Open until 19:00+7 (778) 746 00 26Call a technician
Tech Service technician next to a washing machine

Zanussi Washing Machine Repair in Astana

A technician will come to you anywhere in the city and find out what's wrong. Diagnostics are free, and you get a 1-year warranty on labor and parts.

  • On-site within 60 minutes anywhere in the city
  • Free diagnostics
  • 1-year warranty

Our own technicians4 to 20 years of experience

Vladimir V.Adilkhan N.Temirlan B.Miras O.

Repair prices

  • Diagnostics0 ₸
  • Inlet valve replacementfrom3 000 ₸
  • Clog removal, filter cleaningfrom3 000 ₸
  • Motor brush replacementfrom3 000 ₸
  • Pressure switch (water level sensor) replacementfrom3 000 ₸
All prices
ours5,06 127 reviews
order database
Common faultsCommon faultsTECH SERVICE02

Common Zanussi washing machine faults in Astana

Below are typical symptoms and their most common causes, from simple to more complex.

PricesPricesTECH SERVICE03

How much Zanussi washing machine repair costs in Astana

The table lists the 'from' price for labor, for common jobs also the 'from' price of the part, plus the time required to complete the job.

Inlet valve replacementparts not included

1–2 hours

from3 000 ₸

Clog removal, filter cleaninglabour only

1–2 hours

from3 000 ₸

Motor brush replacementparts not included

1–2 days

from3 000 ₸

Pressure switch (water level sensor) replacementparts not included

1–2 hours

from3 000 ₸

Temperature sensor replacementparts not included

1–2 hours

from3 500 ₸

Before and afterBefore and afterTECH SERVICE04

Before and after Zanussi washing machine repair in Astana

Door closes but does not lock

1 visittime

from 3 500 ₸cost

Problem
The Zanussi washing machine would not start a wash: the door closed but did not lock, and after a minute a lock error appeared.
What we did
The technician folded back the edge of the seal, unscrewed two screws, removed the old lock, installed a new one, and checked the locking and the wash.
Result
The door locks, and the machine starts a wash without a lock error. 1-year warranty on the work and on the parts.
I want the same
Aeg washing machine: door closes but does not lock — after repairBeforeAfter
01 / 05
All repairs
TECH SERVICE mobile technician with a tool case

How Zanussi washing machine repair works at your home in Astana

Five steps from your request to checking that the machine works.

  1. Requestright away

    We take your request and note the address so the technician can come.

  2. Technician visitwithin 60 minutes

    A technician arrives within 60 minutes anywhere in the city.

  3. Diagnosticson site

    The technician finds the cause of the breakdown and checks the machine's components.

  4. Approvalright after

    We choose the repair option and the part, and agree on the scope of work.

  5. Checkafter repair

    We check that connections are sealed and there are no leaks after reassembly.

Leave a request

We reply during working hours

Book Zanussi washing machine repair in Astana

You can book a repair by phone or through the form on the site. Have your machine model ready and describe the symptom and error code — this helps the technician bring the right tools.

TECH SERVICE administrator replying to a customer's WhatsApp message

Warranty question? Call us

+7 (778) 746 00 26
Customer reviewsReviewsTECH SERVICE05

Reviews of Zanussi washing machine repair in Astana

5,0ours

6 127 reviews of repairs at TECH SERVICE in total

Ульяна Ч.Order No. AS-5524 · 13 February 2026

ours

С левого берега ехать далеко, поэтому искал поближе к дому. Было ощущение, что попал на замену целиком. Основная жалоба — течёт. Ораз разрулил всё быстро. Смета — 14 500, чек дали. Нагрев в норме, посторонних звуков нет.

Repair: washing machine repair in

Эдуард К.Order No. 2511-4190 · 4 February 2025

ours

Было важно успеть до конца недели, а то морозы обещали. Сначала гуглил, потом понял — бесполезно. Первое, что заметил: не сливает воду. Рустем Т показал старую деталь, всё прозрачно. Вытащили и показали: подшипник. Посмотрели, назвали срок, уложились. Отдал 11 500 и не жалею. Стоит, работает, радует

Repair: washing machine repair in

Василий Е.Order No. 2306-8854 · 13 March 2023

ours

Зимой без техники никак, поэтому тянуть было нельзя. Причина обращения — течёт. Работает, даже лучше прежнего

Repair: washing machine repair in

Семён Ш.Order No. TSA-99469 · 19 February 2023

ours

Раньше обращался в другой сервис, там очередь на две недели. Первое, что заметил: ошибка на дисплее. Сейчас пашет без нареканий.

