experience9 yearsRuslan Ts.
Washing machine and refrigerator repair technician
City
Language
What broke
Sections
Message on WhatsApp+7 (778) 021 13 16Mon–Fri 10:00–19:00, Sat–Sun 11:00–18:00
A technician arrives within 60 minutes anywhere in the city. Free diagnostics.
Our own technicians4 to 20 years of experience




Repair prices
Below are frequent symptoms and likely causes. The technician will pinpoint the exact cause after free diagnostics.
no power, blown fuse
from7 000 ₸
unsuitable cookware, faulty inverter
from15 500 ₸
overheating, sensor failure
from5 000 ₸
overheating, faulty fan
from6 500 ₸
mechanical impact, temperature shock
from5 000 ₸
dirt, moisture
from9 000 ₸
fan, foreign object
from6 500 ₸
crack, chip, damaged cooking zone
from17 000 ₸
The table lists the 'from' price for labor, for common jobs also the 'from' price of the part, plus the time required to complete the job.
1 visittime
from 10 000 ₸cost

BeforeAfter5 steps

From request to performance check — five steps.
Describe the symptom and cooktop model so the technician brings the right tools.
The technician will arrive anywhere in the city within 60 minutes of your request.
The technician tells you which part is needed and whether it's in stock before starting work.
You approve the scope of work and the price, then the technician starts.
The technician turns on each heating zone and shows that the cooktop holds heat and responds to cookware.
The home appliance repair department in Almaty has 8 technicians with 8 to 12 years of experience.

The department has 8 specializations — they are listed on the technicians' cards.
experience9 yearsWashing machine and refrigerator repair technician
experience12 yearsGeneral household appliance repair technician
experience10 yearsField technician for washing machine and refrigerator repair
experience8 yearsExpert washing machine repair technician
experience8 yearsField refrigerator repair technician
experience8 yearsSenior washing machine repair technician
experience11 yearsDishwasher repair technician
experience9 yearsWashing machine repair technician
We reply during working hours
Describe the Beko cooktop fault — the technician will agree on a convenient visit time and give an approximate repair cost before the visit.

Warranty question? Call us
+7 (778) 021 13 167 898 reviews of repairs at TECH SERVICE in total
Марина В.Order No. 838818 · 17 January 2026
oursСервис нашёл случайно, но остался доволен. Прочитал кучу отзывов, половина — реклама, но тут вроде живые. Дамир М честно сказал, что менять, а что ещё походит. Цена не изменилась ни на тенге. Цену сказали сразу, без «ну потом посмотрим». Перезвонили, когда можно было забирать. Всё объяснили простыми словами. Мастер посмотрел, назвал причину, всё разложил по полочкам. Дали гарантию и рекомендации на будущее. Ставлю пятёрку
Максат О.Order No. 2025-6929 · 29 September 2025
oursБыла срочная поломка, нужен был мастер сегодня. Починили и дали гарантию на месяц.
Рустам А.Order No. 2021-9308 · 2 November 2021
oursПозвонил утром, к обеду уже всё решили. Прочитал кучу отзывов, половина — реклама, но тут вроде живые. Рустем Т всё объяснил и не пытался впарить лишнее
Марат Ж.Order No. TS-9107 · 28 September 2021
oursНужен был ремант, искал вариант поближе. Оформили всё официально, с гарантией. Буду советовать знакомым.
Рустам А.Order No. TS-2001-673 · 20 February 2020
oursПервый раз сюда, до этого чинился в другом месте. Дамир М принял, посмотрел и сразу сказал, что делать. Работу сделали в тот же день. Проверили при мне, показали результат. Цену сказали сразу, без «ну потом посмотрим». С чистой совестью советую.
Дарья С.Order No. ZK-2297 · 11 October 2018
oursОбращаюсь не первый раз, поэтому есть что сказать. Долго откладывал ремонт, потом всё-таки собрался. Отдельно скажу про мастера: Дмитрий Радионов — спокойный, без лишней суеты. Работу сделали в тот же день. Оформили всё официально, с гарантией. Не пришлось ничего доказывать и просить. По срокам не подвели. Диагностика заняла минут двадцать. Запчасть нашли без проблем. Для Алматы — достойный вариант.
