experience9 yearsRuslan Ts.
Washing machine and refrigerator repair technician
City
Language
What broke
Sections
Message on WhatsApp+7 (775) 030 02 94Mon–Fri 10:00–19:00, Sat–Sun 11:00–18:00
A technician arrives within 60 minutes anywhere in the city. Diagnostics are free.
Our own technicians4 to 20 years of experience




Repair prices
These are the symptoms that most often lead to a service call. Free diagnostics will pinpoint the exact cause.
no gas, safety lockout, control board
from6 000 ₸
clogged nozzles, weak flame sensor
from6 000 ₸
faulty three-way valve, clog
from7 500 ₸
air in the system, pump failure
from7 500 ₸
scale in the heat exchanger, pump wear
from10 500 ₸
worn gaskets, cracked heat exchanger
from12 000 ₸
control fault, incorrect mode
from7 500 ₸
leak in the system, faulty expansion tank
from7 500 ₸
The table lists the 'from' price for labor, for common jobs also the 'from' price of the part, plus the time required to complete the job.
1 visittime
from 7 500 ₸cost

BeforeAfter5 steps

Five steps from your call to checking the boiler's operation.
You describe the symptom. The technician confirms the model and heads out.
The technician arrives anywhere in the city within 60 minutes of your request.
The technician checks component by component and identifies which part has failed.
Once the price is agreed, the technician performs the work and replaces parts.
The technician checks that all connections are tight after reassembly and demonstrates the boiler running in heating and hot water modes.
The home appliance repair department in Almaty has 8 technicians with 8 to 12 years of experience.

The department has 8 specializations — they are listed on the technicians' cards.
experience9 yearsWashing machine and refrigerator repair technician
experience12 yearsGeneral household appliance repair technician
experience10 yearsField technician for washing machine and refrigerator repair
experience8 yearsExpert washing machine repair technician
experience8 yearsField refrigerator repair technician
experience8 yearsSenior washing machine repair technician
experience11 yearsDishwasher repair technician
experience9 yearsWashing machine repair technician
We reply during working hours
Choose the channel that works best for you and have your boiler model, error code, and when the symptom appeared ready — this speeds up diagnostics.

Warranty question? Call us
+7 (775) 030 02 947 898 reviews of repairs at TECH SERVICE in total
Богдан С.Order No. 938445 · 24 March 2026
oursДруг посоветовал, у него похожая история была. Нужен был ремонт газовой колонки — обратился сюда. Проблема — не зажигается. Поставили новую деталь: мембрана. По цене не скажу, что дёшево, но справедливо. Заявку приняли по телефону, перезвонили через десять минут. Вернули в тот же день, всё функционирует.
Ольга М.Order No. 2024-2927 · 9 September 2024
oursОсновная жалоба — не греет воду. Никита М помог выбрать, без навязывания. Сказать, что доволен — ничего не сказать
Айгуль К.Order No. TS-1267 · 15 July 2023
oursЖалоба простая: не греет. Отдельно скажу про мастера: Дамир М — спокойный, без лишней суеты. Проверили при мне, показали, что всё держит.
Бакыт Ж.Order No. TS-2209-675 · 27 December 2022
oursСмотрел, у кого есть запчасти на такую модель. Разобрали, посмотрели: плата. Сделали аккуратно, следов разборки не видно)
Ерасыл Б.Order No. TS-2202-231 · 2 April 2022
oursСимптом был очевидный: не зажигаеться. Никита М приехал в тот же день, хотя был конец смены. Уже полгода — ни одного сбоя.
Станислав К.Order No. TS-2176 · 8 March 2020
oursПервое, что заметил: не греет. Никита М всё объяснил и не пытался впарить лишнее. Техсервис в Алматы, если что, вот их адрес — не пожалел. Работает как раньше, придирок нет
Алмас Д.Order No. TS-1908-726 · 14 November 2019
oursСимптом был очевидный: ошибка. Дамир М помог выбрать, без навязывания. Пользуюсь ежедневно, вопросов нет
Максим Ю.Order No. 58907 · 7 March 2019
oursПробовал найти мастера в своём районе, но все были заняты. Повод для визита: не зажигается. Гудит ровно, не греется, всё как надо
Дмитрий Л.Order No. ZK-5171 · 21 July 2018
oursХотел сначала вызвать мастера на дом, потом передумал. Больше всего напрягало: ошибка. Сделали аккуратно, следов разборки не видно.
