Мария Р.Order No. 58534 · 26 June 2025
oursDamir M sam pozvonil i skazal, chto gotovo. Funktsioniruet, tfu-tfu. Полёт нормальный.
City
Language
What broke
Sections
Message on WhatsApp+7 (778) 096 59 61Mon–Fri 10:00–19:00, Sat–Sun 11:00–18:00
We come to diagnose and repair LG microwaves. 1-year warranty on labor and parts.
Our own technicians4 to 20 years of experience




Repair prices
Below are typical symptoms and the parts we check first.
magnetron, diode, capacitor
from4 500 ₸
mica plate, carbon buildup, coating
from3 000 ₸
fuse, switch, board
from4 000 ₸
fan, transformer, magnetron
from5 000 ₸
latch, door hook, spring
from5 500 ₸
code points to the part to check
from8 500 ₸
drive motor, coupling, rollers
from4 500 ₸
high-voltage diode, capacitor
from4 500 ₸
The table shows microwave repair prices for LG in Astana: a starting labor cost without parts and the timeframe. The technician confirms the final total before any repair work begins.
1–2 hourstime
from 7 500 ₸cost

BeforeAfter5 steps

From request to check — five steps, free diagnostics.
Leave a request, describe the symptom and model — the technician will prepare for the visit.
The technician comes anywhere in the city, inspects the appliance and its location.
The technician agrees on the scope of work and the list of parts to replace.
Replacing parts and adjusting components, checking the microwave's operation.
You turn on the oven and check heating and all modes together with the technician.
We reply during working hours
Leave a request — the technician will arrive within 60 minutes. Diagnostics are free, 1-year warranty on labor and parts. Specify the model and symptom.

Warranty question? Call us
+7 (778) 096 59 616 127 reviews of repairs at TECH SERVICE in total
Мария Р.Order No. 58534 · 26 June 2025
oursDamir M sam pozvonil i skazal, chto gotovo. Funktsioniruet, tfu-tfu. Полёт нормальный.
Эвелина Ш.Order No. AS-6327 · 20 December 2024
oursВыбирал между официальным и этим, выбрал этот. Жалоба одна: искрит. Гудит ровно, не перегревается.
Георгий З.Order No. AS-4788 · 16 May 2024
oursЗаявку оставил через сайт вечером, утром перезвонили. Вчера работало, сегодня уже не крутиться тарелка. Про тех сервис слышал на Сарыарке. Функционирует, тьфу-тьфу.
Анастасия Т.Order No. AS-9829 · 4 August 2023
oursПричина обращения — не крутится тарелка. Радик Т всё сделал при мне, за пятнадцать минут. Полёт нормальный.
Екатерина К.Order No. TSA-91571 · 2 May 2023
oursСмотрел, чтобы был свой склад запчастей, а не под заказ. Жалоба одна: не греет. После ремонта — как новое
Степан Я.Order No. AST-2103-257 · 2 April 2021
oursЗимой без техники никак, поэтому тянуть было нельзя. Больше всего мешало: не крутится тарелка. Нагрев в норме, посторонних звуков нет.
Наталия С.Order No. 2007-9661 · 27 October 2020
oursСмотрел, чтобы был свой склад запчастей, а не под заказ. Разозлился, конеш. Вещь не старая. С этим и пришёл: не крутится тарелка. Дамир М разобрался в редкой модели. Приняли вечером, хотя до закрытия оставалось минут десять. По факту меняли: двигатель. Нагрев в норме, постороних звуков нет.
Михаил У.Order No. 91281 · 25 May 2019
oursПереезжали в новую квартиру, техника после перевозки захандрила. Нужен был ремонт микроволновой печи. Больше всего мешало: не греет. Сейчас пашет без нареканий.
Леонид П.Order No. AS-8343 · 15 January 2019
oursЖиву в Есиле, искал сервис, чтобы не тащиться через весь город. Расстроился сильнее, чем следовало. Жалоба одна: искрит. Дамир М — мастер от бога, если можно так сказать. На ресепшене оформили за пару минут, выдали квитанцию. Ни копейки больше обещанного. Третий месяц — никаких проблем.
