experience14 yearsVladimir D.
Air conditioner service technician
City
Language
What broke
Sections
Message on WhatsApp+7 (778) 746 00 26Mon–Fri 10:00–19:00, Sat–Sun 11:00–18:00
Not cooling in the heat? We'll be there within 60 minutes anywhere in the city.
Our own technicians4 to 20 years of experience




Repair prices
Each symptom points to a specific component: below is what we check for no cooling, leaks, noise, and other signs.
Filter, refrigerant leak, compressor
from9 500 ₸
Clogged drain, misaligned pan
from3 500 ₸
Remote or batteries, circuit breaker, board
from10 000 ₸
The code points to a specific component
from10 000 ₸
Fan, mounting, compressor
from8 500 ₸
Dirty heat exchanger, low refrigerant
from7 000 ₸
Compressor overheating, sensor, board
from4 500 ₸
Batteries, receiver, board
from10 000 ₸
The table lists the 'from' price for labor, for common jobs also the 'from' price of the part, plus the time required to complete the job.
1–2 hourstime
from 9 500 ₸cost

BeforeAfter5 steps

Five steps from call to performance check.
Your request is logged and passed to a technician with the right profile.
The technician agrees on a convenient time and the scope of work.
Diagnostics are free; the technician identifies the cause and gives the price.
Work is carried out after the scope and price are approved.
The technician starts the air conditioner, measures the output temperature, and checks for leaks.
The climate control equipment repair department in Almaty has 8 technicians with 4 to 20 years of experience.

The department has 8 specializations — they are listed on the technicians' cards.
experience14 yearsAir conditioner service technician
experience20 yearsSenior air conditioner installer
experience12 yearsAir conditioner repair technician
experience16 yearsIndustrial air conditioner technician
experience4 yearsAir conditioner service technician
experience14 yearsAir conditioner maintenance technician
experience5 yearsAir conditioner installation technician
We reply during working hours
Leave a request — when we call, please specify the symptom, air conditioner model, and address so the technician can bring the right tools and parts.

Warranty question? Call us
+7 (778) 746 00 267 898 reviews of repairs at TECH SERVICE in total
Владимир Н.Order No. 71685 · 30 August 2025
oursДо этого обращался в другой сервис, там только развели руками. После выходных обнаружил: шумит. Ни копейки сверху, как и обещали. Из деталей — плата. Мастер сразу сказал, что к чему, без размытых формулировок. Проверил дома — всё на месте, ничего не забыли
Фарида К.Order No. ZK-2021/740 · 4 May 2021
oursНужен был счёт и чек, у нас техника на балансе организации. Жалоба простая: не включается. Пользуюсь ежедневно, вопросов нет.
Динара М.Order No. ZK-9415 · 1 February 2021
oursХотел сначала вызвать мастера на дом, потом передумал. Основная жалоба — течёт. Сделали и забыл про проблему
Николай Ч.Order No. 882288 · 21 September 2020
oursПоломка застала перед командировкой, тянуть было нельзя. Диагностика кондиционера — с этого всё началось. Проблема — ошибка. Никита М не стал навязывать дорогую запчасть, поставил нормальную. Поменяли: компрессор. Вышло 12 000 тенге, дешевле, чем я рассчитывал. Созвонились, договорились на удобное время, никто не тянул. Сделали аккуратно, следов разборки не видно.
Гульмира С.Order No. TS-2001-181 · 13 January 2020
oursБыло подозрение, что дело в плате, хотелось услышать второе мнение. Больше всего напрягало: не холодит. Починили и дали гарантию на месяц.
Куаныш Б.Order No. TS-6861 · 13 April 2018
oursҚұрылғы ескі болғандықтан, бөлшек табыла ма деп қорықтым. Бірнеше жерге қоңырау шалдым, осында ғана нақты айтты. Мастер жарты сағатқа кешікті, бірақ қоңырау шалды)
Ержан А.Order No. 2017-9995 · 12 July 2017
oursПриехал из командировки, а дома — течёт. Приняли, выдали квитанцию, всё по-человечески. Включил, проверил, работает
Юлия А.Order No. TS-1610-389 · 1 February 2016
oursДруг посоветовал, у него похожая история была. Привёз на диагностику: мультисплит-система. Первое, что заметил: ошибка. Посмотрели, назвали срок — два дня. Под замену пошло: плата. Цену обсудили до начала, сюрпризов не было. Однозначно да. Гудит ровно, не грееться, всё как надо.
