Open until 19:00+7 (778) 746 00 26Call a technician
Tech Service technician next to a washing machine

Candy Washing Machine Repair in Astana

A technician arrives within 60 minutes anywhere in the city. Free diagnostics.

  • 1-year warranty on labor and parts
  • 4 to 20 years of experience

Our own technicians4 to 20 years of experience

Vladimir V.Adilkhan N.Temirlan B.Miras O.

Repair prices

  • Diagnostics0 ₸
  • Inlet valve replacementfrom3 000 ₸
  • Clog removal, filter cleaningfrom3 000 ₸
  • Motor brush replacementfrom3 000 ₸
  • Pressure switch (water level sensor) replacementfrom3 000 ₸
All prices
ours5,06 127 reviews
order database
Common faultsCommon faultsTECH SERVICE02

Common Candy washing machine faults in Astana

The symptoms below help you describe the issue when you book: tell them to the technician so they bring the right parts.

PricesPricesTECH SERVICE03

How much Candy washing machine repair costs in Astana

The table lists the 'from' price for labor, for common jobs also the 'from' price of the part, plus the time required to complete the job.

Inlet valve replacementparts not included

1–2 hours

from3 000 ₸

Clog removal, filter cleaninglabour only

1–2 hours

from3 000 ₸

Motor brush replacementparts not included

1–2 days

from3 000 ₸

Pressure switch (water level sensor) replacementparts not included

1–2 hours

from3 000 ₸

Temperature sensor replacementparts not included

1–2 hours

from3 500 ₸

Before and afterBefore and afterTECH SERVICE04

Before and after Candy washing machine repair in Astana

Door closes but does not lock

1 visittime

from 3 500 ₸cost

Problem
The Candy washing machine would not start a wash: the door closed but did not lock, and after a minute a lock error appeared — the door lock mechanism had failed.
What we did
The technician bent back the edge of the seal, unscrewed two screws, removed the old lock, installed a new one, and checked the lock and the wash.
Result
The door locks, and the machine starts a wash without a lock error. 1-year warranty on labor and parts.
I want the same
Aeg washing machine: door closes but does not lock — after repairBeforeAfter
01 / 05
All repairs
TECH SERVICE mobile technician with a tool case

How Candy washing machine repair works at your home in Astana

From request to checking the work — five steps.

  1. Requeston the day of request

    We record the address and a convenient time for the technician's visit.

  2. Visit confirmationbefore the visit

    We confirm the time and suggest what to clear around the machine for access.

  3. Diagnosticson site

    The technician finds the cause and agrees the scope of work with you.

  4. Repairafter

    Work begins after the scope and price are agreed.

  5. Checkafter repair

    The technician runs a program and shows you the result.

Leave a request

We reply during working hours

Book Candy washing machine repair in Astana

Describe the fault and the machine model so the technician arrives with the right parts and can start work right away.

TECH SERVICE administrator replying to a customer's WhatsApp message

Warranty question? Call us

+7 (778) 746 00 26
Customer reviewsReviewsTECH SERVICE05

Reviews of Candy washing machine repair in Astana

5,0ours

6 127 reviews of repairs at TECH SERVICE in total

Любовь Ю.Order No. ZK-2026-929 · 21 June 2026

ours

Переезжали в новую квартиру, техника после перевозки захандрила. Позвонил жене, говорит: не отжимает. Сначала думал, что нужен паспорт, но обошлось. Ни разу не пожалел.

Repair: washing machine repair in

Назерке С.Order No. 2404-9299 · 25 March 2024

ours

Бағасын білмей тұрып, бірнеше жерге қоңырау шалдым. Әйелім «таста» деді, мен көрсетуді жөн көрдім. Нәтижесіне ризамын.

Repair: washing machine repair in

Семён Ш.Order No. TSA-99469 · 19 February 2023

ours

Раньше обращался в другой сервис, там очередь на две недели. Первое, что заметил: ошибка на дисплее. Сейчас пашет без нареканий.

