experience14 yearsVladimir D.
Air conditioner service technician
City
Language
What broke
Sections
Message on WhatsApp+7 (778) 746 00 26Mon–Fri 10:00–19:00, Sat–Sun 11:00–18:00
Free diagnostics, a technician arrives within 60 minutes anywhere in the city. 1-year warranty on labor and parts.
Our own technicians4 to 20 years of experience




Repair prices
The symptoms that most often prompt a service call, and the likely causes. The technician identifies the exact cause after diagnostics.
Refrigerant leak or dirty filter
from9 500 ₸
Clogged drain or misaligned tray
from3 500 ₸
Power supply or control board issues
from10 000 ₸
Worn bearings or mounts
from8 500 ₸
Sensor or control module failure
from4 500 ₸
Compressor or heating element fault
from15 500 ₸
Mold in the evaporator or drain
from3 500 ₸
Overheating or protection trip
from10 000 ₸
The table lists the 'from' price for labor, for common jobs also the 'from' price of the part, plus the time required to complete the job.
1–2 hourstime
from 4 500 ₸cost

BeforeAfter5 steps

From request to performance check — a clear sequence of steps.
Describe the symptom and your air conditioner model so the technician brings the right tools.
The technician inspects both units and gives a preliminary diagnosis.
The technician explains the cause and cost, and starts work only after you agree.
Fixes the fault and replaces worn components if needed.
The technician starts the split system and checks cooling and heating together with you.
The climate control equipment repair department in Almaty has 8 technicians with 4 to 20 years of experience.

The department has 8 specializations — they are listed on the technicians' cards.
experience14 yearsAir conditioner service technician
experience20 yearsSenior air conditioner installer
experience12 yearsAir conditioner repair technician
experience16 yearsIndustrial air conditioner technician
experience4 yearsAir conditioner service technician
experience14 yearsAir conditioner maintenance technician
experience5 yearsAir conditioner installation technician
We reply during working hours
Leave a request — a technician will arrive within 60 minutes anywhere in the city. Diagnostics are free, and they will agree on the next steps with you on site.

Warranty question? Call us
+7 (778) 746 00 267 898 reviews of repairs at TECH SERVICE in total
Богдан С.Order No. ZK-2025/276 · 15 December 2025
oursПозвонил в три места, здесь единственные назвали цену сразу. Первое, что заметил: не холодит. Проверили при мне, показали, что всё держит.
Евгений М.Order No. TS-8391 · 27 April 2024
oursМастер үйге келіп, орнында тексерді. Ұсақ ақауларды да тегін жөндеп берді. Бағасы мен сапасы сай.
Ержан А.Order No. 2022-1408 · 8 June 2022
oursРаботаю допоздна, поэтому нужен был сервис с нормальным графиком. Основная жалоба — не холодит один блок. Tech-service посоветовали в чате дома, спосибо им. Починили и дали гарантию на месяц!!
Эльмира Т.Order No. ZK-3396 · 2 March 2022
oursПозвонил в три места, здесь единственные назвали цену сразу. Работает как раньше, придирок нет.
Данияр С.Order No. 64342 · 17 April 2020
oursПрочитал кучу отзывов, половина — реклама, но тут вроде живые. Позвонил, описал проблему, сказали привозить — посмотрят в тот же день. Внешне как новый, если не считать мелкой царапины)
Томирис Ж.Order No. ZK-2020/288 · 14 March 2020
oursСимптом был очевидный: не холодит. Дамир М перезвонил, когда всё было готово. Работает даже тише, чем до поломки
Мирас С.Order No. ZK-2019/494 · 29 August 2019
oursДамир М снял деталь, показал износ, вопросов не осталось. Включил, проверил, работает.
Светлана Д.Order No. ZK-2019/535 · 5 April 2019
oursДруг посоветовал, у него похожая история была. Поставили новую деталь: компрессор. Сказать, что доволен — ничего не сказать.
Алишер У.Order No. TS-1705-145 · 18 February 2017
oursДо этого обращался в другой сервис, там только развели руками. Записался на диагностику кондиционера. Повод для визита: не холодит. Внешне как новый, если не считать мелкой царапины.
