Яна Э.Order No. 2608-7081 · 13 March 2026
oursОраз отсоветовал дорогой ремонт, предложил простой. Диагностику провели при мне, ничего не унесли в подсобку. После ремонта — как новое.
City
Language
What broke
Sections
Message on WhatsApp+7 (778) 746 00 26Mon–Fri 10:00–19:00, Sat–Sun 11:00–18:00
A technician arrives within 60 minutes anywhere in the city. Free diagnostics, 1-year warranty on labor and parts.
Our own technicians4 to 20 years of experience




Repair prices
Common Bosch washing machine issues: causes, cost, and the diagnostic step.
Clogged filter, hose, or pump
from3 000 ₸
Closed valve, clogged mesh or valve
from3 000 ₸
Imbalance, water in the tub, belt, or motor
from3 000 ₸
Imbalance, water in the tub, belt, or motor
from3 000 ₸
Hoses, pump, or connections
from4 500 ₸
Heating element or temperature sensor
from3 500 ₸
Imbalance, shock absorbers, or bearing
from5 000 ₸
Code points to drainage, fill, or heating
from4 500 ₸
The table lists the 'from' price for labor, for common jobs also the 'from' price of the part, plus the time required to complete the job.
1 visittime
from 7 000 ₸cost

BeforeAfter5 steps

From request to final check — five steps.
Submit a request and a technician will arrive within 60 minutes anywhere in the city.
The technician arrives with tools and checks the machine on site.
Before any work begins, you receive a list of repairs for approval.
The technician installs the part and checks that it fits properly.
You test the machine and accept the result.
We reply during working hours
Submit a request by phone or through the form on the website. A technician will arrive within 60 minutes anywhere in the city, and diagnostics are free. 1-year warranty on labor and parts.

Warranty question? Call us
+7 (778) 746 00 266 127 reviews of repairs at TECH SERVICE in total
Яна Э.Order No. 2608-7081 · 13 March 2026
oursОраз отсоветовал дорогой ремонт, предложил простой. Диагностику провели при мне, ничего не унесли в подсобку. После ремонта — как новое.
Ульяна Ч.Order No. AS-5524 · 13 February 2026
oursС левого берега ехать далеко, поэтому искал поближе к дому. Было ощущение, что попал на замену целиком. Основная жалоба — течёт. Ораз разрулил всё быстро. Смета — 14 500, чек дали. Нагрев в норме, посторонних звуков нет.
Эдуард К.Order No. 2511-4190 · 4 February 2025
oursБыло важно успеть до конца недели, а то морозы обещали. Сначала гуглил, потом понял — бесполезно. Первое, что заметил: не сливает воду. Рустем Т показал старую деталь, всё прозрачно. Вытащили и показали: подшипник. Посмотрели, назвали срок, уложились. Отдал 11 500 и не жалею. Стоит, работает, радует
Василий Е.Order No. 2306-8854 · 13 March 2023
oursЗимой без техники никак, поэтому тянуть было нельзя. Причина обращения — течёт. Работает, даже лучше прежнего
Шолпан Ш.Order No. AS-8962 · 6 November 2022
oursТехника көшіру кезінде істен шықты. Қабылдау тез болды, кезек жоқ. Жақсы сервис)
Денис Л.Order No. TSA-99446 · 16 July 2022
oursИскал, кто работает в субботу, у нас с женой график сложный. Позвонил насчёт промышленной стиральной машины. Причина обращения — вибрация. Вытащили и показали: тэн. На ресепшене оформили за пару минут, выдали квитанцию. Отдал 29 000 и не жалею. Ни шума, ни запаха, всё штатно)
Степан Я.Order No. ZK-2021-950 · 21 February 2021
oursЗнакомый мастер раньше здесь работал, дал номер. Нужен был ремонт стиральной машины. Первое, что заметил: течёт. Проверил на всех режимах — держит.
Валерия А.Order No. ZK-2018-673 · 23 October 2018
oursИскал, кто работает в субботу, у нас с женой график сложный. Ремонт стирально-сушильной машины заказывал впервые. Больше всего мешало: ошибка на дисплее. Приговор — тэн. Всё быстро, но без суеты. Гудит ровно, не перегревается.
