experience9 yearsRuslan Ts.
Washing machine and refrigerator repair technician
City
Language
What broke
Sections
Message on WhatsApp+7 (778) 021 13 16Mon–Fri 10:00–19:00, Sat–Sun 11:00–18:00
A technician arrives within 60 minutes anywhere in the city. Free diagnostics.
Our own technicians4 to 20 years of experience




Repair prices
Below are typical symptoms and causes that the technician checks first.
discharged battery, fuse, controller
from3 000 ₸
Hall sensor, phase wire break, throttle
from6 500 ₸
code points to a specific component
from4 000 ₸
bearing, magnet, bushing
from4 000 ₸
bearings, clamp
from4 000 ₸
port, charger, BMS
from5 000 ₸
pads, disc, cable
from1 500 ₸
seized, winding break
from5 000 ₸
The table lists the 'from' price for labor, for common jobs also the 'from' price of the part, plus the time required to complete the job.
1–2 hourstime
from 3 000 ₸cost

BeforeAfter5 steps

Five steps from request to final check.
Submit a request, describe the symptoms and your scooter model.
The technician arrives anywhere in the city within 60 minutes.
The technician lists the work and parts before starting the repair.
Work is done after the scope and price are approved.
After reassembly, the technician and the owner check ride quality, brakes and electronics.
The home appliance repair department in Almaty has 8 technicians with 8 to 12 years of experience.

The department has 8 specializations — they are listed on the technicians' cards.
experience9 yearsWashing machine and refrigerator repair technician
experience12 yearsGeneral household appliance repair technician
experience10 yearsField technician for washing machine and refrigerator repair
experience8 yearsExpert washing machine repair technician
experience8 yearsField refrigerator repair technician
experience8 yearsSenior washing machine repair technician
experience11 yearsDishwasher repair technician
experience9 yearsWashing machine repair technician
We reply during working hours
Ask if a consultation without a visit is possible if the scooter is under warranty or the fault is minor. 1-year warranty on labor and parts.

Warranty question? Call us
+7 (778) 021 13 167 898 reviews of repairs at TECH SERVICE in total
Тимур И.Order No. 318615 · 16 December 2025
oursДо этого обращался в другой сервис, там только развели руками. Привёз на диагностику: электросамокат. Больше всего напрягало: сломался контроллер. Отдельно спосибо мастеру — Максим Снегирев, терпения ему хватило. Проверили на всех режимах, всё чётко
Роман З.Order No. TS-2206-392 · 20 May 2022
oursПервое, что заметил: сломался контроллер. Максим Снегирев возился с этим дольше, чем планировал, но довёл до конца. Функции все на месте, ничего не отвалилось.
Айгерим Б.Order No. 869927 · 23 October 2020
oursНужен был счёт и чек, у нас техника на балансе организации. Основная жалоба — сломался контроллер. Ребёнок уже проверил на прочность, держится.
Гаухар Н.Order No. ZK-2559 · 7 September 2020
oursНужен был счёт и чек, у нас техника на балансе организации. Привёз на диагностику: электросамокат. С чем пришёл: не держит заряд. Заплатил 10 500, и не жалею. Заодно поменяли: контроллер. Объяснили по телефону, что можно не везти, но я всё равно привёз. С чистой совестью советую. Даже настройки не сбились, что удивительно
Ерасыл Б.Order No. 2019-2110 · 13 October 2019
oursСначала просто глючило, потом стало хуже: сломался контроллер. Приехал вечером, мастер ещё был на месте. Из деталей — мотор. Оплатил картой, чек дали. Починили и дали гарантию на месяц.
Артём К.Order No. ZK-1866 · 16 September 2018
oursПриехал из командировки, а дома — сломался контроллер. Созвонились, договорились на удобное время, никто не тянул. Поставили новую деталь: аккумулятор. Отдал 15 500, и это вместе с работой. Не пожалел ни разу. Проверил дома — всё на месте, ничего не забыли
Сабина Г.Order No. ZK-2018/960 · 8 August 2018
oursПозвонил в три места, здесь единственые назвали цену сразу. Основная жалоба — сломался контроллер. Даже настройки не сбились, что удивительно.