Мадина Т.Order No. TS-3191 · 7 July 2016
oursБұрын осында ноутбук жөндеткенмін, сондықтан сеніммен келдім. Алдын ала айтқан уақыттан ерте бітірді. Ұсақ ақауларды да тегін жөндеп берді. Бағасын алдын ала келістік, соңында өзгерген жоқ. Тексеру кезінде бәрін өзі көрсетті. Қайта жүгінсем, осында келемін
Didn’t find the answer? Message us on WhatsApp.
Ask a questionLook for a service that works directly with air conditioners, without middlemen, and knows the Electrolux brand. At Tech Service, our technician will come to you within 60 minutes, and diagnostics are free.
Freon refilling is done right at your home: the technician arrives with everything needed and first checks the system for leaks. If freon is leaking, the cause is fixed first, otherwise refilling won't help.
Yes, the board is replaced separately from other components if diagnostics confirm it's faulty. We first check the power supply, sensors, and contacts, and only then suggest replacing the unit.
Most calls are about freon leaks, clogged drainage, worn-out start capacitor, and control board failures. It depends on the model and operating conditions; free diagnostics will pinpoint the exact cause.
Yes, the compressor is replaced separately if the other components are working and the repair is justified. It depends on the model: on older split systems, replacing the compressor sometimes costs more than the unit itself.
Water doesn't drain and starts overflowing the drain pan, dripping onto the wall and furniture, and dampness and mold appear inside the unit. Cleaning the drain at your home solves the problem faster than waiting for it to leak more.
Tech Service repairs Electrolux air conditioners in Almaty: our own technician comes to your home within 60 minutes, diagnostics are free, and there is a 1-year warranty on labor and parts. Technicians with 4 to 20 years of experience will decode the error code, find the cause of the breakdown, and agree on the scope of work before starting the repair.
Symptoms with Electrolux air conditioners fall into a few recurring scenarios. Let's break down what each one means and where to start checking.
Most often, we find three causes of no cooling in Electrolux units: refrigerant leak, dirty evaporator filter, and faulty temperature sensor. Frost on copper pipes and the evaporator confirms refrigerant leak, while a steady flow of warm air without condensation points to clogged filters or a faulty temperature sensor. If the unit starts and shuts off after a few seconds, it's almost always compressor protection, and repeated restarts before diagnostics only accelerate wear on the component. A Tech Service technician first checks circuit pressure and heat exchanger condition rather than replacing parts at random. In my view, it's useful for owners to remember a simple rule: the sooner you call a specialist at the first signs, the lower the final repair cost. Our diagnostics are free, and a technician visit takes up to 60 minutes anywhere in the city.
Leaks in Electrolux units are almost always due to a clogged drain system or a displaced drain hose, not a breakdown of the unit itself. The indoor unit collects condensate in a pan, and when the drain is clogged, water overflows and runs down the wall onto the floor. Smell from the unit usually comes from a dirty evaporator and stagnant water in the pan, so cleaning the drain without flushing the heat exchanger gives only a temporary effect. Our technician removes the drain, flushes the pan, and treats the evaporator with an antibacterial solution—otherwise the smell returns in a couple of weeks. It's easy to check: if after the first cleaning the musty smell returns within a week, the problem is in the heat exchanger, not the hose. Moisture on the floor under the unit is also dangerous because it gradually soaks into the wall and joints—it's better to fix it before stains appear.
Noise and vibration in Electrolux units usually come from the fan and loose mounts, while no response to the remote points to the control board or the remote itself. Rattling occurs when the fan wheel is unbalanced, motor bearings are worn, or the indoor unit is loosely mounted to the wall. The remote stops controlling the unit for various reasons: dead batteries, reset settings, or a damaged IR receiver on the board. Before replacing the board, we check power and the IR receiver, because some "dead" remotes are fixed by replacing batteries and resoldering the receiver module. In our practice, half of remote-related calls are resolved without replacing expensive components—so start diagnostics with batteries and cleaning contacts, not with buying a new board.
A code on the display is a hint, not a verdict. Let's break down how we read Electrolux codes, what free diagnostics includes, and why simply refilling refrigerant doesn't solve the problem.