Руслан Д.Order No. 2017-6867 · 24 April 2017
oursПроблема — течёт. Никита М помог выбрать, без навязывания. Проверил дома — всё на месте, ничего не забыли.
Didn’t find the answer? Message us on WhatsApp.
Ask a questionRequest a service call and a Celtic boiler technician will come to your home within 60 minutes anywhere in the city. Diagnostics are free, and the warranty on labor and parts is one year.
Gas equipment repairs must be done by a licensed specialist — tampering with it yourself is dangerous. Our technician comes to your home, runs free diagnostics, and fixes the Celtic boiler on site.
Check that the gas valve is open, the power is on, and the system pressure is normal. If your Celtic boiler won't start, call a technician: they'll find the cause for free and repair it at your home.
No, gas equipment requires a license, and tampering with it without one is dangerous. You can check the power, valves, and system pressure yourself, but leave disassembly and adjustment of the Celtic boiler to a service technician.
Incorrect reassembly can cause a gas leak, carbon monoxide poisoning, and damage to the circuit board or heat exchanger. A licensed technician will fix the problem safely and provide a warranty on labor and parts.
It depends on the model and the type of damage: some boards are repaired by soldering and replacing components, while others are replaced entirely. After free diagnostics, the technician will tell you which option is more reliable in your case.
Tech Service repairs Celtic gas boilers in Almaty with its own field technicians who have 4 to 20 years of experience. The technician arrives within 60 minutes anywhere in the city, diagnostics are free, and there is a 1-year warranty on labor and parts. The price is quoted after diagnostics, and payment can be made by any method.
An error code on the display is a starting point for the technician, not a final verdict on the boiler. Here's how Celtic's indicators narrow down the components to check and why a single symptom can point to several possible causes at once.
An error code on the Celtic display points to a specific group of components — ignition, sensors, circulation, or flue gas removal — and that's where diagnostics begin. The boiler's indicators work like this: the control board doesn't record the fault itself but a parameter deviation: no signal from the flame ionization sensor, pressure out of range, or a fault in the fan circuit. The same code on different models in the series can mean different things, so the interpretation is checked against the specific unit's manual, not a generic table from the internet. Write down the code before turning off the boiler — after a restart the indicator may reset, and the technician will lose the quickest clue that saves the first minutes on site. If the code interpretation doesn't help and you need Celtic gas boiler repair in Almaty, the technician starts by checking the component group the board pointed to.
We divide ignition failure into two branches — gas supply (gas valve, line tightness) and electronics (ionization sensor, board) — and tell them apart by how the burner behaves at startup. If you hear the ignition click but the gas burner doesn't light, check the gas valve and line pressure: the valve may not open because the coil isn't getting power. When the flame appears and immediately goes out, the logic is reversed — gas is present, but the control board isn't getting confirmation from the flame ionization sensor and shuts off the supply. Checking the gas line for leaks is mandatory in both branches, because a leak at the connections is more dangerous than any error on the screen. If the burner lights and goes out after a couple of seconds, the ionization sensor is more often to blame than the gas — the flame is there, but the unit "doesn't see" it.
We check a complete failure to start along the power chain — from the pressure sensor and expansion tank to the control board — because the boiler won't start if the unit doesn't see the correct conditions. The pressure sensor tells the board that there's water in the circuit at the required pressure; if the reading drops below the threshold, the unit goes into protection and won't start either the burner or the pump. The expansion tank adds a second cause: if its air chamber has lost pressure, water expands when heated and briefly raises the pressure, after which the sensor again detects a deviation. Boiler diagnostics go from simple to complex: first the pressure gauge readings and sensor condition, then the control board power. Before calling a technician, check that the boiler isn't in low-pressure protection — topping up to the working mark sometimes restores startup without repair.
Two common complaints from Celtic owners — hot water stays cold even though heating works, and pressure needs topping up. Here's which component is behind each symptom and what the technician checks.
