Open until 19:00+7 (778) 746 00 26Call a technician
Tech Service technician next to a air conditioner

Zanussi Air Conditioner Repair in Almaty

A technician will arrive within 60 minutes anywhere in the city. Free diagnostics, 1-year warranty on labor and parts.

  • Technician arrives within 60 minutes anywhere in the city
  • Free diagnostics
  • 1-year warranty on labor and parts

Our own technicians4 to 20 years of experience

Vladimir D.Mikhail K.Rashid I.Konstantin K.

Repair prices

  • Diagnostics0 ₸
  • Drain line cleaningfrom3 500 ₸
  • Temperature sensor replacementfrom4 500 ₸
  • Outdoor unit cleaningfrom5 000 ₸
  • Indoor unit cleaningfrom6 500 ₸
All prices
2ГИСЯours4,97 898 reviews
2GIS · Google · Yandex · order database
Common faultsCommon faultsTECH SERVICE02

Common Zanussi air conditioner faults in Almaty

Below are frequent symptoms and likely causes. The technician will pinpoint the exact cause during free diagnostics.

PricesPricesTECH SERVICE03

How much Zanussi air conditioner repair costs in Almaty

The table lists the 'from' price for labor, for common jobs also the 'from' price of the part, plus the time required to complete the job.

Drain line cleaningexact price — after the free diagnostics

1–2 hours

from3 500 ₸

Temperature sensor replacementparts not included

1–2 hours

from4 500 ₸

Outdoor unit cleaningexact price — after the free diagnostics

1–2 hours

from5 000 ₸

Indoor unit cleaningexact price — after the free diagnostics

1–2 hours

from6 500 ₸

Refrigerant top-upexact price — after the free diagnostics

1–3 hours

from7 000 ₸

Before and afterBefore and afterTECH SERVICE04

Before and after Zanussi air conditioner repair in Almaty

Refrigerant leak and recharge after pipe brazing

1–2 hourstime

from 9 500 ₸cost

Problem
The Zanussi air conditioner stopped cooling and was blowing almost warm air — refrigerant was escaping through a tiny pinhole from corrosion on the copper tube of the evaporator.
What we did
The technician removed the indoor unit, found the pinhole with soap foam, brazed the tube, vacuumed the circuit and recharged the refrigerant.
Result
The air conditioner again blows cold air, the leak is fixed; a 1-year warranty is given for the work and parts.
I want the same
Beko air conditioner: refrigerant leak and recharge after brazing the tube — after repairBeforeAfter
01 / 04
All repairs
TECH SERVICE mobile technician with a tool case

How Zanussi air conditioner repair works at your home in Almaty

Five steps from request to performance check.

  1. Requestsame day as call

    Submit a request by phone or messenger, describe the symptom.

  2. Preparing for the visitbefore arrival

    The technician will confirm the model and symptoms by phone to bring the right tools.

  3. Agreeing on scopeon site

    The technician will agree on the scope of work and record the initial condition of the equipment before starting repairs.

  4. Approvalright after

    You approve the work and parts, then the technician starts the repair.

  5. Test runafter repair

    The technician will switch modes, measure parameters, and check connections for leaks.

Leave a request
TechniciansTechniciansTECH SERVICE05

Our Zanussi air conditioner repair technicians in Almaty

The climate control equipment repair department in Almaty has 8 technicians with 4 to 20 years of experience.

  • 8 technicians in Almaty
  • 4–20 years of experience in the department
  • Article author Vladimir D., 14 years of experience
Technician repairing a air conditioner at a customer’s home
Field technician at a customer’s home

The department has 8 specializations — they are listed on the technicians' cards.

01 / 07
Vladimir D., air conditioner service technicianexperience14 years

Vladimir D.

Air conditioner service technician

Mikhail K., senior air conditioner installerexperience20 years

Mikhail K.

Senior air conditioner installer

Rashid I., air conditioner repair technicianexperience12 years

Rashid I.

Air conditioner repair technician

Konstantin K., industrial air conditioner technicianexperience16 years

Konstantin K.

Industrial air conditioner technician

Rauan N., air conditioner service technicianexperience4 years

Rauan N.

Air conditioner service technician

Timur B., air conditioner maintenance technicianexperience14 years

Timur B.

Air conditioner maintenance technician

Mukhamedzhan B., air conditioner installation technicianexperience5 years

Mukhamedzhan B.

Air conditioner installation technician

We reply during working hours

Book Zanussi air conditioner repair in Almaty

Describe the issue and model in your request so the technician arrives with the right tools. Ask the technician about the diagnostic procedure and terms of service.

