Вера Э.Order No. 2510-1079 · 17 September 2025
oursХотел вызвать на дом, но в ЖК не пускают без пропуска. С этим и пришёл: течёт. Полёт нормальный)
City
Language
What broke
Sections
Message on WhatsApp+7 (778) 746 00 26Mon–Fri 10:00–19:00, Sat–Sun 11:00–18:00
A technician arrives within 60 minutes anywhere in the city. Diagnostics are free.
Our own technicians4 to 20 years of experience




Repair prices
Below are typical symptoms and the most common cause. The technician will pinpoint the exact issue.
Clogged filter, refrigerant leak
from10 000 ₸
Clogged drain, misaligned unit
from6 500 ₸
No power, faulty board
from14 000 ₸
Worn fan, loose mounting
from13 500 ₸
Code points to a component: sensor, board
from8 500 ₸
Dirty filter, evaporator
from9 500 ₸
Four-way valve, heating element
from8 500 ₸
Overheating, compressor protection
from24 500 ₸
The table lists the 'from' price for labor, for common jobs also the 'from' price of the part, plus the time required to complete the job.
1–2 hourstime
from 10 000 ₸cost

BeforeAfter5 steps

From request to performance check — five steps.
Submit a request, the technician will agree on a convenient time and come over.
A technician arrives within 60 minutes anywhere in the city.
The technician records the inspection results and explains which component failed.
The scope and cost of work are agreed with you before repair begins.
Test run in different modes and handover to the owner.
We reply during working hours
Choose a convenient window for the technician's visit — they will confirm the time and come to diagnose the split system.

Warranty question? Call us
+7 (778) 746 00 266 127 reviews of repairs at TECH SERVICE in total
Вера Э.Order No. 2510-1079 · 17 September 2025
oursХотел вызвать на дом, но в ЖК не пускают без пропуска. С этим и пришёл: течёт. Полёт нормальный)
Валентина Р.Order No. AS-5172 · 22 December 2023
oursПервое, что заметил: не холодит. Дамир М принял без вопросов, хотя был без записи. Даже сосед заметил, что громче не стало.
Григорий И.Order No. AS-2376 · 12 October 2021
oursС левого берега ехать далеко, поэтому искал поближе к дому. Ходил вокруг него три дня, потом плюнул и повёз. Больше всего мешало: ошибка. Шум ушёл, работает мягко.
Валерия А.Order No. 50417 · 1 September 2020
oursРаньше обращался в другой сервис, там очередь на две недели. Ремонт мобильного кондиционера заказывал впервые. Первое, что заметил: не холодит. Дамир М посмотрел и честно сказал: менять не надо. Итог — 36 000 тенге, ничего сверху. Замена: компрессор. Сейчас пашет без нареканий.
Альмира П.Order No. AS-3646 · 12 January 2020
oursӘйелім «таста» деді, мен көрсетуді жөн көрдім. Мастер бәрін түсіндірді. Ақауын тез анықтады, қажетсіз нәрсе ұсынбады. Жұмысты сол күні аяқтады. Ескі бөлшекті көрсетіп, қайтарып берді. Қайта жүгінуден тартынбаймын)
Олег Х.Order No. 55752 · 30 December 2018
oursДруг из Сарыарки посоветовал это место. Заявку оставил на всякий случай, а зря время тянул. Проблема ровно одна: течёт. Сначала думал, что нужен паспорт, но обошлось. Гудит ровно, не перегревается.
Вера Э.Order No. AS-4851 · 15 September 2018
oursДруг из Сарыарки посоветовал это место. Настроение было — хуже некуда. Основная жалоба — не холодит один блок. Дамир М отсоветовал дорогой ремонт, предложил простой. Сравнивал — здесь дешевле. Вскрытие показало: компрессор. Приняли вечером, хотя до закрытия оставалось минут десять. Ни шума, ни запаха, всё штатно!!
Салтанат К.Order No. AS-5029 · 21 December 2017
oursҚыс қатты, техникасыз қиын, сондықтан тез жөндеу керек болды. Таңертең қоңырау шалдым, түске дейін апардым. Жұмысты сол күні аяқтады. Ескі бөлшекті көрсетіп, қайтарып берді. Диагностика тегін болды. Барлығы ресми, чек берді. Түскі үзіліске қарамастан қабылдады. Мастер бәрін түсіндірді. Қайта жүгінуден тартынбаймын.