Олег Х.Order No. AST-1712-946 · 25 November 2017
oursВ Астане с сервисами беда, поэтому выбирал по отзывам. Проблема ровно одна: не сливает воду. Полёт нормальный)
Олег Х.Order No. AS-1493 · 18 June 2017
oursОфис на Кабанбай батыра, технику туда и повёз. Привёз на диагностику: стиральная машина. С чем обратился: шумит при отжиме. По деньгам вышло ровно, без сюрпризов. Обошлось заменой: помпа. Диагностику провели при мне, ничего не унесли в подсобку. Скажу знакомым. Ни шума, ни запаха, всё штатно.
experience10 yearsSenior washing machine technician
experience16 yearsWashing machine installation technician
experience12 yearsWashing machine repair technician
experience10 yearsWashing machine board repair technician
experience11 yearsDishwasher repair technician
Didn’t find the answer? Message us on WhatsApp.
Ask a questionThe front panel should only be removed after unplugging the machine and draining the water: take off the top cover, unscrew the fasteners around the perimeter, and free the door seal. The procedure and fasteners vary by series, so without experience it's best to leave this to a technician.
The country of assembly is indicated by the manufacturer on the rating plate with the E-Nr and serial number. Depending on the model, the plate is located either inside the door or on the back panel, and it's also used to select spare parts.
A Bosch specialist will immediately ask for the E-Nr from the rating plate and clarify the series: older Maxx and Classixx or current Serie 2/4/6/8. They explain where the component is located and why they need to access it from the front or bottom, rather than giving generic causes.
Most Bosch breakdowns are fixed on site: clogs, pump, heating element, sensors, belt, and hoses are accessible without transporting the machine. It's taken to a service center less often, when the drum needs to be disassembled or complex bearing work is required.
Leaks from the bottom are usually caused by hoses, the pump, or connections, while the door seal leaks at the front near the door. Unplug the machine and wipe the floor to see where it's dripping from; the exact cause will be determined by a technician during inspection.
Unplug the machine and drain the water through the emergency hose behind the service flap at the bottom front, placing a towel underneath as the water may be hot. Then check the drain hose for kinks and clogs; if it's clear, the pump is likely the issue: the pump impeller should spin freely.

Author: Vladimir V.,Senior washing machine technician
Published
Updated
Tech Service repairs Bosch washing machines in Astana: our technician arrives at your home within 60 minutes or takes the machine to our service center. Diagnostics are free, 1-year warranty on labor and parts, technicians with 7 to 20 years of experience. The technician quotes the price after diagnostics.
Bosch machines tend to show the same symptoms across models. Let's break down what's usually behind "won't drain," "won't spin," "leaking from the bottom," and "not heating," and what you can check yourself versus what needs a technician.
If your Bosch won't drain, the filter, hose, or pump are usually to blame — check them in that order. The filter is at the bottom front behind the service flap: unscrew it, remove coins, lint, and small objects, then check if the pump impeller spins freely — a multimeter won't show a jammed pump. Inspect the hose for kinks and clogs along its entire length to the drain. The pump doesn't run during water intake, so "humming during drain" and "silent during fill" are different stories — don't confuse them. Pump failures are caused by debris and a clogged filter, not limescale. Bosch washing machine repair in Astana often starts with this drain check. Before inspecting, unplug the machine and drain the water through the emergency hose behind the service flap at the bottom front, placing a towel underneath: the water may be hot.
If the machine won't spin or stops mid-program, it's usually an unbalanced load, a drain issue, a drive belt, or the motor — the control board is one possible cause but not the main one. Fix imbalance by redistributing items in the drum: one heavy item can clump up and prevent spinning. Check the drain first — the program won't continue until the water is gone. Inspect the belt for stretching and cracks, and the motor for free movement and signs of overheating. Bosch EcoSilence Drive inverter motors don't have brushes, so "brush wear" doesn't apply to them — that's only for brushed motors. The technician matches the symptom to a table for your model: the same behavior across different series can have different causes.
The code on the display is a hint, not a verdict. The meaning depends on the model, so the technician checks it against a table for the specific machine. Here's the logic of codes across Bosch generations.
