experience14 yearsVladimir D.
Air conditioner service technician
City
Language
What broke
Sections
Message on WhatsApp+7 (778) 746 00 26Mon–Fri 10:00–19:00, Sat–Sun 11:00–18:00
We'll get your split system running again on site. Free diagnostics, technician arrives within 60 minutes anywhere in the city.
Our own technicians4 to 20 years of experience




Repair prices
Below are common symptoms and likely causes. The technician will pinpoint the exact issue after diagnostics.
refrigerant leak, clogged filter, compressor
from9 500 ₸
clogged drain, unit misalignment
from3 500 ₸
power supply, remote, control board
from10 000 ₸
fan, mounting, bearing
from8 500 ₸
code points to a component, needs decoding
from10 000 ₸
clogged filter, fan
from8 500 ₸
stagnant drain, dirty evaporator
from3 500 ₸
compressor overheating, sensor
from4 500 ₸
The table lists the 'from' price for labor, for common jobs also the 'from' price of the part, plus the time required to complete the job.
1–2 hourstime
from 9 500 ₸cost

BeforeAfter5 steps

From request to post-repair check of your air conditioner.
Describe the symptom and model — the technician will prepare tools and clarify details.
Provide access to the outdoor unit, tell us the model and symptoms — the technician will arrive prepared.
The technician finds the cause and quotes the cost of labor and parts.
You approve the scope of work and cost, then the technician starts.
The technician will agree on a convenient time and ask you to provide access to the outdoor unit.
The climate control equipment repair department in Almaty has 8 technicians with 4 to 20 years of experience.

The department has 8 specializations — they are listed on the technicians' cards.
experience14 yearsAir conditioner service technician
experience20 yearsSenior air conditioner installer
experience12 yearsAir conditioner repair technician
experience16 yearsIndustrial air conditioner technician
experience4 yearsAir conditioner service technician
experience14 yearsAir conditioner maintenance technician
experience5 yearsAir conditioner installation technician
We reply during working hours
Leave a request — the technician will arrive within 60 minutes anywhere in the city. 1-year warranty on labor and parts.

Warranty question? Call us
+7 (778) 746 00 267 898 reviews of repairs at TECH SERVICE in total
Владимир Н.Order No. 71685 · 30 August 2025
oursДо этого обращался в другой сервис, там только развели руками. После выходных обнаружил: шумит. Ни копейки сверху, как и обещали. Из деталей — плата. Мастер сразу сказал, что к чему, без размытых формулировок. Проверил дома — всё на месте, ничего не забыли
Фарида К.Order No. ZK-2021/740 · 4 May 2021
oursНужен был счёт и чек, у нас техника на балансе организации. Жалоба простая: не включается. Пользуюсь ежедневно, вопросов нет.
Динара М.Order No. ZK-9415 · 1 February 2021
oursХотел сначала вызвать мастера на дом, потом передумал. Основная жалоба — течёт. Сделали и забыл про проблему
Николай Ч.Order No. 882288 · 21 September 2020
oursПоломка застала перед командировкой, тянуть было нельзя. Диагностика кондиционера — с этого всё началось. Проблема — ошибка. Никита М не стал навязывать дорогую запчасть, поставил нормальную. Поменяли: компрессор. Вышло 12 000 тенге, дешевле, чем я рассчитывал. Созвонились, договорились на удобное время, никто не тянул. Сделали аккуратно, следов разборки не видно.
Гульмира С.Order No. TS-2001-181 · 13 January 2020
oursБыло подозрение, что дело в плате, хотелось услышать второе мнение. Больше всего напрягало: не холодит. Починили и дали гарантию на месяц.
Куаныш Б.Order No. TS-6861 · 13 April 2018
oursҚұрылғы ескі болғандықтан, бөлшек табыла ма деп қорықтым. Бірнеше жерге қоңырау шалдым, осында ғана нақты айтты. Мастер жарты сағатқа кешікті, бірақ қоңырау шалды)
Алмас Д.Order No. ZK-2018/469 · 27 March 2018
oursПозвонил знакомому, он раньше работал в сервисе, посоветовал этих. Честно, уже готовился покупать новое, но обошлось. Жалоба простая: не холодит. Дамир М перезвонил, когда всё было готово. Проверил дома — всё на месте, ничего не забыли
Ержан А.Order No. 2017-9995 · 12 July 2017
oursПриехал из командировки, а дома — течёт. Приняли, выдали квитанцию, всё по-человечески. Включил, проверил, работает
Юлия А.Order No. TS-1610-389 · 1 February 2016
oursДруг посоветовал, у него похожая история была. Привёз на диагностику: мультисплит-система. Первое, что заметил: ошибка. Посмотрели, назвали срок — два дня. Под замену пошло: плата. Цену обсудили до начала, сюрпризов не было. Однозначно да. Гудит ровно, не грееться, всё как надо.