Repair: washing machine repair in

Шолпан Ш.Order No. AS-8962 · 6 November 2022

ours

Техника көшіру кезінде істен шықты. Қабылдау тез болды, кезек жоқ. Жақсы сервис)

Repair: washing machine repair in

Денис Л.Order No. TSA-99446 · 16 July 2022

ours

Искал, кто работает в субботу, у нас с женой график сложный. Позвонил насчёт промышленной стиральной машины. Причина обращения — вибрация. Вытащили и показали: тэн. На ресепшене оформили за пару минут, выдали квитанцию. Отдал 29 000 и не жалею. Ни шума, ни запаха, всё штатно)

Repair: washing machine repair in

Иван Н.Order No. AS-3287 · 17 August 2021

ours

Причина обращения — не сушит. Дима всё сделал при мне, за пятнадцать минут. Сейчас пашет без нареканий.

Repair: washing machine repair in

Степан Я.Order No. ZK-2021-950 · 21 February 2021

ours

Знакомый мастер раньше здесь работал, дал номер. Нужен был ремонт стиральной машины. Первое, что заметил: течёт. Проверил на всех режимах — держит.

Repair: washing machine repair in

Валерия А.Order No. ZK-2018-673 · 23 October 2018

ours

Искал, кто работает в субботу, у нас с женой график сложный. Ремонт стирально-сушильной машины заказывал впервые. Больше всего мешало: ошибка на дисплее. Приговор — тэн. Всё быстро, но без суеты. Гудит ровно, не перегревается.

Repair: washing machine repair in

Олег Х.Order No. AS-1493 · 18 June 2017

ours

Офис на Кабанбай батыра, технику туда и повёз. Привёз на диагностику: стиральная машина. С чем обратился: шумит при отжиме. По деньгам вышло ровно, без сюрпризов. Обошлось заменой: помпа. Диагностику провели при мне, ничего не унесли в подсобку. Скажу знакомым. Ни шума, ни запаха, всё штатно.

Repair: washing machine repair in
See all reviews

Our technicians in Astana

01 / 05
Vladimir V., senior washing machine technicianexperience10 years

Vladimir V.

Senior washing machine technician

Adilkhan N., washing machine installation technicianexperience16 years

Adilkhan N.

Washing machine installation technician

Temirlan B., washing machine repair technicianexperience12 years

Temirlan B.

Washing machine repair technician

Miras O., washing machine board repair technicianexperience10 years

Miras O.

Washing machine board repair technician

Questions and answersQuestionsTECH SERVICE06

Questions about Zanussi washing machine repair in Astana

Didn’t find the answer? Message us on WhatsApp.

Ask a question
Where can I get a Zanussi washing machine repaired in Astana?

In Astana, Tech Service repairs Zanussi washing machines at your home: a technician arrives within 60 minutes anywhere in the city. Diagnostics are free, and the warranty on labor and parts is one year.

What wears out a Zanussi washing machine?

Overloading the drum, hard water with scale, and rarely cleaning the drain filter wear the machine out fastest. Voltage surges and running without a stabilizer (if your model needs one) also do damage.

What's valuable in a broken Zanussi washing machine?

Even a non-working machine contains non-ferrous metals, electronics, and some working components that can be sold for parts. But if the breakdown is minor, repairing is usually more worthwhile than selling it for scrap.

How can I tell if a technician really knows the Zanussi brand and doesn't just fix anything?

Ask which Zanussi error codes they've dealt with and how they check the drain pump. A specialist will ask for the model and generation, since the meaning of a code depends on the model.

The Zanussi stopped draining water but the drum still spins—is it the pump or the filter?

Most likely the filter or hose is clogged; less often the pump is to blame. Check the filter behind the service flap at the bottom front, and if it's clean, you need diagnostics to pinpoint the component.

Water is leaking from the bottom of the Zanussi washing machine—is it the door seal or the hoses?

If water collects at the front by the door, the door seal is likely the cause; if it's under the machine, it's probably the hoses, pump, or lines. A technician finds the exact cause during inspection, and it depends on the model.