On current Bosch series (Serie 2, 4, 6, 8), codes appear on the display with the letter E, while on older series (Maxx, Classixx, Logixx, Avantixx) they use the letter F, and on models without a display the code is shown by indicator lights. The letter is followed by a number for the component, which helps a Bosch washing machine repair technician know where to look: drain, water intake, heating, motor. Older series often have no display at all, and then the fault is indicated by the blinking rhythm of the panel lights. You can't mix E and F codes into one list — they're codes from different generations, and the same component may be designated differently. So before diagnostics, confirm the machine's series: that determines the correct decoding table.
| Code | Generation | What it means |
|---|---|---|
| E18 or F18 (d02) | current / older | drain problem |
| E17 or F17 | current / older | water not filling within the allotted time |
| F16 | older series | door not closed |
| F19 | older series | heating problem |
| F21 | older series | motor problem |
| F23 | older series | water in the base tray (Aquastop) |
On Bosch models without a display, the code is read from a combination of flashing indicators, and we decode it using the table for the specific series, not by guesswork. The same flashing rhythm on a Maxx and a Serie 4 can point to different components, so the technician first notes the series and model number from the rating plate inside the door, then checks the combination against the code table. After that, the check follows a chain: does the pump impeller spin freely, is there a blockage in the filter at the bottom front, does water fill within the allotted time. The meaning of a code depends on the model, so we interpret the same indicator combination on a Maxx and a Serie 4 using different tables — this way we avoid replacing a working component.
To understand why the technician removes the front panel or goes in from below, it helps to know where the key components are on a Bosch. Let's look at their location and the logic of the check.
A multimeter won't show a jammed pump — we check whether the impeller spins freely; for motors, we look at whether it's brushed or inverter, and the bearing is replaced separately only if the tub is serviceable. On brushed motors, worn brushes are a common cause of stopping; inverter Bosch EcoSilence Drive motors have no brushes, so the electronics and winding are checked. The drain pump doesn't run during water fill, so its fault is looked for during the drain cycle, not at the start of the program. The pump gets clogged with debris — coins, lint, small items from pockets — and a clogged filter speeds this up. The drum bearing is replaced separately only on a serviceable tub: on a sealed tub, the tub comes as a unit. Bearing replacement is the longest job because it requires removing the tub and drum. The technician quotes the cost of washing machine repair after free diagnostics, once it's clear which component has failed.
We select Bosch parts by part number or by the E-Nr model code, and the rating plate with the E-Nr is inside the washing machine door. The part number is stamped on the component itself — it's used to verify the pump, heating element, belt or seal if the model code doesn't give a clear answer. Bosch series come in pairs: older Maxx, Logixx, Classixx and current Serie 2, 4, 6, 8 — their externally similar components may differ in mounting point and connector. Selecting by E-Nr eliminates the risk of "installing the wrong part" when an externally identical component doesn't fit or the contact doesn't match. Verifying the part number against the E-Nr eliminates the risk of taking the machine apart again and an extra technician visit.
We start with free diagnostics: a technician comes to your home or picks up the machine and takes it to the service center. Here's how it works step by step, so you know the process in advance and don't waste time on unnecessary trips.
We service Bosch both at home and at the service center: our technician comes to you or picks up the machine if the job requires removing the tub and drum. Typical issues — a clogged filter, a worn belt, a failed pump or heating element — the technician fixes on site. He also handles leaks from underneath, lack of heating, and drain errors at home. If the symptoms show that the tub and drum need to be removed, the machine can be transported to the service center: doing that much disassembly in an apartment doesn't make sense. Bearing replacement is the longest job, and we do it at the service center. We repair Bosch washing machines in Astana on this principle: first we name the scenario, then we start disassembly. We name the scenario right away, before disassembly begins. On a sealed tub, the bearing isn't replaced separately — the technician clarifies this during diagnostics.
We dispatch a technician within 60 minutes anywhere in the city — just leave a request and he'll come to your home. We take requests based on your model and symptom: won't drain, won't fill with water, won't spin, leaks from underneath. Diagnostics are free, so when the technician arrives, he first checks the error code against the table for your series, then inspects the components. You can pay via Kaspi QR, Kaspi Red, bank card, cash, or bank transfer for companies. Before the visit, it helps to have your model and the E-Nr from the sticker inside the door: this speeds up finding the part by number if the issue turns out to be more complex. If you have the E-Nr handy, the technician can match the part number from the sticker faster. Let us know in advance if your machine has a display: on models without a screen, the code is shown by indicator lights, and that changes the initial check order.