Фарида К.Order No. ZK-2016/289 · 31 January 2016
oursНикита М принял, посмотрел и сразу сказал, что делать. Сказали 12 000, я согласился без торга. Крутит ровно, без рывков.
Didn’t find the answer? Message us on WhatsApp.
Ask a questionAmong Hyundai models, the affordable options are usually entry-level split systems with a basic set of features. It's best to choose a specific model based on the room's area and your budget, not just the price.
The technician checks the refrigerant pressure, the condition of the compressor, the inverter board, and the sensors. Diagnostics are free, and based on the results, they identify the exact cause and how to fix it.
Weak cooling, frosting on the pipes, and frequent compressor shutdowns indicate low refrigerant. A pressure measurement during diagnostics gives the exact answer.
In a sealed circuit, refrigerant isn't consumed and lasts for the entire service life of the air conditioner. If it runs out within one or two seasons, there's a leak that needs to be found.
The board can be restored if the damage is localized and components are available. If there are burned areas or a rare microchip, it's replaced with a new one. The decision depends on the model and the board's condition.
Most often, the cause is a faulty inverter board, a compressor breakdown, or a short circuit in the wiring. Until the technician arrives, don't turn on the air conditioner to avoid damaging the electronics.
Tech Service repairs Hyundai air conditioners in Almaty with its own technicians who have 4 to 20 years of experience. A technician arrives at your home within 60 minutes anywhere in the city or takes the equipment to the service center. Diagnostics are free, there is a 1-year warranty on labor and parts, and the cost is quoted after diagnostics.
The owner notices the symptom before understanding its cause. We break down common Hyundai complaints — from warm air to drips from the unit — and what each one points to.
Most often, "blows but doesn't cool" is caused by a refrigerant leak, clogged filters, or a failed heat exchanger temperature sensor. Refrigerant circulates in a closed loop of the split system, and through a microcrack in the tube, pressure gradually drops: first the unit works worse, then the compressor goes into protection. Clogged filters give a similar effect — there is airflow, but it doesn't pass through the heat exchanger and doesn't have time to cool. The third scenario is the heat exchanger temperature sensor: the board receives incorrect data and doesn't let the compressor reach cooling mode, even though the expansion valve is working. Technicians in Almaty start with measuring pressure in the loop. If cooling returns for a week or two after refilling, look for a leak in the loop instead of repeating the refill — otherwise the refrigerant will escape again, and the compressor will run dry. In such cases, Hyundai air conditioner repair in Almaty starts with finding the leak, not with a repeat refill.
Spontaneous shutdown and failure to start in Hyundai units are usually related to board protection, a start capacitor, or voltage drop. The inverter board controls compressor speed and, when a parameter goes beyond acceptable values, cuts power — the unit turns off and after a while tries to start again. The start capacitor loses capacitance over time: the compressor hums but doesn't start, and protection triggers again. Voltage drop in electrical circuits gives the same symptom when other powerful consumers are on the line. In inverter models, the board is the most loaded component, and its failure is often disguised as a "burnt compressor." If the inverter unit trips the breaker at startup, before calling a technician, check whether powerful appliances are on the same line: a microwave, heater, or pump can cause that same voltage drop.
Drips from the unit indicate a clogged drain or freezing of the heat exchanger, while noise and vibration usually come from the fan and mounting. The drainage system removes condensate by gravity, and when the drain is clogged, water looks for a way out through the unit instead of outside. On models with a drain pump, a pump failure adds to this — then liquid stays in the pan and overflows. Freezing of the heat exchanger gives a second wave of drips after defrosting, and by this sign it's easy to distinguish a clogged drain from a lack of refrigerant. Noise and vibration are most often related to the indoor unit fan: bearing wear causes humming, loose mounting causes rattling of the unit. Vibration that appears after installation isn't fixed by replacing parts — first check how the unit is mounted.
