experience10 yearsMaksim S.
Graphics card repair technician
City
Language
What broke
Sections
Message on WhatsApp+7 (778) 021 35 86Mon–Fri 10:00–19:00, Sat–Sun 11:00–18:00
A technician arrives within 60 minutes anywhere in the city. Diagnostics are free.
Our own technicians4 to 20 years of experience




Repair prices
The symptoms customers most often report. The technician will pinpoint the exact cause during free diagnostics.
Dead battery, oxidized contacts
from3 500 ₸
Dirty contacts, worn drive
from3 000 ₸
Broken flex cable, lens board failure
from7 000 ₸
Worn mechanism, deformed curtains
from6 500 ₸
Dust gets in when changing lenses
from6 500 ₸
Worn lamp, faulty capacitor
from4 500 ₸
Cracked housing, stripped bayonet thread
from7 000 ₸
Damaged contacts, controller failure
from5 500 ₸
The table lists the 'from' price for labor, for common jobs also the 'from' price of the part, plus the time required to complete the job.
1–3 daystime
from 9 000 ₸cost

BeforeAfter5 steps

From request to check — five steps, including free diagnostics.
Submit a request and the technician will ask about your camera model and symptoms.
The technician arrives anywhere in the city within 60 minutes of your request.
The technician will arrange a convenient time and place for the visit — when and where to come.
The technician performs the agreed work and replaces parts.
Provide the model and serial number so the technician can bring the right parts.
The computer and laptop repair department in Almaty has 7 technicians with 6 to 15 years of experience.

The department has 7 specializations — they are listed on the technicians' cards.
experience10 yearsGraphics card repair technician
experience6 yearsPC and laptop diagnostics technician
experience8 yearsLaptop repair engineer
experience10 yearsSoftware installation specialist
experience7 yearsPC and laptop repair technician
experience13 yearsDiagnostics and virus removal specialist
experience15 yearsConsultant
We reply during working hours
1-year warranty on labor and parts. We accept Kaspi QR, Kaspi Red, card, cash or bank transfer — ask the technician about the most convenient option when you request.

Warranty question? Call us
+7 (778) 021 35 867 898 reviews of repairs at TECH SERVICE in total
Светлана Д.Order No. ZK-7953 · 22 February 2026
oursВыбирал по отзывам в 2ГИС, времени на эксперименты не было. Сначала думал, что ерунда, но появилось: ошибка карты. Приняли, выдали квитанцию, всё по-человечески. Сказали 24 000, а потом ещё и скидку сделали. Сделали аккуратно, следов разборки не видно.
Асель Ж.Order No. ZK-2022/707 · 6 October 2022
oursДамир М всё объяснил и не пытался впарить лишнее. Сказать, что доволен — ничего не сказать.
Айгерим Б.Order No. ZK-2021/813 · 23 October 2021
oursДолго откладывал ремонт, потом всё-таки собрался. Оставил заявку на ремонт объектива. Жалоба простая: не фокусируется. Разобрали, посмотрели: плата. Сделали и забыл про проблему
Ольга М.Order No. 11984 · 16 June 2021
oursХотел сначала вызвать мастера на дом, потом передумал. Больше всего напрягало: пятна на матрице. Проверили при мне, показали, что всё держит.
Акбота Т.Order No. TS-6261 · 12 October 2020
oursСимптом был очевидный: не фокусируется. Отдельно спасибо мастеру — Дамир М, терпения ему хватило. Функции все на месте, ничего не отвалилось.
Станислав К.Order No. 550081 · 4 August 2019
oursС чем пришёл: не срабатывает. Максим Снегирев снял деталь, показал износ, вопросов не осталось. Ребёнок уже проверил на прочность, держится.
Алишер У.Order No. 45437 · 23 December 2018
oursПервое, что заметил: залипла кнопка. Дамир М снял деталь, показал износ, вопросов не осталось. Техсервис в Алматы, если что, вот их адрес — не пожалел. Починили и дали гарантию на месяц
Павел Ш.Order No. 937748 · 9 December 2018
oursПрочитал кучу отзывов, половина — реклама, но тут вроде живые. Основная жалоба — не заряжается. Отдельно спасибо мастеру — Дамир М, терпения ему хватило. Проверил дома — всё на месте, ничего не забыли.
Марат Ж.Order No. ZK-4347 · 4 July 2018
oursКүтуге уақытым жоқ еді, сол күні алып кеттім. Бағасы базардағыдан қымбат емес. Енді басқа жерге бармаймын
Аружан К.Order No. ZK-2017/589 · 12 January 2017
oursДамир М честно сказал, что менять, а что ещё походит. Внешне как новый, если не считать мелкой царапины.
