experience9 yearsRuslan Ts.
Washing machine and refrigerator repair technician
City
Language
What broke
Sections
Message on WhatsApp+7 (775) 030 02 94Mon–Fri 10:00–19:00, Sat–Sun 11:00–18:00
A technician arrives within 60 minutes anywhere in the city. Free diagnostics, 1-year warranty on labor and parts.
Our own technicians4 to 20 years of experience




Repair prices
Symptoms that most often prompt a service call, and likely causes. The exact cause is determined by diagnostics.
refrigerant leak, compressor failure
from10 000 ₸
loose door seal, sensor failure
from9 000 ₸
thermostat failure, refrigerant leak
from10 000 ₸
clogged drain, displaced seal
from6 000 ₸
compressor wear, loose mounts
from18 500 ₸
sensor failure, control board issue
from9 000 ₸
power circuit break, relay failure
from7 500 ₸
worn seal, door misalignment
from6 000 ₸
The table lists the 'from' price for labor, for common jobs also the 'from' price of the part, plus the time required to complete the job.
1 visittime
from 6 000 ₸cost

BeforeAfter5 steps

Five steps from request to checking the freezer's operation.
Describe the symptom and freezer model so the technician brings the right tools.
A technician arrives within 60 minutes anywhere in the city, with a set of tools and instruments.
The technician clarifies the model, symptom, access to the outlet, and freezer location.
The technician states the cause and cost; work begins after your approval.
Test run and cold check, then the appliance is handed back to the owner.
The home appliance repair department in Almaty has 8 technicians with 8 to 12 years of experience.

The department has 8 specializations — they are listed on the technicians' cards.
experience9 yearsWashing machine and refrigerator repair technician
experience12 yearsGeneral household appliance repair technician
experience10 yearsField technician for washing machine and refrigerator repair
experience8 yearsExpert washing machine repair technician
experience8 yearsField refrigerator repair technician
experience8 yearsSenior washing machine repair technician
experience11 yearsDishwasher repair technician
experience9 yearsWashing machine repair technician
We reply during working hours
Specify a convenient visit time and describe the symptom — the technician will prepare for the specific issue and arrive in the chosen interval.

Warranty question? Call us
+7 (775) 030 02 947 898 reviews of repairs at TECH SERVICE in total
Индира П.Order No. ZK-2026/602 · 28 May 2026
oursПозвонил знакомому, он раньше работал в сервисе, посоветовал этих. Ремонт морозильника — вот с этим и пришёл. Основная жалоба — не закрывается. Вышло дешевле нового, что логично. Объяснили по телефону, что можно не везти, но я всё равно привёз. Заодно поменяли: уплотнитель. Нагрев в норме, постороних звуков нет.
Алмас Д.Order No. 82534 · 10 April 2026
oursПоломка застала перед командировкой, тянуть было нельзя. Симптом был очевидный: не морозит. Шум пропал, работает мягко!!
Жасмин Р.Order No. TS-4294 · 2 June 2025
oursТехника на гарантии уже не была, так что выбор был свободный. Сначала думал, что ерунда, но появилось: не морозит. В списке работ — термостат. Сказали 12 000, я согласился без торга. Созвонились, договорились на удобное время, никто не тянул. Tech-service оказался ближе всех, за это и выбрал. В общем, доволен. Нагрев в норме, посторонних звуков нет!!
Камила А.Order No. TS-4649 · 17 December 2024
oursПробовал найти мастера в своём районе, но все были заняты. Уже полгода — ни одного сбоя.
Елдос К.Order No. 2024-9031 · 7 October 2024
oursПозвонил в три места, здесь единственные назвали цену сразу. Жалоба простая: не закрывается. Внешне как новый, если не считать мелкой царапины
Ольга М.Order No. 234137 · 2 March 2024
oursДильмурат С взялся за то, от чего другие отказались. Проверили при мне, показали, что всё держит.
Дарья С.Order No. TS-2110-940 · 4 April 2021
oursПозвонил знакомому, он раньше работал в сервисе, посоветовал этих. Повод для визита: наледь. Никита М честно сказал, что менять, а что ещё походит. Уже полгода — ни одного сбоя.
Елена К.Order No. 724291 · 3 January 2021
oursБыло важно, чтобы сделали до выходных — гости, то-сё. Симптом был очевидный: намерзает. Сделали аккуратно, следов разборки не видно.
Евгений М.Order No. 425281 · 21 April 2020
oursПробовал найти мастера в своём районе, но все были заняты. Основная жалоба — не морозит. Пользуюсь ежедневно, вопросов нет.