Динара М.Order No. ZK-2018/787 · 23 March 2018
oursИскал мастерскую поближе к дому, чтобы не мотатся с техникой через полгорода. Привёз на диагностику: электросамокат. Первое, что заметил: не едет. Позвонили заранее, предупредили, что задержится на полчаса. Нужна была замена: мотор. По деньгам вышло адекватно, в другом месте просили больше. В общем, доволен. Вернули в тот же день, всё функционирует)
Куаныш Б.Order No. ZK-2017/323 · 20 September 2017
oursЦена имела значение, но и гарантия тоже. Сначала просто глючило, потом стало хуже: не едет. Оплатил картой, чек дали. Нужна была замена: контроллер. Приехал вечером, мастер ещё был на месте. Считаю, что нашёл своего мастера. Работает как раньше, придирок нет.
Аскар Ж.Order No. 722574 · 24 February 2017
oursҚарапайым ғана ақау деп ойладым, бірақ басқаша болып шықты. Тек кезекте аздап күттім.
Didn’t find the answer? Message us on WhatsApp.
Ask a questionYes, technicians do handle such cases: after moisture exposure, the scooter often won't turn on due to oxidized contacts or circuit board. It depends on the model and extent of damage, but diagnostics will show what can be restored.
You can lift the wheel and spin it by hand: it should rotate smoothly without sticking or unusual noise. If there's play or jerking while riding, a technician needs to check it, depending on the model.
Jerking during acceleration is more often related to the controller, hall sensor in the hub motor, or wiring. The exact cause is determined by a technician during free diagnostics, depending on the scooter model.
In most cases, the knocking is fixed by adjustment and replacement of worn bearings or bushings, not by replacing the entire column. What exactly is needed, the technician will say after inspection, depending on the model.
Some Ninebot battery faults are fixed by restoration, but deep cell wear requires unit replacement. What suits your case will be shown by free diagnostics, depending on the model.
Don't try to charge the scooter right away: moisture inside can cause a short circuit. Dry the body and take the Ninebot to a technician for diagnostics to check the board and contacts, depending on the model.
Tech Service repairs Ninebot electric scooters in Almaty with its own technicians: a mobile technician arrives at your home within 60 minutes, or the repair is done at the service center. Diagnostics are free, there is a 1-year warranty on labor and parts, and the technician gives you the price after diagnostics. Our technicians have 4 to 20 years of experience.
Breakdowns on scooters of this brand happen by assembly: power, traction, steering, folding mechanism. Let's go through the typical symptoms owners come to us with and what each of them means.
We see two different scenarios: the scooter doesn't start at all — then the cause is in the power, battery, or controller. It can be different: the unit starts but doesn't ride — then the motor wheel, wiring, or sensor is to blame. In the first case, we check the voltage at the battery connectors, the integrity of the harness, and the board's response to turning on. In the second, we spin the wheel by hand, check the winding resistance, and look for a break in the wiring and connectors between the motor and the board. This sequence rules out half the false versions before disassembly. The symptom "turns on but doesn't ride" more often points to the motor wheel or a break in the wiring, not the battery, so diagnostics should start with traction, not charge.
We associate jerking during acceleration with the controller, sensor, or wiring, and knocking in the steering column with play in the assembly, which is checked on site. Jerks at start appear when the board loses the signal from the position sensor or a contact in the connector burns under load. Knocking in the steering indicates wear in the bearings or loose fasteners — it's heard on bumps and when braking with the front wheel. We roll the scooter under load and at idle: the difference in behavior immediately shows whether it's electronics or mechanics. If jerks occur only under load and the ride is smooth at idle, the version with the board or contact is confirmed, and mechanics is ruled out. The opposite case — smooth start and knocking on every bump — points to the bearings and steering fasteners.
A signal on the display and a blinking indicator are the starting point for diagnostics, not a ready diagnosis. Let's break down how we read Ninebot signals and why we don't replace a part based on just a number on the screen.
