experience9 yearsRuslan Ts.
Washing machine and refrigerator repair technician
City
Language
What broke
Sections
Message on WhatsApp+7 (778) 021 13 16Mon–Fri 10:00–19:00, Sat–Sun 11:00–18:00
A technician arrives within 60 minutes anywhere in the city. Free diagnostics, 1-year warranty on labor and parts.
Our own technicians4 to 20 years of experience




Repair prices
The symptoms customers most often report. The technician will pinpoint the exact cause after free diagnostics.
discharged battery, protection mode, broken circuit
from2 500 ₸
faulty charger or connector
from5 000 ₸
controller, phase break, motor seizure
from3 000 ₸
loose bolts, worn bearings
from4 000 ₸
worn battery cells, increased load
from4 500 ₸
natural wear, impact
from2 000 ₸
worn pads, stretched cable
from1 500 ₸
overheating, moisture, wiring
from2 500 ₸
The table lists the 'from' price for labor, for common jobs also the 'from' price of the part, plus the time required to complete the job.
1–2 hourstime
from 3 000 ₸cost

BeforeAfter5 steps

From request to check — five steps. Diagnostics are free.
Send a request by phone or WhatsApp and describe the symptoms.
The technician will arrive anywhere in the city within 60 minutes of your request.
After the inspection, the technician will agree on the next steps and the time of work with you.
You approve the work plan and cost, then the technician starts the repair.
You test the scooter and accept the result.
The home appliance repair department in Almaty has 8 technicians with 8 to 12 years of experience.

The department has 8 specializations — they are listed on the technicians' cards.
experience9 yearsWashing machine and refrigerator repair technician
experience12 yearsGeneral household appliance repair technician
experience10 yearsField technician for washing machine and refrigerator repair
experience8 yearsExpert washing machine repair technician
experience8 yearsField refrigerator repair technician
experience8 yearsSenior washing machine repair technician
experience11 yearsDishwasher repair technician
experience9 yearsWashing machine repair technician
We reply during working hours
Describe the symptoms by phone or WhatsApp — the technician will advise on the next steps. It's convenient to send a request when the scooter is at hand.

Warranty question? Call us
+7 (778) 021 13 167 898 reviews of repairs at TECH SERVICE in total
Тимур И.Order No. 318615 · 16 December 2025
oursДо этого обращался в другой сервис, там только развели руками. Привёз на диагностику: электросамокат. Больше всего напрягало: сломался контроллер. Отдельно спосибо мастеру — Максим Снегирев, терпения ему хватило. Проверили на всех режимах, всё чётко
Роман З.Order No. TS-2206-392 · 20 May 2022
oursПервое, что заметил: сломался контроллер. Максим Снегирев возился с этим дольше, чем планировал, но довёл до конца. Функции все на месте, ничего не отвалилось.
Гаухар Н.Order No. ZK-2559 · 7 September 2020
oursНужен был счёт и чек, у нас техника на балансе организации. Привёз на диагностику: электросамокат. С чем пришёл: не держит заряд. Заплатил 10 500, и не жалею. Заодно поменяли: контроллер. Объяснили по телефону, что можно не везти, но я всё равно привёз. С чистой совестью советую. Даже настройки не сбились, что удивительно
Ерасыл Б.Order No. 2019-2110 · 13 October 2019
oursСначала просто глючило, потом стало хуже: сломался контроллер. Приехал вечером, мастер ещё был на месте. Из деталей — мотор. Оплатил картой, чек дали. Починили и дали гарантию на месяц.
Максат О.Order No. ZK-2018/311 · 2 October 2018
oursЦена имела значение, но и гарантия тоже. Симптом был очевидный: не держит заряд. Сделали и забыл про проблему.
Артём К.Order No. ZK-1866 · 16 September 2018
oursПриехал из командировки, а дома — сломался контроллер. Созвонились, договорились на удобное время, никто не тянул. Поставили новую деталь: аккумулятор. Отдал 15 500, и это вместе с работой. Не пожалел ни разу. Проверил дома — всё на месте, ничего не забыли
Сабина Г.Order No. ZK-2018/960 · 8 August 2018
oursПозвонил в три места, здесь единственые назвали цену сразу. Основная жалоба — сломался контроллер. Даже настройки не сбились, что удивительно.