Нурлан Б.Order No. ZK-9483 · 10 September 2018
oursНужен был счёт и чек, у нас техника на балансе организации. Позвонил узнать про ремонт морозильного ларя. Больше всего напрягало: не включается. Никита М снял деталь, показал износ, вопросов не осталось. Всё оформили по договору, с печатью. Даже с учётом запчасти вышло гуманно. В списке работ — компрессор. Работает как раньше, придирок нет.
Didn’t find the answer? Message us on WhatsApp.
Ask a questionLeave the freezer unplugged for a few hours, then plug it in and check if the compressor starts. If there's no cooling and you hear clicking, the start relay may have tripped or the compressor has failed — you need a technician.
Yes, with repeated clicking the compressor tries to start and overheats, which speeds up wear. It's best to unplug the freezer until the technician arrives and not turn it on again.
After defrosting, noise often comes from the fan or a poorly fitted seal that makes the body vibrate. If the hum is sharp and metallic, the technician checks the compressor mounts and the condition of the tubes.
The code points to a specific component: a sensor fault, defrost problems, or a communication failure between the board and the module. The interpretation depends on the model, so the technician checks the code against the manufacturer's table and inspects the corresponding part.
The 1-year warranty covers the work performed and the parts installed. If the same issue comes back due to the repair, the technician will return and resolve it under the warranty terms.
Most often the cause is a faulty thermostat, refrigerant leak, or defrost system failure, so the compressor doesn't get the signal to stop. During diagnostics, the technician will identify the component; it depends on the model.
Tech Service repairs Atlant freezers in Almaty with its own technicians who have 4 to 20 years of experience. A technician arrives at your home within 60 minutes anywhere in the city, diagnostics is free, and the price is quoted after inspection. We provide a 1-year warranty on labor and parts and you can pay via Kaspi QR, Kaspi Red (instalments), bank card, cash, or bank transfer for companies.
The Atlant freezer isn't freezing but the light is on — that's the first sign that cooling is lost while power is still supplied. Let's break down what the indicators mean and the order of first checks.
A flashing indicator on the Atlant panel signals that the temperature has gone outside the operating range, not that a specific part has failed. The display receives data from the temperature sensor inside the chamber and, through the control module, raises an alarm: cooling has dropped below normal, the compressor can't keep up, or the defrost assembly hasn't completed its cycle. Constant flashing is most often related to the sensor; intermittent flashing together with a sound signal points to the compressor trying to start; and a light that goes off after defrosting indicates evaporator icing. Pay attention to the rhythm: steady flashing without sound usually comes from the sensor, while rapid flashing with a beep comes from the start relay that isn't pulling the motor. By the nature of the flashing — constant, intermittent, or with sound — the technician narrows it down: sensor, defrost, or refrigerant circuit. So remember and show the technician exactly how the panel behaves.
| Display signal | Likely assembly | What the technician checks |
|---|---|---|
| Temperature indicator flashing | Temperature sensor | Sensor resistance and contacts |
| Alarm stays on after defrost | Defrost assembly | Defrost heater, timer, thermostat |
| Light and sound at the same time | Start relay | Compressor start and windings |
| Error doesn't clear after reset | Control module | Board power and traces |
| Cooling present but weak | Fan | Fan blade rotation and ice buildup |
If the light is on but there's no cooling, we first check whether the compressor is running and whether the circuit holds pressure — this separates electrical issues from refrigerant loss. We listen to the motor: a hum without vibration of the housing indicates a failed start relay, complete silence points to the thermostat or board, and running without stopping suggests a refrigerant leak. Next we look at the evaporator: even icing hints at the sensor, while an empty circuit with the compressor running points to a refrigerant leak. A technician visit in the city takes 60 minutes, diagnostics are free, and during the visit we measure pressure and check the windings. Before the technician arrives, don't take the panel apart or defrost the chamber "just in case": how the appliance behaves before any intervention makes it easier to tell whether refrigerant has leaked or the start relay has failed.
Every Atlant freezer failure has a recognizable symptom. Below is the chain "symptom → likely cause → technician's actions" so you can describe the problem before the specialist arrives.
Constant operation without shutting off and ice on the walls most often mean a failure in the defrost circuit or a thermostat that doesn't let the motor stop in time. The defrost circuit includes the heater, timer, and sensor: when the timer doesn't switch modes, the evaporator gets covered in frost, and the motor hums without pauses. With a faulty thermostat, the circuit doesn't open when the required temperature is reached — the chamber freezes longer than needed, and ice builds up in layers. The technician tests the sensors, checks the defrost timer and heater resistance, then sees whether the frost clears from the evaporator after a forced cycle. He also assesses the motor's behavior on a defrosted evaporator: if pauses appear, the cause is in the defrost circuit, not the thermostat. If the cause isn't fixed, the motor wears out and the frost grows faster — so delaying diagnostics costs more than repairing the defrost sensor. Atlant freezer repair in Almaty starts with the same check of the defrost circuit and thermostat.