Repair: washing machine repair in

Иван Н.Order No. AS-3287 · 17 August 2021

ours

Причина обращения — не сушит. Дима всё сделал при мне, за пятнадцать минут. Сейчас пашет без нареканий.

Repair: washing machine repair in

Жамиля В.Order No. 59032 · 14 December 2019

ours

Бұрын басқа жерде жөндегенмін, бірақ бұл жолы осында келдім. Алдымен интернеттен қарадым, кейін осында келдім. Жұмыс істеп тұр, шағым жоқ.

Repair: washing machine repair in

Инна Н.Order No. AS-5574 · 2 December 2019

ours

В Астане с сервисами беда, поэтому выбирал по отзывам. Думал, показалас, ан нет: не отжимает. Приняли, объяснили, что и почему, без спешки. Вытащили и показали: тэн. По деньгам вышло ровно, без сюрпризов. Скажу знакомым. Функционирует, тьфу-тьфу!!

Repair: washing machine repair in

Анастасия Т.Order No. ZK-2018-535 · 20 March 2018

ours

Было важно успеть до конца недели, а то морозы обещали. Первое, что заметил: течёт. Полёт нормальный.

Repair: washing machine repair in

Вера Э.Order No. AST-1703-745 · 15 July 2017

ours

С чем обратился: не греет воду. Дима сам позвонил и сказал, что готово. Гудит ровно, не перегреваеться.

Repair: washing machine repair in

Георгий З.Order No. AST-1702-255 · 4 May 2017

ours

Позвонил в четыре места, тут ответили по-человечески. Симптом как на ладони: ошибка на дисплее. Ни разу не пожалел.

Repair: washing machine repair in

Фёдор Б.Order No. 87118 · 22 September 2016

ours

Выбирал между официальным и этим, выбрал этот. С этим и пришёл: не отжимает. Сейчас пашет без нареканий

Repair: washing machine repair in
See all reviews

Our technicians in Astana

01 / 05
Vladimir V., senior washing machine technicianexperience10 years

Vladimir V.

Senior washing machine technician

Adilkhan N., washing machine installation technicianexperience16 years

Adilkhan N.

Washing machine installation technician

Temirlan B., washing machine repair technicianexperience12 years

Temirlan B.

Washing machine repair technician

Miras O., washing machine board repair technicianexperience10 years

Miras O.

Washing machine board repair technician

Questions and answersQuestionsTECH SERVICE06

Questions about Candy washing machine repair in Astana

Didn’t find the answer? Message us on WhatsApp.

Ask a question
How can I tell if the drain pump on my Candy has failed rather than the filter being clogged?

First check the filter at the bottom front behind the service flap: if it's clean and water still stands, then look at the pump. On a working pump the impeller spins freely; on a jammed one it doesn't, and then it's replaced.

Why does my Candy washing machine stop mid-cycle and not spin?

Most often the cycle stalls due to drainage problems, an unbalanced load in the drum, or motor wear—the control board less often. A technician checks these components one by one and matches the code on the display with the table for your model.

Why is water leaking from the bottom of my Candy, and how can I tell if it's the hoses, the pump, or the door seal?

If there's a puddle under the machine, check the hoses, drain pump, and lines; a wet trail at the front by the door points to the seal. The technician finds the exact cause during disassembly, and it depends on the model.

Can the heating element in a Candy be replaced without removing the tub?

Yes, on most Candy models the heating element is replaced without removing the tub—it's accessible through the side panel. If the water isn't heating, the cause could also be the temperature sensor, which the technician confirms on site.

Do you repair compact Candy Aquamatic washing machines?

Yes, these models are also repaired, but access to components is tighter, so it's important for the technician to know the model. Diagnostics are free, and the warranty on labor and parts is 1 year.

What should I do if my Candy washing machine won't drain and shows an error?

Unplug the Candy and drain the water through the emergency hose behind the service flap at the bottom front, placing a towel down first—the water may be hot. Then call a technician—they'll check the filter, hose, and pump, and match the error code with the table for your model.