Repair guideArticleTECH SERVICE07

Zanussi washing machine repair in Astana by Tech Service technicians

Vladimir V., senior washing machine technician

Author: Vladimir V.,Senior washing machine technician

Published
Updated

Tech Service repairs Zanussi washing machines in Astana with its own technicians who have 4 to 20 years of experience. Diagnostics are free, the technician arrives within 60 minutes anywhere in the city, and works at your home or at the service center. We provide a 1-year warranty on labor and parts and you can pay via Kaspi QR, Kaspi Red (instalments), bank card, cash, or bank transfer for companies.

Zanussi error codes and what they mean

A code on the display is a hint, not a verdict. The meaning depends on the model, so a technician checks it against the table for the specific machine before naming the cause.

What E18 and F18 mean on Zanussi

E18 or F18 (d02 on some models) indicates a drain problem — water doesn't leave the tub within the allotted time. This code usually points to three components: the drain filter at the bottom front behind the service flap, the corrugated hose to the pump, and the drain pump itself. The filter gets clogged with lint, coins, and small items from pockets, the hose gets kinked or blocked, and the pump impeller jams from debris. The code doesn't say what exactly broke: the technician goes through the chain from simple to complex — filter, hose, pump — and only then draws a conclusion. A multimeter won't show a jammed pump, so they check whether the impeller spins freely. If the machine stops draining, unplug it and drain the water through the emergency drain hose behind the service flap at the bottom front, placing a towel underneath: the water may be hot.

How E and F codes differ and how to read them on models without a display

The letter in the code depends on the Zanussi series and generation, and on models without a display the code is shown by blinking indicators in a specific combination. Machines with a screen display the designation directly, while simpler models use a series of light flashes, and the decoding of such a series is only in the table for the specific modification. The same symptom on different Zanussi machines can look like different codes: a drain failure on one machine gives E18, on another — F18, on a third — a combination of indicators. So you need to check against the table for your exact model, not a generic online guide that mixes designations from different series. In my opinion, half the mistakes in diagnosing from a photo of a code come from this confusion between generations.

Drain codes across different brands

BrandDrain codeWhat it means
ZanussiE18 or F18 (d02 on some models)Drain problem
Samsung5E (SE, E2)Water doesn't drain
ElectroluxE20Drain disrupted
Indesit / HotpointF05Drain problem

Why Zanussi won't drain, fill with water, or spin

Most Zanussi "breakdowns" have two or three likely causes, and they need to be checked in order — from the most common and simple to the more complex.

Zanussi won't drain water — filter, hose, or pump

  • Drain filter: we start with it — it's at the bottom front behind the service flap, and that's where coins, lint, and small items most often accumulate.
  • Drain hose: we check for kinks or clogs in the corrugated hose that runs from the pump to the drain.
  • Drain pump: we get to it last — remove it and see if the impeller spins freely.
  • Debris as the cause: a clogged filter and foreign objects in the impeller are the main cause of pump failures, so cleaning the filter extends its life.
  • What a meter won't show: a multimeter won't detect a jammed pump; the technician assesses the impeller's operation by hand, not by winding resistance.

Zanussi won't fill with water or heat — what we check

If the machine isn't filling, we check the tap, the inlet filter screen, and the inlet valve. If it's not heating, we check the heating element and the temperature sensor. The inlet filter screen gets clogged with rust and sand, so water trickles in more slowly than it should; the valve may still be working but doesn't open in time when signaled. Heating fails differently: the heating element gets scaled up, burns out, or stops receiving commands from the temperature sensor, so the wash runs in cold water even though the mechanics are fine. On most brands, the heating element can be replaced without removing the drum, so this job usually doesn't take long. Also, the drain pump doesn't run while the machine is filling, so there's no point looking for the cause there.

Zanussi won't spin and stops mid-cycle

If a Zanussi won't spin, we check for an unbalanced load, the drain, the drive belt, and the motor. When the cycle stops mid-wash, the drain, an unbalanced load, or the motor are usually to blame. A load clumped into one ball prevents the drum from reaching operating speed—usually 800–1600 rpm depending on the model—and the program hangs at the spin stage. A stretched or slipped drive belt stops the drum from spinning even though the motor hums. The control module is one possible cause of a stop, but not the main one, so starting diagnostics with it isn't cost-effective for the owner or in terms of time: first we rule out the drain and the mechanics, and check the electronics last. This order of checks saves both the technician's time and your money.

