experience14 yearsVladimir D.
Air conditioner service technician
City
Language
What broke
Sections
Message on WhatsApp+7 (778) 746 00 26Mon–Fri 10:00–19:00, Sat–Sun 11:00–18:00
A technician arrives within 60 minutes anywhere in the city. Free diagnostics, 1-year warranty on labor and parts.
Our own technicians4 to 20 years of experience




Repair prices
The symptoms that come up most often and their likely causes. The technician will pinpoint the exact cause after diagnostics.
no power, faulty board, remote control
from10 000 ₸
refrigerant leak, compressor wear, filter
from9 500 ₸
clogged drain, freezing, installation
from3 500 ₸
fan wear, loose mounting
from8 500 ₸
the code points to a specific component
from10 000 ₸
dirty filter, condensation in the drain
from3 500 ₸
dead batteries, faulty receiver
from10 000 ₸
compressor overheating, board failure
from10 000 ₸
The table lists the 'from' price for labor, for common jobs also the 'from' price of the part, plus the time required to complete the job.
1–2 hourstime
from 9 500 ₸cost

BeforeAfter5 steps

Five steps from request to checking the unit after repair.
Submit a request in any convenient way, describe the symptom and your air conditioner model.
The technician arrives anywhere in the city within 60 minutes after the request is confirmed.
The technician checks the unit model, error code, and access to the outdoor unit before starting work.
We agree on the scope of work and cost before any intervention, then the technician starts the repair.
The technician checks the air conditioner operation. 1-year warranty on labor and parts.
The climate control equipment repair department in Almaty has 8 technicians with 4 to 20 years of experience.

The department has 8 specializations — they are listed on the technicians' cards.
experience14 yearsAir conditioner service technician
experience20 yearsSenior air conditioner installer
experience12 yearsAir conditioner repair technician
experience16 yearsIndustrial air conditioner technician
experience4 yearsAir conditioner service technician
experience14 yearsAir conditioner maintenance technician
experience5 yearsAir conditioner installation technician
We reply during working hours
Decide on a convenient visit time and who will be home, and find out where the indoor unit is installed. This helps the technician plan the work without unnecessary delays.

Warranty question? Call us
+7 (778) 746 00 267 898 reviews of repairs at TECH SERVICE in total
Елена К.Order No. 469762 · 11 September 2026
oursСмотрел, у кого есть запчасти на такую модель. Позвонил, описал проблему, сказали привозить — посмотрят в тот же день. Проверил дома — всё на месте, ничего не забыли.
Сауле Н.Order No. ZK-2025/192 · 11 December 2025
oursСмотрел, у кого есть запчасти на такую модель. Не люблю сервисы, но этот запомнил. Первое, что заметил: не холодит. Позвонил, описал проблему, сказали привозить — посмотрят в тот же день. В списке работ — дренаж. Сравнивал с двумя другими — здесь вышло ровнее всех. Крутит ровно, без рывков.
Даулет С.Order No. ZK-5804 · 21 September 2025
oursВыбирал по отзывам в 2ГИС, времени на эксперименты не было. Вечером включил — и всё стало ясно: течёт. Никита М возился с этим дольше, чем планировал, но довёл до конца. Сравнивал с двумя другими — здесь вышло ровнее всех. Всё оформили по договору, с печатью. Гудит ровно, не грееться, всё как надо.
Дарья С.Order No. ZK-2025/850 · 18 May 2025
oursТехника на гарантии уже не была, так что выбор был свободный. Посмотрели, назвали срок — два дня. Уже полгода — ни одного сбоя)
Светлана Д.Order No. TS-2403-875 · 8 April 2024
oursҰзақ уақыт бойы жөндеуге беретін жер іздедім. Бір күнде жөндеп берді, кешіктірмеді. Мастер кешке дейін күтпей, сол күні аяқтады. Кәсіби мамандар, рақмет)
Виктор Ф.Order No. ZK-2023/694 · 20 November 2023
oursЗаметил случайно: не холодит. Посмотрели, назвали срок — два дня. Проверил дома — всё на месте, ничего не забыли.
Юлия А.Order No. ZK-4823 · 21 January 2021
oursОбидно было, техника не старая совсем. Больше всего напрягало: ошибка. Ответили быстро, не пришлось ждать на линии. В списке работ — плата. Заплатил 18 500, и не жалею. Гудит ровно, не греется, всё как надо.
