Open until 19:00+7 (778) 021 13 16Call a technician
Tech Service technician next to a dishwasher

AEG Dishwasher Repair in Almaty

A technician arrives within 60 minutes anywhere in the city. Free diagnostics, 1-year warranty on labor and parts.

  • 1-year warranty on labor and parts
  • Arrival within 60 minutes anywhere in the city
  • Free diagnostics

Our own technicians4 to 20 years of experience

Radik T.Ruslan Ts.Damir M.Dilmurat S.

Repair prices

  • Diagnostics0 ₸
  • Filter cleaningfrom4 500 ₸
  • Spray arm (rocker) cleaningfrom4 500 ₸
  • Door seal replacementfrom5 000 ₸
  • Temperature sensor replacementfrom5 000 ₸
All prices
2ГИСЯours4,97 898 reviews
2GIS · Google · Yandex · order database
Common faultsCommon faultsTECH SERVICE02

Common AEG dishwasher faults in Almaty

Below are common symptoms and likely causes. The technician will pinpoint the exact cause after a free diagnostic.

PricesPricesTECH SERVICE03

How much AEG dishwasher repair costs in Almaty

The table shows prices for AEG dishwasher repair: a starting labor cost without parts and the timeframe. The technician confirms the final total before any work begins.

Filter cleaningexact price — after the free diagnostics

1–2 hours

from4 500 ₸

Spray arm (rocker) cleaningexact price — after the free diagnostics

1–2 hours

from4 500 ₸

Door seal replacementparts not included

1–2 hours

from5 000 ₸

Temperature sensor replacementparts not included

1–2 hours

from5 000 ₸

Door hinge repair or replacementparts not included

1–2 hours

from5 000 ₸

Before and afterBefore and afterTECH SERVICE04

Before and after AEG dishwasher repair in Almaty

Water level sensor not triggering

1 visittime

from 6 500 ₸cost

Problem
The AEG dishwasher was taking too long to fill with water and stopped with a fill error, although water was entering the tank.
What we did
The technician removed the side panel, disconnected the tube and wires, replaced the pressure switch due to a worn diaphragm, and reconnected everything.
Result
Water filling and wash start were checked — the machine works, 1-year warranty on labor and parts.
I want the same
Built-in dishwasher in a niche of white cabinets, door open, racks inside. A technician in an orange shirt, kneeling on the right, holds a new water level sensor with a tube; the old one lies on a towel.BeforeAfter
01 / 04
All repairs
TECH SERVICE mobile technician with a tool case

How AEG dishwasher repair works at your home in Almaty

Five steps from request to final check. Diagnostics are free.

  1. Requestsame day

    Submit a request and the technician will come.

  2. Arrivalwithin 60 minutes

    The technician arrives within 60 minutes anywhere in the city.

  3. Approvalbefore work starts

    The technician explains the options and waits for your confirmation before starting work.

  4. Repairafter approval

    Work is carried out after your approval.

  5. Checkafter repair

    The technician runs a test cycle and checks water fill and drain together with you.

Leave a request
TechniciansTechniciansTECH SERVICE05

Our AEG dishwasher repair technicians in Almaty

The home appliance repair department in Almaty has 8 technicians with 8 to 12 years of experience.

  • 8 technicians in Almaty
  • 8–12 years of experience in the department
  • Article author Ruslan Ts., 9 years of experience
Technician repairing a dishwasher at a customer’s home
Field technician at a customer’s home

The department has 8 specializations — they are listed on the technicians' cards.

01 / 05
Radik T., dishwasher repair technicianexperience11 years

Radik T.

Dishwasher repair technician

Ruslan Ts., washing machine and refrigerator repair technicianexperience9 years

Ruslan Ts.

Washing machine and refrigerator repair technician

Damir M., general household appliance repair technicianexperience12 years

Damir M.

General household appliance repair technician

Dilmurat S., field technician for washing machine and refrigerator repairexperience10 years

Dilmurat S.

Field technician for washing machine and refrigerator repair

Dima, expert washing machine repair technicianexperience8 years

Dima

Expert washing machine repair technician

We reply during working hours

Book AEG dishwasher repair in Almaty

If water still won't drain after checking the filter and hose and a puddle appears, further attempts may make the problem worse. The technician will run diagnostics and identify the cause.

