Open until 19:00+7 (775) 030 02 94Call a technician
Tech Service technician next to a gas boiler

Rinnai Gas Boiler Repair in Almaty

A technician arrives within 60 minutes anywhere in the city. Free diagnostics.

  • 1-year warranty
  • 4 to 20 years of experience
  • You can pay via Kaspi QR, Kaspi Red, bank card, cash, or bank transfer for companies

Our own technicians4 to 20 years of experience

Ruslan Ts.Damir M.Dilmurat S.Dima

Repair prices

  • Diagnostics0 ₸
  • Fan replacementfrom5 500 ₸
  • Temperature sensor replacementfrom6 000 ₸
  • Control board replacementfrom6 000 ₸
  • Gas valve replacementfrom7 000 ₸
All prices
2ГИСЯours4,96 064 reviews
2GIS · Yandex · order database
Common faultsCommon faultsTECH SERVICE02

Common Rinnai gas boiler faults in Almaty

Below are typical symptoms and likely causes that the technician checks on site.

PricesPricesTECH SERVICE03

How much Rinnai gas boiler repair costs in Almaty

The table lists the 'from' price for labor, for common jobs also the 'from' price of the part, plus the time required to complete the job.

Fan replacementparts not included

1–2 hours

from5 500 ₸

Temperature sensor replacementparts not included

1–2 hours

from6 000 ₸

Control board replacementparts not included

1–2 days

from6 000 ₸

Gas valve replacementparts not included

1–2 hours

from7 000 ₸

Three-way valve repairparts not included

1–2 hours

from7 500 ₸

Before and afterBefore and afterTECH SERVICE04

Before and after Rinnai gas boiler repair in Almaty

Hot water barely warm, radiators heating

1 visittime

from 7 500 ₸cost

Problem
On the Rinnai gas boiler, when the hot water tap was open, the water ran barely warm, while the radiators kept heating.
What we did
The technician removed the front cover and checked the three-way valve in the hydraulic unit at the bottom of the boiler: the actuator was not switching the stem, the stem was stuck; replaced the actuator, worked the stem loose and resealed it.
Result
Hot water ran normally, the radiators stopped heating when the tap was open; the technician checked the heating/hot water switching.
I want the same
Baxi gas boiler: hot water barely warm, radiators heating — after repairBeforeAfter
01 / 04
All repairs
TECH SERVICE mobile technician with a tool case

How Rinnai gas boiler repair works at your home in Almaty

Five steps from your request to checking the boiler after repair.

  1. Requestright away

    Describe the symptoms by phone or message so the technician brings the right tools.

  2. Technician visitwithin 60 minutes

    The technician comes anywhere in the city and inspects the boiler on site.

  3. Preparing accessbefore the visit

    We'll agree on a visit time: clear some space around the boiler and make sure the gas valve is accessible.

  4. Repairby appointment

    Work is carried out after we agree on it with you.

  5. Sharing the error codebefore the visit

    Tell us the error code and symptoms in advance so the technician brings the right parts.

Leave a request
TechniciansTechniciansTECH SERVICE05

Our home appliance repair technicians in Almaty

The home appliance repair department in Almaty has 8 technicians with 8 to 12 years of experience.

  • 8 technicians in Almaty
  • 8–12 years of experience in the department
  • Article author Ruslan Ts., 9 years of experience
Technician repairing a gas boiler at a customer’s home
Field technician at a customer’s home

The department has 8 specializations — they are listed on the technicians' cards.

01 / 08
Ruslan Ts., washing machine and refrigerator repair technicianexperience9 years

Ruslan Ts.

Washing machine and refrigerator repair technician

Damir M., general household appliance repair technicianexperience12 years

Damir M.

General household appliance repair technician

Dilmurat S., field technician for washing machine and refrigerator repairexperience10 years

Dilmurat S.

Field technician for washing machine and refrigerator repair

Dima, expert washing machine repair technicianexperience8 years

Dima

Expert washing machine repair technician

Nikita M., field refrigerator repair technicianexperience8 years

Nikita M.

Field refrigerator repair technician

Oraz, senior washing machine repair technicianexperience8 years

Oraz

Senior washing machine repair technician

Radik T., dishwasher repair technicianexperience11 years

Radik T.

Dishwasher repair technician

Rustem T., washing machine repair technicianexperience9 years

Rustem T.

Washing machine repair technician

We reply during working hours

Book Rinnai gas boiler repair in Almaty

Describe the fault and your boiler model — the technician will arrange a convenient visit time. Diagnostics are free, and there's a 1-year warranty on labor and parts. You can pay via Kaspi QR, Kaspi Red, bank card, cash, or bank transfer for companies.