Фариза Л.Order No. TSA-39229 · 31 October 2017
oursҚұрылғы ескі, бірақ жақсы қарайды екен. Екі күнен кейін өзі қоңырау шалды. Келесіде де осында келемін.
Фёдор Б.Order No. AS-8520 · 21 August 2016
oursДамир М посмотрел и честно сказал: менять не надо. Приняли, объяснили, что и почему, без спешки. Функционирует, тьфу-тьфу
experience10 yearsAir conditioner refill technician
experience2 yearsAir conditioner cleaning technician
experience14 yearsAir conditioner chemical cleaning specialist
experience15 yearsMobile air conditioner technician
experience15 yearsLead HVAC specialist
Didn’t find the answer? Message us on WhatsApp.
Ask a questionMidea air conditioners most often have issues with the control board, compressor, and temperature sensors. Inverter models are sensitive to voltage spikes, so the electronics act up. It depends on the model and operating conditions.
Midea inverter models with heating and air purification are a good fit for home use. They are quieter and more efficient than standard ones. The choice depends on the area and budget.
A Midea inverter is more efficient and quieter, but repairs are more complex due to the electronics. A standard air conditioner is easier to service and cheaper to repair. The choice depends on your priorities.
If your Midea is blowing warm air, it's likely a refrigerant leak, a compressor fault, or clogged filters. The technician will pinpoint the cause after free diagnostics.
A direct contractor names their company and provides a warranty on labor and parts. They don't redirect you to another technician. In Astana, Tech Service is a direct contractor—our technician comes personally.
A Midea inverter can be repaired: the board, compressor, or sensors are replaced. Replacement is needed if the unit can't be repaired. The technician will suggest a solution after diagnostics.

Author: Erlan Zh.,Air conditioner refill technician
Published
Updated
Tech Service repairs Midea air conditioners in Astana with its own technician: he comes to your home or takes the unit to the service center. Diagnostics are free, arrival within 60 minutes anywhere in the city, and a 1-year warranty on labor and parts. The technician gives you the price after diagnostics, and you can pay via Kaspi QR, Kaspi Red, bank card, cash, or bank transfer for companies.
These are the three most common symptoms Midea owners call a technician about: weak cooling, water dripping from the indoor unit, and failure to start. Each has its own cause — from a simple clog to a compressor failure.
Most often, a Midea AC doesn't cool because of a refrigerant leak, a clogged filter, or a dirty heat exchanger; less often, it's a compressor or sensor failure. A leak in the refrigerant line gradually reduces cooling capacity: the split system first blows cool air, then barely cool, and in cooling mode it blows warm air. Clogged coarse filters block airflow, and the evaporator freezes up even though the compressor is fine. A dirty outdoor unit heat exchanger prevents heat dissipation, and the unit loses capacity even with a full charge. Failed temperature sensors give incorrect readings, and the electronics stop the compressor prematurely. If the outdoor unit is running but the air is warm, don't run the AC for hours — with a refrigerant leak, the compressor runs without lubrication and wears out faster.
A leak from the indoor unit of a Midea AC usually means a clogged drain system or a displaced drain hose, not a failure of the refrigeration circuit. Condensate collects in the drain pan and should flow out by gravity or via a pump; when the tube gets clogged with dust and slime, water overflows the pan and drips into the room. A displaced or disconnected hose causes the same picture — moisture goes past the drain. Less often, the cause is a drain pump that stops pumping water, or evaporator freezing, which makes condensate flow more actively than usual. If water appears only in high humidity and after long operation, check the indoor unit's tilt — even a slight misalignment leads to condensate overflowing the pan.
If your Midea AC won't turn on, the cause is usually in the electrical circuit, start component, or control board; a humming compressor that won't start points to a start problem or the compressor itself. No response to the remote often relates to power: check the breaker, outlet, and wiring integrity to the unit. The control board stops sending commands after a voltage spike or moisture ingress, and the unit stays silent even with good power. Humming without starting is a sign of a seized compressor or a failed start component that prevents the rotor from spinning up. The compressor compresses refrigerant in the circuit, and with a start problem, pressure doesn't build and no cooling occurs. Don't try to "kick-start" a humming compressor by repeated on/off cycles — that burns the winding, and instead of replacing the start component, you'll need to replace the whole assembly.