Алия Ш.Order No. TS-2003-173 · 18 January 2020
oursБыло важно, чтобы сделали до выходных — гости, то-сё. Нужен был ремонт мобильного кондиционера — обратился сюда. Основная жалоба — течёт. Уже полгода — ни одного сбоя.
Талгат С.Order No. 524316 · 25 September 2018
oursИскал мастерскую поближе к дому, чтобы не мотаться с техникой через полгорода. Симптом был очевидный: не холодит один блок. Шум пропал, работает мягко.
Светлана Д.Order No. ZK-2018/261 · 4 March 2018
oursБұрын басқа сервиске барғанмын, бірақ бұл жолы осында келдім. Техника кенеттен істен шықты, қатты асығыс едім. Жұмыс барысын көрсетіп отырды, жасырған жоқ. Тексеру кезінде бәрін өзі көрсетті. Бағасы базардағыдан қымбат емес. Қосымша бөлшек қажет болды, бірақ бағаны көтермеді. Себебі қуат беру модулінде екен, бір сағаттың ішінде ауыстырды. Диагностика тегін болды, бұл жағы жақсы. Мастер ақауды түсіндірді, қажетсіз нәрсе таңбады. Бағасы мен сапасы сай.
Didn’t find the answer? Message us on WhatsApp.
Ask a questionMost often it's a refrigerant leak or a clogged filter and heat exchanger — the compressor hums but there's no cold air. Less commonly, the cause is a sensor or circuit board. A technician will pinpoint the exact issue during free diagnostics.
In a sealed General system, refrigerant isn't consumed and lasts for the entire life of the unit. If refrigerant needs to be added, there's a leak: it should be found and fixed, not just topped up.
At Tech Service, the request is handled by the service itself, with no middlemen or aggregators: our own technician arrives at your home anywhere in the city within 60 minutes. Diagnostics are free, and there's a 1-year warranty on labor and parts.
It depends on the model and the type of damage: sometimes replacing a single component is enough, while a serious defect calls for a new board. The technician decides after inspecting the unit.
With a leak, a General unit cools poorly, frost appears on the pipes, and the compressor runs nonstop. The exact diagnosis is made by a technician after free diagnostics: checking pressure and looking for the leak.
Before the technician arrives, check the remote and its batteries, the operating mode, the filters, and whether the outdoor unit is blocked. This will help find the cause faster, but you shouldn't take the unit apart or add refrigerant yourself.
Tech Service repairs General air conditioners in Almaty as a direct contractor: our technician comes to your home within 60 minutes or accepts the unit at our service center. Diagnostics are free, there's a 1-year warranty on labor and parts, and our technicians have 4 to 20 years of experience. The price is given after diagnostics.
A symptom on the panel is not a diagnosis yet. We break down what's behind each common sign on a General unit and how the cause relates to the symptom.
If your General unit is humming and blowing but the air is warm, the most common culprits are clogged filters and heat exchanger, a refrigerant leak, or a blocked outdoor unit. Coarse filters get clogged with dust over a season and block airflow through the heat exchanger — cooling capacity drops even though the compressor is working fine. A leak in the refrigerant line gives the same symptom: pressure in the circuit drops, and the unit just moves air without cooling. A clogged outdoor unit prevents heat dissipation, the condenser overheats, and the operating cycle breaks down. A technician distinguishes these causes by circuit pressure and pipe temperature, not just by the feel of warm airflow. Clogs and leaks produce a similar symptom but are fixed differently — so before recharging, the technician looks for a leak; otherwise the refrigerant will escape again. The check takes a few minutes and is done before any work on the circuit. If you need General Climate AC repair in Almaty, the technician first finds the cause and only then proceeds with the fix.
Water leaking from the indoor unit of a General is usually due to a clogged drain or a displaced tube, while the on-off cycle is tied to sensor protection or overheating. The drainage system collects condensate from the heat exchanger; when the drain gets clogged with dust and slime, water accumulates in the pan and overflows into the room. A displaced or pinched tube has the same effect — drainage stops working, and moisture runs down the casing. Frequent stops are related to temperature sensors: the control system detects overheating or freezing and takes the compressor offline. An outdoor fan that has lost speed also triggers overheating protection for the condenser. Frequent shutdowns are not a breakdown in themselves but a reaction of the control system; it's important to understand which parameter is out of range. By the nature of the pause — short or long — the technician narrows down the causes even before disassembly.