When heating works but hot water is cold, we first check the three-way valve and the DHW circuit temperature sensor — they're responsible for switching flows. The three-way valve directs the heat carrier between the heating circuit and the secondary heat exchanger: if the stem is stuck, water only goes to the radiators and cold water comes out of the tap. If the DHW circuit temperature sensor gives incorrect readings, it prevents the boiler from switching to hot water mode — the board gets a false signal that the set temperature has already been reached. Hydraulic fittings and the secondary circuit get clogged with scale, and then even a working valve won't let enough flow through. A clogged secondary circuit gives the same symptom as a stuck valve, so the technician checks both components before replacing parts. If you need Celtic gas boiler repair in Almaty, the technician checks both components before replacing parts.
We associate pressure drops with three components — the expansion tank, the pressure sensor, and circuit tightness — and tell them apart by whether the needle drops only during heating or constantly. During heating, the coolant expands, and if the expansion tank membrane has lost its elasticity or the air chamber has lost its charge, the excess volume has nowhere to go — the needle goes up and then drops after cooling. A dirty or worn pressure sensor sends distorted readings to the board, and the boiler shuts down on an error even though the actual pressure is normal. A constant drop points to a leak in the heating circuit — connections, radiators, fill valve. If pressure drops only when the boiler is hot, it's more often the expansion tank rather than a leak — constant topping up in this case masks the cause.
Noise and frequent cycling usually indicate a clogged heat exchanger or impaired circulation, which prevent heat transfer and cause the boiler to overheat quickly. Scale on the walls of the primary heat exchanger acts as an insulator: the burner heats the metal, the coolant doesn't absorb the heat fast enough, the sensor detects overheating and shuts off the flame — a minute later the cycle repeats. A circulation pump with reduced performance or a clogged impeller produces weak flow, radiators heat unevenly, and the boiler goes into protection more often. Humming and whistling in the circuit come from air pockets and narrowed passages. This symptom is rarely fixed by adjusting the board — if the cause is scale, adjustments only delay flushing and accelerate wear on the component.
Maintenance is tied to the season: before the first cold snap, the heat exchanger is checked and flushed. Here's how to recognize a clogged component and what boiler preparation for the heating season includes.
A clogged heat exchanger shows up as weak heating with the burner running, noise, and rising gas consumption — heat simply doesn't transfer to the water fast enough. Scale deposits on the inner walls of the passages, the layer narrows the flow and hinders heat transfer, and the metal heats up more than it should. The owner notices: radiators take longer to heat up, tap water is only lukewarm, the flame burns but there's almost no effect, and the gas bill has grown noticeably without increased load. Flushing the heating system and the heat exchanger itself restores flow through the passages before they become completely blocked. The technician assesses even heating across the circuit and compares it with the unit's specifications. Cleaning helps while the passages are still open; with heavy scale and signs of overheating, the part can't be restored by flushing, and the technician discusses replacement.
Cleaning frequency depends on water quality and load, not on the calendar — in hard water, scale builds up noticeably faster. Almaty tap water contains a lot of hardness salts, so the heat exchanger here clogs more actively than in regions with soft water. A boiler running non-stop in winter accumulates deposits faster than a unit at a country house with seasonal use. During inspection, the technician assesses the condition of the channels and the thickness of the layer, rather than following a general schedule from the manual. For the owner, the guideline is not "once every N years" but the appearance of noise, weak heating, and increased fuel consumption; these signs matter more than a schedule. The earlier such signals are noticed, the easier it is to restore the unit to working condition without replacement.
Celtic electronics fail more often than mechanical components, but not every failure requires board replacement. We explain in which situations the unit is restored and in which it is replaced, and what technicians check first.
