experience9 yearsRuslan Ts.
Washing machine and refrigerator repair technician
City
Language
What broke
Sections
Message on WhatsApp+7 (775) 030 02 94Mon–Fri 10:00–19:00, Sat–Sun 11:00–18:00
A technician will come and fix your range hood. Free diagnostics, on-site visit within 60 minutes across the city.
Our own technicians4 to 20 years of experience




Repair prices
Below are typical symptoms and likely causes. The technician will determine the exact cause after free diagnostics.
no power or control board failure
from5 500 ₸
clogged filter or blocked air duct
from4 500 ₸
worn bearings or imbalance
from5 000 ₸
clogged drain or damaged seal
from5 000 ₸
oxidized contacts or board failure
from5 500 ₸
fan jammed or winding break
from7 000 ₸
worn brushes or interturn short circuit
from7 000 ₸
burned-out lamp or faulty
from4 500 ₸
The table lists the 'from' price for labor, for common jobs also the 'from' price of the part, plus the time required to complete the job.
1 visittime
from 9 000 ₸cost

BeforeAfter5 steps

Five steps from request to checking the range hood's operation.
Leave a request by phone or messenger, describe the symptom.
The technician will arrive anywhere in the city within an hour after confirmation.
The technician explains which components need attention and fixes the list before starting the repair.
Work is performed after you agree on the price and list of parts.
The technician demonstrates the range hood in different modes and explains how to use it after repair.
The home appliance repair department in Almaty has 8 technicians with 8 to 12 years of experience.

The department has 8 specializations — they are listed on the technicians' cards.
experience9 yearsWashing machine and refrigerator repair technician
experience12 yearsGeneral household appliance repair technician
experience10 yearsField technician for washing machine and refrigerator repair
experience8 yearsExpert washing machine repair technician
experience8 yearsField refrigerator repair technician
experience8 yearsSenior washing machine repair technician
experience11 yearsDishwasher repair technician
experience9 yearsWashing machine repair technician
We reply during working hours
Call or write in a messenger. Specify the model and symptom so the technician brings the right tools. 1-year warranty on labor and parts.

Warranty question? Call us
+7 (775) 030 02 947 898 reviews of repairs at TECH SERVICE in total
Дамир И.Order No. TS-5729 · 15 April 2026
oursРадик Т подсказал, как продлить жизнь технике. Починили и дали гарантию на месяц.
Артём К.Order No. TS-3987 · 31 January 2025
oursОсновная жалоба — не включается. Дамир М снял деталь, показал износ, вопросов не осталось. Вернули в тот же день, всё функционирует.
Гульмира С.Order No. 30853 · 23 February 2024
oursДолго откладывал ремонт, потом всё-таки собрался. Ещё утром всё работало, а к вечеру — шумит. Приехал вечером, мастер ещё был на месте. Вышло дешевле нового, что логично. Мастер показал, что меняет: двигатель. Считаю, что нашёл своего мастера. Уже полгода — ни одного сбоя.
Виктор Ф.Order No. 694927 · 19 December 2023
oursСмотрел, у кого есть запчасти на такую модель. Проверил дома — всё на месте, ничего не забыли.
Елена К.Order No. TS-3941 · 2 January 2022
oursТаңертең жұмыс істеп тұрды, кешке қарай үнсіз қалды. Жалпы әсер жақсы, кемшілік байқамадым.
Кристина Л.Order No. ZK-2021/739 · 27 January 2021
oursТелефонмен кеңес сұрадым, тегін айтты. Жұмыс сапасы жақсы, артық шуы жоқ. Асыққан адамға ыңғайлы.
Татьяна Б.Order No. TS-1808-230 · 8 May 2018
oursПовод для визита: слабо тянет. Радик Т приехал в тот же день, хотя был конец смены. Работает как раньше, придирок нет)
Индира П.Order No. 480198 · 27 February 2018
oursПрочитал кучу отзывов, половина — реклама, но тут вроде живые. Основная жалоба — шумит. Второй месяц — полёт нормальный
Санжар О.Order No. TS-7699 · 3 February 2018
oursЦена имела значение, но и гарантия тоже. Первое, что заметил: не включается. Радик Т принял, посмотрел и сразу сказал, что делать. Починили и дали гарантию на месяц.
