experience9 yearsRuslan Ts.
Washing machine and refrigerator repair technician
City
Language
What broke
Sections
Message on WhatsApp+7 (775) 030 02 94Mon–Fri 10:00–19:00, Sat–Sun 11:00–18:00
A technician arrives within 60 minutes anywhere in the city. Diagnostics are free, and there's a 1-year warranty on labor and parts.
Our own technicians4 to 20 years of experience




Repair prices
Below are typical symptoms of Beretta boilers and the components that cause them. The technician identifies the exact cause after a free diagnostic.
no ignition, piezo element, control board
from6 000 ₸
valve, heat exchanger, sensor
from6 000 ₸
flame sensor, draft, gas
from6 000 ₸
gaskets, heat exchanger, pump
from10 500 ₸
expansion tank, nipple, leak
from5 500 ₸
draft sensor, flue, flame sensor
from6 000 ₸
air in the system, pump, scale
from7 500 ₸
airlock, valve, control board
from6 000 ₸
The table lists the 'from' price for labor, for common jobs also the 'from' price of the part, plus the time required to complete the job.
1 visittime
from 10 500 ₸cost

BeforeAfter5 steps

Five steps from request to handing the boiler back to the owner after repair.
Describe the symptom and boiler model — the technician will prepare for the visit.
A technician arrives within 60 minutes anywhere in the city.
The technician identifies the faulty component and agrees on the scope of work.
The scope of work and parts are discussed before repair begins.
The boiler is started and its operation is demonstrated to the owner.
The home appliance repair department in Almaty has 8 technicians with 8 to 12 years of experience.

The department has 8 specializations — they are listed on the technicians' cards.
experience9 yearsWashing machine and refrigerator repair technician
experience12 yearsGeneral household appliance repair technician
experience10 yearsField technician for washing machine and refrigerator repair
experience8 yearsExpert washing machine repair technician
experience8 yearsField refrigerator repair technician
experience8 yearsSenior washing machine repair technician
experience11 yearsDishwasher repair technician
experience9 yearsWashing machine repair technician
We reply during working hours
The technician will arrange a convenient visit time and advise what the owner should prepare: access to the boiler and the unit's documents.