TECH SERVICE administrator replying to a customer's WhatsApp message

Warranty question? Call us

+7 (778) 021 13 16
Customer reviewsReviewsTECH SERVICE06

Reviews of AEG dishwasher repair in Almaty

Жанна О.Order No. 677169 · 27 June 2024

ours

Симптом был очевидный: не моет. Дамир М возился с этим дольше, чем планировал, но довёл до конца. Внешне как новый, если не считать мелкой царапины.

Repair: dishwasher

Жанна О.Order No. 2023-2100 · 12 January 2023

ours

Радик Т объяснил причину так, что понял даже я. Мастер показал, что меняет: помпа. Второй месяц — полёт нормальный!!

Repair: dishwasher

Нурасыл М.Order No. 949986 · 21 December 2022

ours

До этого обращался в другой сервис, там только развели руками. Оставил заявку на ремонт посудомоечной машины. Повод для визита: не сливает. Сказали 12 500, я согласился без торга. Разобрали, посмотрели: тэн. Внешне как новый, если не считать мелкой царапины.

Repair: dishwasher

Максим Ю.Order No. TS-1903-423 · 26 July 2019

ours

Нужен был счёт и чек, у нас техника на балансе организации. Руки чесались починить самому, хорошо, что не полез. Основная жалоба — течёт. Радик Т подсказал, как продлить жизнь технике. Отдал 13 500, и это вместе с работой. Поставили новую деталь: помпа. Приняли, выдали квитанцию, всё по-человечески. Tech-service посоветовали в чате дома, спасибо им. Достойно. Крутит ровно, без рывков.

Repair: dishwasher

Юлия А.Order No. 87230 · 8 May 2018

ours

Поломка застала перед командировкой, тянуть было нельзя. Ребёнок уже проверил на прочность, держится

Repair: dishwasher

Евгений М.Order No. TS-1809-691 · 27 April 2018

ours

Было важно, чтобы сделали до выходных — гости, то-сё. Первое, что заметил: не моет. Второй месяц — полёт нормальный.

Repair: dishwasher

Игорь Щ.Order No. 2017-7130 · 18 September 2017

ours

Алдымен интернеттен іздедім, кейін таныстарым осы жерді ұсынды. Енді басқа жерге бармаймын)

Repair: dishwasher

Ержан А.Order No. ZK-4188 · 28 June 2017

ours

Пробовал найти мастера в своём районе, но все были заняты. Отдал мастеру: посудомоечная машина. Повод для визита: течёт. Приняли без очереди, оформили за пять минут. Уже полгода — ни одного сбоя

Repair: dishwasher

Гаухар Н.Order No. ZK-9933 · 24 March 2017

ours

Симптом был очевидный: не сливает. Радик Т не стал навязывать дорогую запчасть, поставил нормальную. Проверили на всех режимах, всё чётко.

Repair: dishwasher

Санжар О.Order No. 875213 · 19 July 2016

ours

Радик Т всё объяснил и не пытался впарить лишнее. Посмотрели, назвали срок — два дня. Сказать, что доволен — ничего не сказать.

Repair: dishwasher
See all reviews
Questions and answersQuestionsTECH SERVICE07

Questions about AEG dishwasher repair in Almaty

Didn’t find the answer? Message us on WhatsApp.

Ask a question
Which brand makes the best dishwasher?

There's no clear winner: AEG, Bosch, Siemens, and Electrolux each have their strengths, and a lot comes down to the specific model and how you care for it. For repairs, what matters more is how available parts are and how often the appliance breaks down.

How long do dishwashers last?

With careful use, a dishwasher can last several years, but the exact lifespan depends on the model, water hardness, and regular maintenance. Cleaning the filters and spray arms noticeably extends the life of AEG components.

Why won't my AEG dishwasher drain even though the pump is humming?

If the pump is humming but water isn't draining, it's most often a clogged drain filter, hose, or pump impeller. Less commonly, the problem is the pump itself or the water level sensor. A technician will check these components on site.

My AEG dishwasher shows error i30 — what does it mean, and can it be fixed at home?

The i30 code indicates a drainage problem: a clog, a faulty drain pump, or a water level sensor issue. A technician will determine the exact cause after diagnostics. Many such faults can be fixed on site.