Максат О.Order No. 309597 · 11 April 2017
oursВыбирал по отзывам в 2ГИС, времени на эксперименты не было. Симптом был очевидный: слабо тянет. Работает как раньше, придирок нет.
Didn’t find the answer? Message us on WhatsApp.
Ask a questionMost Beko range hoods don't have a display with error codes, so problems are judged by symptoms: it won't turn on, doesn't extract, or is noisy. The set of indicators depends on the model, and only diagnostics can pinpoint the exact cause.
Most often the sensor or control board is to blame: touches are falsely registered due to moisture and grease buildup on the panel. Unplug the range hood and call a technician to check the electronics.
First check the bulb itself and its contact, then the power at the socket. If the bulb is fine but there's no voltage, the cause is in the wiring or control module, and that's a job for a technician.
You can replace the bulb or wash the grease filter yourself. Repairing the motor, sensor, and control board requires disassembly and tools, so it's better to leave that to a technician.
If the motor hums steadily but extraction is weak and the filter is coated with grease, the problem is a clog. After washing the filter, extraction usually recovers, and any remaining noise points to the motor.
With faulty wiring or a control board, the appliance can overheat and spark, and accumulated grease ignites easily. It's safer to unplug the range hood until the technician arrives.
Tech Service repairs Beko kitchen range hoods in Almaty at your home or in our service center. A technician arrives within 60 minutes anywhere in the city, diagnostics are free, and you get a 1-year warranty on labor and parts. The technician gives you the price after diagnostics, and you can pay via Kaspi QR, Kaspi Red, bank card, cash, or bank transfer for companies.
A Beko range hood doesn't respond to buttons or shuts off after a second — it's not always a burned-out motor. Here's what the technician checks first and where the real cause usually is.
In Beko range hoods with a touch panel, the control board often fails; in mechanical models, it's the motor's start capacitor. The control board handles speed switching and lighting: if a trace burns out or a triac fails, the panel doesn't send a signal to the motor even though the motor itself is fine. In mechanical models, the capacitor stores charge to start the windings, and when it loses capacitance, the impeller won't spin up — you only hear a quiet hum. The technician checks the electrical circuit step by step: tests the motor windings for continuity, measures the capacitor's capacitance, and inspects the board for signs of overheating. The capacitor is replaced separately from the motor, so "won't turn on" doesn't mean "needs a new motor" — the technician first tests the windings and only then makes a conclusion.
We don't recommend taking apart a Beko range hood yourself: touch panels and boards are sensitive to static, and incorrect reassembly of the impeller brings back the noise. Even with careful disassembly, it's easy to damage the panel ribbon cable or strip the impeller mount on the shaft — then vibration adds to the failure to turn on. Our visiting technician brings tools to measure capacitor capacitance and test the board, and disassembles according to the specific model's diagram. Diagnostics at your home are free with us, so trying to save money by disassembling it yourself often costs more than one technician visit with a circuit check. Based on our workshop's experience, in most such cases the work is limited to replacing the capacitor or repairing the board, not buying a new motor.
Unusual noise in a Beko range hood almost always comes from one of three components — the motor, the bearings, or the impeller. Here's how the technician tells them apart by sound and feel.