Didn’t find the answer? Message us on WhatsApp.
Ask a questionYes, we accept Nikon film cameras, including mechanical models with manual film advance. A technician will come to you, run free diagnostics, and identify the cause of the issue. Some components may have limited availability depending on the model.
A shutter error message points to a malfunction in the shutter mechanism or its drive, and the exact meaning depends on the camera model. A technician will determine the precise cause during free diagnostics. Taking the camera apart yourself often makes subsequent repairs more difficult.
Most often, jamming is caused by the zoom mechanism or autofocus drive, and these components can be repaired. Whether to replace the lens is decided after disassembly and diagnostics, and it depends on the lens model. The technician will explain the options and get your approval before proceeding.
After an impact, the lens mount, lens ribbon cable, or autofocus mechanism are most commonly affected, and sometimes optical elements shift. Diagnostics will show whether the camera body or the lens is damaged. Until it's inspected, avoid repeatedly trying to engage autofocus, as this can make the problem worse.
If defects appear in photos taken with different lenses, the sensor is likely the issue; if the image changes from lens to lens, the problem is in the optics. A technician will pinpoint the cause during free diagnostics, including checking test shots.
Sticking is often caused by dirt or wear in the zoom mechanism, and these components can be repaired. The decision to replace is made after disassembly and diagnostics, and it depends on the lens model. The technician will agree on the repair option with you.
Tech Service repairs Nikon cameras in Almaty: our technician comes to your home within 60 minutes or you can drop off the camera at the service center. Diagnostics is free, and there is a 1-year warranty on labor and parts. We fix DSLRs, Z-series, film models, and lenses, and we decode error codes during diagnostics.
Nikon cameras differ in design and lens mount, and that affects how we track down the cause of a fault. Here's which lines we work with and what we check first.
We service both Nikon DSLRs with the F-mount and Z-series mirrorless cameras, including lenses for both standards. In DSLRs the focus is on mechanics: the shutter fires tens of thousands of times, and the lens mount bears the weight of heavy optics, so wear builds up predictably. In Z-series mirrorless cameras there's less mechanics but more load on the electronics — the ribbon cables between the body and the display, the control board, the focus drive. In my experience, a DSLR more often comes in with a stuck shutter or a loose mount after a drop, while a Z camera comes in with intermittent faults that show up every other time. We start Nikon camera repair in Almaty by diagnosing the assembly that's under load in that particular design: on DSLRs we check the shutter and mount, on Z-series we check the electronics and ribbon cables, and from there we work toward the cause.
We also take in film Nikon cameras and Coolpix compacts, though film models require deeper disassembly of the mechanics. On such gear the critical parts are the film advance mechanism and light sealing: light leaks on some frames or a jerk during rewinding immediately point to wear in that assembly, not to the optics. Coolpix compacts have a different weak spot — the retractable lens that folds in every time you turn the camera on, and the power supply: the camera won't start or shuts down by itself on a worn battery. When you bring in such gear, give the exact model and describe the conditions where the fault appeared — in the cold, after a long idle period, when zooming. The more specific the details, the faster the technician finds the assembly: 'won't turn on' and 'won't turn on after a drop' lead diagnostics down different paths.
| What we service | What we check | When to come in |
|---|---|---|
| F-mount optics | contacts, aperture, lenses | won't focus, zoom sticks |
| Z-mount optics | ribbon cable, focus drive | camera doesn't see the lens |
| Speedlight flash | bulb, contacts, charging | doesn't fire or won't charge |
| Lens mount | mount, play | after a drop, lens wobbles |
Some complaints owners describe with a code on the display, others with words like 'won't turn on' or 'doesn't see the card'. Here's what's behind them and when you actually need a technician.
If a Nikon won't turn on, we first check the power and battery contacts, and for a 'doesn't see the card' complaint we check the memory card slot, and only then conclude there's a board fault. Oxidized contacts in the battery compartment, bent pins in the SD or CF connector, a torn ribbon cable between the board and the slot — these three causes account for a noticeable share of power and recording complaints. Nikon camera diagnostics are free with us, so the technician checks power and the slot before making any calls about replacing electronics. A shutter release button with a stuck contact and a battery drained to zero produce the same 'dead' camera picture as a failed board. Before bringing the camera in, it's worth trying a known-good card and a charged battery — some cases are resolved exactly that way, with no intervention.