My AEG isn't filling with water even though the tap is open — what should I check first?

First, check that the valve on the inlet hose is open and the hose isn't kinked. If that doesn't help, the cause may be the inlet valve or pressure switch. A technician will run diagnostics and replace the faulty component.

Why is there water left at the bottom of my AEG dishwasher after a wash?

Water at the bottom usually means drainage is impaired: a clogged filter, hose, or a faulty drain pump. Sometimes the water level sensor is to blame. A technician will check the drainage system and fix the cause.

Repair guideArticleTECH SERVICE08

AEG dishwasher repair in Almaty by Tech Service technicians

Radik T., dishwasher repair technician

Author: Radik T.,Dishwasher repair technician

Published
Updated

Tech Service repairs AEG dishwashers in Almaty: a technician comes to your home within 60 minutes anywhere in the city or picks up the machine for service. Diagnostics are free, we agree on the price after diagnostics, and we provide a 1-year warranty on labor and parts. Technicians with 4 to 20 years of experience know typical AEG failures and can decode error codes.

What breaks on AEG dishwashers and how it shows

AEG dishwashers show failures through specific symptoms, and the technician uses the symptom to narrow down the components even before disassembly. Below are the most common scenarios and what's behind them.

Why AEG won't drain and what the technician checks

If your AEG won't drain, we first check the filter and the drain pump impeller, then the check valve and the drain hose for blockages. A clogged filter at the bottom of the tub is the most common cause: food scraps and grease block the flow, and water stands at the bottom after the cycle. The check valve prevents dirty water from flowing back into the tub, and a kinked or clogged drain hose creates the same symptom as a failed pump. On AEG models with leak protection, the drain is connected to the drip tray, so liquid accumulated there also stops pumping out. AEG dishwasher repair in Almaty starts with the same step-by-step check of the drain components. A humming but not pumping pump usually means the impeller is jammed by a foreign object or scale, not that the pump has burned out—so don't rush to replace the part before inspection.

AEG won't fill with water or won't turn on

When there's a water fill problem, we check the inlet valve, water level sensor, and flow meter; if the machine won't turn on, we check the control board and power supply. The inlet valve opens on a command from the board, and a stuck diaphragm or a broken coil leaves the tub without water. The level sensor and flow meter measure how much water has entered, and if their readings are wrong, the machine stops the cycle early. No response to the power button is more often related to electronics or the power supply than to the motor itself. An open tap doesn't guarantee water reaches the machine: a clogged mesh filter at the inlet gives the same picture as a faulty valve, so the technician starts with the simplest thing.

AEG washes poorly, leaves film, or leaks

Film and poor washing are usually caused by clogged spray arms, hard water, and scale on the heating element, while a leak from the bottom is due to the door seal or the leak protection system. Clogged spray arm holes don't deliver water to the dishes, and the cycle runs for nothing, while hard Almaty water speeds up scale buildup on the heater. This layer weakens heating, dishes stay wet, and you blame the detergent. The door seal loses elasticity and lets water onto the floor, and a triggered leak protection blocks the machine until the cause is fixed. If the dispenser doesn't open the tablet compartment, the detergent doesn't dissolve and dishes come out dirty—this is a mechanical fault that's visible during inspection.

AEG error codes and what they mean

A signal on the display is a hint, not a verdict. It points to a group of components, and the exact cause is confirmed during free diagnostics.

AEG error i30 and other common codes

Code or indicatorWhat it meansWhich component we checkWhat the specialist does
i30Drain problemFilter, drain pump, check valveClears the system, checks the impeller
Tap indicatorNo water fillInlet valve, level sensor, flow meterChecks the water supply and valve mesh
Heating errorWater not heatingHeating element, temperature sensor, scaleChecks heating and element resistance
Board errorControl failureControl board, power supplyDiagnoses the module and contacts

How the technician identifies a control board failure

We check the control board when the machine won't turn on, freezes, or behaves erratically, and we confirm the diagnosis by checking power and response to commands. First, we measure the voltage at the module input and see if power arrives after switching on. Next, we check the response to buttons and the program cycle: if a command is sent but the actuator doesn't respond, the fault is not in the module but in the circuit leading to it. Oxidized contacts, a damaged cord, and loose connectors produce the same picture as a burnt board, so we rule them out before making a verdict. Before blaming the module, the technician dismisses simple causes — oxidation and a torn cord give similar symptoms, and replacing the board in such a case would be unnecessary. AEG dishwasher repair at home in Almaty is performed by a technician after such a check to avoid replacing a working module. Our diagnostics are free, so we check power and contacts before quoting a price.