TECH SERVICE administrator replying to a customer's WhatsApp message

Warranty question? Call us

+7 (775) 030 02 94
Customer reviewsReviewsTECH SERVICE06

Reviews of Rinnai gas boiler repair in Almaty

Эльмира Т.Order No. TS-3700 · 31 October 2025

ours

Симптом был очевидный: не зажигаеться. Проверили при мне, показали, что всё держит.

Repair: gas boiler repair in

Александра Н.Order No. ZK-2025/532 · 2 September 2025

ours

Құрылғы ескі болғандықтан, бөлшек табыла ма деп қорықтым. Күтуге уақытым жоқ еді, сол күні алып кеттім)

Repair: gas boiler repair in

Владимир Н.Order No. 84104 · 6 May 2023

ours

Друг посоветовал, у него похожая история была. Честно, уже готовился покупать новое, но обошлось. Повод для визита: не греет воду. Никита М помог выбрать, без навязывания. Запчасть была в наличии, доплачивать не пришлось. Приехал без записи, приняли как есть. Под замену пошло: мембрана. В помещении тесновато, но это мелочи. Работает даже тише, чем до поломки

Repair: gas boiler repair in

Мирас С.Order No. ZK-5244 · 24 November 2022

ours

Техника на гарантии уже не была, так что выбор был свободный. Вернули в тот же день, всё функционирует

Repair: gas boiler repair in

Игорь Щ.Order No. ZK-2022/184 · 8 June 2022

ours

До этого обращался в другой сервис, там только развели руками. Честно, уже готовился покупать новое, но обошлось. С чем пришёл: течёт. Могли бы взять больше, но взяли по-божески. В списке работ — мембрана. Созвонились, договорились на удобное время, никто не тянул. Хороший сервис, побольше бы таких. Гудит ровно, не грееться, всё как надо.

Repair: gas boiler repair in

Айнур М.Order No. 2022-1316 · 28 April 2022

ours

Долго откладывал ремонт, потом всё-таки собрался. Долго искал, кому это отдать, и вот нашёл. Жалоба простая: течёт. Поменяли: насос. Заявку приняли по телефону, перезвонили через десять минут. Проверил дома — всё на месте, ничего не забыли

Repair: gas boiler repair in

Ержан А.Order No. 14877 · 22 August 2021

ours

Симптом был очевидный: не греет. Никита М приехал в тот же день, хотя был конец смены. Работает даже тише, чем до поломки.

Repair: gas boiler repair in

Сабина Г.Order No. ZK-7520 · 4 October 2020

ours

Техниканы жөндеуге алып келу үшін арнайы уақыт бөлдім. Техника кенеттен істен шықты, қатты асығыс едім. Достарыма да айттым.

Repair: gas boiler repair in

Виктор Ф.Order No. 2020-4309 · 31 May 2020

ours

Симптом был очевидный: течёт. Отдельно спосибо мастеру — Никита М, терпения ему хватило. Пользуюсь ежедневно, вопросов нет.

Repair: gas boiler repair in

Вероника П.Order No. 2019-7397 · 21 July 2019

ours

Больше всего напрягало: не греет воду. Дамир М возился с этим дольше, чем планировал, но довёл до конца. Сказать, что доволен — ничего не сказать.

Repair: gas boiler repair in
See all reviews
Questions and answersQuestionsTECH SERVICE07

Questions about Rinnai gas boiler repair in Almaty

Didn’t find the answer? Message us on WhatsApp.

Ask a question
What pressure should the expansion tank of a Rinnai boiler have?

Typically, the pressure in a Rinnai expansion tank should match the heating system pressure and be around 1–1.5 bar, but the exact value depends on the model. You can only check and top up the tank with the water drained from the boiler, so it's best to leave this to a technician.

Why does the pressure in a Rinnai boiler drop if there's no leak?

If there's no visible leak, the pressure may drop due to a faulty expansion tank, air in the system, or release through the safety valve. A technician will check these components during free diagnostics and identify the cause.

How do I increase the pressure in a Rinnai boiler?

Pressure is increased through the fill valve, opening it until the gauge reaches the required mark, usually around 1–1.5 bar. If the water doesn't hold or the pressure rises too quickly, you need a technician: the cause is in the tank or valve.

Can a Rinnai boiler circuit board be repaired or does it have to be replaced?

It depends on the type of damage: some Rinnai board faults can be fixed by repair, but if the traces are burned or the controller is flooded, replacement is needed. The technician makes the decision after free diagnostics.

How can you tell a faulty three-way valve from a clogged secondary heat exchanger in a Rinnai?