An error code on the Electrolux display points to a specific component—temperature sensor, control board, compressor, or communication between units—and we decode it before the visit so the technician brings the right parts. Combinations on the indoor unit panel fall into groups: evaporator and condenser temperature sensor failures, data exchange errors between outdoor and indoor modules, compressor protection for current and overheating. Each group narrows the search to two or three elements, not the whole system. Moreover, the same combination can mean different things across Electrolux series, so we check it against the model, not a generic code table. Sometimes it's enough to compare the number with the specific unit's manual to avoid replacing a working component—in my view, this is the most common cause of unnecessary replacements.
Refrigerant in an Electrolux air conditioner is not consumed during normal operation, so it needs to be recharged after a leak is fixed, not on a schedule. The refrigerant circulates in a closed loop between the evaporator and condenser, and if the volume doesn't change for years, a pressure drop means the system has lost its seal — a joint, a flare connection, or a microcrack in the tubing. We first find and fix the leak, vacuum the circuit, and only then recharge to the specified weight, not "by eye" using a gauge. If the cooling disappears a month or two after recharging, the leak wasn't fixed, and topping up again without pressure testing only delays the repair. Nitrogen pressure testing before recharging costs less than a second visit and protects the compressor from running with an insufficient charge.
At our service, Electrolux air conditioner repair in Almaty follows one scenario — from the request and a technician's visit to the warranty. Let's walk through each step so you know what happens to your equipment and when.
We come to your home anywhere in the city within 60 minutes, and if the fault requires bench work, we take the air conditioner to the workshop and return it after repair. The field technician brings tools to check the electrics, circuit pressure, and drainage condition right to your door. At your home, they remove the indoor unit, test the control board, check the temperature sensors and refrigerant pressure, and inspect the heat exchanger for dirt. If the compressor is faulty or the circuit needs brazing, the unit is transported to the Tech Service workshop, where work is done on stationary equipment. Most Electrolux faults — refrigerant leaks, clogged drainage, board issues, sensors — are fixed on site, so only a smaller share of requests goes to the workshop. Before the visit, tell us the model and the symptom — this helps us bring the right parts and finish the job in one visit.
Repair time depends on the component — a board, sensor, or drain issue can be handled in a single visit, while compressor replacement takes longer and requires separate approval. The control board and temperature sensors are replaced without opening the refrigerant circuit, so the technician can complete such work on-site. A clogged drain system is flushed in place if the tube is accessible; if it's concealed, part of the duct may need to be removed. Compressor and circuit brazing are bench work at the service center, where pressure and tightness are checked after reassembly. The exact timeframe is given by the technician after diagnostics, because some 'quick' failures actually require checking the entire circuit — from power supply to compressor. Schedule your visit in advance during the hot season: on peak days, the queue for visits stretches out, and it's better not to wait until the equipment completely fails.
Inverter Electrolux units are more complex than conventional split systems, so let's break down how their maintenance differs, when to replace the compressor, and when to replace the entire unit.
In inverter Electrolux units, an inverter board replaces the simple contactor, so diagnostics start with the electronics, not the compressor. This module controls the shaft speed: it smoothly varies the RPM rather than starting the motor with a jolt, as in conventional models. Because of this design, the technician first reads error codes from the display, checks the power supply at the module input and the integrity of the power switches, and only then moves on to the windings and circuit pressure. A significant portion of our visits for this brand are for inverter Electrolux models — their electronics are more tightly integrated with the motor than in budget on/off models. The inverter module is sensitive to voltage spikes, and some 'dead' compressors turn out to be electronics failures — we check that before recommending replacement of the unit.