Clicking without starting usually points to the start relay or the motor's start circuit, which prevents the motor from starting. The relay tries to send a pulse, there's a click, the motor jerks and stalls — this repeats at intervals. Besides the relay, the start circuit has a capacitor: its breakdown produces the same symptom, so the technician checks both components and measures the windings for opens and turn-to-turn shorts. Wiring and terminals are inspected separately — an oxidized contact mimics a failed start component and confuses things during the first inspection. Sometimes the relay is fine but the compressor itself is seized: then the click comes from the thermal protection, which trips and releases the motor after a pause. When the compartment stays silent after defrosting, don't rush to "catch up" with repeated starts — frequent start attempts finish off the motor, and instead of the relay the whole assembly gets replaced.
We distinguish these faults by motor behavior and circuit pressure: if the motor hums and doesn't shut off — more often the thermostat; if it's silent or runs idle — the compressor or a leak. A humming unit without pauses while cold is normal points to a thermostat that doesn't open the circuit; a silent motor with good power sends the technician to the windings and start circuit. A compressor running idle with a warm evaporator makes us look for refrigerant loss at joints and the charging port. Our technicians start with pressure measurement and leak detection, not with a verdict to replace the motor. A refrigerant leak masquerades as a "weak compressor," so the technician first looks for refrigerant loss and only then concludes the motor needs replacement.
An Atlant freezer holds a noticeably lower temperature than a refrigerator and works with separate defrost logic, so both the faults and the service approach differ from a refrigerator of the same brand.
A freezer holds a noticeably lower temperature than a refrigerator, so the load on the compressor and defrost system is higher, and the sensors work in a different range. The low-temperature circuit is designed for constant cold around minus eighteen degrees and below, while the refrigerator compartment lives in a positive mode where defrosting happens more often and more gently. The freezer compressor turns on less often, but each start pulls a larger differential, and the thermal sensor records changes in a narrow corridor of values. The freezer's defrost is designed differently: the heater and sensor are placed on the evaporator, and their job is to remove ice without raising the compartment temperature above critical. Because of the low temperature mode, a minor sensor fault here quickly turns into ice buildup and loss of cold — something that would go unnoticed in a refrigerator is immediately visible in a freezer.
| Model type | Frequent failure point | What the owner complains about |
|---|---|---|
| Upright with No Frost | Defrost sensor, fan | Ice on walls, temperature swings |
| Upright with electronics | Control module, sensor | Error code on display |
| Chest freezer | Thermostat, gasket | Doesn't hold cold, ice buildup |
| Model with mechanical control | Thermoregulator, start circuit | Runs nonstop, clicks |
Common parts — the compressor, start circuit, and refrigerant line: these components are designed similarly, so our technician is equally confident working on both Atlant refrigerators and freezers. The start assembly in both categories includes a relay and a protective element, and the refrigerant path follows the same layout with a compressor, condenser, and evaporator. Our technicians have been working with refrigeration equipment for four to twenty years and during free diagnostics they check exactly this common foundation — line pressure, compressor startup, and circuit integrity. Experience with both categories helps avoid treating the symptom: the technician immediately understands where a typical refrigerator cause ends and freezer-specific issues begin, and doesn't replace a working component because of a similar external sign.
We handle most Atlant freezer breakdowns at the customer's home, and we only take equipment to the service center when a complex unit repair is needed.
At home we replace the start relay, thermostat, sensors, door seal, and fix defrost faults — these are jobs that don't require opening the circuit. The start relay and thermostat are replaced without opening the refrigeration unit, the temperature sensor is removed from its seat, and the door seal is installed around the door perimeter. We check defrost by the heater, timer, and evaporator sensor: most often one of these elements fails, and replacing it brings the freezer back to normal. Our mobile technician arrives within 60 minutes anywhere in the city, so 'at home' here doesn't mean 'quick and dirty.' In my opinion, such jobs are better done on the spot: no need to defrost and transport the freezer.
Compressor replacement, circuit soldering, and complex control module repair require service conditions, so we carefully transport such equipment. The compressor is replaced with unsoldering and subsequent refrigerant recharge, the control module is tested separately, and the circuit is checked for leaks after soldering. After reassembly, the technician checks whether the unit holds temperature with the door closed and doesn't go into an endless cycle. Such a check reveals leaks and assembly errors before returning the equipment to the owner, so there's no need to rush the technician with the handover. We are a direct contractor, not an intermediary: repairs are done by our technicians, so we are responsible for the result. Before sending to the service center, ask the technician which units he plans to open — this helps understand why the freezer can't be fixed on site.
