Open until 19:00+7 (778) 021 13 16Call a technician
Tech Service technician next to a juicer

Bork Juicer Repair in Almaty

We restore extraction and eliminate humming. 1-year warranty on labor and parts.

  • 1-year warranty on labor and parts
  • Technician arrival within 60 minutes across the city
  • Free diagnostics

Our own technicians4 to 20 years of experience

Ruslan Ts.Damir M.Dilmurat S.Dima

Repair prices

  • Diagnostics0 ₸
  • Bearing replacementfrom3 000 ₸
  • Motor replacementfrom4 000 ₸
  • Power circuit repairfrom4 500 ₸
  • Leak repair (seal replacement)from5 500 ₸
All prices
2ГИСЯours4,97 898 reviews
2GIS · Google · Yandex · order database
Common faultsCommon faultsTECH SERVICE02

Common Bork juicer faults in Almaty

Below are typical symptoms Bork juicer owners notice and the likely causes.

PricesPricesTECH SERVICE03

How much Bork juicer repair costs in Almaty

The table lists the 'from' price for labor, for common jobs also the 'from' price of the part, plus the time required to complete the job.

Bearing replacementparts not included

1–2 days

from3 000 ₸

Motor replacementparts not included

1–2 days

from4 000 ₸

Power circuit repairexact price — after the free diagnostics

1–3 hours

from4 500 ₸

Leak repair (seal replacement)parts not included

1–3 hours

from5 500 ₸

Motor brush replacementparts not included

1–2 days

from6 000 ₸

Before and afterBefore and afterTECH SERVICE04

Before and after Bork juicer repair in Almaty

Sparking and losing speed

1–2 daystime

from 6 000 ₸cost

Problem
The Bork juicer sparked inside and lost speed when juicing carrots.
What we did
The technician replaced the motor brushes and checked the juicer's operation.
Result
The sparking stopped and the speed was restored; 1-year warranty on the work and on the parts.
I want the same
On a workshop bench, a juicer motor unit lies on its side with the bottom cover removed: the motor with winding and commutator is visible, and a technician is inserting a new brush into the brush holder with tweezers.BeforeAfter
01 / 03
All repairs
TECH SERVICE mobile technician with a tool case

How Bork juicer repair works at your home in Almaty

Five steps from request to checking the juicer's operation.

  1. Requestby phone

    Describe the symptom and your Bork juicer model so the technician brings the right tools.

  2. Technician arrivalwithin 60 minutes

    Technician arrival within 60 minutes across the city — in Almaty.

  3. Diagnosticsfree

    Diagnostics are free — the technician identifies the cause and agrees on the scope of work with you before starting repairs.

  4. Repair at homesame day

    You approve the scope of work, and the technician performs the repair at home.

  5. Checkafter repair

    We run the extraction together with you and show that the unit works.

Leave a request
TechniciansTechniciansTECH SERVICE05

Our home appliance repair technicians in Almaty

The home appliance repair department in Almaty has 8 technicians with 8 to 12 years of experience.

  • 8 technicians in Almaty
  • 8–12 years of experience in the department
  • Article author Ruslan Ts., 9 years of experience
Mobile technician fixing a washing machine at the customer's home
Field technician at a customer’s home

The department has 8 specializations — they are listed on the technicians' cards.

01 / 08
Ruslan Ts., washing machine and refrigerator repair technicianexperience9 years

Ruslan Ts.

Washing machine and refrigerator repair technician

Damir M., general household appliance repair technicianexperience12 years

Damir M.

General household appliance repair technician

Dilmurat S., field technician for washing machine and refrigerator repairexperience10 years

Dilmurat S.

Field technician for washing machine and refrigerator repair

Dima, expert washing machine repair technicianexperience8 years

Dima

Expert washing machine repair technician

Nikita M., field refrigerator repair technicianexperience8 years

Nikita M.

Field refrigerator repair technician

Oraz, senior washing machine repair technicianexperience8 years

Oraz

Senior washing machine repair technician

Radik T., dishwasher repair technicianexperience11 years

Radik T.

Dishwasher repair technician

Rustem T., washing machine repair technicianexperience9 years

Rustem T.

Washing machine repair technician

We reply during working hours

Book Bork juicer repair in Almaty

Leave a request — a technician will arrive within 60 minutes across the city. Diagnostics are free, 1-year warranty on labor and parts. Ask the technician about payment methods.

