Мария Р.Order No. 58534 · 26 June 2025
oursDamir M sam pozvonil i skazal, chto gotovo. Funktsioniruet, tfu-tfu. Полёт нормальный.
City
Language
What broke
Sections
Message on WhatsApp+7 (778) 096 59 61Mon–Fri 10:00–19:00, Sat–Sun 11:00–18:00
Technician arrives within 60 minutes anywhere in the city. Free diagnostics.
Our own technicians4 to 20 years of experience




Repair prices
Below are typical symptoms and likely causes. The technician will pinpoint the exact cause after diagnostics.
magnetron, diode, capacitor
from4 500 ₸
waveguide, mica, coating
from3 000 ₸
fuse, switch
from4 000 ₸
fan, transformer, magnetron
from5 000 ₸
motor, rollers, coupling
from4 500 ₸
hinges, latches, switches
from5 500 ₸
the code points to a specific component
from8 500 ₸
fan, mounting, transformer
from5 000 ₸
The table shows Gorenje microwave repair costs: a "from" labor price excluding parts and the turnaround time; the technician confirms the total before any work begins.
1–2 hourstime
from 7 500 ₸cost

BeforeAfter5 steps

Five steps from your request to checking the appliance after repair.
Describe the model and the symptom. The technician will agree on a convenient visit time.
The technician arrives within 60 minutes anywhere in the city, with tools.
The technician inspects the appliance on site and agrees on the next steps with you.
Have the model and a description of the symptom ready for the technician.
Agree with the technician on the time and method of handover after checking.
We reply during working hours
Ask the technician about a convenient visit time and how the appliance will be handed over for repair. The specialist will tell you how to prepare the microwave for inspection.

Warranty question? Call us
+7 (778) 096 59 616 127 reviews of repairs at TECH SERVICE in total
Мария Р.Order No. 58534 · 26 June 2025
oursDamir M sam pozvonil i skazal, chto gotovo. Funktsioniruet, tfu-tfu. Полёт нормальный.
Эвелина Ш.Order No. AS-6327 · 20 December 2024
oursВыбирал между официальным и этим, выбрал этот. Жалоба одна: искрит. Гудит ровно, не перегревается.
Юрий М.Order No. ZK-2024-559 · 10 July 2024
oursОфис на Кабанбай батыра, технику туда и повёз. С этим и пришёл: не крутится тарелка. Дамир М — мастер от бога, если можно так сказать. Ни разу не пожалел
Георгий З.Order No. AS-4788 · 16 May 2024
oursЗаявку оставил через сайт вечером, утром перезвонили. Вчера работало, сегодня уже не крутиться тарелка. Про тех сервис слышал на Сарыарке. Функционирует, тьфу-тьфу.
Эвелина Ш.Order No. TSA-53722 · 10 February 2024
oursДамир М провозился, но сделал. Приняли, объяснили, что и почему, без спешки. Проверил на всех режимах — держит!!
Анастасия Т.Order No. AS-9829 · 4 August 2023
oursПричина обращения — не крутится тарелка. Радик Т всё сделал при мне, за пятнадцать минут. Полёт нормальный.
Степан Я.Order No. AST-2103-257 · 2 April 2021
oursЗимой без техники никак, поэтому тянуть было нельзя. Больше всего мешало: не крутится тарелка. Нагрев в норме, посторонних звуков нет.
Наталия С.Order No. 2007-9661 · 27 October 2020
oursСмотрел, чтобы был свой склад запчастей, а не под заказ. Разозлился, конеш. Вещь не старая. С этим и пришёл: не крутится тарелка. Дамир М разобрался в редкой модели. Приняли вечером, хотя до закрытия оставалось минут десять. По факту меняли: двигатель. Нагрев в норме, постороних звуков нет.
Михаил У.Order No. 91281 · 25 May 2019
oursПереезжали в новую квартиру, техника после перевозки захандрила. Нужен был ремонт микроволновой печи. Больше всего мешало: не греет. Сейчас пашет без нареканий.