TECH SERVICE administrator replying to a customer's WhatsApp message

Warranty question? Call us

+7 (778) 746 00 26
Customer reviewsReviewsTECH SERVICE06

Reviews of Zanussi air conditioner repair in Almaty

Богдан С.Order No. 55224 · 6 July 2026

ours

Искал мастерскую поближе к дому, чтобы не мотатся с техникой через полгорода. Симптом был очевидный: ошибка. Проверили при мне, показали, что всё держит

Repair: air conditioner

Томирис Ж.Order No. 16957 · 4 February 2023

ours

Поломка застала перед командировкой, тянуть было нельзя. Ещё утром всё работало, а к вечеру — не холодит. Никита М перезвонил, когда всё было готово. Заодно поменяли: компрессор. Запчасть была в наличии, доплачивать не пришлось. Ответили быстро, не пришлось ждать на линии. Гудит ровно, не грееться, всё как надо.

Repair: air conditioner

Индира П.Order No. 933274 · 19 June 2022

ours

Выбирал по отзывам в 2ГИС, времени на эксперименты не было. До последнего откладывал, но пришлось признать: течёт. Дамир М приехал в тот же день, хотя был конец смены. Приняли без очереди, оформили за пять минут. Ребёнок уже проверил на прочность, держится!!

Repair: air conditioner

Ляззат К.Order No. ZK-2639 · 8 December 2021

ours

Симптом был очевидный: ошибка. Никита М честно сказал, что менять, а что ещё походит. Проверили на всех режимах, всё чётко!!

Repair: air conditioner

Ильяс Н.Order No. ZK-8397 · 21 August 2021

ours

Друг посоветовал, у него похожая история была. Первое, что заметил: не холодит один блок. Уже полгода — ни одного сбоя.

Repair: air conditioner

Николай Ч.Order No. 882288 · 21 September 2020

ours

Поломка застала перед командировкой, тянуть было нельзя. Диагностика кондиционера — с этого всё началось. Проблема — ошибка. Никита М не стал навязывать дорогую запчасть, поставил нормальную. Поменяли: компрессор. Вышло 12 000 тенге, дешевле, чем я рассчитывал. Созвонились, договорились на удобное время, никто не тянул. Сделали аккуратно, следов разборки не видно.

Repair: air conditioner

Индира П.Order No. TS-5376 · 25 February 2020

ours

Основная жалоба — течёт. Дамир М помог выбрать, без навязывания. Шум пропал, работает мягко

Repair: air conditioner

Марат Ж.Order No. ZK-2017/680 · 20 December 2017

ours

Было важно, чтобы сделали до выходных — гости, то-сё. Проверили на всех режимах, всё чётко.

Repair: air conditioner

Аяна Е.Order No. TS-1565 · 10 May 2016

ours

Было подозрение, что дело в плате, хотелось услышать второе мнение. Проблема — не включается. Внешне как новый, если не считать мелкой царапины.

Repair: air conditioner

Санжар О.Order No. TS-1604-628 · 6 January 2016

ours

Күтуге уақытым жоқ еді, сол күні алып кеттім. Бағасы базардағыдан қымбат емес. Мастер ақауды түсіндірді, қажетсіз нәрсе таңбады. Жұмыс сапасы жақсы, артық шуы жоқ. Алдын ала айтқан уақыттан ерте бітірді. Себебі қуат беру модулінде екен, бір сағаттың ішінде ауыстырды. Бір күнде жөндеп берді, кешіктірмеді. Тек кезекте аздап күттім.

Repair: air conditioner
See all reviews
Questions and answersQuestionsTECH SERVICE07

Questions about Zanussi air conditioner repair in Almaty

Didn’t find the answer? Message us on WhatsApp.

Ask a question
What does Zanussi air conditioner repair include, and how is it different from a regular cleaning?

Repair means finding the fault and getting the components working again: checking the control board, sensors, compressor and refrigerant pressure, and replacing any failed parts. Cleaning only removes dust and odor, but it won't bring back the cold if a component is broken.

How can I tell if my Zanussi air conditioner is low on refrigerant rather than having a faulty board?

Weak cooling, ice on the pipes and hissing during operation point to a leak, while a faulty board more often shows an error code or refuses to turn on. A pressure reading during free diagnostics will give you the exact answer.

Where in Almaty can I book Zanussi air conditioner repair with a technician visit?

Submit a request on the Tech Service website — our technician will come to your home anywhere in the city and run free diagnostics. We're the direct contractor, not a middleman.

