experience9 yearsRuslan Ts.
Washing machine and refrigerator repair technician
City
Language
What broke
Sections
Message on WhatsApp+7 (775) 030 02 94Mon–Fri 10:00–19:00, Sat–Sun 11:00–18:00
A technician arrives within 60 minutes anywhere in the city. Free diagnostics.
Our own technicians4 to 20 years of experience




Repair prices
The most frequent symptoms and likely causes. The technician will pinpoint the exact cause after diagnostics.
No power or filter failure
from8 000 ₸
Heating element burned out
from7 000 ₸
Damaged ribbon cable or board failure
from7 500 ₸
Heating element insulation breakdown or moisture
from8 000 ₸
Temperature sensor failure
from5 500 ₸
Overheating or temperature sensor failure
from5 500 ₸
Mechanical damage
from13 000 ₸
Cooling fan wear
from7 000 ₸
The table lists the 'from' price for labor, for common jobs also the 'from' price of the part, plus the time required to complete the job.
1 visittime
from 5 500 ₸cost

BeforeAfter5 steps

From request to performance check — five steps.
Submit a request, specify the model and symptom. The technician will arrange a convenient time.
The technician arrives anywhere in the city within 60 minutes after confirmation.
The technician will agree on the scope of work and cost before starting the repair.
After the cost is approved, the technician performs the repair and replaces parts.
Turn on the cooktop and check all burners and modes after reassembly.
The home appliance repair department in Almaty has 8 technicians with 8 to 12 years of experience.

The department has 8 specializations — they are listed on the technicians' cards.
experience9 yearsWashing machine and refrigerator repair technician
experience12 yearsGeneral household appliance repair technician
experience10 yearsField technician for washing machine and refrigerator repair
experience8 yearsExpert washing machine repair technician
experience8 yearsField refrigerator repair technician
experience8 yearsSenior washing machine repair technician
experience11 yearsDishwasher repair technician
experience9 yearsWashing machine repair technician
We reply during working hours
Submit a request with the cooktop model and the fault symptom. The technician will arrange a convenient time and come for diagnostics.

Warranty question? Call us
+7 (775) 030 02 947 898 reviews of repairs at TECH SERVICE in total
Данияр С.Order No. 2026-1913 · 9 February 2026
oursПозвонил знакомому, он раньше работал в сервисе, посоветовал этих. Была паника, если честно. Проблема — ошибка. Заявку приняли по телефону, перезвонили через десять минут. Нужна была замена: индукционная катушка. Вышло 22 500 тенге, дешевле, чем я рассчитывал. В тех сервис привёл знакомый, у него тут чинили ноут. Шум пропал, работает мягко)
Нурлан Б.Order No. 51212 · 30 May 2025
oursЦена имела значение, но и горонтия тоже. Повод для визита: не включается. Крутит ровно, без рывков.
Елена К.Order No. 56013 · 15 March 2022
oursУтром работало, днём сломалось, вечером я уже искал сервис. Симптом был очевидный: ошибка. Радик Т возился с этим дольше, чем планировал, но довёл до конца. Назвали 26 500 сразу, в конце сумма не изменилась. Ребёнок уже проверил на прочность, держится.
Гаухар Н.Order No. ZK-2783 · 28 December 2020
oursРадик Т честно сказал, что менять, а что ещё походит. Под замену пошло: индукционая катушка. С тех пор ни разу не подвёл.
Сауле Н.Order No. 23570 · 14 March 2020
oursДруг посоветовал, у него похожая история была. Не думал, что вообще напишу отзыв, но тут стоит. Первое, что заметил: не включается. Радик Т возился с этим дольше, чем планировал, но довёл до конца. Договорились на утро, к девяти уже был свободный мастер. Смета совпала с итогом, что редкость. В techservice попал случайно — и остался. Проверили на всех режимах, всё чётко.
Аружан К.Order No. ZK-6836 · 15 January 2020
oursТехника на гарантии уже не была, так что выбор был свободный. Жалоба простая: не греет зона. Проверили на всех режимах, всё чётко.