We first troubleshoot the board — some failures are related to soldering and individual components and can be restored, while replacement is needed when the board itself is damaged. The control board is the brain of the boiler: it reads the flame ionization sensor signal, controls the gas valve and circulation pump, manages ignition, and monitors the circuit temperature. Troubleshooting the components reveals the failed element: a microcrack in the solder, a blown capacitor, or a burnt trace — these are different scenarios with different solutions. Our technician comes to your home, removes the board, and checks it along the chain from connectors to output stages, comparing signals with the specified values. The decision is made based on troubleshooting results, not on appearance — a burnt element and a burnt trace require different approaches.
| Component | When repaired | When replaced | What we check |
|---|---|---|---|
| Control board | Solder or individual component failure | Damage to traces and the board itself | Sensor signals and trace integrity |
| Heat exchanger | Scale without signs of overheating | Heavy scale, deformation, leak | Channel patency and tightness |
| Gas valve | Clogging and misadjusted settings | Seat wear and loss of tightness | Response to ignition command |
| Circulation pump | Clogging and shaft seizure | Winding and bearing wear | Circulation and current consumption |
| Expansion tank | Incorrect air pressure | Membrane rupture | Whether it holds pressure when heating |
A transparent process removes the owner's main fear — being upsold. We show the path from request to warranty on labor and parts, so the decision is made based on the inspection, not over the phone.
Our technician arrives within 60 minutes anywhere in the city, and diagnostics are free — on site, they identify the faulty component and explain the cause. Celtic gas boiler service in Almaty starts with fault detection: the field technician checks ignition, circuit pressure, heat exchanger condition, and the control board, and records deviations for each component. Boiler diagnostics are done on site, without removing the equipment and without randomly disassembling the gas section — first the causes are found, then a solution is proposed. The owner sees which component has failed and why, instead of hearing a vague "needs repair." The technician quotes the price after free diagnostics, so the owner decides based on the inspection, not over the phone — and knows upfront what they are paying for.
We perform most Celtic boiler work at the customer's home, and we take a component to the service center only when board soldering or work that cannot be done on site is needed. The field technician handles the gas section, hydraulics, cleaning, and sensor replacement at the owner's place — access to the boiler is all that's required. The control board, ignition module, and other electronic components are sometimes easier to diagnose at the service center, where there are conditions for testing under load. The decision depends on the component, not on convenience: the gas section and hydraulics are done at home, while electronics are sometimes better diagnosed at the service center so we don't guess about the cause of the failure right at the boiler. This approach saves the owner time — there's no need to bring the entire unit if removing one module is enough.
We provide a 1-year warranty on labor and parts, so if the problem returns, the technician handles it under warranty, not as a new paid job. If the boiler shows an error again or loses pressure after service, the owner contacts us with a description of the symptom — the repeat visit is recorded under the same job. If an installed part fails, it is replaced, not repaired again at the customer's expense. The parts warranty is just as important as the labor warranty — if a part fails, the owner is covered on both counts, and replacing the component instead of repairing it falls within our obligations. You can clarify the scope of warranty coverage for a specific case before work begins — the technician explains this during diagnostics.
Gas boiler repair comes down to three steps: read the indication, find the component by symptom, and decide based on fault detection. Below is a short summary to help you stay on track during diagnostics.
20brands
We repair gas boilers from popular brands. Choose yours — the brand page covers typical issues and fault patterns.
Tech Service technicians repair other appliances too — with the same 1-year warranty on labour and parts.
Refrigerator Repair in Almatyfrom 3 000 ₸
Washing Machine Repair in Almatyfrom 3 000 ₸
Dishwasher Repair in Almatyfrom 3 500 ₸
Oven Repair in Almatyfrom 3 000 ₸
Cooktop Repair in Almatyfrom 3 500 ₸
Air Conditioner Repair in Almatyfrom 3 500 ₸
Boiler and Water Heater Repair in Almatyfrom 2 500 ₸
Freezer Repair in Almatyfrom 6 000 ₸
Tumble Dryer Repair in Almatyfrom 5 000 ₸
Coffee Machine Repair in Almatyfrom 2 500 ₸
Robot Vacuum Cleaner Repair in Almatyfrom 3 500 ₸
Vacuum Cleaner Repair in Almatyfrom 1 500 ₸
Microwave Oven Repair in Almatyfrom 2 000 ₸
Hair Dryer Repair in Almatyfrom 1 500 ₸
Iron Repair in Almatyfrom 3 000 ₸
Electric Kettle Repair in Almatyfrom 2 500 ₸
Mixer Repair in Almatyfrom 2 500 ₸
Multicooker Repair in Almatyfrom 500 ₸