Динара М.Order No. ZK-2018/787 · 23 March 2018
oursИскал мастерскую поближе к дому, чтобы не мотатся с техникой через полгорода. Привёз на диагностику: электросамокат. Первое, что заметил: не едет. Позвонили заранее, предупредили, что задержится на полчаса. Нужна была замена: мотор. По деньгам вышло адекватно, в другом месте просили больше. В общем, доволен. Вернули в тот же день, всё функционирует)
Куаныш Б.Order No. ZK-2017/323 · 20 September 2017
oursЦена имела значение, но и гарантия тоже. Сначала просто глючило, потом стало хуже: не едет. Оплатил картой, чек дали. Нужна была замена: контроллер. Приехал вечером, мастер ещё был на месте. Считаю, что нашёл своего мастера. Работает как раньше, придирок нет.
Аскар Ж.Order No. 722574 · 24 February 2017
oursҚарапайым ғана ақау деп ойладым, бірақ басқаша болып шықты. Тек кезекте аздап күттім.
Didn’t find the answer? Message us on WhatsApp.
Ask a questionIt depends on the condition: if individual cells or the BMS board fail, the battery can be restored, but with deep cell degradation it's replaced entirely. The technician gives a final verdict after free diagnostics.
Yes, the E Twow hub motor is repaired: bearings are replaced, play is fixed, and wiring is restored if the winding is intact. With a short between turns or a crack in the housing, the unit has to be replaced, which depends on the model.
Turn the scooter off right away, don't try to charge it, and don't press the throttle: water inside the housing can short the controller. Dry the housing in a dry place and take it for diagnostics without turning the power back on.
You can't tell for sure from the symptoms: jerking can come from the Hall sensor in the hub motor, the throttle, or the controller. Diagnostics will help tell them apart — testing the sensors and checking the signal at the controller output.
Yes, play in the E Twow steering column gets worse, and at speed the handlebars can jam or come loose, so riding like that is risky. It can be fixed by adjusting and replacing the bearings if the seats aren't worn out.
Often yes: with blown switches or damaged wiring, the E Twow controller is restored by soldering and reflashing if the board isn't burned. With a charred housing and destroyed traces, the unit is replaced, which depends on the model.
Tech Service repairs E Twow electric scooters in Almaty as a direct contractor: our technician arrives at your home within 60 minutes or picks up the scooter for service. Diagnostics are free, the technician gives you the price after diagnostics, and we provide a 1-year warranty on labor and parts. Our technicians have 4 to 20 years of experience.
The E Twow is a lightweight folding scooter with a compact hub motor. Its low weight and frequent folding distribute stress differently than on heavier models, so it has its own weak points.
Most often, failure to turn on is caused by a discharged or "sleeping" battery, while jerking during acceleration comes from the throttle trigger, Hall sensors, or controller. The battery enters deep-discharge protection and won't deliver current until it's woken up with the correct charger. A throttle trigger with worn contacts sends a fluctuating signal to the controller, so the scooter starts in jolts. Damaged Hall sensors in the hub motor cause the same jerking, but with a characteristic hum and loss of power at low speed. Wiring and connectors are checked first: an oxidized contact at the fold causes both failure to turn on and rough acceleration, and it costs pennies compared to replacing the controller. Starting diagnostics with expensive components means replacing working parts.
After water exposure, connectors, the controller, and the BMS suffer; after winter storage, the battery suffers and goes into deep discharge. Moisture gets into the fold and the battery compartment, oxidizes contacts, and shorts the BMS board traces. The controller is usually the first to fail from water: the scooter won't turn on or stalls while riding. In winter, without recharging, the cells discharge below the threshold, and the BMS blocks the battery until it's restored. The first hours after water exposure matter more than anything you do later: don't turn on or charge the scooter until it's completely dry, otherwise a short circuit will finish off the electronics. After winter storage, check the battery's residual voltage before the first charge—that shows whether it has gone into deep discharge.
The E Twow display shows an error code when the controller detects a fault. It helps you understand which component to check before disassembling the scooter.