Restoration makes sense when the failure is local — control module, sensor, drain, or refrigerant leak; replacing the entire unit is reasonable when the compressor and heat exchanger are both damaged. The compressor, condenser, and evaporator are the most expensive components of the circuit, and their simultaneous failure usually means that repairing the equipment is not economically feasible. For a single leak or a burned-out temperature sensor, a new split system is not needed: the technician fixes the cause and checks the other components. The decision should be based on several factors — the age of the unit, the type of failure, and how many components have already been replaced; one expensive repair doesn't always mean the equipment has 'served its time.' In my opinion, there's no need to rush to the conclusion 'it's easier to buy a new one' until all components have been checked.
| Job | What we check | Where performed |
|---|---|---|
| Refrigerant recharge | pressure, leaks, freezing | on-site |
| Drain cleaning | drain pan, hose, odor | on-site |
| Control board replacement | power, inverter, receiver | on-site or at the service center |
| Compressor replacement | start relay, windings, pressure | at the service center |
| Temperature sensor replacement | resistance, error codes | on-site |
Warranty and technician qualifications are the two criteria most often used when choosing a service center for climate control equipment. Let's look at both: what exactly the warranty covers and how to tell a brand specialist.
We give a 1-year warranty on labor and parts, so if the same issue comes back, the visit and repeat repair are covered by the warranty. The obligations are tied to a specific component: replacing the control board, compressor, fan, or temperature sensor — each item is covered separately. Technicians with 4 to 20 years of experience handle these cases themselves, without passing them to third parties. The parts warranty matters separately from the labor warranty because some failures are caused by the part itself, not by the quality of installation — on a repeat visit, we first check whether the component itself failed, and only then look for an installation error. This rule saves time for both sides: you don't have to go through a full diagnostic of a working circuit again.
Tech Service is a direct contractor: our own technician comes to your home, not a subcontractor from a catalog, so one company is responsible for the work and the warranty. This is how Electrolux air conditioner repair in Almaty is handled without a chain of intermediaries: the request is taken by the same service whose specialist is responsible for the result. We accept payment via Kaspi QR, Kaspi Red (instalments), bank card, cash, or bank transfer for companies, and the technician gives you the price after free diagnostics. With an aggregator, a dispatcher takes the request and passes it to a subcontractor, and the warranty applies to the subcontractor, not the platform — it's worth clarifying this before booking so you don't have to look for someone to blame if the problem comes back. In the city, our visit takes 60 minutes, and the same person who handled your request by phone works on site — this eliminates any gap between what was promised and what was done.
Electrolux air conditioner repair comes down to a few clear scenarios: it's important to read the symptom correctly, avoid replacing parts at random, and understand where on-site work ends.
80brands
We work with air conditioners and split systems of every brand sold in Kazakhstan — from Almacom, Gree and Midea to LG, Samsung, Chigo and rare imported makes. Can’t find yours in the list? Call anyway — a technician will come and take a look.
Tech Service technicians repair other appliances too — with the same 1-year warranty on labour and parts.
Refrigerator Repair in Almatyfrom 3 000 ₸
Washing Machine Repair in Almatyfrom 3 000 ₸
Dishwasher Repair in Almatyfrom 3 500 ₸
Oven Repair in Almatyfrom 3 000 ₸
Cooktop Repair in Almatyfrom 3 500 ₸
Air Conditioner Repair in Almatyfrom 3 500 ₸
Boiler and Water Heater Repair in Almatyfrom 2 500 ₸
Freezer Repair in Almatyfrom 6 000 ₸
Tumble Dryer Repair in Almatyfrom 5 000 ₸
Coffee Machine Repair in Almatyfrom 2 500 ₸
Robot Vacuum Cleaner Repair in Almatyfrom 3 500 ₸
Vacuum Cleaner Repair in Almatyfrom 1 500 ₸
Microwave Oven Repair in Almatyfrom 2 000 ₸
Hair Dryer Repair in Almatyfrom 1 500 ₸
Iron Repair in Almatyfrom 3 000 ₸
Electric Kettle Repair in Almatyfrom 2 500 ₸
Mixer Repair in Almatyfrom 2 500 ₸
Multicooker Repair in Almatyfrom 500 ₸
Air conditioner errors are codes on the display or flashing indicators that show which component has failed.
5 March 2026 · 12 minutes read
If your air conditioner is leaking, first turn it off and cut the power, place a container under the drip, and move any wiring away from the water.
19 October 2025 · 12 minutes read
Gas boiler errors are codes on the display or a flashing indicator that point to a specific component: ignition, pressure, draft, sensor, or control board.
10 February 2026 · 11 minutes read












