Айжан Б.Order No. 2610-7479 · 2 October 2026
oursБұл жерге бірінші рет келдім. Түскі үзіліске қарамастан қабылдады. Бағасы мен сапасы сай.
City
Language
What broke
Sections
Message on WhatsApp+7 (778) 021 11 78Mon–Fri 10:00–19:00, Sat–Sun 11:00–18:00
A technician will arrive within 60 minutes anywhere in the city. Diagnostics are free.
Our own technicians4 to 20 years of experience




Repair prices
Below are typical symptoms and likely causes. Note the model and symptom before requesting service.
heating element, thermostat, or temperature sensor
from4 500 ₸
plug, outlet, or switch
from5 000 ₸
worn contacts or sensor
from4 500 ₸
heating element or wiring
from6 000 ₸
hinges, seal, or misalignment
from3 000 ₸
drive motor or belt
from5 000 ₸
wiring, contacts, or switch
from5 000 ₸
thermostat or temperature sensor
from4 500 ₸
The table shows how much Asel oven repair costs in Astana: a "from" labor price excluding parts and the timeframe; the technician confirms the final amount before starting the repair.
1 visittime
from 6 000 ₸cost

BeforeAfter5 steps

Five steps from request to performance check.
Describe the symptom and model — the technician will prepare for the visit.
The technician will arrive anywhere in the city within an hour after your request.
The technician comes with their own tools and works on-site.
You learn the cost of repair and parts, then make a decision.
Together with the technician, check heating, grill, and door closing.
We reply during working hours
Describe the symptom and oven model — the technician will prepare for the visit and bring the necessary parts.

Warranty question? Call us
+7 (778) 021 11 786 127 reviews of repairs at TECH SERVICE in total
Айжан Б.Order No. 2610-7479 · 2 October 2026
oursБұл жерге бірінші рет келдім. Түскі үзіліске қарамастан қабылдады. Бағасы мен сапасы сай.
Зоя М.Order No. AS-4124 · 11 February 2026
oursБыло важно успеть до конца недели, а то морозы обещали. Диагностика духовки — с неё и начал. Жалоба одна: не держит температуру. По факту меняли: тэн. Сравнивал — здесь дешевле. Привезли на такси, приняли без вопросов. Не разочаровался. Работает, как будто и не ломалось.
Айбек А.Order No. TSA-49239 · 12 November 2025
oursҚыс қатты, техникасыз қиын, сондықтан тез жөндеу керек болды. Құрылғы ескі, бірақ жақсы қарайды екен. Ризамын, рахмет.
Лариса О.Order No. 23889 · 14 October 2022
oursЗнакомый мастер раньше здесь работал, дал номер. Вчера работало, сегодня уже не закрывается. Выдали номер заказа и сказали, как отслеживать. Цену держали до конца, молодцы. Тихо, ровно, без сюрпризов.
Куралай Е.Order No. AS-5526 · 28 April 2019
oursҚұрылғыны әкелдім, бірден қабылдады. Бәрі жақсы болды. Рахмет, ұсынамын.
Валерия А.Order No. AST-1801-351 · 15 December 2018
oursРадик Т показал старую деталь, всё прозрачно. Мастер сам предложил забрать технику на следующий день. Гудит ровно, не перегревается)
Георгий З.Order No. ZK-2017-132 · 17 June 2017
oursХотел вызвать на дом, но в ЖК не пускают без пропуска. Настроение было — хуже некуда. С чем обратился: не закрывается. Нужна была новая деталь: уплотнитель. 21 500, и гарантия в комплекте. Приехал без записи, но свободный мастер нашёлся. Гудит ровно, не перегревается
Борис В.Order No. AS-5125 · 29 April 2016
oursСмотрел, чтобы был свой склад запчастей, а не под заказ. Сначала списал на мороз, но нет: не закрывается. По факту меняли: уплотнитель. Выдали номер заказа и сказали, как отслеживать. Смета — 26 500, чек дали. Обращусь ещё. Вернули — проверил, всё ок.
Оксана Т.Order No. 1612-1198 · 2 March 2016
oursСосед по площадке хвалил, решил проверить. Ни с того ни с сего — не держит температуру. Нагрев в норме, посторонних звуков нет.