We interpret the E Twow signal by the component it points to and check that component first. The display receives data from the controller, which polls the battery with the BMS board, the hub motor with Hall sensors, the throttle, and the brake sensor. Each of these components produces its own set of symbols when it fails, so decoding starts with matching the code to the circuit, not with completely disassembling the scooter. We inspect wiring and connectors at the same time: an oxidized contact on the throttle harness or a damp battery connector often reveals itself with exactly that code. The same code is sometimes caused by different issues—for example, a motor signal can come from either the Hall sensors or the wiring, so it only points you in a direction rather than naming a specific part.
| What the code points to | What we check first |
|---|---|
| Power and battery | charge level, BMS, battery connectors |
| Controller | control board and its connectors |
| Hub motor | Hall sensors and wiring to the wheel |
| Throttle | throttle grip and its cable |
| Brake and regenerative braking | brake sensor and regen settings |
If the code doesn't go away after a restart and a charge, we diagnose it for free instead of guessing from the display. A technician arrives at your door within 60 minutes anywhere in the city and checks the circuit the display flagged on site: tests the wiring, reads data from the BMS board, and checks the Hall sensors and throttle cable. When the fault comes down to the controller board or the hub motor winding, further inspection is done at the service center where the right tools are available. Clearing the code without fixing the cause brings the error back at the first load, so we fix the problem instead of resetting it. This approach saves both time and parts: only the component that actually failed gets replaced, not the whole scooter.
Some E Twow failures are visible before you bring the scooter in. A few simple checks help you figure out whether the battery needs replacing or the issue is with charging and the BMS.
Measure the voltage at the battery connector with a multimeter: noticeably below the rated value means deep discharge or failed cells. First turn off the scooter and remove the load — only at rest does the reading show the real condition of the pack. Compare the result with the rating on the battery case: a drop of 20–30% after winter storage indicates sulfation or cell imbalance. When the voltage is normal but the range has dropped, check the BMS board — it may undercharge a particular group of cells and skew the overall measurement. Next, inspect the connector for oxidation and burnt contacts: after a damp winter they lose conductivity, and charge goes into heating the terminals instead of the cells. Check each block in sequence if the pack is made up of several sections — one weak section drags down the whole chain and distorts the picture. Take the measurement with the scooter off and no load — under load, a sagging voltage tells you nothing about real capacity.
Jerking during braking is more often related to the brake sensor and regen settings than to worn pads. The sensor on the lever sends a signal to the controller with a delay — the electronics switch regen on and off, and the scooter noses down. Check the gap between the magnet and the reed switch at the lever: a shift of a couple of millimeters has the same effect as a failed sensor. An oxidized contact in the wiring harness sends a fluctuating signal to the hub motor, and the power surges unrelated to braking — this fault is easy to mistake for regen. On models with adjustable regen, resetting the profile to factory settings helps: if the jerking stops after that, the issue was in the settings, not the hardware. It's also worth checking the Hall sensor connector in the wheel — moisture in it produces a similar picture in any mode. If jerking occurs both during acceleration and braking, look at the common component — the wiring and controller connectors.
Servicing E Twow electric scooters in Almaty follows a clear process: request, technician visit within 60 minutes, free diagnostics, approval of work, and the repair itself.
We take your request, arrive within 60 minutes anywhere in the city, run free diagnostics, agree on the scope of work, and only then start. The technician inspects the unit, identifies the cause, and lists the operations actually needed. The owner confirms the list before work begins, and after service receives the scooter with a 1-year warranty on labor and parts. You can pay via Kaspi QR, Kaspi Red, bank card, cash, or bank transfer for companies. This keeps the process predictable: first the cause, then the agreed scope, then pickup. On-site we do what can be done carefully at your location, and the rest goes to the shop without losing parts. Approval before starting protects against unnecessary replacements: the owner sees in advance which parts will be touched and which won't. Our E Twow electric scooter repair in Almaty is built on this transparent approach.
| Component | What we do | What we check |
|---|---|---|
| Controller | repair of control board | connectors and board traces |
| Battery and BMS | rebuild of the pack | cells and BMS board |
| Motor wheel | repair and replacement of Hall sensors | winding and wiring to the wheel |
| Throttle and display | repair and replacement | cable and contacts |
| Folding mechanism | fixing play | fasteners and steering column |
Warranty and direct provider are two things E Twow owners check before choosing a service. Here's what the warranty covers and how a direct provider differs from an intermediary.