Repair guideArticleTECH SERVICE07

Candy washing machine repair in Astana by Tech Service

Vladimir V., senior washing machine technician

Author: Vladimir V.,Senior washing machine technician

Published
Updated

Tech Service repairs Candy washing machines in Astana with its own technicians: arrival within 60 minutes anywhere in the city, free diagnostics, 1-year warranty on labor and parts. The technician comes to your home or takes the machine to the service center, and gives the price after diagnostics. Technician experience ranges from 4 to 20 years.

Why your Candy won't drain and what the drain error means

Draining is the most common reason people call us about this brand. Let's break down what the drain signal means, the three parts we check first, and what you can do before the technician arrives.

What the E18 or F18 error means on a Candy

We read E18 or F18 (d02 on some models) as a drain problem, but the code's meaning depends on the model, and the technician checks it against the table for your machine. The code itself points to a part rather than giving a ready diagnosis: on different Candy generations the same combination can refer to the pump, the hose, or the water level sensor. On models without a display, the code is shown by indicators, and you decode them using the table for that specific series. The same set of symbols on different Candy generations often points to different parts, so "treating it from a picture on the internet" without checking the table risks replacing a working part and ending up with the same fault after a few washes. Accuracy matters here, not guesswork. And the drain error alone isn't a death sentence for the pump: most often a clog is to blame, and that's found on site in a couple of minutes.

Filter, hose, or pump — what we check first

  • Drain filter: we unscrew the cap at the bottom front behind the service panel and pull out coins, lint, and small items — a clog here is most often what stops water from leaving the drum.
  • Drain hose: we check whether it's kinked, whether there's a blockage inside, and whether the corrugated hose is raised correctly toward the drain — a bend or sag blocks flow just as reliably as a clogged filter.
  • Drain pump: we check whether the impeller spins freely; a multimeter won't show a jammed part, and debris (coins, lint, small items) and a clogged filter are the main causes of pump failure — scale has nothing to do with pump wear.

What you can do before the technician arrives

  • Power: unplug the machine before doing anything with water or parts — this is the first step, even before checking the filter.
  • Emergency drain: open the hose cap behind the service panel at the bottom front and drain the water into a basin with a towel underneath — the flow can be hot, so don't put your hands under the stream.
  • Filter: don't unscrew it "on the fly" and don't take the pump apart — with leftover water and pressure, it's easy to damage the impeller or flood the neighbors downstairs.
  • Check after draining: run a spin cycle on its own — if the water drains but the machine stops at the same stage again, the cause is deeper than the filter, and you'll need a technician.
  • Technician: call a specialist if the water drains but the machine stops at the spin cycle again — the cause is deeper than the filter.

Other common Candy faults and their first causes

Besides drain problems, Candy owners complain about water filling, spinning, leaks, and heating. Each symptom has two or three likely causes, checked in order — from simple to complex.

Candy won't fill with water — tap, mesh, or valve

When it "won't fill," we check in order the water supply tap, the mesh in the inlet hose, and the inlet valve — these are the three causes that trigger the E17 or F17 error (water not filling within the allotted time). First we open the tap fully and make sure the water isn't shut off at the riser. Then we remove the inlet hose and inspect the mesh: rust and sand block the opening, and the valve closes without water. If the tap and mesh are clean, we check the inlet valve itself — the coils and diaphragm movement. For this symptom in Astana, the work most often ends with cleaning the mesh. A clogged mesh looks like a "valve failure," so we remove and rinse it first rather than replacing the part blindly. Candy washing machine repair in Astana for this symptom usually starts with checking the water supply and the mesh.

Candy won't spin the laundry and stops mid-cycle

When a Candy washing machine won't spin, we start with an unbalanced load and drainage issues, then move on to the drive belt and motor. If the machine stops mid-cycle, the drain, imbalance, or motor are usually to blame, while the control board is one possible cause but not the main one. A single large item can bunch up in the drum and block spinning — rearrange the laundry and run the spin again. A clogged filter or pump leaves water in the drum, and the Candy won't advance to the spin cycle. The drive belt is checked for tension and wear, the motor for free rotation, and if the machine stops mid-cycle, the technician first checks the code on the display. Candy models with an inverter motor have no brushes, so 'brush wear' is only checked on brushed motors — otherwise a specialist might look for a part that doesn't exist.