Марат Ж.Order No. ZK-2018/730 · 28 April 2018
oursДолго откладывал, но пришлось обратиться. Хотел сначала вызвать мастера на дом, потом передумал. Отношение нормальное, без высокомерия. Вернусь, если приспичит.
Руслан Д.Order No. ZK-2017/135 · 10 October 2017
oursДолго откладывал, но пришлось обратится. Для Алматы — достойный вариант.
Андрей П.Order No. ZK-7647 · 24 January 2017
oursПозвонил утром, к обеду уже всё решили. Раис Мирзахметов принял, посмотрел и сразу сказал, что делать. Вернусь, если приспичит.
Дмитрий Л.Order No. 95578 · 3 July 2016
oursСервис нашёл случайно, но остался доволен. Приняли быстро, объяснили, что и как будет. Дали гарантию и рекомендации на будущее. Оформили всё официально, с гарантией. Проверили при мне, показали результат. Проверили на всех режимах, всё чётко.
Didn’t find the answer? Message us on WhatsApp.
Ask a questionMost often it's the cookware: Beko induction requires a base with a ferromagnetic layer and the right diameter. If the cookware is correct, the burner sensor and coil are checked — that's a job for a technician during diagnostics.
Beko induction is sensitive to thin or uneven cookware and to voltage spikes, and its electronics are more complex than those of a regular electric cooktop. That's why repairs are entrusted to a technician who specializes in induction components.
In most cases a Beko panel is repaired: the power board, coil, or touch sensor is replaced, and it works again. Replacement is only more cost-effective if the body and glass-ceramic surface are seriously damaged — the technician assesses this after diagnostics.
It depends on the model: most often the touch module itself or its ribbon cable is at fault, less often the control board. The technician checks the sensor circuit during diagnostics and replaces only the faulty component, not the entire electronics.
Yes, there is a 1-year warranty on labor and parts installed. If the component fails again during this period, the technician will determine the cause under warranty.
Stop using the cooktop immediately and unplug it from the power supply — this can be dangerous. Call a technician: they will find the cause of the short circuit or wiring fault and fix it on site.
Tech Service repairs Beko induction cookers and hobs in Almaty: our technician arrives at your home within 60 minutes or takes the appliance to our service center. Diagnostics are free, the technician quotes the price after diagnostics, and we provide a 1-year warranty on labor and parts. Technicians with 7 to 20 years of experience know error codes and induction power electronics.
A Beko induction cooktop usually reports a fault itself — with a code on the display, a flashing icon, or by refusing to heat. Let's break down what the common signals mean and when you need a technician.
| Code or signal group | What it means | What the technician checks |
|---|---|---|
| E0 | No suitable cookware on the burner | Pan bottom, heating zone |
| E2 / E3 | Overheating or temperature sensor failure | Temperature sensor, cooling fan |
| E4 / E5 | Power supply or power module fault | Board, inverter, wiring |
| E6 / E7 | Control board communication error | Ribbon cables, contacts, control unit |
| Flashing zone icon | Coil doesn't detect a load | Induction coil |
| Won't turn on | No power or protection tripped | Circuit breaker, power electronics |
If your Beko cooktop turns on but doesn't heat or shows "no cookware," the cause is usually cookware with an unsuitable bottom, less often the coil, temperature sensor, or power module. Induction only heats ferromagnetic bottoms: aluminum, copper, and thin stainless steel without a magnetic layer don't create a load, so the electronics think the zone is empty. The coil under the glass transfers the field to the pan bottom, while the temperature sensor monitors heat and cuts heating if it overheats. When the bottom is suitable but the zone still stays silent, the technician checks the coil, sensor, and power module. If you need Beko induction cooktop repair in Almaty, the technician will first confirm the cost of work after free diagnostics. Before calling a specialist, we recommend checking the pan with a magnet and moving it to another burner — that immediately shows whether the issue is the cookware or a specific heating zone.
Induction heats with a magnetic field, not a spiral element, and it breaks differently. Let's look at the key components of Beko appliances and how restoring them differs from gas and conventional electric cooktops.