Фёдор Б.Order No. AS-1056 · 12 January 2016
oursХотел вызвать на дом, но в ЖК не пускают без пропуска. Настроение было — хуже некуда. Больше всего мешало: не греет. Всё быстро, но без суеты. Вскрытие показало: уплотнитель. Смета — 23 500, чек дали. Сделали так, что и не придерёшься
experience11 yearsStove and oven repair technician
experience11 yearsDishwasher repair technician
experience10 yearsSenior washing machine technician
experience11 yearsFreezer repair technician
experience16 yearsWashing machine installation technician
Didn’t find the answer? Message us on WhatsApp.
Ask a questionAt Tech Service: a technician comes to your home anywhere in the city within 60 minutes, and diagnostics are free. If you need a repair at the service center, our direct technician will handle it too, with no middlemen.
The decoding depends on the model: across different Asel series, codes indicate a faulty sensor, thermostat, or electronics. Check the code against your model's manual, and if you don't have one, don't try to clear the error at random—it's better to call a technician for diagnostics.
Most often, one of the heating elements or the mode switch has failed, and less often the wiring to it. It depends on the model: the technician will check the heating elements and the circuit on site to replace exactly the faulty component.
If the heating element doesn't heat at all or heats only partially, while the display and modes work, it's more likely the heater. When the oven turns on but the temperature fluctuates or won't hold steady, the sensor or thermostat is suspected; diagnostics will show for sure.
Yes, it's a risk: a faulty thermostat or sensor leads to overheating, melted wiring, and fire. It's better to unplug the oven and not turn it on until a technician inspects it, rather than trying to reheat your dish.
Noise and weak airflow usually mean a worn motor bearing or a clogged fan blade, and sometimes the motor itself is to blame. It depends on the model: the technician will remove the fan, check the motor, and replace the component if needed.

Author: Beknur D.,Stove and oven repair technician
Published
Updated
Tech Service repairs Asel electric and gas ovens in Astana: our technician arrives at your home within 60 minutes, diagnostics are free, and you get a 1-year warranty on labor and parts. Technicians with 4 to 20 years of experience will decode the error code, find the cause, and agree on the scope of work after diagnostics.
An Asel oven is built like most modern cabinets, but it has its own weak points. Let's break down which symptom points to which component being checked first.
Our technician first checks the heating element, thermostat, and temperature sensor—these are responsible for heating, and any of the three could be to blame for the 'not heating' symptom. In Asel, the upper and lower heaters work separately, so it's important to understand which zone is silent: if the lower heating element fails, the chamber only heats from the top, and baked goods remain raw on the bottom. The thermostat clicks but doesn't open the circuit in time, and the cabinet either overheats or doesn't reach the set mode. The temperature sensor gives incorrect resistance readings—the display looks normal, but the actual heat in the chamber is tens of degrees lower than stated. If the upper zone heats but the lower doesn't, it's almost always the lower heating element, not the thermostat; you can't confuse them during a visual diagnosis, or you'll replace a working part. If you need Asel oven repair in Astana, the technician comes to your home and starts with free diagnostics.
One side burns, the fan is noisy, or the door doesn't close properly—these are three different components: convection, seal, and hinges, and each is fixed separately. The convection fan is responsible for unevenness: over time, its impeller gets covered in grease, the bearing starts to hum, and the hot air flow goes to one side—you have to rotate the baking sheet manually so the cake bakes evenly. The door seal keeps heat inside the chamber, and when the rubber hardens and cracks, heat escapes through the gap around the perimeter, and cooking time increases. The hinges and door glass cause misalignment: the door sags, the seal weakens, and even an intact seal stops working. A worn seal quietly increases energy consumption and overloads the heating elements—replacing the rubber is often cheaper than subsequently restoring the heating element.
In gas Asel ovens, the gas part is added to the electrical part—valve, igniter, and safety solenoid valve—so diagnostics begin with checking the gas supply and ignition. The gas valve regulates fuel supply to the burner, the igniter provides the spark, and the safety solenoid valve shuts off the gas if the flame goes out. The electrical part in such models is only responsible for lighting, timer, and rotisserie, so 'no heating' in the gas version is not sought in the heating element but in the ignition circuit. The igniter gets dirty over time, the spark weakens, and ignition takes three or four attempts. If the burner goes out a few seconds after ignition, the problem is more often the flame sensor, not the nozzle—cleaning the nozzle in this case doesn't solve the problem.