Вера Э.Order No. AS-2318 · 4 April 2018
oursЗаявку оставил через сайт вечером, утром перезвонили. Открыл — и сразу понял: не греет. Всё быстро, но без суеты. Итог — 27 500 тенге, ничего сверху. Ни разу не пожалел)
experience14 yearsSenior small appliance technician
experience15 yearsOn-site coffee machine diagnostics technician
experience5 yearsCoffee machine cleaning technician
experience12 yearsCoffee machine diagnostics technician
experience5 yearsPortafilter coffee machine technician
experience12 yearsVacuum cleaner repair technician
experience15 yearsVacuum cleaner repair technician
experience18 yearsWashing machine repair technician
Didn’t find the answer? Message us on WhatsApp.
Ask a questionIf the microwave turns on but doesn't heat and the fuse is intact, the high-voltage diode is often the culprit. A technician can pinpoint the issue, and replacing the diode usually solves the problem. It depends on the model.
The control board of an LG microwave is more often repaired: the technician replaces burned-out components or restores the traces. If the damage is severe, the board is replaced with a new one. The decision is made after diagnostics.
Increased humming with no heating often indicates a faulty high-voltage transformer or magnetron. A failed capacitor is also possible. The technician will determine the exact cause after inspection.
Yes, using a sparking LG microwave is dangerous: it can cause a fire or damage the electronics. Unplug it immediately and call a technician. The cause is often the mica plate or a dirty cavity.
Repair will extend its service life if the body and cavity are intact and the breakdown is typical (magnetron, diode, board). With serious damage, a new appliance may be more cost-effective. The technician will give a recommendation after diagnostics.
The technician brings their own parts for LG, but the final choice depends on the model and the nature of the breakdown. If necessary, they will agree on a replacement option with you. Diagnostics are free, and there is a 1-year warranty on labor and parts.
Tech Service repairs LG microwaves in Astana: a technician comes to your home within 60 minutes anywhere in the city, or the work is done at our service center. Diagnostics are free, the technician gives you the price after diagnostics, and there's a 1-year warranty on labor and parts. Our technicians have 4 to 20 years of experience.
"Won't heat" is the most common reason to call a microwave technician for an LG. This symptom points to four different components, and the repair depends on which one failed.
Heating in an LG microwave is provided by a combination of four components — the magnetron, high-voltage transformer, high-voltage diode, and high-voltage capacitor — and "won't heat" means one of them has failed. The magnetron generates microwaves, the transformer steps up the mains voltage to operating kilovolts, and the diode and capacitor form a high-voltage pulse from it. Failure of any link breaks the chain, and the chamber stays cold even with a working fan and light. It's also worth remembering the high-voltage fuse: it takes the hit first during a breakdown and blows, protecting the other parts. The magnetron is replaced with a new one, while the diode and capacitor can often be replaced separately — that's why the technician checks the whole chain first instead of replacing the most expensive component at random.
During free diagnostics, our technician checks the entire high-voltage chain one by one — from the fuse and transformer to the magnetron — so the cause of "won't heat" is determined precisely, not by symptoms. First the high-voltage fuse is tested for continuity, then the transformer winding is measured, the diode and capacitor are checked, and only after that the magnetron itself is tested for breakdown and filament. A loud hum without heating usually points to the diode or transformer, while quiet operation without heating points to the magnetron; this is a guide for the customer, but the final conclusion comes from diagnostics. Our technicians have 4 to 20 years of experience, and they know all modifications of high-voltage blocks in LG microwaves, including inverter circuits where an inverter board replaces the transformer.
If the turntable doesn't rotate but heating works, the cause is usually the turntable motor-reducer, not the magnetron. The motor-reducer transfers rotation to the glass tray through a coupling, and when it stops, food heats unevenly — edges overheat while the center stays cold. Heating still works, so owners mistakenly link both symptoms to one failure. The combination "won't heat and won't spin" almost always means two independent faults, and the technician checks them separately — so the job doesn't turn into replacing everything. We advise not to ignore a single symptom: a stopped tray eventually breaks the coupling and the plastic reducer shaft, and the part has to be replaced along with the mount. The rollers and tray ring also wear out — they're inspected together with the reducer.
The LG microwave display shows a code when the electronics detect a deviation in a component's operation. The combination narrows the search but doesn't replace diagnostics.