Warranty question? Call us
+7 (775) 030 02 947 898 reviews of repairs at TECH SERVICE in total
Айнур М.Order No. TS-2735 · 8 July 2026
oursБыло подозрение, что дело в плате, хотелось услышать второе мнение. Второй месяц — полёт нормальный.
Гаухар Н.Order No. TS-2805 · 23 April 2026
oursДамир М принял, посмотрел и сразу сказал, что делать. Сказали 9 500, а потом ещё и скидку сделали. Сделали и забыл про проблему.
Елена К.Order No. TS-8372 · 9 March 2025
oursПовод для визита: не зажигается. Дамир М возился с этим дольше, чем планировал, но довёл до конца. Починили и дали гарантию на месяц.
Аида Т.Order No. 2024-7770 · 28 March 2024
oursПоломка застала перед командировкой, тянуть было нельзя. Симптом был очевидный: течёт. Проверили на всех режимах, всё чётко.
Ляззат К.Order No. 2022-8617 · 8 November 2022
oursБыло подозрение, что дело в плате, хотелось услышать второе мнение. Основная жалоба — не греет. Проверил дома — всё на месте, ничего не забыли.
Жасмин Р.Order No. 13909 · 18 December 2019
oursСмотрел, у кого есть запчасти на такую модель. Не люблю сервисы, но этот запомнил. Симптом был очевидный: не зажигается. Отдельно спосибо мастеру — Дамир М, терпения ему хватило. Нужна была замена: теплообменник. Уже полгода — ни одного сбоя.
Азамат Е.Order No. TS-1811-750 · 31 July 2018
oursПозвонил знакомому, он раньше работал в сервисе, посоветовал этих. Обратился по поводу газовой колонки. Больше всего напрягало: течёт. Из деталей — розжиг. Заявку приняли по телефону, перезвонили через десять минут. По деньгам вышло адекватно, в другом месте просили больше. Включил, проверил, работает
Мадина Т.Order No. TS-1804-911 · 21 May 2018
oursНикита М честно сказал, что менять, а что ещё походит. Проверили на всех режимах, всё чётко.
Дмитрий Л.Order No. ZK-2017/954 · 2 December 2017
oursРаботаю допоздна, поэтому нужен был сервис с нормальным графиком. Первое, что заметил: не зажигаеться. Пользуюсь ежедневно, вопросов нет.
Асель Ж.Order No. 2016-8357 · 10 November 2016
oursДо этого обращался в другой сервис, там только развели руками. Первое, что заметил: не греет. Пользуюсь ежедневно, вопросов нет.
Didn’t find the answer? Message us on WhatsApp.
Ask a questionYou can check the system pressure and restart the boiler yourself. To fix the issue, you need a technician: they will run free diagnostics and give you a repair quote. A visit in Almaty takes about an hour.
No, installing a gas boiler requires a project and approvals, so you can't do it yourself. Improper installation is dangerous and may lead to refused service. Leave the work to professionals.
The boiler must not be installed in living rooms, bathrooms, or above a gas stove. You can't mount it on combustible walls without protection or in areas without ventilation. Exact requirements depend on the model and project.
There may be several reasons: no draft, ignition failure, a faulty sensor, or a faulty board. The error code on the display will point you in the right direction. A technician will run diagnostics on site and identify the fault.
It depends on the fault: some Beretta board issues can be fixed by repair, while serious damage requires replacement. The technician decides after free diagnostics. The warranty on labor and parts is one year.
Immediately shut off the gas valve, don't turn on any electrical appliances, and open the windows. Leave the premises and call the emergency service. The technician will come after the leak is fixed.
Tech Service repairs Beretta gas boilers in Almaty with its own technicians who have 4 to 20 years of experience. A technician arrives at your home within 60 minutes anywhere in the city, diagnostics are free, and we provide a 1-year warranty on labor and parts. We quote the price after diagnostics and you can pay via Kaspi QR, Kaspi Red, bank card, cash, or bank transfer for companies.
The code on the screen is not a verdict but a clue that starts the diagnosis. Here's how to read it and what it says about the condition of the unit.
The code on the Beretta display is a signal from the control board indicating which component has gone beyond acceptable parameters, and our technician first checks it against the fault table for the specific model line. The board detects deviations from sensors and the pressure switch, assigns an alphanumeric code to the event, and blocks ignition to prevent gas from entering a faulty circuit. The code points to a group of components, not a specific failed part: a single symbol can indicate the ionization electrode, the gas valve, or the NTC sensor. The same code on different Beretta lines may point to different components, so the interpretation must be checked against the boiler model, not a generic table from the internet. If you need Beretta gas boiler repair in Almaty, a technician will visit your home and check the code against the table for your specific model.
| Group | What it indicates | What the technician checks |
|---|---|---|
| Ignition and flame | no ignition or flame goes out | ignition electrode, ionization electrode, gas valve |
| Draft and flue gas removal | pressure switch or fan failure | pressure switch, turbine fan, coaxial flue |
| System pressure | pressure drop or spike | expansion tank, fill valve, pressure sensor |
| Temperature | overheating or sensor failure | NTC sensor, heat exchanger |
| Control board | communication or memory error | Beretta control board, contacts and connectors |
The two most common scenarios are the boiler not starting at all or running for heating but not heating water from the tap. Let's look at which components are responsible.
When a Beretta won't ignite, our technician checks the chain in order: gas supply, gas valve, ignition element, ionization sensor, and only then the control board. First, we make sure the valve on the supply line is open and there is fuel in the system: without it, no model in the dual-circuit range will start. Next, we check the gas valve — it opens the supply to the burner on a signal from the board, and clogged nozzles or a stuck stem break this chain. A spark occurs but ignition fails if the part is dirty or the gap is off. Most often the culprit is not the valve but a shifted ionization sensor: the board doesn't see the flame and cuts off the fuel, even though the burner is fine. That's why before replacing the board, we always check the probe and ignition gap — this saves the owner the cost of a component that is actually working. If self-checks don't help, it's better to entrust Beretta gas boiler repair in Almaty to a technician with experience specifically with this brand.
It is important for the buyer to understand how a specialist distinguishes an electronics fault from a sensor and burner issue. We show the logic of finding the cause and explain in which cases the unit is restored and in which it is replaced.
