Open until 19:00+7 (778) 046 88 53Call a technician
TECH SERVICE technician holding an air conditioner indoor unit with its drain hose

12 minutes read

Why the Air Conditioner Is Leaking Water
and How to Stop It

Vladimir D., air conditioner service technician

Author: Vladimir D.,Air conditioner service technician

Published
Updated

Technician’s articleTECH SERVICE02

Where the water comes from and why it ends up in the room

If your air conditioner is leaking, first turn it off and cut the power, place a container under the drip, and move any wiring away from the water. The cause is almost always the drain, filters, refrigerant, or installation. Tech Service arrives within 60 minutes, diagnostics are free, and we provide a 1-year warranty on labor and parts.

Condensate is a normal byproduct of any air conditioner, but a puddle on the floor is not. Let's trace the path of moisture from the evaporator to the drain and see where it breaks and ends up inside the unit.

How condensate forms and where it should go

Moisture from the air settles on the cold evaporator, drips into the drain pan, and flows out through a tube to the outside—as long as this path is clear. The heat exchanger of the indoor unit is cooled below the dew point, so condensate forms on its fins constantly, not just in rainy weather. The collected liquid runs down the inclined plates into the pan under the evaporator, and from there it flows by gravity through the drain tube out of the room. As long as the pan is clean, the drain is not clogged, and the slope is correct, all the condensate goes outside. If the pan overflows, the liquid looks for the nearest way out—through the louvers and the casing, not through the tube—so the leak appears right in the room. A properly working unit accumulates several liters of moisture per day, and all of it must leave the room by gravity.

Why water comes through the louvers with the air

When the drain pan overflows, the fan picks up the moisture and throws it out through the louvers along with the airflow. The impeller of the indoor unit drives cooled air through the heat exchanger at a speed sufficient to tear drops off the edge of the pan if the level has risen above normal. The drops break up, fly through the air duct, and come out through the horizontal and vertical louvers—the reader sees not a stream but scattered splashes and wet streaks on the wall under the unit. This scenario is more common with a severe drain clog or a misaligned unit—liquid accumulates at the edge of the pan, where the airflow blows it off. It's easy to check: if splashes fly from the running fan and the area under the unit is dry, the problem is the water level, not the tube.

Why the leak doesn't show up immediately but 20–40 minutes after turning on

Condensate builds up gradually, so with a partially clogged drain, the water reaches the edge of the pan only after 20–40 minutes of operation. As long as the tube passes at least part of the flow, the excess manages to drain away, and the pan stays on the edge—the level rises slowly as liquid accumulates on the evaporator fins. The delay is a diagnostic sign: an immediate leak points to a misaligned or tilted unit, while a delayed one points to a clog or insufficient drain slope. This sign helps the technician understand where to look before disassembly and avoid wasting time checking a working component. A delayed leak is almost always related to the drain, whereas water pouring immediately after start-up indicates a mechanical displacement of the casing.

Causes of the leak and how to tell them apart by symptoms

Four groups of causes produce a similar picture: a clogged drain, refrigerant leak, installation error, and improper use. Let's look at the signs that help distinguish them so you don't replace parts at random.

Clogged drain or refrigerant leak: how to tell

We distinguish them by the nature of the leak: with a clogged drain, water flows in a steady stream after some time of operation; with a refrigerant leak, the evaporator freezes and drops appear after thawing. A clogged drain tube cannot remove condensate fast enough, and it overflows the pan at the edge of the unit. A refrigerant shortage behaves differently: the heat exchanger gets covered with frost, cooling weakens, and moisture starts dripping when the ice melts. In my experience, a clogged drain is noticeably more common—it produces that steady stream without any frost. With low refrigerant, the unit cools less and gets covered with frost—if the leak is accompanied by weak cooling, we look for a leak, not a clog. If the air conditioner is leaking, these signs help quickly understand what's going on.

Table of causes and signs of a leak

four groups of causes and their distinctive signs
CauseWhen the leak appearsWhat you seeAssociated sign
Clogged drainafter 20–40 minutessteady streamwater at the edge of the drain pan
Refrigerant leakafter defrostdrops and frostweak cooling
Incorrect sloperight after installationpooling near the unitwater at the wall
Dirty filtersduring long operationsplashingevaporator freezing

Why it leaks after refrigerant recharge or filter cleaning

After a recharge, the leak persists if the cause was not the refrigerant but the drain—we check the pipe's patency by pouring water through it before concluding the cause. The technician pours water into the drain pan and watches whether it drains freely: that's how a clogged drain line is found, not by the unit's appearance. Cleaning filters without flushing the drain often leaves the blockage in place, so the leak returns on the very next long run. Dust and slime gradually clog the pipe, and replacing filters alone is not enough. But the opposite also happens: after adding refrigerant, the drops don't stop because the technician treated the symptom, not the cause—in my view, the drain should be flushed before recharging, not after.

What to do in the first minutes when water is already running down the wall

While water is running down the wall, it's more important to remove the risk to wiring and flooring than to find the cause. Here's the order of actions for the first minutes—from cutting power to protecting the finishes.