A signal on the Midea display is a hint, not a verdict: it points to the component that needs checking and helps the technician arrive prepared.
A Midea error code is an alphanumeric signal from the control board indicating that a sensor or component is out of range, not a description of a specific broken part. The controller continuously processes signals from temperature sensors — inlet air, outlet air, and heat exchanger — and compares the readings against the acceptable range. When a sensor's resistance goes out of bounds or data exchange with the outdoor unit is interrupted, the electronics log the event and display a character combination on the indoor unit's display; on some series, an indicator blinks in a specific pattern instead of showing digits. The set of characters depends on the lineup: household split systems usually show a Latin letter with a digit, while semi-industrial models may have two-digit combinations. Note the code and when it appeared — at startup, in hot weather, after defrost — this pair tells the technician more than the symbols alone and saves diagnostic time.
| Code group | What it indicates | What we check |
|---|---|---|
| Temperature sensors | Open or short circuit in the air or heat exchanger sensor | Sensor resistance, connector |
| Unit communication | No data exchange between indoor and outdoor units | Cable, boards of both units |
| Compressor protection | Overheating, overcurrent | Current, start component, compressor |
| Fans | Motor stop or failure | Motor, impeller, power supply |
Inverter Midea units are more complex than conventional splits: the electronics control the speed of the power unit, so precise diagnostics of the specific component matter more than replacing parts "just in case."
Yes, inverter Midea units are repairable: we identify the faulty component — inverter module, sensor, or power unit — and restore just that part without replacing the entire system. The inverter module controls the motor by smoothly varying its speed, while temperature sensors provide signals about the current mode. More often, the module itself or its circuitry fails, less often the windings. Our diagnostics are free, a technician arrives within 60 minutes in the city, and there is a 1-year warranty on labor and parts. After winter, an inverter Midea often fails to start not because the module is "dead" but due to moisture and oxidized contacts — so we start by checking the circuits, not by replacing an expensive component.
We first diagnose the Midea control board: some faults — a broken trace, a bulging capacitor, an oxidized connector — can be fixed by repair, and the module is replaced only in case of serious damage. The board processes temperature sensor signals and controls the indoor unit's fan, so its failure is rarely isolated. Board restoration is included in the service call: diagnostics are free, and there is a 1-year warranty on labor and parts. The board is often only indirectly "to blame": if its output stage has burned out, the cause may be a short circuit in the fan motor — without fixing the cause, a new board will fail the same way. In practice, we first test the fan winding and only then proceed to solder the output stage — so the module replacement isn't repeated twice.
When a Midea unit hums without starting, the cause is usually the start component, capacitor, or the winding of the power unit. We check the circuit step by step before recommending replacement of the assembly. The motor compresses refrigerant in the circuit, and its failure can't be determined by sound alone—you need winding resistance measurements and a check of the start component. We perform this Midea air conditioner compressor repair in Astana on-site: arrival within 60 minutes, free diagnostics, 1-year warranty. If the unit starts and then shuts off on protection after a few minutes, the problem may not be the compressor itself but overheating due to a dirty outdoor coil. In our experience, such protection is more often resolved by cleaning the coil and checking circuit pressure than by intervening in the motor itself.
Our Midea service starts with free on-site diagnostics, after which the technician provides a quote and gets your approval for the work. Here's what happens at each stage.
We come to diagnose your Midea unit for free: the technician checks electrical circuits, sensors, circuit pressure, and operating modes, then provides a quote for the work. Citywide arrival takes up to 60 minutes—the technician brings their own tools and starts the inspection right away. The check covers the entire chain: from the power supply and board to the compressor and refrigerant circuit. First, they measure the mains voltage and check the integrity of electrical circuits, then take readings from temperature and pressure sensors and assess how the inverter behaves during startup. Based on the inspection, you get a clear explanation: what exactly failed, what work is needed, and how much it will cost. On-site diagnostics identifies most faults without removal—taking the unit to the shop is only necessary for complex board or compressor repairs.
We don't recharge refrigerant by guesswork: first we locate the leak in the line and connections, fix it, and only then recharge the Midea unit with refrigerant. The technician inspects the refrigerant line along its entire length, checks the flare connections on the indoor and outdoor units, pressure-tests the circuit with nitrogen, and listens for hissing along the line. The found soldering point on the copper lines is heated with a torch, solder is applied, and the joint is pressure-tested again for tightness. Only after the circuit holds pressure is the system evacuated and charged with refrigerant strictly by weight and type specified on the model's nameplate. If refrigerant leaks again within a season, the cause is usually a loose connection or a microcrack—without soldering and pressure testing, a simple top-up only postpones the problem.