Candy leaks from the bottom or doesn't heat water

SymptomPrimary causeSecondary causeWhat we check
Leak at bottom centerHosesDrain pumpClamps and cracks in hoses
Leak at front near doorDoor sealDrain hoseSeal tension and integrity
Doesn't heat waterHeating elementTemperature sensorScale on heating element, sensor readings

Candy components and what actually gets replaced during repair

The scope of work depends on the component: some are replaced quickly, others require removing the tank and drum. Let's break down which parts on a Candy are actually replaceable and what affects the labor intensity.

Heating element replaced without removing the tank

On most brands, including Candy, the heating element is replaced without removing the tank — the technician removes the front panel to access the heater. Next to the heating element is a temperature sensor, and its readings are compared with the actual water heating: sometimes the sensor itself is at fault, not the heater. On Candy models, the front panel is removed entirely, so access to the component is gained without dismantling the tank and drum — this keeps the job in the short category. Our specialist checks both elements at once to avoid installing a new part when the sensor is fine. That's why 'not heating' is usually one of the quickest operations, and it shouldn't be delayed: a cold wash doesn't dissolve detergent and leaves residue on the inner surface.

Bearing and sealed Candy tank

Bearing replacement is the longest job: the tank and drum are removed, and if the tank is sealed, the bearing is not replaced separately. On a split-type design, the housing is unscrewed, the old assembly is pressed out and a new one installed, then the structure is reassembled and rotation checked. On a sealed design, the issue is resolved by replacing the entire tank assembly — there is simply no separate bearing operation. Signs of wear show up during spinning: humming, knocking, play when rocking by hand. The sooner the owner notices these symptoms, the lower the risk that a worn bearing will damage the shaft and require replacing the entire assembly. Our specialist first clarifies the tank type by model rather than promising to 'replace the bearing' upfront. If the tank is sealed, disassembly and pressing won't help: the housing's seal can't be restored after intervention, so the part is only available as an assembly.

What else gets replaced on a Candy and what affects the scope of work

ComponentReplacement methodWhat affects the scope of work
Drain pumpRemoved from the bottom frontAccess behind the service panel
Inlet valveReplaced as an assemblyNumber of sections by model
Drive beltRemoved from pulleysTension and pulley type
Door sealRemoved from the rimClamp attachment
HosesReplaced by lengthRouting inside the housing

How a technician finds the cause and selects a part for Candy

To avoid replacing working parts, the technician first checks the error code against the factory table for the specific generation, then selects a replacement by part number or machine code.

How a technician matches the error code to the model's table

We don't treat based on an internet code: the technician checks the value against the factory table for the specific Candy generation, because the same index on different series points to different components. For example, E18 or F18 on some d02 models means a drain problem, while on a neighboring series the same code may refer to a different circuit — the meaning depends on the machine, and it's checked against the table for yours. On units without a display, the signal is shown by indicators, and their combination is also decoded using the table, not from memory. That's why during diagnostics it's important to state the modification and, if available, show the plate with the factory designation — this shortens the path from signal to cause and reduces the risk of unnecessary replacement.

How a part is selected by part number or model code

  • Part number: the technician finds it in the catalog using the machine's designation and orders the component with the exact number, not a "similar-looking" one.
  • Machine code: if the part number is unknown, the unit is identified by the factory plate and compatible components are looked up from it.
  • Marking on the removed component: the failed part is checked against the inscription on its body — this verifies that the replacement will fit in place of the old one.
  • Verification against the manufacturer's catalog: the technician checks the found number in the Candy catalog to make sure the component fits the specific generation.