Светлана Д.Order No. 92173 · 14 March 2019
oursЖалоба простая: не включается. Дамир М не стал навязывать дорогую запчасть, поставил нормальную. Ребёнок уже проверил на прочность, держится)
Асель Ж.Order No. TS-5830 · 27 December 2018
oursОсновная жалоба — ошибка. Радик Т честно сказал, что менять, а что ещё походит. Ребёнок уже проверил на прочность, держится.
Ксения И.Order No. TS-1706-825 · 9 December 2017
oursОсновная жалоба — не включаеться. Дамир М снял деталь, показал износ, вопросов не осталось. Техсервис в Алматы, если что, вот их адрес — не пожалел. Второй месяц — полёт нормальный)
Сауле Н.Order No. 2017-5191 · 6 July 2017
oursДамир М принял, посмотрел и сразу сказал, что делать. Внешне как новый, если не считать мелкой царапины
Didn’t find the answer? Message us on WhatsApp.
Ask a questionIt depends on the model: on some Korting cooktops the glass-ceramic is replaced separately from the body, while on others it comes as one unit with the frame and touch sensor. A technician will determine during diagnostics what exactly needs to be replaced in your case.
Most often the issue is in the zone itself: the induction coil, sensor, or board contact for that burner is damaged. Less commonly, the cause is cookware with a thin or uneven bottom—test it on a working zone before calling a technician.
Yes, in most cases the sensor can be repaired: the technician dries and cleans the board, checks the traces, and replaces the touch panel if necessary. Glass replacement is only needed if moisture got under it and damaged the coating.
Yes, this indicates current leakage or a short circuit, and it's best to cut power to the cooktop until it's repaired. Continuing to use it can damage the wiring and create a fire risk, so call a technician right away.
Our technicians work with various brands, including Korting, and know the specifics of its induction and glass-ceramic cooktops. A staff member from Tech Service comes to your home, not a middleman, and diagnostics are free.
Each model has its own set of codes, and it's impossible to name the exact code from one symptom—it depends on the model. This behavior usually indicates overheating, a sensor or board failure, and the technician will read the code on site during diagnostics.
Tech Service repairs Korting cooktops in Almaty: our technician comes to your home or the cooktop is repaired at our service center. Diagnostics are free, visits within 60 minutes across the city, and a 1-year warranty on labor and parts. Technicians with 4 to 20 years of experience handle induction, electric, and combined Korting cooktops.
Korting owners often prefer not to replace their appliances even after a breakdown — they are repairable, and the work is done by a direct contractor with their own technicians, without passing the request to a third party.
We service induction, electric, and combined Korting cooktops with glass-ceramic surfaces and touch controls. Induction models are recognized by the coils under the glass and the characteristic hum when turned on; electric ones run on heating elements; combined models combine both groups of zones in one frame. The touch control unit in all three types follows the same logic: a board with capacitive buttons, a ribbon cable, and a power module that switches the load. Using the label on the bottom or back, the technician checks the series and selects the testing scheme for the specific model. The cooktop type determines the set of components the technician checks: for induction, it's the inductor and IGBT power transistors; for electric, the heating element and zone relay; for combined, both groups, so diagnostics start with confirming the model.
Our staff technician with 4 to 20 years of experience comes to you, not a dispatcher from an aggregator who forwards the request to a third party. Such an employee knows the logic of Korting boards: how the controller behaves during overheating, why the touch sensor triggers intermittently due to a dirty ribbon cable, and which codes on the display relate to the power section and which to the sensors. Diagnostics are free, so the visit doesn't turn into an attempt to recoup costs at any price — components are checked in order, and you see exactly what has failed. A direct contractor is fully responsible for the result: if the cooktop malfunctions again after the work, the same service will deal with it, not a reseller of the request, so the warranty on labor and parts holds up in practice.
We break down Korting failures by component — from the inductor to the glass-ceramic — so you can match the symptom to your cooktop and understand what the technician will check.
If a Korting cooktop won't turn on or trips the breaker when turned on, we first check the wiring and the breaker, then the control board and the varistor overvoltage protection. In our experience, the control board fails after power surges: a burnt varistor is visible, and broken traces can be tested with a multimeter. The breaker in the panel trips when the total load on the line exceeds the rating or when the trip mechanism inside the breaker itself has worn out. We check the wiring for heated terminals and melted insulation at the outlet — a weak contact causes voltage drop under load. A tripped breaker doesn't always mean a cooktop failure: the cause can be an overloaded line or a faulty breaker itself, so the technician separates these scenarios before disassembling the cooktop.