Леонид П.Order No. AS-8343 · 15 January 2019
oursЖиву в Есиле, искал сервис, чтобы не тащиться через весь город. Расстроился сильнее, чем следовало. Жалоба одна: искрит. Дамир М — мастер от бога, если можно так сказать. На ресепшене оформили за пару минут, выдали квитанцию. Ни копейки больше обещанного. Третий месяц — никаких проблем.
experience14 yearsSenior small appliance technician
experience15 yearsOn-site coffee machine diagnostics technician
experience5 yearsCoffee machine cleaning technician
experience12 yearsCoffee machine diagnostics technician
experience5 yearsPortafilter coffee machine technician
experience12 yearsVacuum cleaner repair technician
experience15 yearsVacuum cleaner repair technician
experience18 yearsWashing machine repair technician
Didn’t find the answer? Message us on WhatsApp.
Ask a questionYes, sparking can damage the oven and is dangerous for you, so unplug it right away. The cause is often dirt or a burnt mica plate, but you shouldn't skip a technician's inspection.
Yes, Gorenje inverter models are repairable, though diagnostics are more complex and depend on the model. A technician will assess the fault in the inverter board or magnetron and tell you what's more cost-effective — repair or replacement.
Yes, in most cases the panel can be repaired rather than replaced entirely. A technician checks the ribbon cable, contacts, and control board, and then tells you exactly what failed.
Unplug it immediately and don't turn it on again until it's been inspected. Smoke often comes from burnt wiring or dirt inside, and continuing to use such an oven is dangerous.
Usually it's not serious: the turntable motor or its coupling is often to blame, and the oven itself heats normally. A technician checks the assembly on-site and replaces the faulty part.
Yes, the 1-year warranty covers both the technician's work and the installed parts. The technician explains the exact terms when accepting the appliance after diagnostics.
Tech Service repairs Gorenje microwaves in Astana: our technician comes to your home or accepts the appliance at the service center. Diagnostics are free, call-out within 60 minutes across the city, 1-year warranty on labor and parts. The technician gives you the price after diagnostics, payment by any method.
Gorenje models tend to repeat the same symptoms, and one sign can already narrow down the faulty components. Let's go over the most common complaints that bring these units to a technician.
Most often we find the magnetron, high-voltage diode, or capacitor at fault — the microwave generation circuit fails while the motor and lamp stay working. The magnetron generates the microwave field for heating, powered by a high-voltage transformer paired with a capacitor and diode: a breakdown in any part of this chain leaves the unit turning on but cold. We check the entire chain in order — transformer windings, capacitor capacitance, diode breakdown, then the emitter itself. In my experience, the diode burns out most often, and the tube suffers next, so we replace them as a pair if the breakdown has affected both. If you hear a hum after turning it on but the food stays cold, don't run the oven empty — that finishes off the magnetron and makes diagnostics more expensive.
A stationary turntable in a Gorenje is usually the rotation motor or its coupling, while increased noise often comes from the fan motor or early magnetron wear. The turntable drive is a separate low-power motor under the cavity floor, and its coupling wears out over time: the plate stops while heating still works fine. Fan noise increases when grease builds up on the blades or the shaft bushing wears, and then the oven hums more steadily but noticeably louder. Tech Service replaces the turntable rotation motor and fan, and tests the generator tube separately on a bench. You can check the turntable by hand — if it spins freely but stays still during operation, the problem is in the drive, not the cookware.
A code on the display is not a verdict but a hint about which component to check first. Let's look at the most common combinations and what to do about them.