In Beko induction hobs, the power components are the most vulnerable — the inverter module with IGBT transistors, the coil, and the control board, because they operate under high load. The inverter module converts direct current into high-frequency alternating current to power the induction coil, and the IGBT transistors switch this load tens of thousands of times per second and heat up more than other electronics. The control board receives signals from the sensors and sets the power, so its traces and relays also wear out. The technician explains how much induction hob repair costs after inspection — the final price depends on which component has failed. When disassembling, we first check the transistors and inspect the coil — cracks in the insulation and burnt contacts are immediately visible. Power components don't fail on their own but due to overheating, voltage spikes, or a clogged cooling fan — when replacing the inverter, we also check the cooling system, otherwise the new module will suffer the same fate.
| Hob type | What breaks | What the technician checks |
|---|---|---|
| Induction | Inverter, IGBT, coil, board | Power components and magnetic circuit |
| Gas | Burners, valves, thermocouple | Leak-tightness and gas supply |
| Conventional electric | Heating element, thermostat, wiring | Heating element and power circuit |
A cracked glass-ceramic surface on a Beko induction hob cannot be repaired — it must be replaced entirely, and this is one of the most extensive body repairs. The glass-ceramic surface supports the entire cooking zone, so sealing the crack with silicone doesn't solve the problem: under load and heat, the seam separates again, and the zone loses even heating. Replacing the glass-ceramic requires disassembling the body, disconnecting the sensors and coils, carefully transferring them to the new surface, and setting the gaps. We perform this work with electronics testing after reassembly — otherwise the crack may hide existing damage to the board. A crack is dangerous not only visually: moisture and grease get inside through it, threatening the electronics — don't delay replacing the glass.
Beko induction hob repair can be done at home or at the service center. Here's what the specialist does step by step and when in-depth diagnostics are needed.
The work starts with free diagnostics: we check the power and control electronics, the induction circuit and coils to find the faulty component before replacement. The specialist opens the case, tests the control board, inspects the inverter module for breakdown, and checks the integrity of each induction coil's winding. The touch panel is tested separately: sometimes the hob doesn't detect cookware not because of the circuit but due to a distorted sensor signal. Based on the inspection, the technician names the faulty component, explains what exactly failed, and shows it on the board. Diagnostics before replacement saves money: without it, you might easily replace a working component while the fault remains — so we first find the faulty component and then replace it. The technician quotes the cost of Beko induction hob repair after free diagnostics, once it's clear which component needs replacement.
After diagnostics, we replace the faulty component — the inverter, control board, touch panel, or glass-ceramic top — and test heating and touch response under load. The inverter module converts current for the coil, so replacing it restores the burner's heating. The control board is replaced when logic fails or the sensor errors out, and the glass-ceramic top is replaced if a crack affects operation or breaks the seal of the housing. After installation, the technician turns on each burner separately and checks heating with induction cookware that has a flat ferromagnetic bottom, then runs through all power settings. Testing under load matters more than just switching on: some defects only show up when the burner reaches full power, so we test with real cookware, not on idle.
The cost of restoration depends on which component has failed. Let's break down what goes into the price and why we only quote it after diagnostics.
The cost of restoring a Beko induction cooker depends on the nature of the fault, the component needed, and the scope of work, so the technician quotes it after free diagnostics. The inverter module, control board, and temperature sensor differ in both part price and replacement complexity: to reach the inverter, the panel is disassembled more deeply than for replacing a sensor. The final amount is also affected by how many components show deviations during testing — sometimes one symptom leads to another. The same symptom can cost differently: replacing a sensor and replacing an inverter are jobs of different scale, and the exact amount can only be honestly quoted after inspection. That's why we don't give a figure over the phone — it would still be inaccurate. We repair Beko induction cookers in Almaty at your home, and the technician quotes the cost after free diagnostics.
Diagnostics are free with us, and you can pay with Kaspi QR, Kaspi Red, card, cash, or bank transfer. The technician comes to your home anywhere in the city and checks the induction circuit, board, and sensors on site to quote the cost with a clear picture of the fault. Free diagnostics removes the main risk — paying for an inspection and hearing that restoration isn't advisable: the client makes a decision already knowing both the nature of the fault and the final amount. Diagnostics are free — this applies to any cooker inspection. Based on the results, the issue often turns out to be in one component rather than the whole panel — and then the scope of work is smaller than the owner assumed from the sound or error code.
Trust in a technician comes from the warranty, hands-on experience with Beko induction specifically, and clear terms of service. Let's break down what we guarantee, how to tell a specialist from a generalist, and why an honest scope of work is only named after diagnostics.