The code on the display is a hint, not a verdict. We explain how a technician reads a Hyundai error and why decoding without checking components solves nothing.
We decode the Hyundai error code using service documentation and immediately check the component it points to, rather than replacing the part blindly. The indoor unit display or remote shows a combination like E1, E5, CH, and each is tied to a specific circuit: air temperature sensor, heat exchanger sensor, control board, communication line between units. Hyundai inverter models can show an error even when the component is working — due to an oxidized connector, a frayed wire, or a failure after a power surge. Therefore, the technician first tests the wiring from the connector to the board with a multimeter, compares the sensor resistance with the table value, and only then draws a conclusion about the part. The same code can appear due to the sensor and due to the board, so decoding without testing often leads to unnecessary replacement.
| Symptom | Likely cause | What we check |
|---|---|---|
| Blows but doesn't cool | Refrigerant leak, sensor, expansion valve | Circuit, temperature sensors |
| Won't turn on | Board, start capacitor | Power, board |
| Turns off by itself | Board protection, overheating | Board, heat exchanger |
| Water dripping | Clogged drain, frost buildup | Drain, heat exchanger |
| Noisy and vibrating | Bearing, mounting | Fan, unit mounting |
| Trips the breaker | Inverter board, wiring | Board, electrical lines |
We break down the components that most often fail in Hyundai units and explain where repair is possible and where a new part is needed to replace the failed one. For each component, we show what the technician checks and how the work is performed.
We first test the Hyundai inverter board and assess whether repair is possible, and only if it's not feasible do we suggest installing a new unit. Diagnostics cover power circuits, output switches, and the surrounding power components — that's where traces most often burn out after voltage spikes in the grid. The board controls the compressor speed, so its failure often masquerades as a "won't turn on" or "turns off after a minute" symptom. A test run helps distinguish a board failure from a compressor failure: a board without a working compressor won't show the real picture. In my opinion, repairing the board is almost always more cost-effective than buying a whole unit — provided the power switches haven't burned out along with the traces. A 1-year warranty on labor and parts applies in this case as well.
We only refill refrigerant after finding the leak, vacuuming, and charging by weight, and the compressor and four-way valve are checked during a test run. The compressor is assessed by starting current and circuit pressure: if pressure doesn't rise while the fan is running, the component is suspect. The four-way valve switches between cooling and heating modes, and if it jams, you get airflow without temperature change. We locate leaks at joints and flare fittings, not by overall pressure drop. Frequent top-ups without leak detection are money down the drain: refrigerant escapes through a leaky circuit, it doesn't "evaporate" on its own. That's why before any refill we pinpoint the loss and fix it.
| Component | What we check | Work options |
|---|---|---|
| Inverter board | Continuity, power circuits | Repair or replacement |
| Compressor | Start-up, current, pressure | Repair or replacement |
| Temperature sensors | Signal to the board | Sensor replacement |
| Drainage system | Flow, pump | Cleaning, replacement |
| Fan and mounting | Bearing, vibration | Repair, adjustment |
| Refrigerant circuit | Leak, evacuation | Leak detection, recharge |
We walk you through the service process: how a technician visit works, what they check during free diagnostics, and when the unit goes to the service center instead of being fixed on site.
Our technician arrives at your home within 60 minutes anywhere in the city and performs diagnostics on site. We take the unit to the service center when a component needs repair that can't be done on site. The visiting specialist does diagnostics on site, so typical failures are fixed right at the client's place. The unit is sent to the service center if the board needs repair, the compressor needs replacement, or the circuit needs pressure testing to find a microleak — such operations are not done on site. The indoor unit mounting is secured separately during removal: broken brackets later cause the body to misalign and vibrate. You don't need to remove the unit yourself: the technician determines the scope of work after inspection to avoid damaging the mounting and circuit. If service center repair is needed, the technician carefully removes the indoor and outdoor units, packs the components, and returns the equipment after restoration.