Фарида К.Order No. ZK-2016/289 · 31 January 2016
oursНикита М принял, посмотрел и сразу сказал, что делать. Сказали 12 000, я согласился без торга. Крутит ровно, без рывков.
Санжар О.Order No. TS-1604-628 · 6 January 2016
oursКүтуге уақытым жоқ еді, сол күні алып кеттім. Бағасы базардағыдан қымбат емес. Мастер ақауды түсіндірді, қажетсіз нәрсе таңбады. Жұмыс сапасы жақсы, артық шуы жоқ. Алдын ала айтқан уақыттан ерте бітірді. Себебі қуат беру модулінде екен, бір сағаттың ішінде ауыстырды. Бір күнде жөндеп берді, кешіктірмеді. Тек кезекте аздап күттім.
Didn’t find the answer? Message us on WhatsApp.
Ask a questionTake a look at Beko's entry-level split systems — they cost less than inverter models. A standard model is enough for a small room, and the technician can give you a more precise recommendation during diagnostics.
The final price depends on the model and how complex the installation is: the length of the line, the floor, and the wall type. The technician gives you an exact quote after a free on-site diagnostic.
At Tech Service: we're the direct contractor, and a technician comes to your home anywhere in the city within 60 minutes. No middlemen, so the same specialist who ran the diagnostics does the repair.
The technician fixes most issues on-site — refrigerant leaks, dirt buildup, a faulty board or fan. Only certain components, like the compressor, are taken to the service center when the repair requires special conditions.
Rinse the indoor unit filters every two to four weeks, and book a professional cleaning of the heat exchanger and drain once a year. This keeps the cooling efficient and lowers the risk of breakdowns.
The refrigerant may have leaked out, the filter may be clogged, or the compressor may have failed. It depends on the model, but a free at-home diagnostic will pinpoint the exact cause.
Tech Service repairs Beko air conditioners in Almaty with its own technicians, who have 4 to 20 years of experience. A technician arrives at your home within 60 minutes anywhere in the city or takes the equipment to the service center, diagnostics are free, and there's a 1-year warranty on labor and parts. The technician quotes the price after diagnostics.
Beko air conditioners show similar symptoms, but the causes behind them vary. Let's look at what most often lies behind each complaint and when you can't do without a technician.
Most often, "won't cool" on a Beko means a refrigerant leak, clogged filters, or a faulty temperature sensor, and we check these three components first during free diagnostics. The technician measures pressure in the refrigerant line, inspects the air filters, and compares temperature sensor readings with the unit's actual operating mode. A leak in the circuit develops gradually: refrigerant escapes through microcracks in the brazing, and for the first few weeks the unit still blows cold, then cooling weakens, the compressor runs longer, and eventually goes into protection mode. Clogged filters produce a similar picture without any refrigerant loss—air simply doesn't pass through the heat exchanger, and heat exchange is disrupted. A sensor fault throws off the cycle: the board receives incorrect room temperature data and shuts off the compressor prematurely. If the outdoor unit runs nonstop while the indoor unit blows warm air, don't delay calling a technician—the compressor is wearing out, and the risk of replacement grows.
Water from a Beko indoor unit almost always means a clogged drain system or a displaced drain hose, and we clear the drain on-site. Condensate flows from the heat exchanger into the pan and out through the hose; when dust, lint, and slime accumulate inside, water overflows and drips into the room. A displaced, cracked, or disconnected hose causes the same leak even with a clean drain, so the technician first checks flow, then the hose connection. A second source is heat exchanger freezing: with low refrigerant or dirty filters, ice melts and fills the pan faster than the drain can carry it away. If it drips constantly, not just in hot weather, check the unit's tilt angle too—a misalignment causes leaks even with a clean drain, and then cleaning only helps temporarily.
The code on a Beko display narrows the search to the specific component where protection tripped. Below is how to read typical codes, what circuits they point to, and what to do before the technician arrives.