TECH SERVICE administrator replying to a customer's WhatsApp message

Warranty question? Call us

+7 (778) 021 13 16
Customer reviewsReviewsTECH SERVICE06

Reviews of Bork juicer repair in Almaty

Жанна О.Order No. ZK-7729 · 25 January 2025

ours

Смотрел, у кого есть запчасти на такую модель. Честно, уже готовился покупать новое, но обошлось. Повод для визита: течёт. Деталь на замену — двигатель. Сказать, что доволен — ничего не сказать

Repair: juicer repair in

Айгерим Б.Order No. 951544 · 25 March 2024

ours

Позвонил знакомому, он раньше работал в сервисе, посоветовал этих. Запчасть была в наличии, доплачивать не пришлось. С тех пор ни разу не подвёл.

Repair: juicer repair in

Алия Ш.Order No. ZK-2023/684 · 4 July 2023

ours

Работаю допоздна, поэтому нужен был сервис с нормальным графиком. Утром столкнулся с тем, что течёт. Ни копейки сверху, как и обещали. Приняли, выдали квитанцию, всё по-человечески. Разобрали, посмотрели: двигатель. Пришлось самому напоминать про гарантийный талон. Не пожалел ни разу. Сделали и забыл про проблему.

Repair: juicer repair in

Руслан Д.Order No. ZK-2598 · 23 April 2021

ours

Позвонил в три места, здесь единственные назвали цену сразу. Нужен был ремонт соковыжималки — обратился сюда. С чем пришёл: не крутит. Радик Т честно сказал, что менять, а что ещё походит. Заявку приняли по телефону, перезвонили через десять минут. Поставили новую деталь: редуктор. Назвали 11 000 сразу, в конце сумма не изменилась. Не понравилось, что нужно оставлять предоплату. Спасибо, выручили. Проверили на всех режимах, всё чётко.

Repair: juicer repair in

Ерасыл Б.Order No. 2021-3299 · 24 February 2021

ours

Поломка застала перед командировкой, тянуть было нельзя. Проблема — вибрирует. Второй месяц — полёт нормальный.

Repair: juicer repair in

Николай Ч.Order No. 35975 · 27 September 2019

ours

Техника на гарантии уже не была, так что выбор был свободный. Повод для визита: не крутит. Позвонил в techservice по объявлению, всё совпало. Проверил дома — всё на месте, ничего не забыли.

Repair: juicer repair in

Павел Ш.Order No. TS-3572 · 26 July 2019

ours

До этого обращался в другой сервис, там только развели руками. Отдал мастеру: соковыжималка. Проблема — не крутит. Проверил дома — всё на месте, ничего не забыли

Repair: juicer repair in

Алия Ш.Order No. TS-1807-228 · 5 September 2018

ours

До этого обращался в другой сервис, там только развели руками. Утром столкнулся с тем, что вибрирует. Из деталей — двигатель. Заявку приняли по телефону, перезвонили через десять минут. Запчасть была в наличии, доплачивать не пришлось. Починили и дали гарантию на месяц.

Repair: juicer repair in

Ержан А.Order No. ZK-2018/910 · 15 March 2018

ours

С чем пришёл: не крутит. Дамир М помог выбрать, без навязывания. Проверил дома — всё на месте, ничего не забыли.

Repair: juicer repair in

Аскар Ж.Order No. 2017-4986 · 23 March 2017

ours

До этого обращался в другой сервис, там только развели руками. Повод для визита: течёт. Ребёнок уже проверил на прочность, держится.

Repair: juicer repair in
See all reviews
Questions and answersQuestionsTECH SERVICE07

Questions about Bork juicer repair in Almaty

Didn’t find the answer? Message us on WhatsApp.

Ask a question
Who in Almaty repairs specifically Bork juicers, not appliances in general?

At Tech Service, Bork juicers are repaired by technicians with 4 to 20 years of experience who come to your home anywhere in the city. We're a direct contractor, not an intermediary, so the same specialist who diagnoses your juicer also repairs it.

Do you repair Bork auger juicers in Almaty?

Yes, we repair Bork auger models: their gearbox, auger, and seals are the most common trouble spots, and we restore these components separately. The technician determines the exact scope of work after a free diagnostics, since the design depends on the model.

Is it worth repairing a Bork auger juicer or is it easier to buy a new one?

Most often, repairing a Bork auger juicer is more cost-effective than replacing it: the gearbox, auger, and seals are repairable. Replacement makes sense if the housing is destroyed or the unit can't be restored, and the technician will explain this after inspection.