How Zanussi repair differs from other brands

Zanussi is serviced on the same principles as other brands, but there are nuances with the motor, drum, and parts selection that the technician should know in advance.

Zanussi motor—brushed or inverter

Brushed motors wear out their brushes over time, while inverter motors have no brushes, so the service approach is different. A brushed motor is found on most Zanussi models with a belt-driven drum: the graphite brushes wear down, the motor starts sparking, loses speed, and the machine won't spin at high rpm. An inverter motor is mounted directly to the drum, runs quieter and lasts longer, but if it fails, it requires checking the electronics and windings rather than replacing consumables. The speed for both designs is usually 800–1600 rpm depending on the model—that's the range the technician uses when testing the spin. So 'brush replacement' isn't a universal procedure: first we determine the motor type, otherwise the work would be pointless.

Split and sealed drums—when the bearing is replaced

  • Split drum: on Zanussi with this type of drum, we can replace the bearing and seal separately without replacing the entire assembly.
  • Sealed drum: the bearing isn't replaced separately because the drum is factory-sealed and opening it would break the seal.
  • Sign of wear: a rumbling noise during spin that increases with speed, and play in the drum—a reason to check the bearing assembly.
  • Seal: we replace it together with the bearing, otherwise water will get back to the rolling elements and the assembly will fail.
  • Timeframe: bearing replacement is the longest job because it requires removing the drum and tub, and we warn about this in advance.

How a part for Zanussi is selected

We select parts by the part number or the Zanussi model code, not 'by eye' based on appearance. The part number is stamped on the component itself—pump, heating element, valve—and the model code is on the rating plate found on the door or back panel. Using this data, we verify compatibility: pumps and heaters that look identical across different series may differ in fit, connector, and power. The control module is more often repaired than replaced entirely—this is cheaper for the owner and preserves the factory settings for the specific model. In my opinion, it's precisely careful part selection by number, not by a photo from an ad, that saves the owner a repeat visit from the technician.

How Zanussi repair at home works

We repair Zanussi at your home or in our service center—whichever is more convenient for you. A specialist visit anywhere in the city takes up to 60 minutes.

From calling a technician to free diagnostics

We take your request, a technician arrives within 60 minutes anywhere in the city and runs free diagnostics to pinpoint the cause. Zanussi washing machine repair in Astana is done at your home or at our service center, depending on which part needs to be accessed. Tech Service works as a direct contractor: our own employee comes to your address, not a middleman, so they identify the problem on the spot and bring the right tools from the van. During Zanussi diagnostics, they check drainage, water intake, heating, and motor operation one by one, from simple to complex: first the filter and hose, then the pump and valve. It helps if you remember at which stage the program stopped and what the display showed. Tell us the error code and how the machine behaved when it stopped — this narrows down the search and helps the technician bring the right tool right away.

Repair at home or at the service center — what we choose

  • Most jobs: we do at your home — replacing the filter, pump, valve, heating element, belt, and door seal doesn't require moving the machine.
  • Repair at the service center: needed for bearing replacement and other lengthy work that involves removing the tank and drum.
  • Top-loading machines: also repaired at home — access to components is different, but there are no fundamental restrictions for a home visit.
  • What determines the choice: the type of breakdown and the part that needs to be accessed, not the model or the size of the cabinet.
  • Who prefers the service center: owners whose bathroom is cramped or who have no space to lay out tools and removed parts.

Post-repair check and warranty

After the repair, we check the machine for leaks and balance, and we provide a 1-year warranty on labor and parts. The check takes a separate cycle: the technician runs a program with water intake and spin, inspects the hose connections, door seal, and drain pump, and listens to how the machine reaches its spin speed — usually 800–1600 rpm depending on the model. At this stage, you can see whether the hose is seated properly and whether the seal has shifted. Balance is checked during the spin cycle: if the tank hums and shifts, the machine is re-leveled. It's better to catch this right away than a week later when a leak reaches the neighbors downstairs. Payment — any convenient method, and the 1-year warranty covers both the part and the labor.

What you can do before the technician arrives

While the technician is on the way, you can take a few safe steps. They won't replace the repair, but they'll calm you down and speed up the work on site.