On Gorenje microwaves, the E4 code is most often linked to the heating sensor circuit or a fault in the electronic board, so the technician starts with the board and connectors, not the magnetron. The E3 combination in convection models points to the same measuring element, but through an open circuit or poor contact in the connectors. The E1 code indicates the door latch and interlock: the door doesn't close tightly, and the electronics won't start heating. The E2 combination on touch panels points to the board and ribbon cable. We provide free diagnostics before service to distinguish an electronics fault from high-voltage circuit wear. A message on the screen doesn't replace testing: the same error on different Gorenje models can point to different components, so it's worth checking the code against the manual for your specific oven.
| Code on display | What we check first | Common cause | Model type |
|---|---|---|---|
| E4 | heating sensor circuit, board | electronic unit failure | with electronics |
| E3 | heating sensor, connectors | open circuit or poor contact | with convection |
| E1 | door lock, interlock | door not closing tightly | all series |
| E2 | control board, ribbon cable | electronics failure | with touch panel |
| No code, not heating | magnetron, diode, capacitor | high-voltage unit wear | solo and grill |
Each Gorenje series has its own weak points and its own troubleshooting logic. Solo, grill, convection, and inverter models are disassembled and tested differently — let's bring the differences into one picture.
| Gorenje model type | What we check more often | Repair feature |
|---|---|---|
| Solo | magnetron, fuse, door lock | simple circuit, minimal electronics |
| With grill | grill heating element, control module | two heating circuits, separate grill check |
| With convection | convection fan, heater, electronics | more parts, longer diagnostics |
| Inverter | inverter circuit, magnetron | no high-voltage transformer |
| With touch panel | touch panel, ribbon cable, control module | controls are on the touch panel |
In Gorenje models with a touch panel, the panel itself, the ribbon cable, or the control module is usually to blame — we restore the panel or replace it rather than sending the oven to be replaced. In these models, the touch sensor is connected to the control electronics by a thin ribbon cable, and over time the contact in the connector weakens: the oven "sees" a press every other time or not at all. Our technician checks the ribbon cable, tests the sensor traces, and sees whether the signal reaches the control unit. If the traces are intact, we restore the sensor; if not, we replace the whole unit. Before taking the oven to the service center, wipe the panel dry: moisture and grease on the sensor sometimes cause a false "not responding," and this saves the technician a whole visit. Don't write off an inverter model — with a working magnetron, it's usually the inverter circuit that gets replaced.
Older Gorenje models are repairable if the magnetron and high-voltage circuit are working and the part is available; the decision is made after diagnostics, not based on the oven's age. The magnetron lasts a long time and is not a consumable, so many ovens with a long service life still have a working magnetron, and the failure is somewhere in the circuit or controls. Repairability hinges on something else—whether a suitable part exists for the specific series: for discontinued lines, some elements can be sourced from compatible series, and some cannot. The decision to restore should be based on the condition of the parts, not the year of manufacture: sometimes replacing one part extends the oven's life for years, while other times several components fail at once and the work no longer makes sense. Our diagnostics are free, so you can check the condition of the circuit even before you decide to change anything.
We work as a direct contractor, not an aggregator: our specialist comes to you, not a middleman. Here's what Gorenje microwave service in Astana looks like from request to inspection.
We service Gorenje both at home and in the service center: simple breakdowns are fixed on site, while complex ones involving the board or inverter are better handled in the service center. A freestanding Gorenje microwave is repaired right in the kitchen—access to the magnetron and high-voltage block is gained after removing the casing, and this doesn't require dismantling furniture. Built-in models with a control board are more often taken to the service center: soldering and tracing circuits require a bench and a calm table, not a windowsill next to the stove. Gorenje microwave repair in Astana at home is convenient for those who don't want to haul the appliance to a service center. In my experience, more than half of requests for this brand are resolved on the first visit—if the model and symptom are clarified in advance by phone. If the oven is built-in, the specialist will assess on site whether it can be removed without dismantling the kitchen—this affects the choice of service format.