When the secondary heat exchanger is clogged, the boiler heats the heating system but produces hot water poorly, while a three-way valve more often jams and fails to switch the circuit. An accurate conclusion comes from disassembling the unit during diagnostics.

What should I do if a Rinnai boiler won't turn on after a power surge?

Most likely, the control board or fuses are damaged, so you shouldn't turn the boiler on again. A technician will check the electronics on site and tell you whether the board needs repair or replacement.

Repair guideArticleTECH SERVICE08

Rinnai gas boiler repair in Almaty with technician visit

Author: TECH SERVICE editorial team

Published
Updated

Tech Service repairs Rinnai gas boilers in Almaty with its own technicians who have 4 to 20 years of experience. A technician arrives at your home within 60 minutes anywhere in the city, diagnostics are free, and the cost of work is quoted after diagnostics. We provide a 1-year warranty on labor and parts.

Rinnai error codes and what they mean

The code on the display is a starting point, not a ready diagnosis. We explain how a technician reads the Rinnai control system's hint, what they check first, and the order they follow along the chain.

What the error code on the Rinnai display means

  • Meaning of the hint: the number on the screen shows the component or safety function that triggered the Rinnai boiler's control system.
  • One cause does not equal one code: the same number can be caused by several faults — from a dirty sensor to a pressure drop.
  • Symptom next to the number: the technician matches the code with the boiler's behavior — noise, failure to ignite, temperature fluctuations.
  • When it appears: triggering at startup, during heating, or when switching to hot water narrows down the checks.
  • Electronics and hydraulics: some codes relate to electronics, others to the circuit and sensors.
  • Recording observations: note the number, when it appeared, and the boiler's behavior before that — this speeds up troubleshooting.
  • Sequence: first we check the chain 'code → component → cause', not replace the first part we come across.

Boiler clicks but doesn't ignite — what to check

Clicks without ignition are more often related to the flame sensor, gas valve, or gas supply, not the board as a whole. The ionization sensor confirms the presence of flame during ignition: if there's no response, the control system shuts the valve and blocks the burner. The gas valve is checked for opening and actual gas flow to the burner, and the supply — by the valve and pressure stability in the line. The control board is last in this chain: first the sensor, valve, and gas are ruled out, and only then the electronics are checked. If the clicks are rhythmic and repeat in cycles, this is a standard ignition attempt with blocking — you shouldn't disassemble the boiler yourself before the technician arrives. On models with flame modulation, the rhythm of clicks matches ignition attempts, and the technician uses it to distinguish a supply problem from an ionization failure.

Which Rinnai codes are most common and what they mean

Signal groupWhat it indicatesWhat we check first
Ignition and flameno flame confirmationflame sensor, gas valve
Draft and fanflue gas exhaust disruptedflue fan, pressure switch
Circuit pressurepressure drop or fluctuationsexpansion tank, leaks
Overheatsafety triggeredcirculation, NTC sensor

Typical Rinnai breakdowns by component

We go through the most common Rinnai scenarios — from 'no hot water' to pressure drop — and show which component is responsible.

No hot water while heating works

If the heating works but the tap water is cold, we first check the three-way valve and the secondary heat exchanger on Rinnai. The valve switches flow between the heating circuit and the hot water circuit: when the stem seizes, heat goes only to the radiators and the tap stays cold. The secondary heat exchanger becomes clogged with scale over time — in Almaty water, hardness salts deposit on the plates, and the heat carrier heats water worse and worse until heating stops completely. In my experience, these two causes produce almost the same symptom, but cleaning the heat exchanger and replacing the valve are different jobs with different results. A clogged secondary heat exchanger and a seized valve give a similar symptom but are treated differently — so it's important to tell one from the other before replacing parts.

Why pressure drops and the boiler turns on frequently

  • Expansion tank: absorbs pressure fluctuations in the circuit, and when the air chamber loses pressure, the gauge needle drops.
  • Leak in the circuit: a loose connection or a leak in the heat exchanger lowers pressure, and the boiler needs topping up.
  • NTC temperature sensor: when it fails, it distorts readings, and the burner fires more often than needed.
  • Circulation pump: a clogged impeller reduces flow, causing the Rinnai to run erratically — short cycling.
  • Air in the system: an air lock blocks circulation, pressure fluctuates, and the burner won't settle into a stable mode.
  • Frequent topping up: if you have to add water constantly, the problem isn't the water itself — look for a leak in the unit.