The code on a Beko display is an alphanumeric designation that points to the component where protection tripped, not to a specific broken part. The control board detects a deviation from normal operation in temperature sensors, the compressor, or the fan and displays the code, and on some series an indicator on the indoor unit blinks instead of showing digits. The same code on different split-system lines may refer to different circuits, so the interpretation is checked against the service documentation for the specific model, not a universal table from the internet. Two characters are usually related to sensors, three—to compressor protection or data exchange between units. Write down the code and when it appeared (at startup, in hot weather, after a power outage)—this detail saves diagnostic time.
| Code group | What it indicates | What we check |
|---|---|---|
| Temperature sensor | open or shorted sensor | sensor circuit and connector |
| Compressor protection | overheating or overload | current, circuit pressure |
| Fan | stopped or motor fault | winding and bearings |
| Unit communication | data exchange failure | board and wiring |
| Drainage | pan overflow | drain and float switch |
Beko air conditioner repair in Almaty follows one procedure — from request to post-repair check. We'll walk you through each step so you know what's happening and what you're paying for.
After you request service, our technician arrives at your home within 60 minutes anywhere in the city, or if it's more convenient, picks up the unit for repair at our service center. You can request service by phone or in a message: we'll confirm the address, the indoor and outdoor unit models, and how the fault shows up. Then the engineer prepares tools for the specific task — from checking the circuit to inspecting the electricals. If the split system is on a balcony or under the ceiling, we discuss access to the outdoor unit in advance so the technician can plan the work on site. When requesting service, tell us the model and BTU — the technician will bring the right tools and won't waste the visit on clarifications. If the unit no longer starts, let us know in advance: the engineer will take that into account when preparing for the visit.
Diagnostics are free: the technician checks circuit pressure, electrical circuits and sensors, finds the cause, and only then quotes the cost of work. First, he listens to how the compressor behaves at startup and compares the readings with the error code if it's shown on the display. Then he checks the refrigerant pressure at both ports, tests the control board and temperature sensors, and inspects the drainage and contacts. Based on the results, the engineer explains what exactly failed — a leak, a start capacitor, a clogged capillary tube, or a board fault — and what work is needed. He quotes the price after diagnostics: that way you pay for fixing the cause, not for a list of replacements. If the cause requires parts, the technician first explains which component is being replaced and why the repair won't work without it.
After the work, the technician starts the Beko air conditioner in all modes and checks the result, and there is a 1-year warranty on labor and parts. He measures the air temperature at the indoor unit outlet, listens to the compressor under load, and makes sure the control board handles cooling and heating modes without faults. If the compressor or start relay was replaced, the check takes longer: it's important to catch the moment it reaches operating mode and make sure the circuit pressure stays stable. The technician also checks the drainage separately — if it's clogged, water will run down the wall again even if cooling is back. It's worth testing the result at the outdoor temperature when the fault appeared — otherwise you might miss the issue.
Beko air conditioner service in Almaty depends on the type of equipment: an inverter split system and a conventional model fail differently, and their diagnostics focus on different components.
We service Beko wall-mounted split systems of various capacities — from household 9000 BTU units to 18000 and 24000 BTU models. In household wall units, the drain, indoor unit fan, and starting automation are the most common trouble spots, while in high-capacity models the load falls on the compressor and refrigerant lines. Models rated 9000–12000 BTU are usually installed in bedrooms and small rooms, 18000 BTU in living rooms, and 24000 BTU in spacious halls and small offices, and the room volume determines how long the unit runs without cycling off. Higher-capacity models put more load on the compressor, so when a unit "doesn't cool," we first check the circuit pressure rather than just cleaning the filters. We repair Beko air conditioners in Almaty with these capacity and unit-type specifics in mind.
In Beko inverter air conditioners, the control board plays the key role, regulating the compressor speed, so diagnostics start with the electronics. We check the module's power supply, the integrity of the temperature sensors, and the output signals from the board, and only then assess the compressor itself and the circuit pressure. A conventional model with an on/off compressor is simpler: there, the starting relay, capacitor, or a clogged drain is more often to blame, and the fault is easier to spot. Inverter units are more sensitive to voltage spikes and board overheating, so diagnostics take longer and require checking each sensor individually. The compressor doesn't like frequent on-off cycling when the board malfunctions — delaying electronics repair is risky for the compressor itself.