Cut the power, place a container, keep water away from wiring

  • Cut power to the unit: turn off the air conditioner with the remote, then switch off the breaker in the panel.
  • Place a container: put a basin or bucket directly under the drip, and a cloth on the floor.
  • Protect the wiring: move extension cords and power strips away, check outlets below the unit for moisture.
  • Remove the front panel: gently snap it off and let the contents of the drain pan flow into the container.
  • Blot the wall: collect moisture from the wall and slope so it doesn't soak into the finishes and plaster.
  • Don't turn it on until inspected: restart only after a technician checks it, otherwise the leak will run down the wall again.

Why a leak is dangerous for the wall and electrical system

A constant leak soaks the finishes and reaches the wiring, and moisture near electricity is the main risk—more important than the breakdown itself. Liquid runs down the wall to outlets and extension cords below the unit, and a short circuit here is more dangerous than damaged finishes. Plaster and drywall absorb it slowly and release it over weeks, so stains and peeling wallpaper show up later than the drip itself. In our practice, the walls under the unit on the room side suffer most: condensation from the airflow accumulates there, not just drain water. Moisture softens the putty and insulation in the slope, and mold starts in porous material faster than the wall dries. Even a small drip leaves stains and mold on the surface within days, so don't delay fixing the cause.

When you need a technician urgently, not a delayed visit

If the leak is constant or moisture has reached the wiring, we come first—a technician arrives within 60 minutes anywhere in the city. He identifies the cause on site: a clogged drain, a shifted drain pan, or a refrigerant leak each require different repairs, and our diagnostics are free. We provide a 1-year warranty on labor and parts and accept payment in any convenient way. A delayed visit is justified only when the drip is rare and liquid hasn't reached the electrical system: with a constant flow, water seeps into the ceiling and down to neighbors below, and then restoring the finishes is added to repairing the unit. In a doubtful situation, it's easier to call a specialist right away—on site, he'll tell a clog from a refrigerant leak and say whether any repair is needed at all.

5-minute self-check before calling a technician

A quick check shows whether you can handle it yourself or it's time to call a specialist. We go from simple to complex, without disassembling the unit or using tools.

Step-by-step check from filters to drainage

  • Remove and rinse the filters: use warm water and let them dry completely before putting them back in the unit, otherwise dust will clog the fins again.
  • Inspect the drain pan: there should be no standing water, slime, or dark buildup on the walls and corners.
  • Check the hose for kinks: the drain line should not be bent behind the unit, pinched by furniture, or squeezed in a duct.
  • Assess cooling: weak cooling and frost buildup suggest a refrigerant leak, not a clogged drain.
  • Note the symptoms: when exactly it leaks and how much — these details will speed up diagnostics and narrow down the causes.

How to check drainage by pouring water

We check drainage by pouring water: if it doesn't drain from the pan, the hose is clogged or pinched. We pour water in a thin stream and watch how quickly it drains — standing water and slow drainage immediately point to a clog or kink. In our experience, the most common cause is dust buildup in the bend of the hose at the unit's outlet, less often pinching behind a decorative duct or a shifted drain pan. Pouring also shows the opposite: if drainage is free, the leak is not from the drain, and we look for refrigerant or installation errors. A technician arrives at your home within 60 minutes in the city, diagnostics are free, so you can trust the drain check without risking the pan mounting.

What you can do yourself and what to leave to a technician

You can rinse the filters and remove visible clogs yourself, but checking refrigerant, slope, and disassembling the unit we leave to a technician. A Tech Service technician checks pressure and refrigerant amount with gauges, drain slope with a level, and inspects the pan and heat exchanger after removing the casing. Clogged filters reduce airflow over the evaporator, it freezes, and during defrost water bypasses the pan and goes straight onto the wall. Trying to flush the drain under pressure without experience often dislodges the hose inside the unit — then the leak gets worse and water comes through the louvers. We provide a 1-year warranty on labor and parts, you can pay via Kaspi QR, Kaspi Red (instalments), bank card, cash, or bank transfer for companies, and the technician quotes the price after free diagnostics.

Leaks during heating and seasonal scenarios

In heating mode, the air conditioner runs in reverse cycle, and moisture behaves differently. We explain when drops outside are normal and when water indoors signals a problem.

Why water behaves differently in heating mode

In heating mode, the indoor unit works as a condenser, and the outdoor unit removes condensate and steam, so moisture may appear outside rather than indoors. Refrigerant flows in reverse: the indoor heat exchanger becomes hot, and the outdoor one becomes cold. In winter, the outdoor module periodically defrosts, and meltwater runs down the drain hose or drips from the casing outside. Indoors, with a properly working system, there should be no moisture: warm air does not condense on a heated heat exchanger. Steam and drops from the outdoor unit in winter are normal, but a puddle under the indoor unit almost always points to drainage or installation issues. If it drips outside, it's defrost — no need to worry; if moisture collects indoors, look for the cause in condensate removal.