Board after a voltage spike — repair or replace

After a voltage spike, we first diagnose the Rinnai board — some failures can be fixed by repair rather than replacing the whole unit. The control board manages ignition, the burner, and the pump: during a power surge, individual power components or the control section can burn out, and the boiler stops starting without an obvious code on the display. During diagnostics, the technician tests the circuit and identifies exactly what's damaged — sometimes replacing one component is enough, sometimes a new unit is needed. We also check the stabilizer and grounding separately: without them, a new board will fail at the next surge as quickly as the old one. The solution depends on the type of damage: sometimes one power element is affected, sometimes the control section; the technician determines this during diagnostics, not just from the symptom 'won't turn on'.

Rinnai models and differences in repair

The approach depends on which Rinnai you have — a wall-mounted combi, a single-circuit, or a floor-standing model. Here's how the components, typical operations, and working conditions differ for the technician.

How servicing differs for wall-mounted and floor-standing Rinnai

  • Wall-mounted combi: tight layout of components and electronics, frequent attention points — the three-way valve and secondary heat exchanger.
  • Wall-mounted single-circuit: same control board, but simpler hydraulics — fewer parts for water heating.
  • Floor-standing: more hydraulics and mechanics, a larger burner and cast-iron heat exchanger, less electronics.
  • Access to components: on wall-mounted units, work is done through the removable casing; on floor-standing, through the top and side panels.
  • Typical work: wall-mounted units more often need secondary circuit cleaning; floor-standing need burner servicing.
  • Our experience: we service both groups in the workshop and on-site, and tailor the set of operations to the design.

Which Rinnai models come in for service most often

Based on our call-outs, most requests are for wall-mounted combi Rinnai models in the RB, RUS, and MCF series — they're installed more widely and work harder for hot water supply. The Rinnai secondary heat exchanger is responsible for heating water and takes the load first: in hard water, scale builds up on the walls, heat transfer drops, and the plates eventually clog. On RB and RUS series, this shows up as reduced hot water flow when heating is running; on MCF, the board is also sensitive to voltage spikes. During a visit, the technician checks the series on the nameplate to select the right parts and avoid disassembling unnecessary components. Moreover, the frequency of breakdowns depends not so much on the series as on water quality and regular maintenance — the same component wears differently at different sites.

Servicing in apartments and private houses

We service Rinnai in both apartments and private houses — the technician comes on-site, and if needed, work is done in the workshop. The mobile technician travels throughout the city: in an apartment, they work at the boiler, and if disassembly or soldering is required, they take the part to the workshop. In apartments, space for disassembly is often limited — the boiler is in a kitchen niche or hallway, and it's important not to disturb neighbors with noisy work. In a private house, the boiler is connected to piping, so the technician also checks that — the expansion tank and inlet filters. In my opinion, homeowners should check filter condition and system pressure before calling a technician — this narrows down the causes and saves diagnostic time.

How diagnostics and repair work

Here's the path from request to final check: what the technician does at each step, how the scope of work is agreed, and when you learn the cost.

What's included in free Rinnai diagnostics

  • Checking the control system: we inspect the board, sensors, and ignition, and compare readings with the code on the display.
  • Checking the hydraulics: we inspect the heat exchanger, circulation pump, three-way valve, and safety group.
  • Reading codes: we match the error to the symptom — clicking, weak flow, pressure drop.
  • Finding the cause: we confirm the fault on site, not from a single symptom.
  • Agreeing the scope: you see which component needs replacement and which is working.
  • Cost after diagnostics: we quote the price once the cause is identified.

How to call a technician and how soon they arrive

Our technician arrives at your home within 60 minutes anywhere in the city, and work can be done both on site and at the service center. We take requests by phone: you describe the symptom, the code on the display, and the boiler model — wall-mounted or floor-standing Rinnai. The technician brings tools for the specified model and agrees the scope of work after on-site diagnostics. If the fault requires checking the board or a component at the service center, the technician will agree on that format with you. Diagnostics remain free — you pay only for the agreed work. We repair Rinnai gas boilers in Almaty both at your home and at the service center, so we choose the right format based on the nature of the fault. In my experience, a precise description of the symptom when you call saves a whole repeat visit: the more specifically you name the code and the boiler's behavior, the faster we can prepare the needed part.

Work sequence and final check

  • Request: you describe the symptom and the code on the display, and the technician clarifies details about the model.
  • Visit: the technician arrives at your home within 60 minutes anywhere in the city.
  • Diagnostics: we check the control system and hydraulics for free and confirm the cause.
  • Agreement: we quote the price after diagnostics, and the scope is fixed before work begins.
  • Repair: we replace components and parts according to the agreed scope, with no unnecessary replacements.
  • Check: we test heating and hot water before handing over, checking both circuits.
  • Warranty: we provide a 1-year warranty on labor and parts.