Our technicians have worked with Bosch for 7 to 20 years and know the differences between generations: where the F-codes are on older series, where the E-codes are on current ones, where the heating element is in front and where the pump is at the bottom. Older lines Maxx, Classixx, and Logixx and current Serie 2, 4, 6, 8 are built differently, and they don't share a single code table. An experienced specialist can tell a clogged filter from a worn pump by a single symptom and won't replace a component at random. A technician without experience with the brand might confuse generations and interpret the code using a generic table — so it's worth asking "which series do you service" before booking. Also ask about the direct contractor: it matters that our own technician arrives, not a middleman. We check the code against the table for your specific model, not from memory.
Warranty and payment terms are what a Bosch owner clarifies before booking a technician. Here's how our diagnostics, warranty, and pricing work.
Diagnostics are free, and the specialist names the price after them — when the cause and the needed part are clear. The cost of Bosch washing machine repair consists of labor and parts, so the technician gives the exact amount after inspection. First, he checks the component based on the symptom: if the machine won't drain, he looks at the filter behind the service flap, the hose, and the pump; if it doesn't heat water — the heating element and temperature sensor; if it stops mid-cycle — most often he looks for the cause in draining, imbalance, or the motor. Using the part number or the model code from the sticker inside the door (E-Nr), he checks which part fits your series — Maxx, Logixx, Classixx, or Serie 2/4/6/8. The exact amount depends on the component and the part, so naming it before disassembly means guessing; after inspection, the figure is tied to a specific job.
We give a 1-year warranty on labor and parts — this applies both to home visits and in-shop repairs. The term is the same for both, so you don't need to clarify where the machine was fixed: the commitment is identical. A replaced part carries the same 1-year warranty as the labor: if it fails, we replace it within that period. For you, this means a repeat failure for the same reason doesn't turn into a new charge — the part and labor remain under one commitment. The pump gets clogged with debris, the heating element builds up scale — that's why the technician checks the condition of the unit during diagnostics, before work begins.
While you wait for the specialist, some actions are safe and help avoid making the breakdown worse, while others are risky. Here's a quick guide to what you should and shouldn't do yourself.
Repairing a Bosch washing machine comes down to accurate diagnostics: understand the symptom, match the code to the machine's generation, and check the unit in the right place on the body.
85brands
We work with washing machines of every brand sold in Kazakhstan — from Samsung, LG and Indesit to Beko, Haier, Artel and rare imported makes. Can’t find yours in the list? Call anyway — a technician will come and take a look.
Tech Service technicians repair other appliances too — with the same 1-year warranty on labour and parts.
Refrigerator Repair in Almatyfrom 3 000 ₸
Washing Machine Repair in Almatyfrom 3 000 ₸
Dishwasher Repair in Almatyfrom 3 500 ₸
Oven Repair in Almatyfrom 3 000 ₸
Cooktop Repair in Almatyfrom 3 500 ₸
Air Conditioner Repair in Almatyfrom 3 500 ₸
Boiler and Water Heater Repair in Almatyfrom 2 500 ₸
Freezer Repair in Almatyfrom 6 000 ₸
Tumble Dryer Repair in Almatyfrom 5 000 ₸
Coffee Machine Repair in Almatyfrom 2 500 ₸
Robot Vacuum Cleaner Repair in Almatyfrom 3 500 ₸
Vacuum Cleaner Repair in Almatyfrom 1 500 ₸
Microwave Oven Repair in Almatyfrom 2 000 ₸
Hair Dryer Repair in Almatyfrom 1 500 ₸
Iron Repair in Almatyfrom 3 000 ₸
Electric Kettle Repair in Almatyfrom 2 500 ₸
Mixer Repair in Almatyfrom 2 500 ₸
Multicooker Repair in Almatyfrom 500 ₸
A washing machine can hum for many reasons, and the first thing to figure out is when the sound appears.
20 March 2026 · 12 minutes read
If your washing machine isn't filling with water, the most common culprits are a closed valve, a clogged inlet filter screen on the hose…
20 February 2026 · 13 minutes read
Washing machine error codes are self-diagnostic codes that point to a specific component: drain, water fill, heating, motor, or door lock.
29 January 2026 · 13 minutes read
If your washing machine won't spin, it's usually an unbalanced load, a clogged drain filter or hose, and less often the pump, belt…
19 January 2026 · 12 minutes read
If your washing machine isn't heating water, the heating element or temperature sensor is usually to blame, less often the control board or wiring.
25 December 2025 · 12 minutes read
If your washing machine won't turn on, first check the outlet, extension cord, and the circuit breaker in your panel, then the plug and power cord.
24 November 2025 · 13 minutes read