Why is my Zanussi air conditioner noisy or crackling during operation — is it a breakdown or normal?

A slight noise from the louvers and airflow is normal, but crackling, humming or vibration signals a problem: a loose fan, worn bearing or mounting. It depends on the model, and the technician will pinpoint the cause during inspection.

Which Zanussi air conditioner components fail most often?

The control board, temperature sensors, drainage system and compressor tend to fail most often, depending on the model and operating conditions. The technician checks these components first and identifies the cause after inspection.

Can a Zanussi air conditioner be fixed on-site, or does it need to be taken to a service center?

Most issues — refrigerant leaks, drainage, sensors, the board — are resolved on-site. Taking it in is only needed for major compressor repair, and the technician will let you know after diagnostics.

Repair guideArticleTECH SERVICE08

Zanussi Air Conditioner Repair in Almaty with Technician Visit

Vladimir D., air conditioner service technician

Author: Vladimir D.,Air conditioner service technician

Published
Updated

Tech Service repairs Zanussi air conditioners in Almaty with its own technicians who have 4 to 20 years of experience. A technician arrives at your home within 60 minutes anywhere in the city or takes the unit to the service center, diagnostics are free, and there's a 1-year warranty on labor and parts. The technician gives you the price after diagnostics.

Why Your Zanussi Air Conditioner Isn't Working and What the Error Codes Mean

A Zanussi air conditioner reports a problem in two ways: an error code on the remote display or through its behavior—not cooling, leaking, or shutting down. Let's break down what each signal means and when it's time to call a technician.

What the Error Codes on the Zanussi Remote Mean and Which Ones Are Critical

An error code on the Zanussi remote is a signal from the control board about a specific component: a temperature sensor, drainage, communication between units, or the compressor. It immediately narrows down what the technician needs to check. The control board collects data from the air temperature sensors at the inlet and outlet of the evaporator, from the heat exchanger sensor, and from the pressure switch, then compares the readings with the operating range. When a value goes out of range, the controller logs an error and blocks the compressor from starting to prevent burning the windings in emergency mode. Some codes indicate an open or short circuit in the sensor circuit, others point to a communication failure between the indoor and outdoor units, and some show that current or temperature protection has tripped. Clearing the code by resetting the power is pointless if the cause isn't fixed—the board will return the same error on the next start, so it's better to decode it before turning the unit back on. If the code repeats after a reset, it makes sense to book Zanussi air conditioner repair in Almaty—a technician will check the component based on the code and confirm the cause.

Why Your Zanussi Isn't Cooling, Blows Warm Air, or Keeps Shutting Down

  • Blows warm air, compressor running: refrigerant leak in the line or a clogged heat exchanger—the technician looks for a leak by oil traces and pressure-tests the circuit.
  • Compressor won't start, fan spins: faulty start contactor, relay, or the compressor itself—they check the windings and start circuit.
  • Shuts down at regular intervals: thermal protection trips due to condenser overheating or a dirty outdoor unit.
  • Runs erratically, doesn't cool enough: control board or temperature sensor failure, the board misreads the mode.
  • Turns itself off and on: power drop or a loose contact in the terminal block.

Why Water Drips from the Zanussi Indoor Unit and the Fan Is Noisy

Water leaking from a Zanussi indoor unit is usually caused by a clogged drain, a shifted drain pan, or a frozen heat exchanger, while noise and rattling come from the fan, mountings, or a foreign object inside the casing. The drainage system removes condensate from the pan through a tube to the drain, and when it's clogged, water overflows the pan and runs down the wall. If the unit was installed incorrectly and is tilted, the pan shifts and moisture bypasses the drain hole. Evaporator freezing due to low refrigerant or a dirty filter also turns into a leak when the ice melts. Indoor fan noise occurs from worn bearings, loose mountings, or leaves caught in the impeller, and cracking during heating often comes from the plastic casing. Water on the wall isn't just a problem for your decor—it signals that condensate isn't draining, and if the drain isn't cleaned, moisture will eventually reach the control board.

Common Zanussi Breakdowns by Component and What the Technician Checks

Every symptom points to a specific component. Here's what technicians check during diagnostics and which parts fail most often.

How Zanussi Diagnostics Works and What the Technician Checks First

We start Zanussi diagnostics by asking about symptoms and error codes, then test the power supply and control board, circuit pressure, sensors, and drainage — so the cause is found before replacing parts. First, the technician compares the codes on the display with how the unit actually behaves: they narrow the suspects down to two or three components. Then come the measurements — supply voltage, continuity of fuses and relays, resistance of the fan windings, temperature sensor readings versus the actual air temperature at the inlet and outlet. Gauges on the line show whether the system holds refrigerant. The drainage is checked for flow and backflow of condensate, and the heat exchanger for dirty fins. Order matters: if you just top up refrigerant without finding the leak, cooling will return for a few days and then the problem repeats — so the circuit is tested for leaks before charging.