What to do if the code reappears after repair

If the signal returns, it means the cause has not been fully eliminated or a related component is faulty, and the machine needs to be checked again. A repeated signal on the display does not always point to the same part: the sensor may have triggered due to a blockage elsewhere, and the actuator due to a loose contact. We go through the entire chain from sensor to actuator, rather than randomly replacing the part indicated by the error. It's also worth checking how the machine behaves on different programs: the fault may only appear on intensive wash or when hot water is drawn. If the signal returns after service, the 1-year warranty on labor and parts covers it, so the follow-up visit addresses the underlying cause that was not fully fixed.

Which AEG components fail most often and why

AEG has components that fail more often than others, and understanding this helps both in diagnosis and prevention. Let's look at what exactly requires attention.

AEG components that require attention

ComponentWhy it failsHow it manifests
Heating elementScale from hard waterDoesn't heat water, washes poorly
Drain pumpBlockages, foreign objectsDoesn't drain, hums
Spray armsClogged holes, depositsLimescale, weak washing
Inlet valveClogged mesh filter, wearDoesn't fill with water
Detergent dispenserMechanical wearDoesn't open the tablet
Circulation pumpBearing wear, depositsNoise during operation

Why AEG doesn't heat water

If an AEG doesn't heat water, we check the heating element, temperature sensor, and scale buildup, because the cause is almost always one of these three. A limescale layer on the coil acts as thermal insulation: the heating element takes longer to reach temperature and burns out faster, and the temperature sensor gives incorrect readings. In our practice, scale is the most common finding when customers complain about cold washing. Hard water in Almaty accelerates limescale formation, so the heating element and spray arms wear out faster than the component's rated life. The machine can wash with cold water without the owner noticing — dishes come out greasy and streaky, and there's no error on the display, so heating should be checked at the first signs of poor washing.

Loud noise or tripping the breaker

Excessive noise usually comes from the circulation pump or a foreign object in the drum, while a tripping breaker points to an insulation or power supply issue. A hum that grows toward the end of the cycle is more often linked to wear on the pump shaft bearing, and a metallic knock to a piece of glass or a bone caught in the impeller. A tripping breaker at startup indicates a heater insulation breakdown or damaged wiring: moisture on the contacts causes a leak to the body. In this situation, our technicians first test the heating element and check the integrity of the wiring insulation, then inspect the motor terminals and board connectors. If the machine trips the breaker, do not turn it back on until it has been inspected — this can make a control board or wiring fault worse.

How AEG repair works with us

Our AEG repair is built around one principle — precise diagnostics first, then approval of the work. Below is how it looks step by step and where the service takes place.

Repair at home or at the service center

We repair AEG dishwashers at home or at the workshop, and the format depends on the component: some breakdowns are fixed on site, others require disassembly at the service center. At home we handle what doesn't involve fully removing the body — we check the inlet hose, filters, hoses, level sensors, and pump contacts. At the workshop we work on the control board, circulation pump motor, heating element, and tank seals, where disassembly and access to internal components are needed. We carefully remove built-in appliances from the niche without damaging the furniture front or countertop, and after reassembly we check the connections for tightness and leaks. A built-in machine isn't always easy to pull out of the kitchen, so the technician first assesses whether the fault can be fixed without removal — this saves the owner time and preserves the kitchen set.

What free diagnostics includes

Free diagnostics includes inspecting the machine, checking components based on the symptom, and identifying the cause, and the technician quotes the cost of work only after that. First we clarify how the breakdown shows up: won't drain, won't fill, is noisy, or shows a code on the display. Then we check the relevant circuit — filter, drain pump, level sensor, heating element, wiring integrity, and control board. Based on the inspection, we name the cause and propose the scope of work, and the owner decides whether to proceed. Diagnostics are needed not only to find the fault but also to rule out unnecessary replacements: sometimes cleaning is enough rather than replacing a component, and that only becomes clear during inspection. You can decline further work after diagnostics — approval is voluntary.