We provide a 1-year warranty on labor and parts, meaning we stand behind both the quality of work and the installed components. A technician's installation error and a premature failure of a new part fall under the same warranty procedure, so the owner doesn't have to figure out who to claim against. Over a year, a scooter covers significant mileage: bearings, brake pads, and the controller operate under various conditions, so the term covers real use, not just the first weeks after pickup. A separate warranty on parts matters because a part failure and an installation error are handled differently, and the owner shouldn't have to prove whose fault it is. In our experience, this approach prevents disputes before they arise.
Tech Service is the direct provider: your scooter is serviced by our own technician, not by a third-party shop that a middleman forwards the order to. There's no extra link between the owner and the specialist, so the fault is discussed with the person who actually had the device in their hands, not with a dispatcher repeating someone else's words. Our technicians have worked with this brand for 4 to 20 years and know how its controller and hub motor behave on specific models, not from a generic manual. A technician arrives anywhere in the city within 60 minutes, and it's the same person who then stands behind the result. When there's no middleman between the owner and the provider, the scope of work is agreed directly, and unnecessary replacements don't appear "along the way."
The technician quotes the price after free diagnostics, once the scope of work is clear, and you can pay via Kaspi QR, Kaspi Red, bank card, cash, or bank transfer for companies. Before settling the bill, the specialist checks one component at a time and shows you which part has failed, so you can see what you're paying for instead of getting a total with no explanation. If a fault can be fixed by refurbishing rather than replacing, the technician offers that option and explains the difference in reliability: a refurbished component sometimes lasts as long as a new one. Diagnostics before the quote lets you compare refurbishing and replacing a component and choose the option that's better in your specific case. For Almaty residents, it's also a way to avoid paying twice for the same job.
Here are the key points an E Twow owner should keep in mind before contacting a technician: from the model's typical weak spots to how diagnostics work and what the warranty covers.
11brands
E Twow is one of the brands we work with. See the full list of brands below.
Tech Service technicians repair other appliances too — with the same 1-year warranty on labour and parts.
Refrigerator Repair in Almatyfrom 3 000 ₸
Washing Machine Repair in Almatyfrom 3 000 ₸
Dishwasher Repair in Almatyfrom 3 500 ₸
Oven Repair in Almatyfrom 3 000 ₸
Cooktop Repair in Almatyfrom 3 500 ₸
Air Conditioner Repair in Almatyfrom 3 500 ₸
Boiler and Water Heater Repair in Almatyfrom 2 500 ₸
Freezer Repair in Almatyfrom 6 000 ₸
Tumble Dryer Repair in Almatyfrom 5 000 ₸
Coffee Machine Repair in Almatyfrom 2 500 ₸
Robot Vacuum Cleaner Repair in Almatyfrom 3 500 ₸
Vacuum Cleaner Repair in Almatyfrom 1 500 ₸
Microwave Oven Repair in Almatyfrom 2 000 ₸
Hair Dryer Repair in Almatyfrom 1 500 ₸
Iron Repair in Almatyfrom 3 000 ₸
Electric Kettle Repair in Almatyfrom 2 500 ₸
Mixer Repair in Almatyfrom 2 500 ₸
Multicooker Repair in Almatyfrom 500 ₸
If your dishwasher won't drain, the most common culprits are a clogged filter or drain hose; less often, it's the pump, impeller…
24 March 2026 · 12 minutes read
A washing machine can hum for many reasons, and the first thing to figure out is when the sound appears.
20 March 2026 · 12 minutes read
If your washing machine isn't filling with water, the most common culprits are a closed valve, a clogged inlet filter screen on the hose…
20 February 2026 · 13 minutes read
If your microwave isn't heating but the light and turntable still work, the problem is usually one of the high-voltage components — the magnetron, diode…
15 February 2026 · 12 minutes read
If your refrigerator stops working, first check the outlet, the power cord, and the thermostat setting, and after defrosting let it stand for a while.
4 February 2026 · 12 minutes read
Washing machine error codes are self-diagnostic codes that point to a specific component: drain, water fill, heating, motor, or door lock.
29 January 2026 · 13 minutes read