In the capital's market, direct contractors and aggregators work side by side, and the difference shows in who actually comes to you and who stands behind the result after the work.
Tech Service is the direct contractor: our own technician comes to you, not a subcontractor from an aggregator, so we stand behind both the work and the parts. Our in-house specialist knows the Midea lineup by model: they can tell inverter units from standard ones, read the codes on the display, and select parts for the specific component. With an intermediary, a dispatcher takes the request and a third-party specialist you didn't choose shows up at your address. Ask in advance who will actually perform the service and who will honor the warranty: with an intermediary, a third party assumes the obligations, and if the problem recurs, you have to deal with them. In my view, the question "who will come" should be asked before the visit, not after the unit has been taken apart.
We provide a 1-year warranty on labor and a 1-year warranty on parts, and the technician quotes the price after free diagnostics, before any work begins. Diagnostics are free and done at your home: the specialist checks the pressure in the circuit, the compressor current, and the condition of the control board, then explains which component has failed and what options you have. A technician arrives within 60 minutes anywhere in the city, and payment is accepted in any convenient way. The parts warranty matters separately from the labor warranty: if a part fails before its time, it is replaced rather than blamed on operating conditions. So in a warranty case, you return to the same contractor instead of looking for a new one.
If your Midea equipment is still under the manufacturer's warranty, it's best to contact them first under the warranty terms, as going to a third-party service may affect those terms. The manufacturer usually requires that any intervention be performed according to its regulations—signs of third-party intervention, a broken seal on a component, or replacement with a non-original part can give grounds to revise the obligations. A common cause of early failures is improper installation: a short pipe run, skipping vacuuming, or weak mounting of the outdoor unit. In Astana's climate, the air conditioner faces a higher load due to frost and heating mode, so pre-season maintenance reduces the risk of breakdowns after winter. Check the warranty period on your purchase document before calling a technician—this way you won't lose the right to free repair of a manufacturing defect and won't pay twice.
Five short takeaways to help you find the cause of an air conditioner breakdown faster and avoid paying for unnecessary work. Here's what to keep in mind before the technician arrives.
80brands
We work with air conditioners and split systems of every brand sold in Kazakhstan — from Almacom, Gree and Midea to LG, Samsung, Chigo and rare imported makes. Can’t find yours in the list? Call anyway — a technician will come and take a look.
Tech Service technicians repair other appliances too — with the same 1-year warranty on labour and parts.
Refrigerator Repair in Almatyfrom 3 000 ₸
Washing Machine Repair in Almatyfrom 3 000 ₸
Dishwasher Repair in Almatyfrom 3 500 ₸
Oven Repair in Almatyfrom 3 000 ₸
Cooktop Repair in Almatyfrom 3 500 ₸
Air Conditioner Repair in Almatyfrom 3 500 ₸
Boiler and Water Heater Repair in Almatyfrom 2 500 ₸
Freezer Repair in Almatyfrom 6 000 ₸
Tumble Dryer Repair in Almatyfrom 5 000 ₸
Coffee Machine Repair in Almatyfrom 2 500 ₸
Robot Vacuum Cleaner Repair in Almatyfrom 3 500 ₸
Vacuum Cleaner Repair in Almatyfrom 1 500 ₸
Microwave Oven Repair in Almatyfrom 2 000 ₸
Hair Dryer Repair in Almatyfrom 1 500 ₸
Iron Repair in Almatyfrom 3 000 ₸
Electric Kettle Repair in Almatyfrom 2 500 ₸
Mixer Repair in Almatyfrom 2 500 ₸
Multicooker Repair in Almatyfrom 500 ₸
Air conditioner errors are codes on the display or flashing indicators that show which component has failed.
5 March 2026 · 12 minutes read
If your air conditioner is leaking, first turn it off and cut the power, place a container under the drip, and move any wiring away from the water.
19 October 2025 · 12 minutes read
Gas boiler errors are codes on the display or a flashing indicator that point to a specific component: ignition, pressure, draft, sensor, or control board.
10 February 2026 · 11 minutes read