An error code on the LG display points to a specific component that the control board considers faulty — most often it's the magnetron circuit, a sensor, or the touch panel. The alphanumeric combination consists of two parts: the first indicates the group — power, heating, communication with the panel, and the second specifies which signal went out of range. The electronics compare sensor readings with reference values and, if there's a discrepancy, block startup to avoid applying high voltage to a faulty circuit. Some codes are tied to the chamber temperature and fan operation: magnetron overheating and fan failure produce different codes, even though the oven behaves the same externally — it hums and doesn't heat. The electronics also pick up indirect signs: timer malfunction, door lock circuit failure, loss of signal from the buttons. The same code sometimes appears due to a simple power surge, so before calling a technician, it's worth completely unplugging the microwave for a few minutes. If the combination returns after powering on, diagnostics are needed.
If the code on the LG display doesn't reset after powering off, our technician during free diagnostics checks the electronic board and sensors — often the cause is the board itself, not the component indicated by the code. The board controls modes and the timer: it receives signals from the touch panel, turns on the magnetron and fan, and monitors temperature. When contacts oxidize or the panel ribbon cable is damaged, the command doesn't reach the component, and the electronics interpret this as a failure. The LG control board isn't always replaced entirely: some faults are related to contacts and ribbon cables of the touch panel, and fixing them is simpler than replacing the board. Our experience from 4 to 20 years allows us to distinguish a false signal from a real component failure — this is the basis for accurate diagnostics. A technician arrives at your home within 60 minutes anywhere in the city, and we provide a 1-year warranty on labor and parts.
Sparking and smoke are not a case where you should "wait and see what happens." Inside an LG microwave, high voltage and radiation are present, so it's best to show the fault to a technician immediately.
Sparking inside an LG microwave is most often caused by a damaged door seal, a dirty waveguide, or a faulty high-voltage component. The door seal keeps radiation inside the chamber, and its wear, tears, or loss of elasticity allow microwaves to escape. The waveguide, through which energy travels from the magnetron to the chamber, becomes coated with carbon and grease over time — breakdowns occur on it, causing flashes near the right wall. High-voltage components (diode, capacitor, transformer) when broken down produce a characteristic crackling and sparks near the waveguide. Another cause is damaged chamber coating: a chip in the enamel on the metal acts as a field concentrator. Metal dishes and foil cause sparks even in a working oven — if sparking continues after removing them, the problem is in the microwave itself, and you should stop using it until inspected.
Using a sparking or smoking LG microwave is dangerous: a faulty component can damage neighboring parts and create a fire risk. A breakdown in the high-voltage section affects the transformer windings and the magnetron — the component that generates radiation and is the most expensive part of the oven. Carbon deposits on the waveguide grow with each use, increasing the damaged area and the depth of the breakdown. Smoke from burning grease or wire is a signal to immediately unplug the oven, not to try reheating dinner again. A metallic hum and the smell of burnt insulation indicate transformer overload. The sooner the oven is diagnosed, the more often it can be fixed by replacing just one component — delayed intervention usually expands the list of damaged parts.
If your LG microwave starts sparking again after a repair, we check it again under warranty — repeat sparking usually means the cause wasn't the part we replaced but the door seal or the waveguide. Tech Service gives a 1-year warranty on labor and parts, so the follow-up inspection and fix come with no extra conditions for the owner. On a return visit, our technician checks not only the electrics but also the condition of the cavity and door: hairline cracks in the seal and carbon buildup on the waveguide cause the same flashes as a blown diode. In our experience, these two areas are the ones most often missed on the first visit. That's why during diagnostics we inspect the cavity and door alongside the electrics — it lowers the risk of a second callout.
We've set up LG microwave repair in Astana so the owner doesn't have to haul the appliance anywhere. The technician comes to your home, or the work is done at our service center — your choice.