Our technician goes from simple to complex: first checks the NTC sensors and pressure switch, then the burner and electrodes, and only then draws a conclusion about the Beretta control board. The electronics control ignition, the burner, and heating and DHW modes, so its failure affects several functions at once. The NTC sensor is responsible for the coolant temperature, the pressure switch for draft and air presence, and the electrodes for ignition. An oxidized connector or a thermistor that has gone open circuit produce the same error as a broken electronics, so replacing the unit without checking the wiring is unnecessary expense. In our practice, most "condemned" modules turned out to be functional after checking the contacts and wiring. The logic is simple: until the sensor, pressure switch, and burner are ruled out, it is too early to verdict on the electronics.
We perform Beretta boiler diagnostics on-site for free: the technician checks the codes, sensors, gas part, and operation in both modes, and then names the repair cost. First, the codes are read from the display and compared with the actual behavior of the unit during ignition. Then the NTC sensors, pressure switch, electrodes, and connector condition are checked, followed by operation in heating and hot water modes: this shows whether the defect appears in one mode or both. The gas part is inspected separately because some errors are related to draft and supply. It is useful to be present during diagnostics: the technician shows on site which unit is causing the deviation and explains why they recommend restoration rather than replacement. A call-out within the city takes up to 60 minutes.
| Board situation | What we do | Why |
|---|---|---|
| Local defect, one element damaged | board repair | the unit is otherwise functional |
| Oxidation of contacts and connectors | cleaning and contact restoration | the cause is in the wiring, not the board |
| Damage to key elements | board replacement | repair is unreliable, modes do not hold |
| Failure after a voltage surge | diagnostics and decision based on results | need to assess the extent of damage |
Pressure drops, noise during ignition, and cycling are common complaints from Beretta owners. It is not always a breakdown, but it is not always normal either: we explain where the line is.
If noise is accompanied by a smell, pressure drop, or a repeating error code, we advise not delaying a technician visit and not using the boiler until it's inspected. We check increasing humming by components: flue fan, circulation pump, pressure switch. The turbine collects dust over time and starts humming, pump bearings whine from wear, and the pressure switch checks draft and flue fan operation — if it fails, the boiler locks out. Our technician arrives within 60 minutes anywhere in the city. Based on our technicians' experience, increasing humming gradually leads to component failure, so an early visit means less work than an advanced breakdown. We provide free diagnostics and quote the price after inspection.
While the technician is on the way, the most important thing is not to harm the boiler or the premises. Here's what to do in case of a gas smell, lockout, or pressure drop, and how the visit itself goes.
A Tech Service technician arrives at your home within 60 minutes anywhere in the city, diagnoses the Beretta boiler on site and fixes the issue right away if possible; if workshop service is needed, that's also an option. Diagnostics are free, the warranty is 1 year on labor and parts, and you can pay any way you like. Before the visit, it helps to clear access to the boiler — move furniture aside, remove a shelf or box from the pipes — and remember which mode triggers the fault. This speeds up finding the cause and reduces the risk when the problem doesn't show up during the inspection and the conversation goes blind. Our field technician has been working with Beretta for years: the specialists have 4 to 20 years of hands-on experience, and from your description of the boiler's behavior they often narrow down the causes before even opening the panel.
Beretta is an Italian brand with its own control systems, and it's best to trust those who know these specific boilers. Here's why and on what terms we work.
Our specialists with 4 to 20 years of experience work with Beretta's Italian control systems and know its board, burner, three-way valve and NTC sensors, rather than fixing everything by a generic scheme. The Beretta control board is connected to the gas burner, three-way valve and NTC sensors in a single circuit, and a failure of one component often shows up as a symptom of another. Someone who has handled these boilers many times can tell a dying sensor from a working one by its readings, instead of replacing everything in sight. Our technicians service Beretta gas boilers in Almaty and work with this control system following a proven routine. Beretta's specific feature is the close connection between its electronics and the piping, so someone who knows the brand is less likely to replace working components 'on suspicion'.
We provide a 1-year warranty on labor and parts, diagnostics are free, the specialist gives you the price after diagnostics, and you can pay any way you like. The warranty also covers parts, so if the same component fails again within a year, it's handled under warranty rather than as a new order. Diagnostics are free: the technician arrives, finds the cause and only then quotes the price for the work. We accept Kaspi QR, Kaspi Red, card, cash or bank transfer — whatever suits the owner. We arrive within 60 minutes anywhere in the city, so you won't have to wait a week. In my view, it's exactly the combination of 'free diagnostics plus warranty on parts' that removes the owner's main fear — that they'll be charged again for replacing a working component.
We've gathered brief takeaways on troubleshooting Beretta faults in one place — you'll have a clear logic of actions at hand, not just a list of alarming symptoms.
20brands
Beretta is one of the brands the service center works with. Below are the brands that have dedicated pages on the site.
Tech Service technicians repair other appliances too — with the same 1-year warranty on labour and parts.
Refrigerator Repair in Almatyfrom 3 000 ₸
Washing Machine Repair in Almatyfrom 3 000 ₸
Dishwasher Repair in Almatyfrom 3 500 ₸
Oven Repair in Almatyfrom 3 000 ₸
Cooktop Repair in Almatyfrom 3 500 ₸
Air Conditioner Repair in Almatyfrom 3 500 ₸
Boiler and Water Heater Repair in Almatyfrom 2 500 ₸
Freezer Repair in Almatyfrom 6 000 ₸
Tumble Dryer Repair in Almatyfrom 5 000 ₸
Coffee Machine Repair in Almatyfrom 2 500 ₸
Robot Vacuum Cleaner Repair in Almatyfrom 3 500 ₸
Vacuum Cleaner Repair in Almatyfrom 1 500 ₸
Microwave Oven Repair in Almatyfrom 2 000 ₸
Hair Dryer Repair in Almatyfrom 1 500 ₸
Iron Repair in Almatyfrom 3 000 ₸
Electric Kettle Repair in Almatyfrom 2 500 ₸
Mixer Repair in Almatyfrom 2 500 ₸
Multicooker Repair in Almatyfrom 500 ₸