A burned-out Beko range hood motor won't start on any speed, hums, and shuts off after a few seconds due to winding overheating. If the winding is broken, the motor is completely silent, and with an inter-turn short, the housing gets noticeably hot after a short run. The technician checks this by starting all speeds one by one and listening: a working unit picks up speed smoothly, without dips or metallic rattling. The smell of burnt insulation and darkened varnish on the coil confirm the diagnosis even before disassembly. It's also worth ruling out the start capacitor — if it has lost capacitance, the motor hums but won't spin up, and that doesn't require replacing the motor. If the motor spins but has weak suction, the cause is more often a clogged impeller or grease filter, not the winding — the technician checks this before replacing the motor, otherwise the new part won't solve the problem.
| Component | Symptom | What we check |
|---|---|---|
| Motor bearings | Steady growing noise | Shaft play, lubrication, wear |
| Impeller | Body vibration, runout | Balance, stuck-on grease |
| Grease filter | Noise when airflow drops | Clogged mesh |
| Charcoal filter | Muffled sound, weak extraction | Replacement interval, saturation |
Recurring noise after service usually means the impeller was reassembled without balancing, or worn bearings weren't replaced together with the motor. New windings on an old shaft handle the load differently, and within a few weeks the play comes back with double the force. In our practice, a common mistake is installing the motor without checking the impeller seat: a misalignment of a couple of millimeters causes the body to vibrate at high speed. The second source of hum is loose fasteners holding the body to the wall: vibration travels into the wall and sounds like a motor fault. We start by cleaning the impeller and replacing the filter, and only if the hum persists do we disassemble the motor and check the bearings — so the client doesn't pay for an unnecessary replacement. We provide a 1-year warranty on labor and parts, so if the noise returns due to our work, we fix it free of charge, but it's important that the technician checks the entire assembly on the first visit, not just the obvious breakdown.
A Beko range hood may extract worse than usual, blow air back from the ventilation, or turn on at night without a command. Each symptom has its own cause — from a clogged air duct to the touch panel.
Backflow from the ventilation occurs when the check valve is stuck, broken, or missing, and the range hood is off at that moment. In Almaty high-rises, the shared shaft creates a pressure difference, and without a sealed flap, air from neighboring floors comes into the kitchen. A valve with two flaps on an axis holds the pressure due to the weight of the flaps — when contaminated with grease, they stop closing. On Beko range hoods with a plastic damper, the flaps deform over time from hot air and warp. If the mechanism is working but movement is still backward, the cause may be the building's shared ventilation shaft — then the technician selects a damper with a tighter fit. It's easy to check: hold a sheet of paper to the grille with the range hood off — if it's pulled toward the shaft, the draft is working against you.
If a Beko range hood turns on by itself or doesn't switch speeds, the cause is usually the touch panel or control board, not the apartment's wiring. Moisture and grease condensate get on the sensor tracks, and it sends false commands — the backlight turns on at night without touch. On the control board, this symptom is caused by a blown triac or a cracked solder joint in the power circuit: speed stops switching or only one works. On models with mechanical buttons, a similar symptom is caused by a stuck switch — we check the panel before replacing the unit to avoid changing a working board. In our practice, the sensor is at fault more often than the board in about two out of three cases, so we start by testing the ribbon cable and contacts.
We repair Beko range hoods at your home or at our service center, whichever is more convenient for you. Here's what a service visit involves and what the technician does at each step.
We fix most Beko range hood breakdowns right at your home: replacing the capacitor, bearings, filter, or lamp and cleaning the impeller doesn't require a workshop. The technician brings common parts for popular models—chimney, built-in, and telescopic hoods. This kind of Beko range hood repair in Almaty fits into a single visit: disassembling the housing, diagnosing the faulty component, installing the part, and testing all speeds. We only take the appliance to the service center if the control board or motor needs replacing with complex housing disassembly—we'll let you know after diagnostics. In my opinion, there's no point in hauling a range hood to a workshop for a bearing or a clogged impeller: on site you can see both the wall mounting and the condition of the air duct, which is harder to check in a workshop.
The technician arrives within 60 minutes anywhere in the city, and the work itself usually fits into one visit—the exact time depends on the component and the Beko range hood model. Replacing a capacitor or lamp is faster than overhauling the motor with bearing replacement, which requires fully disassembling the impeller. Access to the housing also affects the time: a built-in model in a wall cabinet requires careful removal, while a chimney hood is easier to take down. If we don't have the needed part on hand, we'll schedule a second visit separately—so it's important to provide the exact model during diagnostics so the right component can be brought right away. Almaty apartments with narrow air ducts often add duct cleaning work, and that's worth considering when planning.