We service LG microwaves both at your home and at our service center: a mobile technician arrives within 60 minutes anywhere in the city, and if the fault needs bench conditions, the unit is serviced at the center. On a home visit, the technician works with his own tools and checks the device on the spot — from the start circuit to the high-voltage assembly — without leaving the disassembly to the owner. We choose the in-shop format when the job needs a full teardown of the casing, soldering of the control board, or replacement of a unit that can't be done neatly in a kitchen without risking damage to nearby parts. For the owner, this means one thing: no need to find a car, box up the oven, drive it across town, and then pick it up again. In our experience, most faults — heating, turntable, controls — are fixed right on site, so transport is rarely needed. A separate note on models with a built-in hood and a complex panel: these are often easier to inspect at the service center, where there's a level surface and access to the connectors from all sides.
| What we check | Which symptom | What we do |
|---|---|---|
| Fuse and door lock | won't turn on | check the start circuit |
| Control board and panel | error code, unresponsive | diagnose the controls |
| High-voltage chain | not heating, humming | check magnetron, diode, capacitor |
| Turntable motor | turntable not spinning | check rotation |
| Door seal and cavity | sparking | inspect door and waveguide |
Warranty and payment are what clients ask about before booking a technician. Here we also look at when repairing an older LG microwave makes sense and when it's worth considering a new one.
We give a 1-year warranty on labor and parts, including a replaced magnetron — the same term applies to both the work and the installed part. The magnetron remains the most expensive component in an LG microwave, and owners most often ask about it: after replacing the emitter, the warranty slip is issued for the same period — 1 year, with no separate "short" term for the part. Replacing the diode, capacitor, turntable motor, or control board falls under the same conditions. The warranty covers both on-site service and work done at the service center, so where you get the repair doesn't affect the terms. In our practice, warranty claims for the magnetron are more often related not to the part itself but to an associated component that wasn't checked during the first installation — that's why when replacing the emitter, we check the entire power circuit.
Restoring an old LG microwave makes sense if a single component is faulty — the magnetron, diode, or motor — while the body, cavity, and controls are in good shape. The repairability of an old microwave depends on the condition of the cavity and the door seal: with intact enamel and an uncracked seal, replacing one element gets the appliance back in service for years. The expensive components — the magnetron and transformer — are separate in the design, and failure of one doesn't necessarily mean the other is bad. It's a different story when several expensive components are damaged at once or the cavity and seal are worn out: then the work loses its point. The technician says so directly after diagnostics rather than pushing services. In my view, an honest refusal to restore saves the owner more than a discount on an unnecessary replacement.
Diagnostics are free with us, and you can pay with Kaspi QR, Kaspi Red, card, cash, or bank transfer — the client pays only for the work and parts already agreed upon. The technician gives the price after free diagnostics, once the cause of the fault is identified: before that, quoting a sum would be guesswork. A technician's visit within the city takes up to 60 minutes, and diagnostics at your home is included in that visit. Free diagnostics benefit both the client and us: if the work isn't advisable, the owner learns about it at no cost, and we don't waste time on a job that makes no sense. We accept cash, cards, and transfers — the client chooses the method. Payment via Kaspi QR, Kaspi Red, card, cash, or bank transfer removes a question people often ask in advance: you can pay however is convenient.
Let's bring together what helps you decide about repairing your oven: what the cause of the breakdown depends on, when you shouldn't delay, and what terms to check before calling a technician.
40brands
We repair microwaves from popular brands. LG is one of the brands our technicians work with most often.
Tech Service technicians repair other appliances too — with the same 1-year warranty on labour and parts.
Refrigerator Repair in Almatyfrom 3 000 ₸
Washing Machine Repair in Almatyfrom 3 000 ₸
Dishwasher Repair in Almatyfrom 3 500 ₸
Oven Repair in Almatyfrom 3 000 ₸
Cooktop Repair in Almatyfrom 3 500 ₸
Air Conditioner Repair in Almatyfrom 3 500 ₸
Boiler and Water Heater Repair in Almatyfrom 2 500 ₸
Freezer Repair in Almatyfrom 6 000 ₸
Tumble Dryer Repair in Almatyfrom 5 000 ₸
Coffee Machine Repair in Almatyfrom 2 500 ₸
Robot Vacuum Cleaner Repair in Almatyfrom 3 500 ₸
Vacuum Cleaner Repair in Almatyfrom 1 500 ₸
Microwave Oven Repair in Almatyfrom 2 000 ₸
Hair Dryer Repair in Almatyfrom 1 500 ₸
Iron Repair in Almatyfrom 3 000 ₸
Electric Kettle Repair in Almatyfrom 2 500 ₸
Mixer Repair in Almatyfrom 2 500 ₸
Multicooker Repair in Almatyfrom 500 ₸