How much Candy repair costs and when the technician names the price

The technician names the cost of work after free diagnostics — before that, an exact sum can't be given because it depends on the component and scope. Our inspection is free: the specialist comes, checks the unit, and confirms the cause, rather than just repeating the code from the display. The same symptom can involve different scope — replacing a pump and replacing a bearing with tank removal differ in labor, so there's no single sum for all cases. The inspection isn't just a formality: it's where the cause and scope are confirmed, so skipping it "to save money" often leads to replacing a working component. After the scope is agreed, the technician names the price, and only then does work begin.

How Candy repair at home in Astana works and what to do before the visit

Candy repair can be done at your home or at the service center. Here's how to call a technician, how diagnostics works, how to prepare before the visit, and what warranty you get.

At home or at the service center — what to choose

We service Candy at home or at the service center — the technician comes to you and determines on site whether the machine can be fixed without transportation. Replacing the heating element, pump, hoses, and drain hose is usually done right in the apartment: these components are removed without dismantling the tank. If the job requires removing the tank and drum, for example when replacing a bearing, the technician says in advance where it's more convenient to perform the operation — at the service center, to avoid disassembling the machine in the apartment and leaving you with an open casing. Minor and medium jobs are done at home — you don't waste time transporting the equipment. Candy washing machine repair in Astana at home is convenient for most typical breakdowns, while complex operations are planned separately by the technician. In my opinion, disassembling the tank in the kitchen is an unnecessary risk for the floor and the machine itself, so we plan such operations separately. The specialist makes the decision during free diagnostics — before work begins.

How to call a technician and how diagnostics works

  • Arrival within 60 minutes: we come anywhere in the city within an hour of your request, and a technician from our own service team is on the way.
  • Free diagnostics: the technician checks the Candy components, matches the error code against the table for your model, and tells you what's wrong.
  • Approval of work: you learn the cause and the price before any work starts, and work begins only after you agree.
  • Repair and check: the technician replaces the part and runs a wash cycle to make sure the machine fills with water, drains, and spins.
  • What to prepare: describe the symptom more precisely — the code on the display, exactly when it fails to drain, whether there's a leak; that way the specialist brings the right tools and parts for your model right away.

Tech Service warranty and service terms

We give a 1-year warranty on labor and parts, accept payment via Kaspi QR, Kaspi Red, card, cash, or bank transfer for companies, and the service is performed by our own technician, not an intermediary. A direct contractor means the same person who came to you and made the diagnosis is responsible for the result, with no handoff to third parties. The 1-year warranty only works when the specialist names the cause before replacing the part — that's why we diagnose during free diagnostics, not after the replacement. The part is selected by part number or Candy model code so the new component fits your series — that's part of the work we do, not a third party. Disputes are easier to resolve when the cause is named in advance and written down. The technician gives the price after free diagnostics — before work begins.

Making sense of Candy washing machine repair

Candy repair comes down to a few recurring scenarios: the owner sees a code, checks the simple components, and then needs a technician with a code table and access to parts.

  • Draining: error E18 or F18 points to the filter, hose, and pump, but the exact code value is checked against the table for the specific model.
  • Filling and spinning: with water problems, you go from the tap and mesh filter to the valve; when spinning stops, you go from imbalance and draining to the belt and motor.
  • Components: the heating element is replaced without removing the tub, and the bearing on a sealed tub isn't replaced separately — the whole assembly is replaced.
  • Part: the part is selected by number or model code, not "by eye" based on appearance.
  • Before the technician arrives: unplug the machine and drain the water through the emergency hose behind the bottom panel, remembering that the water may be hot.

85brands

Besides Candy, we repair other washing machine brands in Astana

We work with washing machines of every brand sold in Kazakhstan — from Samsung, LG and Indesit to Beko, Haier, Artel and rare imported makes. Can’t find yours in the list? Call anyway — a technician will come and take a look.

We also repairWe also repairTECH SERVICE08

Besides Candy washing machine repair, we fix other equipment in Astana

Tech Service technicians repair other appliances too — with the same 1-year warranty on labour and parts.

BlogBlogTECH SERVICE09

Worth reading before Candy washing machine repair in Astana

Leave a review

Choose a platform — the TECH SERVICE page will open.

Send a review with photos on WhatsApp