Warranty and terms of service

We explain exactly what our warranty covers, why the work is done by a direct contractor, and what terms apply when we visit your Rinnai boiler.

What the 1-year warranty covers

  • Term and object: we provide a 1-year warranty on labor and parts — both for on-site service and for work at the service center.
  • Replacement of components: the warranty covers installed parts — board, valve, sensor, heat exchanger, or pump.
  • Repeat request: if the symptom returns, the technician compares it with the work performed and checks the specific component rather than starting from scratch.
  • Boundaries: the warranty applies specifically to the work performed and the parts supplied, not to the entire boiler.
  • What this gives you: if the symptom returns, the technician matches the request with the record and checks the specific component rather than starting diagnostics from scratch.
  • Our approach: we handle each request individually for the component that was replaced — that way the cause is found faster.

Direct contractor and payment

Tech Service is a direct contractor: the work is done by our technician, not an intermediary, and you can pay via Kaspi QR, Kaspi Red, bank card, cash, or bank transfer for companies. Your request doesn't go to a third party: the technician who comes to you is responsible for both the work and the warranty on it. This distinguishes a direct contractor from a scheme where a dispatcher passes the call to a subcontractor and quality depends on who ultimately takes the job. We accept payment in cash, by card, and by transfer — you choose the method. The price is quoted after free diagnostics, when it's clear which component needs attention. From experience, the direct scheme saves time on approvals: you don't have to wait for an intermediary to pass the request along and come back with an answer — one person handles your request from the visit to the final check.

Technician experience and service area

Our technicians have 4 to 20 years of experience and cover the whole city, including apartments and private homes. Travel takes 60 minutes — the specialist comes to your door or takes the unit to the service center if on-site work isn't possible. Rinnai experience shows in diagnostics: they can tell a clogged heat exchanger from a worn valve faster and don't replace parts unnecessarily. In my view, that's what sets someone with experience on a specific brand apart from a generalist — they know which components on this equipment fail more often and where to focus the check first. Diagnostics are free, so you can start the check with no obligation, and you decide on replacing a part only after the technician names the cause and scope of work.

Rinnai maintenance and prevention

We break down what Rinnai gas boiler maintenance includes and how prevention reduces the risk of repeat breakdowns. We also explain how often to do it and what to check first.

What Rinnai boiler maintenance includes

Rinnai maintenance includes cleaning the heat exchanger and burner, checking the automation and hydraulics, and monitoring heating and hot water operation. A Tech Service technician removes the casing, assesses the primary heat exchanger, flushes it of scale and soot, cleans the burner, and checks ignition. Next is the automation: temperature and draft sensors, the board, ignition electrodes, and flame ionization control. For hydraulics, we check circuit pressure, the three-way valve, circulation pump, and threaded connections for leaks. We finish by checking both circuits: heating reaches operating mode without frequent cycling, and hot water holds temperature without spikes when the tap is opened. Maintenance is useful not only as prevention: during it, the technician spots early wear before it turns into a breakdown with cold water.

How often to do maintenance and what it gives

  • Heat exchanger cleaning: removes scale and restores water heating after a clog.
  • Burner cleaning: keeps the flame stable and ignition smooth without pops.
  • Automation check: catches electronics failures before an error code appears.
  • Hydraulics check: finds leaks and component wear at an early stage.
  • Hot water and heating control: confirms both circuits work normally.
  • Preventive maintenance: reduces the risk of repeat breakdowns and extends the life of boiler components.

Rinnai gas boiler fixes and their value

We've gathered the essentials for a Rinnai boiler owner: where to start troubleshooting and which signals not to ignore.

  • An error code isn't a verdict: the display signal is just a starting point; the component and when it appeared matter more.
  • Cold water while heating works: usually the three-way valve or a clogged secondary heat exchanger is to blame.
  • Pressure swings and cycling: look for the cause in the expansion tank and circuit tightness.
  • Board after a power surge: diagnostics come first, and only then do you decide if replacement is needed.
  • Regular maintenance: reduces the risk of repeat breakdowns and helps maintain stable heating longer.

20brands

Besides Rinnai, we repair other gas boiler brands in Almaty

We repair Rinnai gas boilers and other brands that have dedicated pages on this site.

We also repairWe also repairTECH SERVICE09

Besides Rinnai gas boiler repair, we fix other equipment in Almaty

Tech Service technicians repair other appliances too — with the same 1-year warranty on labour and parts.

BlogBlogTECH SERVICE10

Worth reading before Rinnai gas boiler repair in Almaty

Leave a review

Choose a platform — the TECH SERVICE page will open.

2ГИС2GISЯYandex Maps
Send a review with photos on WhatsApp