We give a 1-year warranty on labor and parts — this covers replacing the inverter module, the control board, and other work on the induction panel. The warranty period is the same for any component: power electronics, the touch board, and the induction coil. Our warranty covers both the procedure and the installed part — if the component fails during this period, we deal with it, not the owner. In my view, a warranty on parts is just as important as on labor: if a new component turns out to be defective, the client doesn't pay twice — that's our responsibility. The technician quotes the cost of Beko induction panel repair after free diagnostics, and the 1-year warranty on labor and parts applies regardless of the amount. So when you drop off the panel, ask whether the warranty covers the part, not just the replacement itself.
A Beko induction panel requires a technician who knows power electronics and magnetic circuits, not a generalist in gas stoves — our technicians have 4 to 20 years of experience. Induction works differently: it uses an inverter module, IGBT transistors, and an induction coil, not a regular heating element with a thermostat. A gas appliance specialist doesn't check these components and often replaces parts at random, while a dedicated technician first measures the inverter parameters and only then draws a conclusion. The cause is often in the control signal, not the heating, so a dedicated technician measures parameters first and then concludes. It's worth asking the technician directly: do you work with inverters and IGBT modules in induction panels — the answer immediately shows whether they understand power electronics.
When it comes to parts and timelines, we're honest: after free diagnostics, the technician names which component is needed — inverter module, control board, or coil — and how long the work will take, rather than promising 'in an hour' upfront. The exact time depends on the specific part, and naming it before opening the panel means guessing: you can't see from the outside whether a power transistor burned out or a sensor failed. That's why we give the plan after diagnostics, not at the door, and the owner understands in advance what is being replaced and why. A technician's visit within the city takes up to 60 minutes, and the specialist also quotes the cost of work after inspection — so no extra items end up in the bill. Our recommendation is simple: don't agree to any work until the technician explains which component they're replacing and why — this protects you from replacing working parts.
A Beko induction panel requires a technician who understands electronics, not just part replacement skills. Below is a short summary to help you decide on repairing the appliance.
31brands
We repair cooktops and other appliances. Choose a brand to go to its page.
Tech Service technicians repair other appliances too — with the same 1-year warranty on labour and parts.
Refrigerator Repair in Almatyfrom 3 000 ₸
Washing Machine Repair in Almatyfrom 3 000 ₸
Dishwasher Repair in Almatyfrom 3 500 ₸
Oven Repair in Almatyfrom 3 000 ₸
Cooktop Repair in Almatyfrom 3 500 ₸
Air Conditioner Repair in Almatyfrom 3 500 ₸
Boiler and Water Heater Repair in Almatyfrom 2 500 ₸
Freezer Repair in Almatyfrom 6 000 ₸
Tumble Dryer Repair in Almatyfrom 5 000 ₸
Coffee Machine Repair in Almatyfrom 2 500 ₸
Robot Vacuum Cleaner Repair in Almatyfrom 3 500 ₸
Vacuum Cleaner Repair in Almatyfrom 1 500 ₸
Microwave Oven Repair in Almatyfrom 2 000 ₸
Hair Dryer Repair in Almatyfrom 1 500 ₸
Iron Repair in Almatyfrom 3 000 ₸
Electric Kettle Repair in Almatyfrom 2 500 ₸
Mixer Repair in Almatyfrom 2 500 ₸
Multicooker Repair in Almatyfrom 500 ₸
If your dishwasher won't drain, the most common culprits are a clogged filter or drain hose; less often, it's the pump, impeller…
24 March 2026 · 12 minutes read
A washing machine can hum for many reasons, and the first thing to figure out is when the sound appears.
20 March 2026 · 12 minutes read
If your washing machine isn't filling with water, the most common culprits are a closed valve, a clogged inlet filter screen on the hose…
20 February 2026 · 13 minutes read
If your microwave isn't heating but the light and turntable still work, the problem is usually one of the high-voltage components — the magnetron, diode…
15 February 2026 · 12 minutes read
If your refrigerator stops working, first check the outlet, the power cord, and the thermostat setting, and after defrosting let it stand for a while.
4 February 2026 · 12 minutes read
Washing machine error codes are self-diagnostic codes that point to a specific component: drain, water fill, heating, motor, or door lock.
29 January 2026 · 13 minutes read