We read the error code on the Ninebot display as a pointer to an assembly, not as a verdict: it narrows the check to the battery, controller, motor wheel, or wiring. The number on the indicator panel alone doesn't say what exactly failed — the E-code only sets the direction of the search. Then comes measurement: voltage at the battery connector, signals from the Hall sensors in the motor, integrity of the harnesses and contacts of the control board. Our technicians have worked with this brand for four to twenty years and can already tell typical combinations from the unit's behavior during diagnostics. The same number can appear for different reasons, so the decoding should be confirmed by measurement, not by replacing a part based on just the value on the screen.
A blinking battery indicator usually points to a problem in the power chain — from the battery cells to the controller — not just a low charge. This chain has three links: the battery cells themselves, the battery management board, and the wiring to the control board. The blinking can come from any of them. We check the charger separately: its condition is confirmed by measuring the output voltage at the connector, not by the blinking pattern on the scooter body. We provide free diagnostics, so the owner doesn't pay for guesswork and gets a precise answer about the faulty component. If the indicator blinks when the battery is fully charged, you need to check the battery and contacts, not the charger — otherwise replacing the charger won't solve the problem.
| Symptom | Battery issue | Controller issue |
|---|---|---|
| Range | dropped sharply | unchanged |
| Behavior under load | voltage sag | jerking and cutouts |
| Display errors | power-related | control-related |
| Reaction to full charge | symptom persists | symptom persists |
When a Ninebot won't charge, the battery isn't always to blame. Here's how we check the power chain and what we do with the battery next.
We restore a Ninebot battery by resoldering cells or replace the whole pack — the choice depends on the condition of the pack and its casing. First we open the compartment and check the BMS board, cell balance, and internal resistance: these measurements show whether individual cells have degraded or the entire battery has weakened. Resoldering restores capacity when the power electronics and casing are intact and only one or two cells have dropped. If the control board is damaged, the casing is warped, or moisture has affected the pack, a new pack is more reliable — a restored battery in such condition holds charge unpredictably. We provide a 1-year warranty on both resoldering and pack replacement, covering labor and parts. Resoldering makes sense when the casing and board are intact and only individual cells have degraded; if the case or electronics are damaged, replacement is more reliable.
We perform Ninebot battery replacement in Almaty both on-site and at our service center, and before replacing we check for free whether the battery is really the issue. A technician arrives within 60 minutes in the city, opens the compartment, and tests the power circuit: charger, connectors, wiring to the controller, and the battery terminals. This approach prevents unnecessary replacements — sometimes the owner is ready to change the battery, but a weak contact in the port or an oxidized terminal produces the same picture. Based on the diagnostics, we quote the price and agree on the work: a new pack, cell resoldering, or wiring repair. You can pay via Kaspi QR, Kaspi Red, bank card, cash, or bank transfer for companies. A new battery won't restore range if the cause is in the controller or wiring, so we check the power chain before replacement, not after.
Water damage and firmware are two scenarios where a wrong step is costly. Here's how we handle them to avoid making the damage worse or turning a minor defect into a component replacement.
If your Ninebot got caught in the rain and won't turn on, we first dry and inspect the electronics rather than trying to start it again. Moisture on the controller board shorts the traces and connectors, and under voltage oxidation speeds up — traces burn out in minutes. Disassembly and inspection take part of the visit, but they give you the real picture: where water is pooling, which connectors have turned green, and whether the board is intact. Next we check the wiring along its entire length — from the throttle to the hub motor — because water collects at the bottom of the deck near the battery terminals. Turning the scooter back on after it gets wet is the main reason water turns from a surface problem into a burnt-out controller, so it's best to cut the power right away.
We test the Ninebot firmware and update it when necessary, but we're careful with reflashing because a failed attempt can damage the controller. The firmware version is tied to current parameters and cutoffs — with an incompatible build the motor starts to jerk and error codes appear on the display that weren't there before. We compare the current version with the one that suits the specific model and board revision, and update only when there's a clear need: if the firmware doesn't solve the problem, there's no reason to touch it. We also check separately for any traces of moisture on the board connectors: a damp contact causes the same jerking, and reflashing won't help there. If errors or jerking appear after the update, it's usually an incompatible version rather than a hardware issue, so flashing should be done before replacing the controller, not after.