An Err code and a shutter error message on a Nikon mean the camera couldn't complete a shooting cycle. We decode them during diagnostics by checking the shutter mechanism and drive. Behind the abbreviation on the display is a specific component: stuck blades, worn cocking drive, or misaligned curtain timing. Decoding the code without disassembly is a guess, not a diagnosis: the same Err on different models points to different mechanisms. The same code often appears due to a dead battery or a dusty lens mount, so the technician first rules out external causes. A shutter error doesn't always require replacing the unit—sometimes servicing the mechanism is enough. But a recurring code after a settings reset is a reason to stop shooting and avoid further mechanical damage.
After an impact, Nikon cameras most often suffer at the lens mount and focus drive; after water contact, it's the electronics and ribbon cables. We handle such cases first. A shifted lens mount causes lens play and autofocus misses, a crack on the board shows up as intermittent failures, and dried connectors cause oxidation that eats away contacts over weeks. Sand and fine dust packed into the focus ring after a drop on the ground are a separate story: they prevent the lens from moving to the stop and gradually wear down the drive gears. Tech Service restores Nikon cameras damaged by impact and moisture, and such work is covered by a 1-year warranty on labor and parts. Don't turn on a camera that's been in water to check it—applying power to a wet board often turns electronics restoration into parts replacement.
The same complaint "it won't focus" can come from either the lens or the camera. Here's how a couple of checks can narrow it down to a specific component before taking anything apart.
The fastest way to isolate the fault is to mount the lens on a known-good camera and shoot the same scene. Take a body that definitely shoots sharp, attach the suspect lens, and repeat the shot from the same distance with the same lighting. Watch the focus drive behavior, the aperture response, and any error codes on the display. If the lens works fine on the second camera but not on yours, the cause is in the body, lens mount contacts, oxidation, or play. The opposite is also telling: a consistent defect on both cameras points to the lens. Don't blame the sensor yet—the image sensor has its own symptoms, like identical spots on every shot. If your own checks don't clarify things, Nikon camera repair in Almaty is done by a technician after free diagnostics. Before going to the service center, check the lens mount for play and clean the contact groups—this rules out some false conclusions.
We usually restore a sticking zoom or aperture rather than replace the entire lens, as long as the glass and body are intact. In our practice, the main cause is worn focus drive, thickened lubricant on the guides, and sticking aperture blades—not broken lens elements. Lens alignment and mechanism servicing restore smooth movement and accurate focusing. Replacing the lens makes sense for chips or clouded glass, a cracked body, or a damaged ribbon cable that can't be replaced separately. A Tech Service technician disassembles the unit on-site and gives you the options based on free diagnostics. We provide a 1-year warranty on labor and parts—this covers both focus drive replacement and blade servicing.
We offer sensor and lens cleaning as a separate service when you notice recurring spots in your photos or a loss of sharpness. It's easy to tell the source apart: dust on the sensor leaves identical spots on every shot with any lens, while spots that move when you change lenses are dust on the glass, and that's what needs cleaning. Sensor dust is especially visible at small apertures when shooting a uniform background like sky or a wall. Cleaning the lens exterior won't solve the problem if particles are already under the front element or on internal surfaces. The technician assesses the contamination during inspection and only takes on the work where cleaning is truly needed, without unnecessary disassembly. After cleaning, we check the result with test shots and provide a 1-year warranty.
It's not always convenient to bring your camera to the service center, so here's what the specialist does on site, what they take with them, and how the work is agreed upon.
The technician arrives at your home within 60 minutes anywhere in the city and performs an initial check of the camera and lens on the spot. The first thing the on-site specialist does is inspect the lens mount for play, check the battery and power contacts, attach the lens, and listen to how the autofocus drive operates. Some faults are visible during inspection—oxidized contacts, a misaligned mount, no response to power—and such defects are fixed immediately. Components that require disassembly are taken to the service center by our technician to avoid dismantling the device in mid-air and losing screws. Before the visit, specify the complaint and model: we select the right tools based on your description and avoid wasting time on a second trip. Also mention what exactly you were shooting when the failure occurred—this fact often narrows down the suspect components even before inspection.
Diagnostics for a Nikon camera is free, and based on the results the specialist quotes the cost of work before service begins. The check includes inspecting the body and lens mount, testing the shutter at different speeds, reading error codes from the display, checking recording to an SD or CF card, and assessing the sensor condition. It's best to bring your memory card and battery—with them, the complaint is reproduced faster and the faulty component is identified more accurately, rather than testing the equipment blindly. If the device doesn't turn on, diagnostics start with power and contacts, not disassembly. The cost is quoted after the check—before you agree to any work. This approach saves money: sometimes the issue isn't in the camera body but in the card or lens, and there's no need to replace an expensive component.