How to book a technician and how long to wait

A technician arrives at your home within 60 minutes anywhere in the city, and we accept Kaspi QR, Kaspi Red, card, cash or bank transfer. We book the visit based on the symptom description: give the model, the error code from the display, and the nature of the fault — this helps us prepare for the visit. Our specialist is the direct provider, comes personally, and doesn't pass the request to intermediaries. On arrival, they perform free diagnostics, name the cause, and agree on the work, and after completion provide a 1-year warranty on labor and parts. The more accurately you describe the symptom and error code when booking, the faster the technician can bring the right parts and resolve it in one visit. If the symptom is intermittent and doesn't appear every cycle, mention that separately: the technician will choose a mode to recheck the component on site and won't replace parts at random.

Warranty, trust, and when repair is worth it

Warranty and an honest answer to whether to repair or replace the machine are what most often concern AEG owners before booking. Let's cover both points and add maintenance.

What warranty covers labor and parts

We provide a 1-year warranty on labor and parts, and it's honored by the actual technician—our own specialist, not an intermediary. For complex components, this is essential: the control board, pump, and heating element are expensive, and replacing them without a warranty becomes a gamble. Our technicians have worked with AEG for 4 to 20 years, so they know which parts in this brand fail first and what to check when replacing them. The warranty on parts is just as important as on labor: if a new component fails, the owner doesn't pay for it again during the warranty period. Before work begins, ask exactly which parts are covered by the warranty—this eliminates most disputes if the problem returns.

Repair AEG or buy a new one

Repair makes sense when one component is faulty and the machine's body is in good condition, while replacement is more reasonable when several systems are worn and the appliance is quite old. AEG's main parts are designed for long service, and a single pump or heater replacement restores the wash cycle without compromising cleaning quality. Another scenario is when the control board, pump, and heating system fail simultaneously: then the combined wear suggests the appliance has reached the end of its life. The decision should be based on the whole picture—the machine's age, the number of faulty components, and overall condition—not on a single breakdown: sometimes replacing one component extends the machine's life for a long time. During free diagnostics, the technician lists which parts need replacement—this list makes it easier to weigh both options.

How to care for your AEG to avoid frequent breakdowns

  • Filter: rinse it under water once a month—a clogged mesh forces the pump to work overloaded and leads to blockages.
  • Spray arms: remove and clean the holes from scale and food residue, otherwise water stops rinsing dishes evenly.
  • Dishwasher salt: add regularly—it protects the heating element and internal components from scale in hard water.
  • Door seal: wipe the rubber from detergent residue so it doesn't lose elasticity and leak water.
  • Dishwasher cleaner: every couple of months run an empty cycle with a descaler and degreaser—this removes deposits in the drain system, and prevention costs less than repairing the heating element and pump.

AEG dishwasher repair advice worth keeping

We've gathered the key points an AEG dishwasher owner should keep in mind: from decoding the display code to deciding when repair is no longer justified.

  • Error code: narrows the search to a specific group of components, but the exact cause is confirmed by disassembly and part inspection.
  • Common culprits: the heating element, drain pump, and spray arms suffer from scale and blockages more often than other components.
  • Symptom as a clue: "not draining" or "not heating" points to a specific group of parts, not the whole machine.
  • Prevention: regular filter cleaning and salt against scale significantly extend the appliance's life.
  • Repair or replace: decide based on the machine's age and the number of faulty components—sometimes replacement is more cost-effective.

38brands

Besides AEG, we repair other dishwasher brands in Almaty

The technician repairs dishwashers from various brands. Choose yours to see the repair details.

We also repairWe also repairTECH SERVICE09

Besides AEG dishwasher repair, we fix other equipment in Almaty

Tech Service technicians repair other appliances too — with the same 1-year warranty on labour and parts.

BlogBlogTECH SERVICE10

Worth reading before AEG dishwasher repair in Almaty

Leave a review

Choose a platform — the TECH SERVICE page will open.

2ГИС2GISGoogle MapsЯYandex Maps
Send a review with photos on WhatsApp