When a Korting induction hob doesn't detect cookware or one zone won't heat, we check that zone's inductor, the data ribbon between the boards, and the NTC temperature sensor. The inductor transfers heat to the cookware via a magnetic field, and if the coil breaks or the IGBT module fails, the zone stops working even though the neighboring ones work fine. The ribbon between the power and control boards eventually oxidizes from steam and grease—contact is lost, and the board doesn't receive the temperature signal. The NTC sensor reads too low or too high, causing the electronics to block heating. Before calling a technician, try moving the pot to a neighboring zone and using cookware with a ferromagnetic base—if the problem goes away, it's the cookware, not the hob.
On Korting hobs, we replace the glass-ceramic when it cracks and restore touch controls if the slider doesn't respond to touch or triggers on its own. Glass-ceramic cracks from sudden temperature changes, impact from cookware, or overheating a zone without a pot. The touch slider loses sensitivity when moisture gets on the touch board or the conductive layer under the glass wears off, and false triggers are caused by a stuck button. We check the touch board for oxidation and microcracks in the solder joints, and replace the module entirely if needed. A crack is dangerous not just visually: moisture gets through it onto the touch board and causes false triggers, so don't delay replacing the glass even if the hob still works—otherwise moisture will reach the electronics and add touch sensor repair to the glass replacement.
| Symptom | What we check | Hob type |
|---|---|---|
| Won't turn on | Control board, varistor, wiring | All types |
| Trips the breaker | Wiring, breaker, varistor protection | All types |
| Doesn't detect cookware | Inductor, ribbon, NTC sensor | Induction |
| One zone won't heat | Inductor or zone relay | Induction, electric |
| Touch controls unresponsive | Touch board, slider | All types |
| Cracked glass | Glass-ceramic, touch board | All types |
| Turns off after a few minutes | Cooling fan, NTC sensor | Induction |
A code on the Korting display is a hint about which component has failed. Here's what typical error groups mean and how a technician clears them after fixing the cause.
The combination of symbols on a Korting hob points to a group of components—power supply, inductor, temperature sensor, or touch controls—and we decode it based on the hob model, not a generic list. Induction series and glass-ceramic models use different control boards, so the same combination leads to different chains: on induction, power switches and the coil are checked more often; on glass-ceramic, the NTC sensor and heating relay. Touch faults are often related to the ribbon or moisture under the glass. The same code on different Korting series may refer to different components, so when you request service, provide the model from the nameplate on the body—this speeds up diagnostics.
If the Korting panel shows an error and shuts off after a few minutes of operation, we check the inverter cooling fan and the NTC temperature sensor — most often the overheat protection is triggering. The inverter in the induction zone generates heat during operation, and its power components are cooled by a separate fan; when airflow drops, the board detects the temperature rise and shuts off the burner before the switch burns out. The NTC sensor may also give high readings due to oxidized contacts or displacement from its seat. This scenario doesn't always mean electronics failure: a fan clogged with dust or blocked airflow under the countertop produces the same effect, and cleaning the cooling channels gets the panel working again — without replacing the board.
We outline the workflow from request to post-service check, including when the unit needs to be removed from the countertop and when work is done in place.
After your request, a technician arrives within 60 minutes, performs free diagnostics, and quotes the repair cost before starting work. On-site diagnostics begins with questions about the symptoms: how the appliance behaves when turned on, which zone fails to heat, whether the error repeats on the display. Then the technician opens the bottom of the unit, inspects the control board, tests power components, and checks the touch sensor response on each segment. You get specifics: which component failed, what needs replacing, and how long it will take. Diagnostics is free whether or not you agree to the repair, so you decide without pressure and without paying for the visit itself.