The code on the display is a hint, not a verdict. Below are typical Asel failure groups, their decoding, and the owner's first steps before the specialist arrives.
| Code group | What is checked | What to do before the technician arrives |
|---|---|---|
| Temperature sensor failure | sensor and its circuit | do not heat the oven, record the code |
| Heating failure | heating element, heating relay | unplug from the mains |
| Module communication failure | ribbon cables, control board | do not disassemble the panel |
| Gas failure | valve, igniter | shut off the gas, do not ignite |
After a power surge, the control module is usually the first to suffer — it takes the hit before anything else, and there may be no visible signs at all. The display doesn't light up, the buttons don't respond, yet the heating element and thermostat often remain intact. On Asel gas models, the same surge can knock out the ignition board, and the igniter stops clicking. At Tech Service, during free diagnostics, we first check the power circuit of the unit and test the temperature sensor — these two points show whether the electronics are burned out or the problem is in the wiring. Before taking the appliance to a service center, check the circuit breaker in your panel and the outlet — sometimes a "dead" oven has simply lost power, and you don't need to call a technician.
Our Asel oven repair in Astana is set up so that most of the work happens right in your kitchen. Let's go through the steps in order — from request to checking the repaired appliance.
The technician arrives within 60 minutes, performs free diagnostics, names the cause and scope of work, and only starts after you agree. First, they check the heating, temperature sensor, and power circuit, then remove the casing and inspect the heating element, thermostat, and wiring. Based on the inspection, you get a clear picture: what failed, which parts are needed, and how much work lies ahead. Approval is mandatory: no one takes anything apart or replaces anything without your go-ahead. If the fault requires bench testing, we'll tell you right after diagnostics — taking the appliance to the service center is discussed before work begins, not sprung on you. In my view, this is the moment that most often puts the owner at ease: you know both the cause and the plan in advance.
Most Asel breakdowns — heating element, thermostat, fan, seal, light — are fixed on-site, and the appliance is taken to the service center only when bench testing of the module is needed. On-site, we replace heating elements, adjust the thermostat, eliminate fan noise, install a new door seal, and restore the light. The control module is a separate story: it's easier to test on a bench than to guess from indirect signs right in your kitchen. A built-in oven is harder to remove than a freestanding cooker, so if there's any doubt about the diagnosis, we first check everything on-site to avoid taking the appliance away unnecessarily. Freestanding models are simpler in this regard — they can be removed and prepared for transport faster. The decision to take it away is always discussed with you, never made unilaterally.
The timeline depends on which part is being replaced and whether it's in stock, so we give an exact time after diagnostics, not over the phone. Simple replacements like a light bulb or seal usually don't require a second visit, while complex components like the control module may need a second visit — it's best to clarify this right away. Access to components also affects the timeline: built-in models have more fasteners and panels that need to be carefully removed and put back. From our technicians' experience, it's more honest to give a range after inspection than to promise an exact time blindly based on a description of the breakdown. We fix the agreed scope of work and stick to it — no sudden "we found more." If a part needs to be ordered, you'll know at the diagnostics stage and can decide whether to proceed or wait.
The service center takes your request, and our own technician comes to your address, not a third-party contractor. Let us explain what that means in practice and how we stand behind the result.
Tech Service is a direct contractor: a technician comes to your home or the work is done in our service center, with no passing your request to third-party subcontractors. A dispatcher at a middleman service takes the call, looks for an available specialist, and hands over the address — but they control neither the part nor the quality of work. With us, the same person who handles your request is the one who later answers for the result, so the question "who exactly will come" is settled during the call, not on the day of the visit. A technician reaches you anywhere in the city within 60 minutes, and diagnostics are free: the specialist inspects the oven on site and only then quotes the scope of work. When you go through a middleman, responsibility for the part and the work is blurred between the dispatcher and the technician, while with a direct contractor the warranty is issued by the same provider. Ask when you book whether the technician comes from the company itself — the answer immediately tells you who you'll be dealing with.