We are a direct contractor: our specialists have 4 to 20 years of experience, so the person doing the work is responsible for it, not a middleman. With an aggregator scheme, the request goes to subcontractors, and the person who arrives may be seeing the specific model for the first time. Our on-site microwave technician works with this brand constantly: they know the layout of components in solo, grill, and inverter versions, so diagnostics doesn't turn into guesswork. Another practical point is that you can pay on site with Kaspi QR, Kaspi Red, card, cash, or bank transfer, without transferring money through an intermediary. When a direct contractor provides the service, warranty and responsibility aren't diluted between a dispatcher and a subcontractor.
Warranty and payment are what appliance owners clarify before calling a specialist. Let's break down exactly what our warranty covers, why the price only appears after inspection, and how payment works.
We give a 1-year warranty on labor and parts — if the component fails again, the technician will sort it out under warranty. The coverage applies to both: the quality of the repair and the installed part. For a Gorenje microwave owner, this means that a repeat visit for the same component doesn't turn into a new job with a new estimate. The specialist who handled the order knows the history of that specific appliance and can pinpoint the cause of the repeat faster. The warranty on parts is just as important as on labor: a defective new part is rare, but it's the most common cause of a repeat breakdown. That's why when we hand over the component, we record which part was installed — it makes it easier to prove a manufacturing defect.
Diagnostics are free with us, and the specialist gives you the price after them — once it's clear which Gorenje component has failed. The inspection shows what exactly needs replacement or adjustment: magnetron, high-voltage diode, capacitor, transformer, control panel. It's impossible to give an honest figure before disassembly and testing — there are too many variables hidden inside the case. The cost depends on the component and the model, so quoting it over the phone before inspection means guessing; the exact amount comes after the check. In our experience, this approach saves time for both sides: you don't pay for the inspection, and you make the decision about the work with a specific figure in hand. The specialist explains which component is being replaced and why the appliance won't work without it.
You can pay via Kaspi QR, Kaspi Red, card, cash or bank transfer, and you choose the format — at home or at the service center — together with the technician after the inspection. A call-out within the city takes up to 60 minutes, so the check usually doesn't take all day. If the breakdown requires workshop conditions, the appliance is accepted at the service center: the technician records the model, condition of the case, and included items, and you pick up the appliance after an on-site check. In our experience, it's more convenient to discuss the payment method right when agreeing on the work — that way the money question is settled before the appliance is back in your kitchen. For the owner, it's also a way to compare the amount with what the technician explained during the inspection: the list of work and replaced parts is discussed before service begins, not after. Payment is made in the agreed form, with no surprises or extra charges along the way.
A malfunction in the oven almost always fits into a few familiar scenarios — from no heating to sparking and a code on the display. Here's what to keep in mind before calling a technician.
40brands
Choose a brand to see its page with the services and models we cover.
Tech Service technicians repair other appliances too — with the same 1-year warranty on labour and parts.
Refrigerator Repair in Almatyfrom 3 000 ₸
Washing Machine Repair in Almatyfrom 3 000 ₸
Dishwasher Repair in Almatyfrom 3 500 ₸
Oven Repair in Almatyfrom 3 000 ₸
Cooktop Repair in Almatyfrom 3 500 ₸
Air Conditioner Repair in Almatyfrom 3 500 ₸
Boiler and Water Heater Repair in Almatyfrom 2 500 ₸
Freezer Repair in Almatyfrom 6 000 ₸
Tumble Dryer Repair in Almatyfrom 5 000 ₸
Coffee Machine Repair in Almatyfrom 2 500 ₸
Robot Vacuum Cleaner Repair in Almatyfrom 3 500 ₸
Vacuum Cleaner Repair in Almatyfrom 1 500 ₸
Microwave Oven Repair in Almatyfrom 2 000 ₸
Hair Dryer Repair in Almatyfrom 1 500 ₸
Iron Repair in Almatyfrom 3 000 ₸
Electric Kettle Repair in Almatyfrom 2 500 ₸
Mixer Repair in Almatyfrom 2 500 ₸
Multicooker Repair in Almatyfrom 500 ₸