My Bork juicer won't turn on — is it the motor or the control board?

One symptom alone can't tell for sure: it could be the motor, the control board, or the power circuit. A free diagnostics at your home helps pinpoint the faulty component, after which the technician names it.

My Bork juicer leaks at the bowl joint — is it the seal or a crack in the housing?

Most often it's a worn seal or gasket, but a crack in the housing or bowl is also possible. On site, the technician checks the joint and determines what to replace so juice doesn't leak during extraction.

Why is it risky to keep using a leaking Bork juicer?

Juice and moisture get inside the housing where the motor and electronics are located, so a leak can cause a short circuit and damage the board. It's best not to use it until the cause is fixed, so a minor repair doesn't turn into replacing components.

Repair guideArticleTECH SERVICE08

Bork juicer repair in Almaty with a technician visiting your home

Ruslan Ts., washing machine and refrigerator repair technician

Author: Ruslan Ts.,Washing machine and refrigerator repair technician

Published
Updated

Tech Service repairs Bork juicers in Almaty: our technician arrives at your home within 60 minutes, or the equipment is repaired at our service center. Diagnostics are free, the technician quotes the price after diagnostics, and there is a 1-year warranty on labor and parts. We handle both centrifugal and auger models, including versions with a display.

Why your Bork juicer won't turn on, won't extract juice, or is noisy

A symptom alone doesn't name the part — it's important to understand which component is behind it. We break down common complaints about Bork juicers and what we check in each case.

Juicer won't turn on even with the lid closed

When a Bork appliance doesn't respond to the button, we first check the magnetic lid lock sensor, then the control board, and only after that the motor. The reed switch sits in the housing opposite a magnet in the bowl lid: if the lock has shifted or the magnet has weakened, the sensor doesn't detect that the lid is closed and blocks startup — while the electronics are fully functional. We check the control board for burnt traces and swollen capacitors, and test the motor separately by supplying power bypassing the circuit. In my experience, most "dead" Bork juicers come back to life after adjusting the lock, not after replacing the board. A common cause is not an electronics failure but a shifted lid lock: the sensor doesn't see the lid closed and blocks startup, so a seemingly "dead" appliance revives after adjusting the gap between the reed switch and the magnet.

Leaking from the bottom at the bowl seam

A leak at the bowl seam on a Bork juicer is most often due to worn seal or oil seal, and a crack in the housing is the second most common cause, which we identify during disassembly. The bowl seal hardens over time and loses elasticity, the drive shaft oil seal lets juice into the motor compartment — both parts are replaced when the assembly is taken apart. We look for a crack along the juice container contour and at the seating ring: a hairline crack in the plastic produces the same drop from below as a worn gasket. If the leak returns after replacing the seal, the technician checks the seating area and drive shaft — a repeat leak almost always indicates deformation of the seam, not the seal itself.

Not extracting juice and leaving wet pulp

Wet pulp in a Bork juicer we associate with a worn filter mesh, clogged sieve holes, or a drop in motor speed, and we check the extraction unit together with the drive. The filter mesh gets clogged with pulp and stops separating juice, the grating disc with worn teeth grinds the product worse, and reduced motor speed doesn't provide enough centrifugal force. The thermal protection switch trips prematurely under overload — then extraction stops mid-cycle and some juice remains in the pulp. We also check how the sieve sits on the shaft: a misalignment of even a couple of millimeters reduces extraction efficiency more than it seems from the part's appearance. A clogged sieve not only causes wet pulp but also puts extra load on the motor, so cleaning the mesh extends motor life and improves extraction.

Hums but the disc doesn't spin, and vibrates heavily

If your Bork juicer hums but the disc doesn't rotate, we check the drive coupling, drive shaft, and bearings; strong vibration during operation indicates worn bearings or shaft play. A broken drive coupling interrupts the transmission from motor to disc — the motor hums but there's no rotation; a seized shaft bearing gives the same symptom with heat in the support area. Vibration appears due to bearing wear or a bent shaft after overload, and on screw models it's amplified by the housing being tilted on an uneven countertop. The thermal protection switch doesn't trip immediately in this mode, so the motor has time to heat up for nothing. Humming without rotation is dangerous because the motor runs under load without doing work and heats up, so it's better not to restart such an appliance before diagnostics — otherwise a overheated winding will be added to the coupling issue.