Humming during operation on a General usually comes from fan bearings or imbalance, while failure to start after winter is due to moisture, oxidized contacts, or low refrigerant. Bearing wear increases fan blade vibration, and noise grows with speed. An imbalanced indoor unit wheel gives a low hum at startup, and worn bushings in the outdoor fan add a metallic note. After a long idle period, moisture condenses on contacts and the board, oxidation breaks the control circuit, and the unit won't start. A four-way valve stuck over winter disrupts the mode and prevents startup. Before the first start after idle time, it's useful to let the equipment dry out and check that the outdoor unit isn't clogged with leaves. If it still won't start after drying, the next step is instrument measurements, not repeated attempts to turn it on.
A code on the display narrows the search to a specific component. We show the decoding logic and how to tell a refrigerant leak from a compressor failure — by the unit's behavior, not just the label.
We decode a General error code using the brand's service table and cross-check it with the actual behavior of the components, not just the display message. The symbol on the screen points to a specific component — temperature sensor, control board, drain, or inter-unit communication — and that eliminates half the possibilities before disassembly. Next, the technician checks the element itself and its circuit: continuity testing and sensor resistance measurement take minutes, whereas replacing a working board based on the code alone means extra costs for the owner. In my experience, half of the "scary" codes on splits of this brand end with cleaning an oxidized connector. The same symbol can point to the element itself or its circuit, so the technician checks both the part and the contact.
We check for refrigerant leaks before recharging: if the pressure drops while the compressor is running, the problem is in the circuit, not the unit itself. The refrigerant line is a closed system, and a pressure drop means refrigerant is escaping through a joint, a flare fitting, or a microcrack in the tubing. Diagnostics quickly distinguish two scenarios: a running compressor with low pressure indicates a leak, while a stopped compressor with normal pressure points to a failure in the start relay or protection circuit. We locate leaks by applying soapy water to joints and inspecting the line, not by blindly adding gas. Recharging without finding the leak gives only a temporary fix—refrigerant will escape through the same spot within weeks. That's why when cooling drops again, our team first checks the circuit for leaks and only then discusses the recharge amount with the owner.
| Code group | What we check | Common cause |
|---|---|---|
| Temperature sensor | circuit and sensor itself | open circuit or oxidized contact |
| Drainage | pump and drain hose | clog, condensate blockage |
| Unit communication | cable and board | loose contact |
| Compressor | start and protection | overload, wear |
An inverter General is built differently from a conventional unit: the control electronics and a variable-speed compressor take center stage. Here's what parts fail and which ones we repair versus replace.
In inverter General units, we most often deal with control electronics, the power module, and temperature sensors rather than the compressor itself. The electronic board sits next to the outdoor unit and operates under constant heat load. A dust-clogged outdoor coil overheats, the power module draws higher current, and the control board is the first to fail. Temperature sensors then start giving false readings: the system gets incorrect data about air and refrigerant temperature, the compressor runs at the wrong speed, and errors accumulate. A power surge finishes off already weakened electronics—this happens regularly in private homes and older buildings. The board doesn't fail on its own—it's often killed by a voltage spike or overheating due to a clogged outdoor unit, so at the first sign of failure, check the coil's cleanliness, not just the microchips.
We first check the General control board for repairability and replace it entirely if the damage affects the power section. A local defect—a blown capacitor, a burnt fuse, a lifted trace—can be fixed by soldering and replacing individual components. A burnt power module, charred traces, or processor damage make restoration pointless: the board won't handle the load after that. Diagnostics determine what to do next—repair or replace—and that decision is based on the nature of the damage, not on preference. We provide a 1-year warranty on replaced parts, just as on labor. The decision depends on the damage: a local defect can be repaired, but a burnt module is cheaper and more reliable to replace than to rebuild piece by piece.
| Parameter | Conventional General | Inverter General |
|---|---|---|
| Key part | compressor, start relay | board, power module |
| Common failure | start, refrigerant | electronics, sensors |
| Diagnostics | mechanics and circuit | electronics and circuit |
| What we check | pressure, start | board signals, sensors |
Getting your General air conditioner repaired in Almaty directly from a technician is different from going through a middleman. Here's how the process works and what you can check yourself.
We're the direct contractor: our own staff technician comes to your address, not a dispatcher from an aggregator who passes the request to a subcontractor. Our specialists have worked with General air conditioners for 4 to 20 years and know both lines — standard and inverter split systems. The same service that takes your request is the one responsible for the result: you don't have to figure out who will actually show up or who to complain to about quality. Diagnostics are free, so the "look first, decide later" approach doesn't turn into an extra expense. When you go through a middleman, warranty responsibility is split between the dispatcher and the contractor, but with a direct technician there's only one party — we provide a 1-year warranty on labor and parts.