Warranty, diagnostics, and who exactly will come to your call—these are the three questions we hear most often before a Beko range hood repair. Here are the facts based on our work.
We provide a 1-year warranty on labor and parts, including the replaced motor, capacitor, and control board of the Beko range hood. If the component acts up again—hums, doesn't reach full speed, or doesn't respond to buttons—you go back to the same technician and don't start troubleshooting from scratch. The warranty period is the same for both the control board and the motor: both are power components where an installation error shows up in the first weeks. The warranty covers the specific component we worked on, so if you report the same issue again, we first check the replaced part rather than looking for a new fault throughout the housing. This saves time for both you and us—no need to disassemble the entire hood again.
Our diagnostics are free: a technician comes out, finds the cause, and only then quotes the cost of the work. A city visit takes up to 60 minutes, so we check the Beko range hood on site without taking it to the workshop. First, the technician listens to the motor at different speeds, checks the airflow, and inspects the filters, then tests the capacitor and control board — these are the parts that most often fail or cause humming. The price is given after the inspection, once the cause is identified. The customer can decline the work based on the diagnostic results — they then know exactly what's wrong and don't pay for the visit itself. In my view, this is fairer than charging for a blind inspection: you pay for fixing the problem, not for the visit itself.
We've gathered in one place what we most often explain to range hood owners during home visits: how diagnostics begin, where noise comes from, and why airflow drops for reasons other than the motor.
32brands
The website has pages by brand. Choose your brand to go to the relevant section.
Tech Service technicians repair other appliances too — with the same 1-year warranty on labour and parts.
Refrigerator Repair in Almatyfrom 3 000 ₸
Washing Machine Repair in Almatyfrom 3 000 ₸
Dishwasher Repair in Almatyfrom 3 500 ₸
Oven Repair in Almatyfrom 3 000 ₸
Cooktop Repair in Almatyfrom 3 500 ₸
Air Conditioner Repair in Almatyfrom 3 500 ₸
Boiler and Water Heater Repair in Almatyfrom 2 500 ₸
Freezer Repair in Almatyfrom 6 000 ₸
Tumble Dryer Repair in Almatyfrom 5 000 ₸
Coffee Machine Repair in Almatyfrom 2 500 ₸
Robot Vacuum Cleaner Repair in Almatyfrom 3 500 ₸
Vacuum Cleaner Repair in Almatyfrom 1 500 ₸
Microwave Oven Repair in Almatyfrom 2 000 ₸
Hair Dryer Repair in Almatyfrom 1 500 ₸
Iron Repair in Almatyfrom 3 000 ₸
Electric Kettle Repair in Almatyfrom 2 500 ₸
Mixer Repair in Almatyfrom 2 500 ₸
Multicooker Repair in Almatyfrom 500 ₸
If your dishwasher won't drain, the most common culprits are a clogged filter or drain hose; less often, it's the pump, impeller…
24 March 2026 · 12 minutes read
A washing machine can hum for many reasons, and the first thing to figure out is when the sound appears.
20 March 2026 · 12 minutes read
If your washing machine isn't filling with water, the most common culprits are a closed valve, a clogged inlet filter screen on the hose…
20 February 2026 · 13 minutes read
If your microwave isn't heating but the light and turntable still work, the problem is usually one of the high-voltage components — the magnetron, diode…
15 February 2026 · 12 minutes read
If your refrigerator stops working, first check the outlet, the power cord, and the thermostat setting, and after defrosting let it stand for a while.
4 February 2026 · 12 minutes read
Washing machine error codes are self-diagnostic codes that point to a specific component: drain, water fill, heating, motor, or door lock.
29 January 2026 · 13 minutes read