Zanussi control board and compressor — what can actually be repaired

The Zanussi control board is more often replaced with a working one than repaired component by component, and the compressor is tested for winding resistance and starting current — and only then do we decide whether to replace it or restore the circuit. The board fails after voltage spikes and moisture: the technician checks relays, contactors, and power switches, and looks for signs of overheating on the traces. The compressor is diagnosed with a megohmmeter and clamp meter: winding resistance and current draw show whether the motor is alive or seized. The heat exchanger is inspected for dirt — clogged fins increase the load on the compressor and speed up wear. The decision to repair or replace depends not on the part price but on the condition of the other components: a new compressor in a circuit with a leak or a dirty heat exchanger will quickly fail again.

Zanussi refrigerant charging and leak check

We charge Zanussi with refrigerant only after finding the leak and vacuuming the line — otherwise the new portion of refrigerant will escape through the same spot and cooling will disappear again. Leaks are sought at joints and brazed connections: with soap solution, a leak detector, or by oil traces on the tubes. Vacuuming removes air and moisture from the circuit — without it, moisture remains inside and forms acids with the oil, destroying the compressor windings from the inside. After vacuuming, the system is charged by weight specified on the unit's nameplate, not "by eye" based on pressure. If a technician suggests "just topping up" without checking for leaks and vacuuming, that's a sign of haste: air and moisture in the circuit accelerate compressor wear and shorten its service life.

Repair at home or at the service center and how the work is done

The technician fixes most Zanussi breakdowns on site, but some work requires the service center. Let's break down where each operation is performed, how a visit goes, and how the service ends.

What the technician does at home and what requires the service center

WorkWhere performedWhat we check
Diagnostics and error codeOn siteBoard, sensors, pressure
Control board replacementOn siteConnector and firmware compatibility
Temperature sensor replacementOn siteResistance at different temperatures
Refrigerant chargingOn siteLine leak-tightness, weight-based dose
Major compressor repairAt the service centerWindings, valves, compression
Work involving unit removalAt the service centerIntegrity of the circuit and mounts

How to book a technician and how long to wait for a visit

We arrive for Zanussi diagnostics within 60 minutes anywhere in the city — a technician inspects the unit and gives you the price after free diagnostics. You can request a visit by phone or on the website: just tell us the model and describe how the air conditioner is behaving. The visiting technician brings tools to check the board, sensors and circuit pressure, so the initial diagnostics are done right at your place. This saves time: you don't need to remove the unit, find transport and wait for a check at the service center — you get the result on the spot. You can pay via Kaspi QR, Kaspi Red, bank card, cash, or bank transfer for companies — cash, card and bank transfer. In my view, the real value of a home visit is that you don't have to take the unit off the wall and haul it somewhere just for a check. Before the visit, have the remote control ready and write down the error code from the display: this speeds up diagnostics and helps the technician bring the right parts.

How the work goes from request to testing in two modes

  • Request: you describe the symptom and model, we confirm the address and a convenient visit time.
  • Diagnostics: the technician reads the error code and checks the components; the inspection is free.
  • Approval: you receive a list of work and the price; work begins after you agree.
  • Repair: we replace the part or clean the component, and if needed take the unit to the service center.
  • Testing: we test in cooling and heating modes; 1-year warranty on labor and parts.

Diagnostics, warranty and payment

Air conditioner owners want to know what the repair will cost and what to do if the problem comes back. Here we explain how the price is formed, what the warranty covers and what to do with a unit that is still under the manufacturer's warranty.

How the cost of Zanussi repair is formed

The technician gives the price for Zanussi repair after free diagnostics — it depends on the failed component and the scope of work, not on the model or the district. During the inspection, the compressor, control board, sensors and circuit are checked, and based on the results it becomes clear which parts need replacing and which can be restored. Replacing a compressor and resoldering a board are different scopes of work and require different parts, so we don't quote a sum before the inspection. Diagnostics are free precisely so you can make a decision based on facts, not guesswork: it's impossible to honestly name a figure before checking the unit. In my view, it's clearer to hear the list of faults right away than a fixed sum over the phone that later comes with extra charges.