Components of Bork juicers and how failures differ between centrifugal and screw models

Centrifugal and screw Bork juicers have different working components, so they break in different ways. Below is a component map and a table showing what a technician checks in each type.

Which components are responsible for extraction in centrifugal and screw models

Bork juicer typeJuicing mechanismWhat wears out most oftenWhat we check
Centrifugalgrater disc and mesh filtershaft bearings, sieveRPM, mesh cleanliness, shaft play
Augerauger and gearboxseals, auger shaftsmooth rotation, tightness
With displayelectronics and drivecontrol board, sensorserror codes, response to lid
With combined drivecoupling and shaftdrive coupling, bearingstorque transmission, noise under load

Which Bork juicer parts are actually available

For Bork juicers, we work with consumable and wear parts — seals, oil seals, bearings, mesh filters, drive couplings, and boards — and the technician confirms the exact list after disassembly. Bowl seals and oil seals are replaced most often: they contact juice and pulp and lose elasticity first, and along with them we check how the mesh filter fits on the seating ring. Shaft bearings and the sieve wear from RPM and abrasives, the drive coupling from jerks under load, and the control board from moisture and power surges. Part availability is checked during diagnostics, not by model name: the same line can have different components in different batches, so we can't promise a 'catalog' replacement before opening the unit.

Should you repair a Bork auger juicer or just buy a new one

Repairing a Bork auger juicer usually makes sense if one component has failed — the auger, seals, or drive — rather than the whole unit, and that's only clear after diagnostics. In auger models, the service life is unevenly distributed: the auger itself and the motor last a long time, while seals, bowl oil seals, and the drive shaft wear out first. The gearbox suffers from thick pulp and operation without cleaning, the shaft from misalignment during assembly, and a worn oil seal lets juice reach the bearing and speeds up its failure. Replacing one component gets the appliance working again without buying a new one, and we provide a one-year warranty on the work performed. In my view, it's only worth writing off the unit if the motor is worn out or the housing is cracked — everything else can be repaired component by component.

What the error on the Bork juicer display means

The display on a Bork juicer is a status indicator, not a death sentence. Let's break down what usually lies behind an error and why you can't read the signal without checking the components.

Why an error code appears and what it signals

An error code on the Bork juicer display most often signals that the motor's thermal protection has tripped or that the control board is faulty, rather than a specific 'burnt-out' part. The thermal cutout opens the circuit when the motor winding heats above the allowable limit, and a warning appears on the screen — after cooling, it often disappears on its own. The control board collects signals from the lid lock, tachometer, and temperature sensors, and a failure in any of them produces its own combination of symbols. On models with electronic control, the same symbol can mean an overload from a clogged sieve, a break in the sensor circuit, or a stuck button. The same warning appears for different reasons, so the technician always cross-checks the interpretation with the actual behavior of the components — disc rotation, housing heating, response to closing the lid. The display only records the symptom, while the source of the failure is found by testing the circuit and inspecting contacts; otherwise, replacing the board based on the code blindly won't fix the cause.

What to do when an error occurs and when to call a technician

If your Bork juicer shows an error on the display, we recommend letting it cool down first and checking whether the strainer is clogged. If the signal comes back, call a technician for free diagnostics. The filter mesh gets clogged with fibers after one or two presses of a dense product, the motor runs under load, and the thermal protection trips early — cleaning the strainer resolves half of these calls. If the warning persists after cooling and rinsing, the issue is no longer overload: you need to check the control board, sensors, and motor circuit. A Tech Service technician arrives within 60 minutes anywhere in the city, opens the housing, and tests the components on site. Free diagnostics show which part is triggering the signal. Trying to reset by restarting won't help — the cause is in a component, and you need to find it by disassembling, not by turning it on again. After fixing the issue, we provide a 1-year warranty on labor and parts.

How Bork juicer repair works at Tech Service

Our process is the same for any model — from request to testing with juice. We break down each step and explain what you can check yourself before the specialist arrives.

At home or in the service center — where we repair Bork juicers

We service Bork juicers at the customer's home or in our service center — a specialist arrives within 60 minutes anywhere in the city and determines on site whether the work can be done on the spot or the appliance needs to be taken in. On-site visits cover leaks at the bowl joint, replacing seals, cleaning the pressing unit, and checking the lid closure sensor. For auger and centrifugal models with electronics, our technician brings the right tools for the specific unit so the machine doesn't have to be transported back and forth. If disassembly reveals damage to the board, motor winding, or gearbox, it's better to work on the appliance in the service center, where there's space for a full inspection and lighting for small parts. We repair Bork juicers in Almaty both on-site and in the service center — the format depends on the condition of the appliance. Before the visit, tell us the model — we'll know right away which components to check first.