Our technician arrives at your home within 60 minutes anywhere in the city, performs free diagnostics, and gives you the price before any work starts. The inspection includes checking the pressure in the circuit, examining the board, and measuring compressor currents — based on this, the specialist identifies the cause instead of just saying "something's wrong with the refrigerant." The price is quoted after the inspection and before disassembling any components: work doesn't begin until you agree, and payment options are discussed on site — you can pay via Kaspi QR, Kaspi Red, card, cash or bank transfer. On-site repair isn't always possible: with complex electronics, the air conditioner is taken to the service center, and this is discussed in advance, before the visit, not sprung on you at your address. The technician asks about the model and symptoms over the phone beforehand so they can bring the right tools for your specific General series.
Service terms matter as much as the work itself: they determine what a repeat visit will cost and how quickly the problem gets resolved. Here's a breakdown of the warranty, payment process, and what goes into the final price — no surprises.
We provide a 1-year warranty on labor and parts, so if the same issue comes back due to our fault, the service continues under warranty. This covers the entire scope of work performed: inverter board soldering, compressor replacement, circuit recharging, and replacement of sensors and fans. Technicians with 4 to 20 years of experience record in the work order which component was replaced and what operation was performed — this record helps quickly identify the cause if you come back. Separate warranty coverage for the part and for the installation covers both scenarios: if the part itself fails, it's replaced under warranty; if there's an installation error, the work is redone. This distinction eliminates disputes about who's responsible for the breakdown. Before the technician leaves, ask them to show you the record of replaced components — it's easier to stand up for your rights if the same component acts up again.
Our technician gives you the price after a free diagnostic, and you can pay in any way that suits you — via Kaspi QR, Kaspi Red, bank card, cash, or bank transfer for companies. The diagnostic shows which component has failed: a refrigerant leak in the circuit, compressor wear, a control board fault, or a clogged drain. Based on the results, the technician explains the scope of work and gives you the final amount before starting, so it doesn't go up during the job. The same diagnostic helps you decide whether repair or replacement is more cost-effective: sometimes replacing a component costs less than repeated visits, and sometimes it's enough to clean the drain and top up the circuit. A technician arrives anywhere in the city within 60 minutes, and on site immediately matches the symptom to the error code — this reduces unnecessary disassembly of the unit. Ask in advance what operations are included in the quoted amount so there are no extra charges for removing a panel or checking pressure.
Here's what matters most for getting your General air conditioner serviced: from an accurate diagnosis of the faulty component to maintenance that delays the next technician visit.
80brands
We work with air conditioners and split systems of every brand sold in Kazakhstan — from Almacom, Gree and Midea to LG, Samsung, Chigo and rare imported makes. Can’t find yours in the list? Call anyway — a technician will come and take a look.
Tech Service technicians repair other appliances too — with the same 1-year warranty on labour and parts.
Refrigerator Repair in Almatyfrom 3 000 ₸
Washing Machine Repair in Almatyfrom 3 000 ₸
Dishwasher Repair in Almatyfrom 3 500 ₸
Oven Repair in Almatyfrom 3 000 ₸
Cooktop Repair in Almatyfrom 3 500 ₸
Air Conditioner Repair in Almatyfrom 3 500 ₸
Boiler and Water Heater Repair in Almatyfrom 2 500 ₸
Freezer Repair in Almatyfrom 6 000 ₸
Tumble Dryer Repair in Almatyfrom 5 000 ₸
Coffee Machine Repair in Almatyfrom 2 500 ₸
Robot Vacuum Cleaner Repair in Almatyfrom 3 500 ₸
Vacuum Cleaner Repair in Almatyfrom 1 500 ₸
Microwave Oven Repair in Almatyfrom 2 000 ₸
Hair Dryer Repair in Almatyfrom 1 500 ₸
Iron Repair in Almatyfrom 3 000 ₸
Electric Kettle Repair in Almatyfrom 2 500 ₸
Mixer Repair in Almatyfrom 2 500 ₸
Multicooker Repair in Almatyfrom 500 ₸
Air conditioner errors are codes on the display or flashing indicators that show which component has failed.
5 March 2026 · 12 minutes read
If your air conditioner is leaking, first turn it off and cut the power, place a container under the drip, and move any wiring away from the water.
19 October 2025 · 12 minutes read
Gas boiler errors are codes on the display or a flashing indicator that point to a specific component: ignition, pressure, draft, sensor, or control board.
10 February 2026 · 11 minutes read