If the fault requires disassembly, the camera is repaired at the service center and then tested with test shots before being returned. Our technician disassembles the unit, fixes the cause—replaces the shutter mechanism, cleans contacts, adjusts the lens mount—and reassembles the device. It's best to test with the same card and lens the owner brought in—that way you can see if the exact error you came with is gone. Test shooting at several shutter speeds and focus modes shows whether the equipment maintains exposure and writes files without errors. The 1-year warranty on labor and parts covers the performed service. Take the test shot results with you—at home, you can easily verify that the defect hasn't returned during normal shooting.
Choosing a technician isn't just about turnaround time. What matters is who is responsible for the work and what happens if the defect returns. Here are the conditions to look at before handing over your camera.
We provide a 1-year warranty on labor and parts, and it covers the replaced camera components. This includes the shutter, flex cables, connectors, and other parts that the technician installed instead of the failed ones. The condition applies both on-site and at the service center — the owner does not need to negotiate it separately during intake. The parts warranty is important separately from the labor warranty: if the replaced component itself fails, the owner won't have to prove that the cause is the part and not how the camera was handled. Therefore, when handing in the equipment, ask which components were included in the list of replaced ones — this simplifies the review of a repeat request, removes unnecessary disputes, and saves time for both parties.
Tech Service is a direct contractor: your camera is received and serviced by our own technician, not an intermediary who passes the equipment to a third party. Our specialists have been working with Nikon for 4 to 20 years, so they know the behavior of specific lines and typical combinations of faults. The on-site technician comes to the client anywhere in the city and performs diagnostics on the spot, and if disassembly is needed, the camera goes to the same specialist at the service center. With an intermediary, responsibility for the work is blurred between the receiver and the executor; with a direct contractor, there is one point of contact for both warranty and repeat requests. Ask before handing over the camera who exactly will disassemble it — the answer immediately shows who you are dealing with.
If after service the Nikon shows the same error again, we accept the camera under warranty and perform diagnostics again to find the true cause. A repeating code often indicates that the first approach addressed the symptom rather than the source, so the technician checks related components, not just the one that was replaced. In this case, diagnostics for the Nikon camera is free again: disassembly is not charged separately, even when the fault reappears. It's worth writing down or photographing the Nikon error codes before the visit — they make it easier to compare the camera's behavior before and after the work. After the check, we show which component failed and what actions were performed on it — so the owner sees the logic of the work, not just the final result.
Here are the key guidelines to help you make a balanced decision about restoring your Nikon camera and avoid wasting time on unnecessary procedures when contacting a technician.
12brands
Choose your brand to go to the repair page for your camera.
Tech Service technicians repair other appliances too — with the same 1-year warranty on labour and parts.
Refrigerator Repair in Almatyfrom 3 000 ₸
Washing Machine Repair in Almatyfrom 3 000 ₸
Dishwasher Repair in Almatyfrom 3 500 ₸
Oven Repair in Almatyfrom 3 000 ₸
Cooktop Repair in Almatyfrom 3 500 ₸
Air Conditioner Repair in Almatyfrom 3 500 ₸
Boiler and Water Heater Repair in Almatyfrom 2 500 ₸
Freezer Repair in Almatyfrom 6 000 ₸
Tumble Dryer Repair in Almatyfrom 5 000 ₸
Coffee Machine Repair in Almatyfrom 2 500 ₸
Robot Vacuum Cleaner Repair in Almatyfrom 3 500 ₸
Vacuum Cleaner Repair in Almatyfrom 1 500 ₸
Microwave Oven Repair in Almatyfrom 2 000 ₸
Hair Dryer Repair in Almatyfrom 1 500 ₸
Iron Repair in Almatyfrom 3 000 ₸
Electric Kettle Repair in Almatyfrom 2 500 ₸
Mixer Repair in Almatyfrom 2 500 ₸
Multicooker Repair in Almatyfrom 500 ₸
If your laptop screen is broken, turn the device off first, don't press on the display, and check the picture through an external monitor.
12 March 2026 · 11 minutes read
If your laptop freezes, the first thing to do is restart it and check Task Manager to see what's loading the CPU and memory.
25 January 2026 · 12 minutes read
If your computer won't turn on, start simple: check the outlet, power cable, switch on the power supply, and the power button.
19 January 2026 · 13 minutes read
If your laptop won't boot, first determine which of two states you're in: the device doesn't respond to the power button at all…
13 December 2025 · 12 minutes read