Warranty and a direct contractor are the two questions that most often decide who to trust with Beko air conditioner service. Let's break down exactly what our one-year warranty covers and how a direct contractor differs from a subcontractor through an aggregator.
We provide a 1-year warranty on labor and parts, meaning we stand behind both the quality of the work and the parts installed. Our technicians have 4 to 20 years of experience, so they know which components of this brand fail most often and what to look for on a repeat visit. The warranty year covers both parts: the work performed and the parts installed. Diagnostics before work begins is free with us, so checking a component adds no cost. The parts warranty matters no less than the labor warranty: it also covers the installed parts. If a component fails again after repair, the repeat visit and inspection are included in the same warranty year and are not charged separately.
Tech Service is a direct contractor: our own specialist comes to you, not a subcontractor through an aggregator, so we stand behind the work and the warranty. We can be at your door anywhere in the city within 60 minutes, and the person who arrives is the one who sees the job through to the end—not a random contractor from a middleman platform. You can pay via Kaspi QR, Kaspi Red, bank card, cash or bank transfer for companies, and the price is quoted after free diagnostics, once the cause is clear. With this setup, there's no extra link between the owner and the contractor to pass complaints through. A middleman between you and the contractor adds an extra link where complaints get shifted. That's why the warranty is provided by the one who did the work. When a technician comes from a direct contractor, they have no reason to shift responsibility to a third party—they answer for the result to the owner of the appliance themselves.
The decision between repair and replacement depends on the component: the control board, fan, and drainage are usually restored, but replacing the compressor on an old unit isn't always worth it. The control board can be restored more often than you'd think—one failed module doesn't mean the whole unit needs replacing. The indoor and outdoor fan are replaced or restored based on the condition of the bearings and winding, and a clogged drain is cleared by cleaning without replacing parts. The compressor is the most expensive component of a split system: on equipment with a long service life, replacing it can cost as much as a new unit, so the remaining resource is assessed here. If a specialist suggests replacement, ask them to explain which component has worn out—this helps you compare options without pressure.
We've gathered the key points that affect the outcome of restoring your Beko air conditioner—from how accurately you describe the symptom to who stands behind the warranty and parts after the work.
80brands
We work with air conditioners and split systems of every brand sold in Kazakhstan — from Almacom, Gree and Midea to LG, Samsung, Chigo and rare imported makes. Can’t find yours in the list? Call anyway — a technician will come and take a look.
Tech Service technicians repair other appliances too — with the same 1-year warranty on labour and parts.
Refrigerator Repair in Almatyfrom 3 000 ₸
Washing Machine Repair in Almatyfrom 3 000 ₸
Dishwasher Repair in Almatyfrom 3 500 ₸
Oven Repair in Almatyfrom 3 000 ₸
Cooktop Repair in Almatyfrom 3 500 ₸
Air Conditioner Repair in Almatyfrom 3 500 ₸
Boiler and Water Heater Repair in Almatyfrom 2 500 ₸
Freezer Repair in Almatyfrom 6 000 ₸
Tumble Dryer Repair in Almatyfrom 5 000 ₸
Coffee Machine Repair in Almatyfrom 2 500 ₸
Robot Vacuum Cleaner Repair in Almatyfrom 3 500 ₸
Vacuum Cleaner Repair in Almatyfrom 1 500 ₸
Microwave Oven Repair in Almatyfrom 2 000 ₸
Hair Dryer Repair in Almatyfrom 1 500 ₸
Iron Repair in Almatyfrom 3 000 ₸
Electric Kettle Repair in Almatyfrom 2 500 ₸
Mixer Repair in Almatyfrom 2 500 ₸
Multicooker Repair in Almatyfrom 500 ₸
Air conditioner errors are codes on the display or flashing indicators that show which component has failed.
5 March 2026 · 12 minutes read
If your air conditioner is leaking, first turn it off and cut the power, place a container under the drip, and move any wiring away from the water.
19 October 2025 · 12 minutes read
Gas boiler errors are codes on the display or a flashing indicator that point to a specific component: ignition, pressure, draft, sensor, or control board.
10 February 2026 · 11 minutes read












