting elements, the fan, fixes leaks, and charges the circuit. Control boards and inverter modules are easier to test on a bench, so such units go to the service center and return after soldering and testing. Cleaning the heat exchanger and flushing the drain is more cost-effective to do during the same visit as the repair: you don't pay for a second visit or have to disassemble the casing again. In my opinion, this is the most underrated point—a clogged heat exchanger by itself causes a loss of cooling, and the owner looks for a breakdown where there isn't one.
Tech Service provides a 1-year warranty on labor and parts and accepts payment via Kaspi QR, Kaspi Red, bank card, cash, or bank transfer for companies. The warranty also covers installed parts, so if the same unit fails again, the specialist handles it under warranty rather than charging for new work. You can pay in cash, by card, or by transfer—whatever is convenient for the owner; we don't restrict payment methods. We select Gree parts for the specific model so the new unit matches the factory specifications. Kaspi QR, Kaspi Red, card, cash, or bank transfer and the one-year warranty apply to any work—both on-site and after service center visits. A practical tip: keep the date of your request—it makes it easier to confirm a warranty case if the same unit acts up again.
In the Almaty market, both intermediaries and private specialists service Gree. We explain what to look for to avoid overpaying and to get a warranty on the work.
Tech Service works as a direct contractor: our own field technician comes to the call, not an outside subcontractor, so one company is responsible for the work and the warranty. Our technicians have 4 to 20 years of experience, and the 1-year warranty covers both labor and parts. A middleman adds an extra link between the request and the person doing the work: a dispatcher takes the call, passes it to a subcontractor crew, and the warranty gets split between the organizer and the one who actually turns the wrenches. In our experience, this is the main reason Gree owners pay twice — first to the middleman for coordination, then to the direct technician for rework. Ask who exactly will come and who is responsible for the warranty at the request stage: with a direct contractor, the answer is the same for both questions.
Our technician arrives within 60 minutes anywhere in the city, and you can pay via Kaspi QR, Kaspi Red, bank card, cash, or bank transfer for companies. Diagnostics are free: the technician comes, finds the cause, and only then quotes the cost of work. For a Gree unit in a server room or running nonstop, a fast visit is especially important — every minute of downtime adds risk of overheating the compressor and inverter module. We don't divide the city into service zones: we take requests from any district, and the unit is either repaired on-site or taken to the service center as a block. When choosing a contractor, ask whether the visit is included in diagnostics and what payment methods are available on-site — this saves you from extra charges after the work.
Here's the key thing to keep in mind as a Gree owner: how to read symptoms and codes, when you need a workshop, and what to look for when choosing a contractor.
80brands
We work with air conditioners and split systems of every brand sold in Kazakhstan — from Almacom, Gree and Midea to LG, Samsung, Chigo and rare imported makes. Can’t find yours in the list? Call anyway — a technician will come and take a look.
Tech Service technicians repair other appliances too — with the same 1-year warranty on labour and parts.
Refrigerator Repair in Almatyfrom 3 000 ₸
Washing Machine Repair in Almatyfrom 3 000 ₸
Dishwasher Repair in Almatyfrom 3 500 ₸
Oven Repair in Almatyfrom 3 000 ₸
Cooktop Repair in Almatyfrom 3 500 ₸
Air Conditioner Repair in Almatyfrom 3 500 ₸
Boiler and Water Heater Repair in Almatyfrom 2 500 ₸
Freezer Repair in Almatyfrom 6 000 ₸
Tumble Dryer Repair in Almatyfrom 5 000 ₸
Coffee Machine Repair in Almatyfrom 2 500 ₸
Robot Vacuum Cleaner Repair in Almatyfrom 3 500 ₸
Vacuum Cleaner Repair in Almatyfrom 1 500 ₸
Microwave Oven Repair in Almatyfrom 2 000 ₸
Hair Dryer Repair in Almatyfrom 1 500 ₸
Iron Repair in Almatyfrom 3 000 ₸
Electric Kettle Repair in Almatyfrom 2 500 ₸
Mixer Repair in Almatyfrom 2 500 ₸
Multicooker Repair in Almatyfrom 500 ₸
Air conditioner errors are codes on the display or flashing indicators that show which component has failed.
5 March 2026 · 12 minutes read
If your air conditioner is leaking, first turn it off and cut the power, place a container under the drip, and move any wiring away from the water.
19 October 2025 · 12 minutes read
Gas boiler errors are codes on the display or a flashing indicator that point to a specific component: ignition, pressure, draft, sensor, or control board.
10 February 2026 · 11 minutes read