Our technicians have 4 to 20 years of experience with appliances, and we provide a 1-year warranty on the completed work and installed parts. That kind of experience means the specialist knows the design of Asel ovens by heart: the location of heating elements, the thermostat, the control board, and the gas automation — and doesn't spend the visit studying the model from a diagram. Diagnostics are free, so inspection and troubleshooting don't add a separate stage to the job. You can pay via Kaspi QR, Kaspi Red, bank card, cash, or bank transfer for companies. The warranty covers both the part and the work — if a part fails due to our fault, a repeat visit won't cost you again. In our practice, a common cause of repeat calls is installing a part without checking adjacent components, and the warranty on work covers exactly that risk: the technician is responsible for the result as a whole, not just the replaced element.
Before calling a technician, it helps to understand what makes up the cost and when restoration really makes sense, and when it's wiser to think about replacing the appliance.
The technician quotes the cost after free diagnostics — it depends on which part is being replaced and how much work is required. Three things affect the price: the type of fault, the number of components that need to be disassembled, and how difficult they are to access. Replacing a heating element in the electric cavity and repairing the gas unit are jobs of different complexity, and they can't be priced the same. Mechanical operations and replacement of the seal or hinge are calculated separately if they're part of the job. We accept Kaspi QR, Kaspi Red, card, cash or bank transfer and quote the amount before work begins, so you can decide without surprises. Diagnostics are free, so declining work after them doesn't create extra costs — you pay only for the operations you agree to.
Repair makes sense when the fault is localized and the part is available, while replacement is worth considering if the oven cavity is seriously damaged or several components fail at once. A simple rule of thumb: one fault with a clear cause means fix it; a crack in the oven enamel, a burn-through in the wall, or simultaneous failure of heating and controls is a reason to weigh replacement. The age of the appliance alone is not a verdict—what matters more is how many components failed at the same time and whether a suitable part is available, and diagnostics reveals that. In my view, owners often replace an oven prematurely because of a single failed part that could easily be replaced: the heating element, thermostat, or door hinge can be replaced individually and get the oven working again. Free diagnostics helps determine whether repairs are justified and avoids spending money on restoring an appliance that has already served its time.
To sum up: we've gathered the key points an Asel oven owner should keep in mind—from the first symptom to the decision to repair or replace the appliance.
41brands
If you have a different brand of appliance, select it on the site — our technicians work with various brands.
Tech Service technicians repair other appliances too — with the same 1-year warranty on labour and parts.
Refrigerator Repair in Almatyfrom 3 000 ₸
Washing Machine Repair in Almatyfrom 3 000 ₸
Dishwasher Repair in Almatyfrom 3 500 ₸
Oven Repair in Almatyfrom 3 000 ₸
Cooktop Repair in Almatyfrom 3 500 ₸
Air Conditioner Repair in Almatyfrom 3 500 ₸
Boiler and Water Heater Repair in Almatyfrom 2 500 ₸
Freezer Repair in Almatyfrom 6 000 ₸
Tumble Dryer Repair in Almatyfrom 5 000 ₸
Coffee Machine Repair in Almatyfrom 2 500 ₸
Robot Vacuum Cleaner Repair in Almatyfrom 3 500 ₸
Vacuum Cleaner Repair in Almatyfrom 1 500 ₸
Microwave Oven Repair in Almatyfrom 2 000 ₸
Hair Dryer Repair in Almatyfrom 1 500 ₸
Iron Repair in Almatyfrom 3 000 ₸
Electric Kettle Repair in Almatyfrom 2 500 ₸
Mixer Repair in Almatyfrom 2 500 ₸
Multicooker Repair in Almatyfrom 500 ₸
If your oven isn't working, first check the outlet, the circuit breaker in the panel, and the selected mode, then assess the symptom: not heating…
3 October 2025 · 12 minutes read
If your dishwasher won't drain, the most common culprits are a clogged filter or drain hose; less often, it's the pump, impeller…
24 March 2026 · 12 minutes read
A washing machine can hum for many reasons, and the first thing to figure out is when the sound appears.
20 March 2026 · 12 minutes read
If your washing machine isn't filling with water, the most common culprits are a closed valve, a clogged inlet filter screen on the hose…
20 February 2026 · 13 minutes read
If your microwave isn't heating but the light and turntable still work, the problem is usually one of the high-voltage components — the magnetron, diode…
15 February 2026 · 12 minutes read
If your refrigerator stops working, first check the outlet, the power cord, and the thermostat setting, and after defrosting let it stand for a while.
4 February 2026 · 12 minutes read