Some Korting repairs are done on-site without removal, but for control board soldering or glass-ceramic replacement, the unit is taken out of the countertop and, if needed, brought to the service center. On-site we replace zone relays, sensors, the cooling fan, and restore power contacts — anything accessible from below without disassembling the cooktop. Glass replacement and board trace soldering require a horizontal position and a clean workbench, so those tasks are done in the workshop. Before the visit, we confirm the model and appliance type so the technician brings the right tools and fasteners. A built-in panel is attached to the countertop from underneath, so access from below is needed — if there's a cabinet with shelves under it, clear it before the visit to save time.
We explain the warranty on Korting repairs, safety before the technician arrives, and the criteria for deciding whether to repair the cooktop or replace it with a new one.
We provide a 1-year warranty on labor and parts, and it covers Korting cooktop repairs just like any other appliance. Technicians with 4 to 20 years of experience install parts matched to the specific component: control board, touch membrane, inductor, or glass-ceramic surface. Diagnostics before any work is free, so warranty cases are confirmed during inspection, not based on the owner's description. This warranty covers both the part itself and the quality of its installation — if a component fails due to our work, the repeat repair is covered. A warranty only makes sense when it's given by the person who did the work: with a direct contractor, claims are handled within the service, without passing between subcontractors.
Whether to repair or replace a Korting cooktop depends on the component: replacing the glass-ceramic, touch sensor, or board is usually justified, but several burned-out induction zones at once may tip the decision toward a new cooktop. The control board in these models runs the heating zones and the touch sensor, so its failure affects the entire surface, while a crack in the glass-ceramic affects only one area. The inductor is replaced separately, restoring a specific zone without touching the others. Consider not only the breakdown but also the age of the appliance: if the repair brings the cooking surface back for years to come, it makes sense, but if components fail one after another, a new model may be the smarter choice. The technician quotes the price after free diagnostics, when the full list of faults is clear.
Repairing a Korting cooktop in Almaty usually means restoring one component rather than replacing the whole appliance. Below is a quick summary to help you decide before calling a technician.
24brands
We repair appliances from various brands. Choose a brand to learn more.
Tech Service technicians repair other appliances too — with the same 1-year warranty on labour and parts.
Refrigerator Repair in Almatyfrom 3 000 ₸
Washing Machine Repair in Almatyfrom 3 000 ₸
Dishwasher Repair in Almatyfrom 3 500 ₸
Oven Repair in Almatyfrom 3 000 ₸
Cooktop Repair in Almatyfrom 3 500 ₸
Air Conditioner Repair in Almatyfrom 3 500 ₸
Boiler and Water Heater Repair in Almatyfrom 2 500 ₸
Freezer Repair in Almatyfrom 6 000 ₸
Tumble Dryer Repair in Almatyfrom 5 000 ₸
Coffee Machine Repair in Almatyfrom 2 500 ₸
Robot Vacuum Cleaner Repair in Almatyfrom 3 500 ₸
Vacuum Cleaner Repair in Almatyfrom 1 500 ₸
Microwave Oven Repair in Almatyfrom 2 000 ₸
Hair Dryer Repair in Almatyfrom 1 500 ₸
Iron Repair in Almatyfrom 3 000 ₸
Electric Kettle Repair in Almatyfrom 2 500 ₸
Mixer Repair in Almatyfrom 2 500 ₸
Multicooker Repair in Almatyfrom 500 ₸
If your oven isn't working, first check the outlet, the circuit breaker in the panel, and the selected mode, then assess the symptom: not heating…
3 October 2025 · 12 minutes read
If your dishwasher won't drain, the most common culprits are a clogged filter or drain hose; less often, it's the pump, impeller…
24 March 2026 · 12 minutes read
A washing machine can hum for many reasons, and the first thing to figure out is when the sound appears.
20 March 2026 · 12 minutes read
If your washing machine isn't filling with water, the most common culprits are a closed valve, a clogged inlet filter screen on the hose…
20 February 2026 · 13 minutes read
If your microwave isn't heating but the light and turntable still work, the problem is usually one of the high-voltage components — the magnetron, diode…
15 February 2026 · 12 minutes read
If your refrigerator stops working, first check the outlet, the power cord, and the thermostat setting, and after defrosting let it stand for a while.
4 February 2026 · 12 minutes read