How to safely drain water from a Zanussi

Unplug the machine, drain the liquid through the emergency drain hose behind the service flap at the bottom front, with a towel underneath. The emergency drain is a thin tube with a cap next to the drain filter: remove the cap and direct the flow into a low basin or cloth. On some Zanussi models, the tube is secured with a clip at the base of the cabinet, and its end comes out into the same recess. Keep the container close to the floor so the stream doesn't splash around. The water in the tank can be hot after a high-temperature wash, so don't put your hands under the stream and don't unscrew the filter 'on the fly' — drain through the tube first, then touch the cap. If the flow doesn't start, the cap may be too tight — check it before the technician arrives.

What not to do before the technician arrives

  • Don't disassemble the cabinet: without tools and experience, it's easy to damage the mounts and wiring, which will complicate diagnostics.
  • Don't remove the pump: it's checked by whether the impeller spins freely, not 'by eye', and a multimeter won't show a jammed pump.
  • Don't unscrew the filter 'on the fly': first drain the liquid through the emergency tube, otherwise it will end up on the floor.
  • Remember the error code: it will narrow down the cause, and the technician will compare the value with the table for your model.
  • Unplug the machine: a basic safety rule before the technician arrives, especially if the cabinet is wet.
  • Don't try to fix the board: the control board is just one of the reasons a cycle stops midway, and not the main one — more often it's drainage or imbalance.

Warranty, diagnostics, and terms of service

What the owner wants to know before calling a technician: how much diagnostics costs, what the warranty covers, and how payment works. We break it down step by step, with no fine print.

Free diagnostics and how the price is set

Diagnostics are free, and the technician gives you the price after them — once it's clear what exactly needs to be done with the machine. First, they check the component that stopped the appliance: the drain pump, inlet valve, heating element, or motor — and only then quote the price for labor and the part. The part is selected by its part number or model code, so availability and the specific version also affect the final cost. That's why no one quotes a price "by eye" before diagnostics: the price depends on the component and the part, not on the symptom the owner described over the phone. In my view, this is fairer: "won't drain" sounds the same whether it's a clogged filter or a burnt-out pump, but the difference in work is fundamental.

1-year warranty and payment

We provide a 1-year warranty on labor and parts and you can pay via Kaspi QR, Kaspi Red (instalments), bank card, cash, or bank transfer for companies. The warranty covers both the part and the technician's work — meaning if the same issue happens again for the same reason, the owner won't have to pay twice. This applies both for home visits and at the service center: the technician arrives with their own tools and, after replacing the component, checks the machine in all modes — water fill, wash, drain, and spin. Our technicians have 4 to 20 years of experience and work specifically with Zanussi, not with all brands. Before the visit, ask the technician which components they check first — so you'll know in advance what's included in the work and what's outside the scope of diagnostics.

Key aspects of Zanussi washer repair

Here's a quick summary of what determines the outcome of a Zanussi washing machine repair: decoding the error code, finding the cause from simple to complex, and safe steps before the specialist arrives.

  • An error code is a hint, not a diagnosis: the meaning depends on the model, so it's checked against the table for that specific machine.
  • A symptom points to two or three causes: with "won't drain," the filter, hose, and pump are checked — from simple to complex.
  • Zanussi specifics: the motor type, whether the tub is disassemblable or sealed, and selecting the part by model code determine how the service goes.
  • Safety before the specialist arrives: unplug the machine and drain the water through the emergency hose without taking the body apart.
  • Terms matter upfront: free diagnostics, a 1-year warranty, and a clear payment process answer your questions before you call.

85brands

Besides Zanussi, we repair other washing machine brands in Astana

We work with washing machines of every brand sold in Kazakhstan — from Samsung, LG and Indesit to Beko, Haier, Artel and rare imported makes. Can’t find yours in the list? Call anyway — a technician will come and take a look.

We also repairWe also repairTECH SERVICE08

Besides Zanussi washing machine repair, we fix other equipment in Astana

Tech Service technicians repair other appliances too — with the same 1-year warranty on labour and parts.

BlogBlogTECH SERVICE09

Worth reading before Zanussi washing machine repair in Astana

Leave a review

Choose a platform — the TECH SERVICE page will open.

Send a review with photos on WhatsApp