We build our Ninebot service around three things: a technician visit, free diagnostics before work, and a 1-year warranty. Below is how each stage works and what it gives the owner.
We're a direct provider: our technician comes to your home within 60 minutes anywhere in the city, or you can bring the scooter to the service center — whichever is more convenient. The visiting technician brings tools for disassembling the deck, inspecting connectors, and checking the controller, so some faults are fixed on the spot. Battery disassembly, board soldering, and load testing are done at the service center, where there are proper conditions for power and Ninebot electronics. The owner chooses: a quick look at why the scooter won't turn on — at home, while deep restoration of a unit — at the facility. A home visit is convenient for inspection and simple jobs, while a complex case involving the battery or board is usually handled at the service center, where the scooter can be run under load. So Ninebot electric scooter repair in Almaty happens in the format that suits the owner — at home or at the facility.
Diagnostics are free, and the technician quotes the price after them, once it's clear what exactly needs to be restored. First he tests the power, connectors, battery condition, and controller, runs the scooter under load, and then states the scope of work. This order removes the main fear of a Ninebot owner — being charged for replacing a working unit: first you see the real scope of tasks, then you make a decision. The home visit format doesn't change the logic: even at your home, the technician first shows the inspection results and only then discusses which unit to restore. Approving after tests protects you from unnecessary work — you pay for what's actually broken, not for the technician's guesses. And the specialist doesn't replace a unit until he's checked it under load in assembly.
| Step | How it works | What you get |
|---|---|---|
| Inspection | free, on-site or at the service center | a clear scope of work |
| Repair | at your home or at our facility | work by a technician with 4 to 20 years of experience |
| Parts replacement | based on the inspection results | 1-year warranty on parts |
| Payment | Kaspi QR, Kaspi Red, card, cash or bank transfer | the agreed price after inspection |
Here's what a Ninebot owner should keep in mind before calling a technician — from decoding the code on the screen to avoiding making the damage worse after rain.
11brands
We repair Ninebot and other brands that have dedicated pages on this site.
Tech Service technicians repair other appliances too — with the same 1-year warranty on labour and parts.
Refrigerator Repair in Almatyfrom 3 000 ₸
Washing Machine Repair in Almatyfrom 3 000 ₸
Dishwasher Repair in Almatyfrom 3 500 ₸
Oven Repair in Almatyfrom 3 000 ₸
Cooktop Repair in Almatyfrom 3 500 ₸
Air Conditioner Repair in Almatyfrom 3 500 ₸
Boiler and Water Heater Repair in Almatyfrom 2 500 ₸
Freezer Repair in Almatyfrom 6 000 ₸
Tumble Dryer Repair in Almatyfrom 5 000 ₸
Coffee Machine Repair in Almatyfrom 2 500 ₸
Robot Vacuum Cleaner Repair in Almatyfrom 3 500 ₸
Vacuum Cleaner Repair in Almatyfrom 1 500 ₸
Microwave Oven Repair in Almatyfrom 2 000 ₸
Hair Dryer Repair in Almatyfrom 1 500 ₸
Iron Repair in Almatyfrom 3 000 ₸
Electric Kettle Repair in Almatyfrom 2 500 ₸
Mixer Repair in Almatyfrom 2 500 ₸
Multicooker Repair in Almatyfrom 500 ₸
If your dishwasher won't drain, the most common culprits are a clogged filter or drain hose; less often, it's the pump, impeller…
24 March 2026 · 12 minutes read
A washing machine can hum for many reasons, and the first thing to figure out is when the sound appears.
20 March 2026 · 12 minutes read
If your washing machine isn't filling with water, the most common culprits are a closed valve, a clogged inlet filter screen on the hose…
20 February 2026 · 13 minutes read
If your microwave isn't heating but the light and turntable still work, the problem is usually one of the high-voltage components — the magnetron, diode…
15 February 2026 · 12 minutes read
If your refrigerator stops working, first check the outlet, the power cord, and the thermostat setting, and after defrosting let it stand for a while.
4 February 2026 · 12 minutes read
Washing machine error codes are self-diagnostic codes that point to a specific component: drain, water fill, heating, motor, or door lock.
29 January 2026 · 13 minutes read