When a leak in heating mode is a malfunction

If water enters the room in heating mode, we look for a clogged drain or incorrect slope — this is a malfunction, not normal operation. In winter, condensate removal works harder, so a weak slope shows up in cold weather, even though the unit worked without leaks in summer. Liquid accumulates in the pan, overflows, and comes out through the louvers. Our technician checks the hose patency and pan geometry on site and adjusts the slope if necessary. Diagnostics are free, and we arrive within 60 minutes in the city. A weak slope that goes unnoticed in summer causes leaks in winter — check the drain before cold weather sets in, not after the first puddle on the wall. If water appears indoors specifically during heating, don't delay the inspection: in summer this defect doesn't show, but in cold weather it makes itself known with the first thaw.

Seasonal operating mistakes that lead to leaks

  • Open windows: a constant flow of humid air increases condensation on the unit's cold surfaces and speeds up icing.
  • Cooling down to 16 °C: the unit runs at its limit and ices up, and during defrost it adds extra moisture to the drain pan.
  • Frequent switching: modes don't have time to stabilize, and condensate doesn't drain away properly.
  • Dirty filters: a clogged filter speeds up evaporator icing and puts more strain on moisture removal.
  • Closed curtains near the unit: warm air from the radiator builds up around the casing and adds condensation on cold parts.

Prevention and when to call a technician in Almaty

Regular maintenance reduces the chance of leaks next season, and when a leak has already happened, it's important to understand what the specialist will check first and how they work.

Prevention schedule to avoid leaks next season

  • Filters: wash them as they get dirty, at least once a season — a clogged mesh disrupts airflow and causes icing.
  • Drainage: check the tube's patency and slope before the season so condensate drains by gravity, not onto the wall.
  • Evaporator: inspect for icing and dirt — buildup on the fins blocks drainage and causes dripping from the louvers.
  • Unit mounting: check for tilting of the casing, as it makes water run into the room even with a clean drain.
  • Maintenance: do it regularly, not just when there's a leak — a routine check costs less than repairing components after a clog.
  • Seasonal preparation: before the first start, run the unit in test mode and watch for dripping from the drain.

What the technician checks first and how long it takes

We start with the drainage and slope — these are the most common causes — then check the filters and refrigerant pressure to find the source without replacing parts at random. During the inspection, the specialist checks the drain tube for kinks and clogs, assesses the casing slope, removes and washes the filters, and measures pressure in the circuit. Around the city, a technician arrives within 60 minutes, and diagnostics are free — the cause becomes clear before any work. If the leak appeared after installation, we first look at the slope and tube kinks, not the refrigerant: installation errors cause leaks immediately, while refrigerant leaks show up as icing and reduced cooling. In heating mode, the same check is faster — icing is visible within the first minutes.

How we fix the leak and what the warranty covers

We eliminate the cause — clean the drain, restore the slope, or fix the refrigerant leak — and provide a 1-year warranty on labor and parts. First, the specialist clears the drain tube and checks that water drains by gravity, then levels the casing if the unit is tilted, and washes the evaporator and filters. If there's a refrigerant leak, we locate the damage, fix it, recharge the circuit, and then re-measure the pressure. Diagnostics are free, and the specialist quotes the price after them, once the cause is clear; you can pay with Kaspi QR, Kaspi Red, card, cash, or bank transfer. Our employee comes to your home or repairs the unit in the service center — they are the direct contractor, not an intermediary, so the same person who did the inspection is responsible for the result.

Stopping an air conditioner leak

An air conditioner leak almost always has an explanation, and the steps to take are few. Below is a short summary to refer to if water is already coming into the room.

  • Water in the room is not normal: condensate should go into the drain, not through the louvers, so any leak signals a problem.
  • The cause is visible from the signs: a clog, refrigerant leak, incorrect slope, and dirty filters differ in when the leak starts and its nature.
  • The first minutes are about safety: unplug the unit, place a container under the stream, and keep water away from wiring and outlets.
  • Self-diagnostics are brief: you can check filters and visible drain clogs yourself, but refrigerant leaks and the drain tube slope are best left to a technician.
  • Prevention is cheaper than repair: servicing once a season reduces the risk of repeated leaks and extends the life of components.

Our technicians in Almaty

01 / 08
Vladimir D., air conditioner service technicianexperience14 years

Vladimir D.

Air conditioner service technician

Mikhail K., senior air conditioner installerexperience20 years

Mikhail K.

Senior air conditioner installer

Rashid I., air conditioner repair technicianexperience12 years

Rashid I.

Air conditioner repair technician

Konstantin K., industrial air conditioner technicianexperience16 years

Konstantin K.

Industrial air conditioner technician

Rauan N., air conditioner service technicianexperience4 years

Rauan N.

Air conditioner service technician

Timur B., air conditioner maintenance technicianexperience14 years

Timur B.

Air conditioner maintenance technician

Ildar S., climate control system repair technicianexperience7 years

Ildar S.

Climate control system repair technician

Mukhamedzhan B., air conditioner installation technicianexperience5 years

Mukhamedzhan B.

Air conditioner installation technician