We separate cleaning and repair: antibacterial cleaning of the heat exchanger is preventive maintenance, while repair fixes a specific component failure. Washing the evaporator and filters removes odors, restores airflow, and reduces load on the fan, but it does not affect circuit pressure. If the unit doesn't cool due to a refrigerant leak, cleaning the heat exchanger alone won't solve the problem — the refrigerant will continue to escape through the leaky connection. Our technicians first perform diagnostics, then offer cleaning as a separate service or component restoration based on the actual condition of the equipment. There's no point in ordering a wash to fix a display error: it masks the symptom while the cause remains. Cleaning does not replace repair: if the unit doesn't cool due to a refrigerant leak, washing the heat exchanger won't solve the problem.
We explain what protection the warranty on labor and parts provides, how we handle repeat errors, and why the direct contractor is fully responsible for the result.
We provide a 1-year warranty on labor and parts, so both the service of the unit and the installed part are equally protected. The inverter board, compressor, four-way valve, temperature and pressure sensors, starting automation — each replaced or restored element is covered for the same twelve-month period. When a warranty claim is made, the technician checks which unit was replaced and what operation was performed, so it is clear what the warranty covers and what exactly needs to be rechecked. The warranty on parts is just as important as the warranty on labor: if a part fails, the issue is resolved within a single request — there is no need to separately prove that the cause is the part itself and not the installation or adjustment.
If the same error appears again after Hyundai service, we return to diagnostics and check the unit anew rather than just replacing the part again. First, the technician reads the current code from the display and compares it with the one before the repair, then tests the board circuit and inspects the connector contacts for oxidation and looseness. A recurring error often points to a related failure that did not show up during the first test run: for example, a weakened capacitor on the board only fails under load when the compressor reaches full power, while a short check at minimum speed shows everything as working. That is why we run the air conditioner in different modes and at different fan speeds — this way a hidden defect shows up before the equipment stops working for the owner again.
Tech Service works as a direct contractor: our own technician comes to you, not an intermediary who passes the request to a third party. Our specialist performs the free diagnostics, identifies the faulty unit, and carries out the work — from checking the inverter board to refilling the refrigerant circuit. When a direct contractor does the work, responsibility for the result and the parts is not blurred between subcontractors: the warranty is provided by the one who performed the tasks, and if the error returns, you need to contact one address instead of searching for who in the chain is responsible for the unit. Our technicians have 4 to 20 years of experience, so a request in the city is handled by someone who understands Hyundai inverter models, not a dispatcher hearing this brand for the first time.
We have gathered what determines the repair result: what diagnostics starts from, where the cause is most often hidden, and why prevention does not replace repair.
80brands
We work with air conditioners and split systems of every brand sold in Kazakhstan — from Almacom, Gree and Midea to LG, Samsung, Chigo and rare imported makes. Can’t find yours in the list? Call anyway — a technician will come and take a look.
Tech Service technicians repair other appliances too — with the same 1-year warranty on labour and parts.
Refrigerator Repair in Almatyfrom 3 000 ₸
Washing Machine Repair in Almatyfrom 3 000 ₸
Dishwasher Repair in Almatyfrom 3 500 ₸
Oven Repair in Almatyfrom 3 000 ₸
Cooktop Repair in Almatyfrom 3 500 ₸
Air Conditioner Repair in Almatyfrom 3 500 ₸
Boiler and Water Heater Repair in Almatyfrom 2 500 ₸
Freezer Repair in Almatyfrom 6 000 ₸
Tumble Dryer Repair in Almatyfrom 5 000 ₸
Coffee Machine Repair in Almatyfrom 2 500 ₸
Robot Vacuum Cleaner Repair in Almatyfrom 3 500 ₸
Vacuum Cleaner Repair in Almatyfrom 1 500 ₸
Microwave Oven Repair in Almatyfrom 2 000 ₸
Hair Dryer Repair in Almatyfrom 1 500 ₸
Iron Repair in Almatyfrom 3 000 ₸
Electric Kettle Repair in Almatyfrom 2 500 ₸
Mixer Repair in Almatyfrom 2 500 ₸
Multicooker Repair in Almatyfrom 500 ₸
Air conditioner errors are codes on the display or flashing indicators that show which component has failed.
5 March 2026 · 12 minutes read
If your air conditioner is leaking, first turn it off and cut the power, place a container under the drip, and move any wiring away from the water.
19 October 2025 · 12 minutes read
Gas boiler errors are codes on the display or a flashing indicator that point to a specific component: ignition, pressure, draft, sensor, or control board.
10 February 2026 · 11 minutes read