Repair on a balcony or in an unheated room is possible, but the technician needs to consider the ambient temperature: some work and checks can't be done in the cold. Circuit soldering and refrigerant charging require above-zero temperatures, otherwise the joint material behaves unpredictably and moisture from the air enters the system. Control module diagnostics are also performed in a warm place so the electronics don't give false readings. If the freezer is in an unheated area, don't load it with food immediately after repair — let the equipment reach operating mode in the conditions where it will work permanently. Practical tip: before the technician arrives, clear access to the freezer and remove unnecessary items from it — on a cramped balcony this saves time on disassembly and checking.
The path from request to a working freezer consists of clear steps, and at each one the client understands what's happening with their equipment.
During the free diagnostics, we check the compressor and startup, circuit pressure, defrost operation and sensors, and we quote the price only after the inspection. First, the technician listens to how the motor starts, measures current and refrigerant pressure at the inlet and outlet, and checks the defrost cycle and temperature sensor readings. These measurements show where the fault is — in the compressor, a circuit leak, or the control electronics. We begin repairing Atlant freezers in Almaty with exactly this kind of inspection so we don't replace parts at random: first we confirm the cause of the fault, then we take the freezer apart. We repair Atlant freezers in Almaty only after the technician is sure of the cause. We also check how the appliance behaves on first start after sitting idle and whether it reaches operating mode again. There's no need to defrost the freezer beforehand: it's actually helpful for the technician to see how the ice is distributed before any work — that pattern makes it easier to pinpoint the fault.
It's safer to choose a direct contractor with their own technicians who quotes the price after diagnostics, not over the phone, and provides a warranty on labor. A direct contractor sends their own technician rather than passing the request to a subcontractor, so they're responsible for the result themselves. Free on-site diagnostics is a good sign: it shows the service is willing to figure out the cause first and talk money later. If a technician is ready to give an exact price before inspection, it's often a bait: the real cause comes up during diagnostics, and a cheap call turns into an extra charge on site. Ask about the scope of the warranty and whether it includes the part itself — that makes it easier to compare offers in the city and avoid paying for nothing. Ask in advance who exactly will come and handle the repair: with a direct contractor, it's the same person, and they're also responsible for the result after the component is installed.
Repairing an Atlant freezer comes down to a few clear steps: recognize the signal, confirm the cause with measurements, and choose the format of work. Below is a short summary of each stage.
29brands
Our technicians work with freezers from various brands. Choose a brand to go to its page.
Tech Service technicians repair other appliances too — with the same 1-year warranty on labour and parts.
Refrigerator Repair in Almatyfrom 3 000 ₸
Washing Machine Repair in Almatyfrom 3 000 ₸
Dishwasher Repair in Almatyfrom 3 500 ₸
Oven Repair in Almatyfrom 3 000 ₸
Cooktop Repair in Almatyfrom 3 500 ₸
Air Conditioner Repair in Almatyfrom 3 500 ₸
Boiler and Water Heater Repair in Almatyfrom 2 500 ₸
Freezer Repair in Almatyfrom 6 000 ₸
Tumble Dryer Repair in Almatyfrom 5 000 ₸
Coffee Machine Repair in Almatyfrom 2 500 ₸
Robot Vacuum Cleaner Repair in Almatyfrom 3 500 ₸
Vacuum Cleaner Repair in Almatyfrom 1 500 ₸
Microwave Oven Repair in Almatyfrom 2 000 ₸
Hair Dryer Repair in Almatyfrom 1 500 ₸
Iron Repair in Almatyfrom 3 000 ₸
Electric Kettle Repair in Almatyfrom 2 500 ₸
Mixer Repair in Almatyfrom 2 500 ₸
Multicooker Repair in Almatyfrom 500 ₸
If your refrigerator stops working, first check the outlet, the power cord, and the thermostat setting, and after defrosting let it stand for a while.
4 February 2026 · 12 minutes read
If your refrigerator isn't cooling but the light is on, the cause is usually one of the components in the cooling circuit: the compressor, thermostat…
10 December 2025 · 13 minutes read
If your dishwasher won't drain, the most common culprits are a clogged filter or drain hose; less often, it's the pump, impeller…
24 March 2026 · 12 minutes read
A washing machine can hum for many reasons, and the first thing to figure out is when the sound appears.
20 March 2026 · 12 minutes read
If your washing machine isn't filling with water, the most common culprits are a closed valve, a clogged inlet filter screen on the hose…
20 February 2026 · 13 minutes read
If your microwave isn't heating but the light and turntable still work, the problem is usually one of the high-voltage components — the magnetron, diode…
15 February 2026 · 12 minutes read