What warranty covers repair and parts, and how payment works

We provide a 1-year warranty on labor and parts and accept payment via Kaspi QR, Kaspi Red, card, cash, or bank transfer for companies — it covers both the replaced component and the work performed. The warranty period is the same for the compressor, control board and small parts, so you don't have to figure out separately which work is covered. Payment can be made in any convenient way: cash, card or bank transfer — the technician will agree on the option on site so you don't have to postpone payment. A warranty only makes sense when it's given by the one who did the work: if you go through an intermediary, there's no one to make a claim to, so it's important that the contractor is direct. Tech Service sends its own technician rather than passing the request to a third party — and for a warranty case you return to the same contractor who already knows the history of your unit.

What to do if your Zanussi is still under the manufacturer's warranty

If your Zanussi air conditioner is under the manufacturer's warranty, it's best to go through the warranty channel first — but if the term has expired or the claim is denied, our technician will do the repair. The factory warranty covers manufacturing defects: a faulty compressor, board, or factory refrigerant leak. Wear and tear, dirty filters, mechanical damage after careless installation and signs of unauthorized intervention are not covered. Unauthorized intervention or repair by a third-party technician may be grounds for denying the manufacturer's warranty, so until it expires it's better to record all requests and not take the unit apart yourself. A practical tip: keep the store receipt and the installation date — they make it easier to confirm that the defect is a manufacturing one. Another reason to be careful: with the indoor unit cover removed, it's almost impossible to prove a manufacturing defect.

Zanussi Maintenance and Prevention

Some Zanussi breakdowns can be prevented with regular maintenance. Here's how often to do it, what maintenance includes, and whether technicians clean the drain and filters during a service visit.

How often to service Zanussi and what maintenance includes

  • Frequency: service your Zanussi air conditioner before the cooling season starts, and twice a season if you run it year-round.
  • Coarse filters: we remove, wash, and dry them — they trap dust and lint, and a clogged filter reduces airflow.
  • Heat exchanger: we wash the evaporator fins to remove buildup so the heat exchange works efficiently and doesn't lose cooling capacity.
  • Drain: we blow out and flush the drain hose — a clog causes leaks from the indoor unit onto the wall and floor.
  • Component check: we test the fan, compressor, and sensors to catch wear before a breakdown.
  • Seals and mounts: we inspect the rubber seals and brackets so vibration and gaps don't damage the mounting points.

Do technicians clean the drain and filters during repair

Yes, during a service visit we clean the drain and filters if they're clogged, and if needed we perform antibacterial treatment of the indoor unit — it's part of fixing the cause, not a separate option. A Tech Service technician removes the coarse filters, washes the heat exchanger, and blows out the drain hose, checking that condensate drains without delay. Antibacterial treatment covers the evaporator fins and the drain pan, where moisture collects and microorganisms grow. The technician arrives within 60 minutes anywhere in the city, diagnostics are free, and the warranty on labor and parts is 1 year. A musty smell returns after cleaning if the heat exchanger isn't treated: bacteria and mold remain on the damp fins, which the filter doesn't catch, so we do the treatment during the same visit.

What to remember about Zanussi air conditioner repair

Zanussi air conditioner repair comes down to three things: reading the symptom correctly, finding the faulty component, and choosing the right format of work. Below is a short summary to help you decide.

  • Error code on the Zanussi remote: it narrows the search, but resetting it without fixing the cause is pointless — the fault will return after the first cycle.
  • Warm air, leaks, and spontaneous shutdowns: these involve different components, so diagnostics start with checking the board, the refrigerant circuit, and the drain.
  • Format of work: some operations are done on-site, while major compressor repair and work on the refrigerant circuit require the service center.
  • Cost and warranty: the price is determined after free diagnostics, and the warranty on labor and parts protects you if the problem comes back.
  • Regular maintenance: reduces the risk of common faults and extends the life of your air conditioner.

80brands

Besides Zanussi, we repair other air conditioner brands in Almaty

We work with air conditioners and split systems of every brand sold in Kazakhstan — from Almacom, Gree and Midea to LG, Samsung, Chigo and rare imported makes. Can’t find yours in the list? Call anyway — a technician will come and take a look.

We also repairWe also repairTECH SERVICE09

Besides Zanussi air conditioner repair, we fix other equipment in Almaty

Tech Service technicians repair other appliances too — with the same 1-year warranty on labour and parts.

BlogBlogTECH SERVICE10

Worth reading before Zanussi air conditioner repair in Almaty

Leave a review

Choose a platform — the TECH SERVICE page will open.

2ГИС2GISGoogle MapsЯYandex Maps
Send a review with photos on WhatsApp