How free diagnostics work

Diagnostics for Bork juicers is free: the specialist disassembles the components, checks the motor, board, sensors, and pressing unit, and then gives you the cost of work before starting. First, the appliance is run under load and the motor's behavior at different speeds is observed, then the bowl is removed and the strainer, grater, and sealing rings are inspected for wear. The board and contacts are checked for oxidation and signs of overheating, and the lid lock sensor is tested for activation when closing. Based on the inspection, our technician lists what has failed and which Bork juicer parts need replacement. The cost is given after diagnostics because before disassembly it's impossible to see which component has failed — this way the client pays for actual work, not a guess. If repairs aren't advisable, we'll tell you right on the spot.

What to check yourself before calling a technician

  • Bowl lid: make sure the latch is fully engaged and the sensor detects closure.
  • Filter mesh: check that the strainer holes aren't clogged with pulp and fibers.
  • Thermal protection: let the appliance cool down after overload and try starting it again.
  • Power and outlet: check the outlet contact and that the cord isn't damaged.
  • Behavior on startup: listen for the motor humming without the disc rotating.
  • False alarm: if the appliance works normally after cooling and cleaning, the cause was overload, not a breakdown.

Warranty and why you should trust Bork juicer repair to a direct contractor

Warranty and a direct contractor are what set proper service apart from a one-time fix. We explain what responsibility we take on and why it matters who holds the tools.

What warranty is provided for Bork juicer repair

We provide a 1-year warranty on labor and parts for Bork juicer repairs — it covers both on-site visits and in-shop work. The year covers both the technician's labor and the installed component: a replaced seal, a new drive shaft, or a bowl gasket. The terms don't change with location — whether at the customer's kitchen or in our workshop, the duration and scope of the obligation are the same. A warranty on parts means that if the replaced component fails again, the labor and the part are covered under one obligation, not split into "this is the part" and "this is the technician." In my view, this is exactly the clause owners most often check when choosing a service — and rightly so: a vague statement about labor-only obligations is worthless. Ask whether the part itself is included in the coverage — that's the first thing to clarify before work begins.

Why a direct provider, not an aggregator

Tech Service is a direct provider: your Bork juicer is serviced by our own specialist, not an intermediary who forwards the request to a third party, so we are responsible for the work and the warranty. Our technicians have between 4 and 20 years of experience, and the same person who visits your home also handles the warranty follow-up. When working through an intermediary, it's harder to verify the terms and the quality of parts, whereas with a direct provider, the person who disassembled the equipment is personally accountable for the result — and if the bowl joint leaks again after service, the same service returns under warranty. For the owner, this means you won't have to re-explain the nature of the fault or figure out who installed the seals and gaskets. In our practice, a repeat warranty visit takes less time than the initial diagnosis — the technician already knows the specific machine and its weak points.

How to approach Bork juicer repair

Analyzing symptoms, error codes, and typical failures brings the owner to one decision: repair the Bork juicer or replace it. Below is a brief summary of what to look for when choosing a technician and what to expect from the service.

  • A symptom doesn't name the part: a leak at the joint, humming, and wet pulp point to different components, and they are checked one by one.
  • The juicing type changes the list of works: centrifugal and auger models fail differently, so the list of operations depends on the design, not just the brand.
  • A code on the display is not a diagnosis: an error signals that protection has tripped or there's an electronics fault; it is always checked against how the components behave under load.
  • Free diagnostics before work begins and a warranty on labor and parts — these are the terms to rely on when choosing a provider.
  • Some checks are within the owner's ability: inspecting the seal, lid, and bowl, but a recurring fault requires disassembly and component inspection.

34brands

Besides Bork, we repair other juicer brands in Almaty

We service Bork juicers and other brands that have dedicated pages on the site.

We also repairWe also repairTECH SERVICE09

Besides Bork juicer repair, we fix other equipment in Almaty

Tech Service technicians repair other appliances too — with the same 1-year warranty on labour and parts.

BlogBlogTECH SERVICE10

Worth reading before Bork juicer repair in Almaty

Leave a review

Choose a platform — the TECH SERVICE page will open.

2ГИС2GISGoogle MapsЯYandex Maps
Send a review with photos on WhatsApp